nvent FLEXCOND50 User manual

INSTRUCTION SHEET
NVENT ERIFLEX FLEXBUS SUPPORTS AND BRACING SYSTEM
FLEXCOND50 / FLEXCOND100
WARNING:
1. nVent products shall be installed and used only as indicated in nVent product instruction sheets and training materials. Instruction sheets are available at www.nVent.com and from your nVent
customer service representative.
2. nVent products must never be used for a purpose other than the purpose for which they were designed or in a manner that exceeds specified load ratings.
3. All instructions must be completely followed to ensure proper and safe installation and performance.
4. Improper installation, misuse, misapplication or other failure to completely follow nVent's instructions and warnings may cause product malfunction, property damage, serious bodily injury and/or death,
and void your warranty.
SAFETY INSTRUCTIONS: All governing codes and regulations and those required by the job site must be observed. Always use appropriate safety equipment such as eye protection, hard hat, and
gloves as appropriate to the application.
nVent, nVent CADDY, nVent ERICO Cadweld, nVent ERICO Critec, nVent ERICO, nVent ERIFLEX, and nVent LENTON are owned by nVent or its global affiliates. All other trademarks are the
property of their respective owners. nVent reserves the right to change specifications without prior notice.
TECHNICAL SUPPORT:
www.nVent.com IP8610_C 1 of 7 ©2021-2022 nVent All Rights Reserved
L1
①
②
≥10mm
℄
7
E1
S
E1
S
L1
③
≥30m
m
TQ = 6Nm
7
Lr
④
CLIC
CLIC
CLIC
10

INSTRUCTION SHEET
NVENT ERIFLEX FLEXBUS SUPPORTS AND BRACING SYSTEM
FLEXCOND50 / FLEXCOND100
WARNING:
1. nVent products shall be installed and used only as indicated in nVent product instruction sheets and training materials. Instruction sheets are available at www.nVent.com and from your nVent
customer service representative.
2. nVent products must never be used for a purpose other than the purpose for which they were designed or in a manner that exceeds specified load ratings.
3. All instructions must be completely followed to ensure proper and safe installation and performance.
4. Improper installation, misuse, misapplication or other failure to completely follow nVent's instructions and warnings may cause product malfunction, property damage, serious bodily injury and/or death,
and void your warranty.
SAFETY INSTRUCTIONS: All governing codes and regulations and those required by the job site must be observed. Always use appropriate safety equipment such as eye protection, hard hat, and
gloves as appropriate to the application.
nVent, nVent CADDY, nVent ERICO Cadweld, nVent ERICO Critec, nVent ERICO, nVent ERIFLEX, and nVent LENTON are owned by nVent or its global affiliates. All other trademarks are the
property of their respective owners. nVent reserves the right to change specifications without prior notice.
TECHNICAL SUPPORT:
www.nVent.com IP8610_C 2 of 7 ©2021-2022 nVent All Rights Reserved
⑤
⑥
TQ = 6Nm
1
0
⑦
⑧
CLIC
CLIC
CLIC
CLIC
CLIC
TQ = 6Nm
10
10
10
⑨
CLIC
CLIC

INSTRUCTION SHEET
NVENT ERIFLEX FLEXBUS SUPPORTS AND BRACING SYSTEM
FLEXCOND50 / FLEXCOND100
WARNING:
1. nVent products shall be installed and used only as indicated in nVent product instruction sheets and training materials. Instruction sheets are available at www.nVent.com and from your nVent
customer service representative.
2. nVent products must never be used for a purpose other than the purpose for which they were designed or in a manner that exceeds specified load ratings.
3. All instructions must be completely followed to ensure proper and safe installation and performance.
4. Improper installation, misuse, misapplication or other failure to completely follow nVent's instructions and warnings may cause product malfunction, property damage, serious bodily injury and/or death,
and void your warranty.
SAFETY INSTRUCTIONS: All governing codes and regulations and those required by the job site must be observed. Always use appropriate safety equipment such as eye protection, hard hat, and
gloves as appropriate to the application.
nVent, nVent CADDY, nVent ERICO Cadweld, nVent ERICO Critec, nVent ERICO, nVent ERIFLEX, and nVent LENTON are owned by nVent or its global affiliates. All other trademarks are the
property of their respective owners. nVent reserves the right to change specifications without prior notice.
TECHNICAL SUPPORT:
www.nVent.com IP8610_C 3 of 7 ©2021-2022 nVent All Rights Reserved
25mm
x2 Min
Option 1
24mm
D
6
D
!
7
1: ②-④
2: ⑥-⑨
1: ②-④
2: ⑥-⑨
6
10

