NXP Semiconductors DSP56362EVM User manual

DSP56362EVMUM/AD
02/01
REV # 2.5
DSP56362EVM
User’s Manual
Motorola, Incorporated
Semiconductor Products Sector
6501 William Cannon Drive West
Austin, TX 78735-8598
Freescale Semiconductor, I
Freescale Semiconductor, Inc.
For More Information On This Product,
Go to: www.freescale.com
nc...

This document (and other documents) can be viewed on the World Wide
Web at http://www.motorola-dsp.com.
This manual is one of a set of three documents. You need the following
manuals to have complete product information: Family Manual, User’s
Manual, and Technical Data.
OnCE is a trademark of Motorola, Inc.
 MOTOROLA INC. 1999, 2000, 2001
Rev. 2.5; published 02/01
Order this document by DSP56362EVMUM/AD
Motorola reserves the right to make changes without further notice to any products herein to improve
reliability, function, or design. Motorola does not assume any liability arising out of the application or use
of any product or circuit described herein; neither does it convey any license under its patent rights nor the
rights of others. Motorola products are not authorized for use as components in life support devices or
systems intended for surgical implant into the body or intended to support or sustain life. Buyer agrees to
notify Motorola of any such intended end use whereupon Motorola shall determine availability and
suitability of its product or products for the use intended. Motorola and are registered trademarks of
Motorola, Inc. Motorola, Inc. is an Equal Employment Opportunity /Affirmative Action Employer.
Freescale Semiconductor, I
Freescale Semiconductor, Inc.
For More Information On This Product,
Go to: www.freescale.com
nc...

MOTOROLA iii
CONTENTS
Paragraph
Number Title Page Number
1.1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-1
1.2 Feature Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-2
1.3 Hardware Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-3
1.3.1 Evaluation Module Hardware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-3
1.3.2 User Supplied Demonstration Hardware . . . . . . . . . . . . . . . . . . . . . .1-3
1.3.3 Required Software Development Hardware. . . . . . . . . . . . . . . . . . . .1-4
1.4 Installation Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-5
1.4.1 Hardware Connections. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-5
1.4.2 PC And Power Connections. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-6
1.4.3 Software Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-6
2.1 Analog I/O Description. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-3
2.1.1 A/D Converter Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-5
2.1.1.1 Serial Data Input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-6
2.1.1.2 A/D Converter Reset. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-6
2.1.2 D/A Converters. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-7
2.1.2.1 Software Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-7
2.1.2.2 Serial Data Outputs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-9
2.1.2.3 D/A Converter Reset. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-9
2.1.3 Analog I/O Blcok Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-10
2.2 Digital I/O. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-11
2.2.1 S/PDIF Receiver. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-12
2.2.2 Digital Audio Transmitter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-13
2.2.3 S/PDIF Transmitter. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-13
2.2.4 Digital I/O Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-14
2.3 DSP Clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-15
2.4 Host Microcontroller Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-15
2.5 RS-232/MC68HC711 Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-16
2.6 PLD Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-17
2.7 Operating Mode Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-21
2.8 Expansion Port. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-23
2.9 OnCE Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-24
2.9.1 Direct OnCE Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-24
2.9.2 RS-232/OnCE Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-25
2.10 Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-26
2.10.1 SRAM. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-28
2.10.2 EPROM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-28
2.10.3 External Memory Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . .2-28
2.11 Power Supply. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-29
2.11.1 Power Supply Block Diagram. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-29
2.11.2 DSP Power. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-30
3.1 Documentation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-1
5.1 Evaluation Module Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-1
5.2 PLD Equations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-6
Freescale Semiconductor, I
Freescale Semiconductor, Inc.
For More Information On This Product,
Go to: www.freescale.com
nc...

iv MOTOROLA
CONTENTS
Paragraph
Number Title Page Number
6.1 Pass-Through Operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-1
6.1.1 Receive Interrupt Service Routines . . . . . . . . . . . . . . . . . . . . . . . . . .6-1
6.1.2 Transmit nterrupt Service Routines . . . . . . . . . . . . . . . . . . . . . . . . . .6-3
6.1.3 Main Loop . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-5
6.2 Digital Pass-Through. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-6
6.3 Digital Pass-Through Jumper Settings . . . . . . . . . . . . . . . . . . . . . . . . . .6-7
6.4 Analog Pass-Through . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-8
6.5 Analog Pass-Through Jumper Settings. . . . . . . . . . . . . . . . . . . . . . . . . .6-9
Freescale Semiconductor, I
Freescale Semiconductor, Inc.
For More Information On This Product,
Go to: www.freescale.com
nc...

MOTOROLA v
List of Figures
Figure
Number Title Page Number
1-1 Figure1-1 Block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-1
1-2 Consumer Audio Evaluation and Prototyping Platform. . . . . . . . . . . . . . . .1-2
1-3 Demonstration Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-4
1-4 DSP56362EVM Cable Connections. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-6
2-1 Default Jumper Locations Shown for Digital Input . . . . . . . . . . . . . . . . . . .2-2
2-2 Analog I/O Connectors. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-3
2-3 Input Clocking Mode Header PLD. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-4
2-4 JP24, A/D Sampling Rate Select Header . . . . . . . . . . . . . . . . . . . . . . . . . . .2-5
2-5 D/A Control Header . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-8
2-6 Analog I/O Block Diagram. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-10
2-7 Digital I/O Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-11
2-8 Input Clocking Mode Header . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-12
2-9 Primary Digital I/O Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-14
2-10 Secondary Digital I/O Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-14
2-11 Host Microcontroller Block Diagram. . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-15
2-12 RS-232 Communication Select. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-16
2-13 PLD Clock Outputs - S/PDIF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-17
2-14 PLD Clock Outputs - A/D . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-18
2-15 DSP Clock Source . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-19
2-16 HC08 Reset. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-20
2-17 Operating Mode Jumper (JP8) Location. . . . . . . . . . . . . . . . . . . . . . . . . . .2-22
2-18 Expansion Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-23
2-19 RS-232 Communication Select. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-25
2-20 Memory Header Locations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-27
2-21 External Memory Interface Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-28
2-22 Evaluation Module Power Supply Diagram. . . . . . . . . . . . . . . . . . . . . . . .2-29
2-23 DSP Power Jumpers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-30
6-1 Receive Input Buffer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-2
6-2 Receive Interrupt Service Routines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-2
6-3 Transmit Output Buffer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-3
6-4 Transmit Interrupt Service Routines. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-4
6-5 Passthrough Main Loop . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-5
6-6 LCD Pass-through Screen. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-6
6-7 Jumper Settings for Digital Pass-Through . . . . . . . . . . . . . . . . . . . . . . . . . .6-7
6-8 LCD pass-through Screen. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-8
6-9 Jumper Settings for Analog Pass-Through. . . . . . . . . . . . . . . . . . . . . . . . . .6-9
Freescale Semiconductor, I
Freescale Semiconductor, Inc.
For More Information On This Product,
Go to: www.freescale.com
nc...

vi MOTOROLA
List of Figures
Figure
Number Title Page Number
Freescale Semiconductor, I
Freescale Semiconductor, Inc.
For More Information On This Product,
Go to: www.freescale.com
nc...