INSTRUCTION SHEET
NVENT ERIFLEX FLEXBUS SUPPORTS AND BRACING SYSTEM
FLEXCOND50 / FLEXCOND100
WARNING:
1. nVent products shall be installed and used only as indicated in nVent product instruction sheets and training materials. Instruction sheets are available at www.nVent.com and from your nVent
customer service representative.
2. nVent products must never be used for a purpose other than the purpose for which they were designed or in a manner that exceeds specified load ratings.
3. All instructions must be completely followed to ensure proper and safe installation and performance.
4. Improper installation, misuse, misapplication or other failure to completely follow nVent's instructions and warnings may cause product malfunction, property damage, serious bodily injury and/or death,
and void your warranty.
SAFETY INSTRUCTIONS: All governing codes and regulations and those required by the job site must be observed. Always use appropriate safety equipment such as eye protection, hard hat, and
gloves as appropriate to the application.
nVent, nVent CADDY, nVent ERICO Cadweld, nVent ERICO Critec, nVent ERICO, nVent ERIFLEX, and nVent LENTON are owned by nVent or its global affiliates. All other trademarks are the
property of their respective owners. nVent reserves the right to change specifications without prior notice.
TECHNICAL SUPPORT:
www.nVent.com IP8610_C 4 of 7 ©2021-2022 nVent All Rights Reserved
①
②
③
Option 2
24mm
TQ = 6Nm
CABSBRKTE
CABSBRKTE
CABSBRKTT
!
L2 = L1 + 25mm
!
E2 = E1 + 12.5mm
CLIC
10
10
TQ = 6Nm
7
2: ⑥-⑨
1: ②
10
10
CLIC
CLIC

INSTRUCTION SHEET
NVENT ERIFLEX FLEXBUS SUPPORTS AND BRACING SYSTEM
FLEXCOND50 / FLEXCOND100
WARNING:
1. nVent products shall be installed and used only as indicated in nVent product instruction sheets and training materials. Instruction sheets are available at www.nVent.com and from your nVent
customer service representative.
2. nVent products must never be used for a purpose other than the purpose for which they were designed or in a manner that exceeds specified load ratings.
3. All instructions must be completely followed to ensure proper and safe installation and performance.
4. Improper installation, misuse, misapplication or other failure to completely follow nVent's instructions and warnings may cause product malfunction, property damage, serious bodily injury and/or death,
and void your warranty.
SAFETY INSTRUCTIONS: All governing codes and regulations and those required by the job site must be observed. Always use appropriate safety equipment such as eye protection, hard hat, and
gloves as appropriate to the application.
nVent, nVent CADDY, nVent ERICO Cadweld, nVent ERICO Critec, nVent ERICO, nVent ERIFLEX, and nVent LENTON are owned by nVent or its global affiliates. All other trademarks are the
property of their respective owners. nVent reserves the right to change specifications without prior notice.
TECHNICAL SUPPORT:
www.nVent.com IP8610_C 5 of 7 ©2021-2022 nVent All Rights Reserved
①
②
1: ②
!
L2 = L1 + 25mm
!
E2 = E1 + 12.5mm
1
0
TQ = 6Nm
2: ④, ⑥-⑨
8,9
10
1
2
3
4
5
!
10
10
10