MOTOROLA vii
List of Tables
Table
Number Title Page Number
2-1 Jumpers as Installed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-1
2-2 Analog I/O Clocking Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-4
2-3 A/D Sampling Rate Select . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-5
2-4 System, Frame Sync and Serial Clocks . . . . . . . . . . . . . . . . . . . . . . . . . . .2-6
2-5 DAC Default Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-7
2-6 D/A Software Mode Control. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-8
2-7 D/A Serial Data Outputs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-9
2-8 Digital I/O Clocking Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-11
2-9 S/PDIF Receiver Select . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-12
2-10 S/PDIF Transmitter System Clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-13
2-11 S/PDIF Transmitter Serial Data Output . . . . . . . . . . . . . . . . . . . . . . . . . .2-13
2-12 RS232 Communication with MC68HC711 . . . . . . . . . . . . . . . . . . . . . . .2-16
2-13 D/A Converter Select . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-19
2-14 DSP Operating Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-21
2-15 Expansion Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-23
2-16 OnCE Port Connector. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-24
2-17 RS-232 Communications with MC68HC705. . . . . . . . . . . . . . . . . . . . . .2-25
2-18 Memory Line Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-26
2-19 DSP Power Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-30
3-1 Documentation Location. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-1
5-1 Evaluation Module Bill of Materials . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-1
6-1 Digital Input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-6
6-2 Analog Input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-8
Freescale Semiconductor, I
Freescale Semiconductor, Inc.
For More Information On This Product,
Go to: www.freescale.com
nc...

viii MOTOROLA
List of Tables
Table
Number Title Page Number
Freescale Semiconductor, I
Freescale Semiconductor, Inc.
For More Information On This Product,
Go to: www.freescale.com
nc...

MOTOROLA About This Manual ix
About This Manual
This manual describes the functionality and use of the DSP56362EVM (Evaluation Mod-
ule). Motorola offers several different ROM software versions of the DSP56362 that are
supported with this EVM. DSP56362 ROM versions are available to support technolo-
gies from third party licenses, such as Dolby Laboratories™, and DTS™.
Users can upgrade this EVM because critical components such as the DSP56362,
MC68HC711, and EPROM are socketed. For information on other ROM versions, con-
tact Motorola, or visit the website at:
http://mot-sps.com/ADC/audio_solutions.html
Organization
This book is organized into 6 sections:
• Overview
• Setup and Operation
• Component Datasheets
• Schematics
• Bill of Materials
• Running the Pass-through code
Suggested Reading
Additional reading that provides background for the information in this guide as well as
general information about the Multimedia Architecture:
• IEC 958 Digital Audio Interface Standard
• DSP56362 User’s Manual
Conventions
This document uses the following notational conventions:
• Messages displayed on screen and example code are presented in the courier
fixed-width font.
• Information entered by users is shown in bold font.
• File names , program names , and directories are in italics.
Freescale Semiconductor, I
Freescale Semiconductor, Inc.
For More Information On This Product,
Go to: www.freescale.com
nc...

x About This Manual MOTOROLA
Freescale Semiconductor, I
Freescale Semiconductor, Inc.
For More Information On This Product,
Go to: www.freescale.com
nc...

OVERVIEW
Introduction
MOTOROLA DSP56362EVM User’s Manual 1-1
SECTION 1
OVERVIEW
1.1 INTRODUCTION
This section describes the basic features, hardware description and installation of the
DSP56362EVM (Evaluation Module). The manual also describes the equipment and software
required. Code samples and self-test code are provided on an accompanying software diskette.
The schematic diagram and parts of the Evaluation Module are included in this manual. This
is a generic hardware/software configuration. Upgrade kits are available for more specialized
and advanced applications. Some upgrade kits require licensing agreements with other
companies (DTS™, Dolby Digital™, etc.).The block diagram is shown in Figure1-1.
Figure 1-1 Figure1-1 Block diagram
DSP56362
DEBUG
LCD Display
MC68HC711
Buttons/
Keypad
SDI0
SDI1
SDI0
SDI1
SDI2
SDI3
D/A
PCM1716
D/A
PCM1716
D/A
PCM1716
D/A
PCM1716
A/D
PCM1800
S/PDIF
Receiver
S/PDIF
Transmitter
SRAM EPROM
128K x 24 128K x 8
External Memory
User Interface
JTAG
RS-232
SHI
Analog Input
Digital Input
Optional Output
For Testing
L/R Main
Center/Sub
L/R Surround
Headphone Mixdown
or Aux Surround
Computer
68 HC705C8A
Freescale Semiconductor, I
Freescale Semiconductor, Inc.
For More Information On This Product,
Go to: www.freescale.com
nc...

1-2 DSP56362EVM User’s Manual MOTOROLA
OVERVIEW
Feature Description
1.2 FEATURE DESCRIPTION
The DSP56362EVM is a low-cost platform for multichannel digital audio applications design,
prototyping, and development. See Figure1-2.
Figure 1-2 Consumer Audio Evaluation and Prototyping Platform
The fully assembled and tested circuit board contains the following.
• 24-bit DSP56362 Digital Signal Processor operating at 80-100MHz.
• 128k x 24-bits of external SRAM and 128k x 8-bits of EPROM.
• One 20-bit stereo Analog-to-Digital converter (ADC), four 24-bit stereo
Digital-to-Analog converters (DACs).
• RCA jacks for all analog audio input and output connections.
Freescale Semiconductor, I
Freescale Semiconductor, Inc.
For More Information On This Product,
Go to: www.freescale.com
nc...

OVERVIEW
Hardware Description
MOTOROLA DSP56362EVM User’s Manual 1-3
• Optical and transformer-isolated electrical S/PDIF stereo digital audio inputs and
outputs.
• 50-pin expansion connector that provides capability for expansion and/or substitution
of other input/output peripherals. This connector also simplifies interprocessor
communication between other Motorola Evaluation Modules.
• Socketed MC68HC711E20 that allows users to substitute custom MC68HC711 code
(allows connection to MC68HC11 emulation systems).
• 2 line x 20 character Liquid Crystal Display (LCD) and four soft switches for user
interface.
• MC68HC705C8 microcontroller that performs RS-232-to-OnCE port command
conversions.
1.3 HARDWARE DESCRIPTION
This section gives a brief summary of the Evaluation Module hardware supplied, and
description of the hardware required to use the Evaluation Module.
1.3.1 EVALUATION MODULE HARDWARE
• Evaluation Module board
• Domain Technologies CD
• Debug - Evaluation Module manual is provided on the CD-DSP56362EVM User’s
Manual (this document)
1.3.2 USER SUPPLIED DEMONSTRATION HARDWARE
• An AC-3 or PCM bitstream source such as a Laserdisc, DAT, CD source, or VHS.
• An audio amplifier that can drive headphones or speakers as shown in Figure1-3.
• A 7.5- 9V 1 amp AC/DC power supply (7.5 volts is preferred).
Freescale Semiconductor, I
Freescale Semiconductor, Inc.
For More Information On This Product,
Go to: www.freescale.com
nc...

1-4 DSP56362EVM User’s Manual MOTOROLA
OVERVIEW
Hardware Description
Figure 1-3 Demonstration Configuration
1.3.3 REQUIRED SOFTWARE DEVELOPMENT HARDWARE
• A personal computer with x386 or higher processor, minimum 2 Mbytes of memory,
CD ROM driver, and a serial port that is capable of at least 19,200 bits-per-second
data transfer rate.
• Windows 95/98 or NT operating system
• An RS-232 cable (DB9 male to DB9 female)
Power Amp
Laserdisc/DVD Player Listener
DSP56362EVM
Subwoofer
(unpowered)
Subwoofer
(powered)
DSP56362
68HC11E9 BB1716
BB1716
BB1716 BB1716
ISPLS
12032
DIR1700
CS8414
CS8404
BB1800
P2
P3 P1
JP12
JP16
JP13
JP14 JP8
JP31
JP11
JP15
JP7 JP5
JP4
JP20
JP24 JP19
JP2
JP25JP23JP21
JP22
JP10
JP20
IR Rx
JP18
GS71108J-10 GS71108J-10 GS71108J-10
LR
Rs
Ls
C
Ra
La
Lin Rin
Elec.
out
Elec.
out
Opt.
in
Elec.
in
Sub
Freescale Semiconductor, I
Freescale Semiconductor, Inc.
For More Information On This Product,
Go to: www.freescale.com
nc...