INSTRUCTION SHEET
NVENT ERIFLEX FLEXBUS SUPPORTS AND BRACING SYSTEM
FLEXCOND50 / FLEXCOND100
WARNING:
1. nVent products shall be installed and used only as indicated in nVent product instruction sheets and training materials. Instruction sheets are available at www.nVent.com and from your nVent
customer service representative.
2. nVent products must never be used for a purpose other than the purpose for which they were designed or in a manner that exceeds specified load ratings.
3. All instructions must be completely followed to ensure proper and safe installation and performance.
4. Improper installation, misuse, misapplication or other failure to completely follow nVent's instructions and warnings may cause product malfunction, property damage, serious bodily injury and/or death,
and void your warranty.
SAFETY INSTRUCTIONS: All governing codes and regulations and those required by the job site must be observed. Always use appropriate safety equipment such as eye protection, hard hat, and
gloves as appropriate to the application.
nVent, nVent CADDY, nVent ERICO Cadweld, nVent ERICO Critec, nVent ERICO, nVent ERIFLEX, and nVent LENTON are owned by nVent or its global affiliates. All other trademarks are the
property of their respective owners. nVent reserves the right to change specifications without prior notice.
TECHNICAL SUPPORT:
www.nVent.com IP8610_C 6 of 7 ©2021-2022 nVent All Rights Reserved

INSTRUCTION SHEET
NVENT ERIFLEX FLEXBUS SUPPORTS AND BRACING SYSTEM
FLEXCOND50 / FLEXCOND100
WARNING:
1. nVent products shall be installed and used only as indicated in nVent product instruction sheets and training materials. Instruction sheets are available at www.nVent.com and from your nVent
customer service representative.
2. nVent products must never be used for a purpose other than the purpose for which they were designed or in a manner that exceeds specified load ratings.
3. All instructions must be completely followed to ensure proper and safe installation and performance.
4. Improper installation, misuse, misapplication or other failure to completely follow nVent's instructions and warnings may cause product malfunction, property damage, serious bodily injury and/or death,
and void your warranty.
SAFETY INSTRUCTIONS: All governing codes and regulations and those required by the job site must be observed. Always use appropriate safety equipment such as eye protection, hard hat, and
gloves as appropriate to the application.
nVent, nVent CADDY, nVent ERICO Cadweld, nVent ERICO Critec, nVent ERICO, nVent ERIFLEX, and nVent LENTON are owned by nVent or its global affiliates. All other trademarks are the
property of their respective owners. nVent reserves the right to change specifications without prior notice.
TECHNICAL SUPPORT:
www.nVent.com IP8610_C 7 of 7 ©2021-2022 nVent All Rights Reserved
CONFIGURATION
FLEXCOND50
FLEXCOND100
L1
# L1
E1
S
Lr
# Lr
D
L1
# L1
E1
S
Lr
# Lr
D
3P (I)
287,5
3
12,5
87,5
160
4
262,5
325
3
12,5
100
195
4
300
112,5
7
12,5
87,5
435
2
87,5
162,5
7
12,5
137,5
195
2
137,5
287,5
3
12,5
87,5
160
4
262,5
437,5
3
12,5
137,5
300
4
412,5
3P (II)
550
3
12,5
87,5
160
7
525
625
3
12,5
100
195
7
600
287,5
5
12,5
87,5
255
4
262,5
325
5
12,5
100
360
4
300
200
7
12,5
87,5
435
3
175
300
7
12,5
137,5
435
3
275
287,5
5
12,5
87,5
300
4
262,5
437,5
5
12,5
137,5
300
4
412,5
3P + N (I)
375
3
12,5
87,5
160
5
350
425
3
12,5
100
195
5
400
200
5
12,5
87,5
255
3
175
225
5
12,5
100
360
3
200
200
5
12,5
87,5
300
3
175
300
5
12,5
137,5
300
3
275
112,5
9
12,5
87,5
570
2
87,5
162,5
9
12,5
137,5
570
2
137,5
375
3
12,5
87,5
160
3
350
575
3
12,5
137,5
195
3
550
3P + N (II)
725
3
12,5
87,5
160
9
700
825
3
12,5
100
195
9
800
375
5
12,5
87,5
255
5
350
425
5
12,5
100
360
5
400
200
9
12,5
87,5
570
3
175
300
9
12,5
137,5
570
3
275
375
5
12,5
87,5
300
5
350
575
5
12,5
137,5
300
5
550