OVERVIEW
Installation Procedures
MOTOROLA DSP56362EVM User’s Manual 1-5
1.4 INSTALLATION PROCEDURES
Installing the Evaluation Module requires four steps:
1. Preparing the board.
2. Connecting the board to the PC and power.
3. Installing the software on the PC.
4. Testing the installation.
1.4.1 HARDWARE CONNECTIONS
CAUTION
Because all electronic components are sensitive to the effects of electrostatic
discharge (ESD) damage, use correct procedures when handling all components in
this kit and inside the supporting PC. Use the following procedures to minimize the
possibility of ESD damage.
• Always handle all static-sensitive components in aprotected area, preferably a
lab with conductive (anti-static) flooring and bench surfaces.
• Always use grounded wrist straps when handling sensitive components.
• Never remove components from anti-static packaging until required for
installation.
• Always transport sensitive components in anti-static packaging.
Freescale Semiconductor, I
Freescale Semiconductor, Inc.
For More Information On This Product,
Go to: www.freescale.com
nc...

1-6 DSP56362EVM User’s Manual MOTOROLA
OVERVIEW
Installation Procedures
1.4.2 PC AND POWER CONNECTIONS
Figure1-4 shows the interconnection diagram for connecting the PC and the external power
supply to the Evaluation Module board.
Figure 1-4 DSP56362EVM Cable Connections
1. Connect the DB9P interface cable to the RS-232 port connection on the PC, and P1 on
the Evaluation Module board. This provides the connection to allow the PC to control
the board function.
2. Apply 7.5-9V AC/DC 1amp power to the P2 or P3 connector on the Evaluation
Module board.
3. The green Power LED will light when power is correctly applied.
1.4.3 SOFTWARE INSTALLATION
The Evaluation Module demonstration software consists of a Domain Technologies CD
containing Windows™ style user interface debug software and demonstration/test code.Use
the following steps to install the software:
1. Insert the Domain Technologies CD into the CD-ROM drive. Select and run the
program setup.exe. Choose DSP563xxEVM from the menu.
2. Choose Debug 56k from the menu.
3. A Software License Agreement will appear. To install EVM563xx, you must accept
this agreement. Click yes.
4. A new screen will appear. Fill in your name and company, then choose NEXT.
PC-compatible
Cable
Computer
DB9 Interface
DSP56362EVM
P1
Connect cable
to RS-232 port P2
External
7-9V
Power
or
P3
Freescale Semiconductor, I
Freescale Semiconductor, Inc.
For More Information On This Product,
Go to: www.freescale.com
nc...

OVERVIEW
Installation Procedures
MOTOROLA DSP56362EVM User’s Manual 1-7
5. Setup will install EVM563xx in C:\Program Files\DomTech\EVM563xx, then
choose NEXT.
6. Setup will add program icons to the Program Folder. You may type a new folder
name, or select one from the existing Folders list. Click NEXT to continue.
7. Setup has enough information to start copying the program files. Click NEXT to begin
copying files.
8. The screen will clear and the Domain menu will appear. Click EXIT.
Freescale Semiconductor, I
Freescale Semiconductor, Inc.
For More Information On This Product,
Go to: www.freescale.com
nc...

1-8 DSP56362EVM User’s Manual MOTOROLA
OVERVIEW
Installation Procedures
Freescale Semiconductor, I
Freescale Semiconductor, Inc.
For More Information On This Product,
Go to: www.freescale.com
nc...

SETUP AND OPERATION
MOTOROLA DSP56362EVM User’s Manual 2-1
SECTION 2
SETUP AND OPERATION
This section describes the setup options that you need to be familiar with. Jumpers on the
Evaluation Module are provided to configure the board for various operations. The factory
default jumpers are shown in Table 2-1. The locations of the headers for jumpers is shown in
Figure 2-1.l
Table 2-1 Jumpers as Installed
Jumper From To Jumper From To Jumper From To
JP1 12
JP12
34
JP20 12
JP2 12 56 JP21 12
JP3 12 78 JP23 12
JP4 12 910 JP24 12
JP5 1 2 11 12 JP25 12
JP6 1 2 13 14 JP27 12
JP7 1 2 17 18 JP28 13
JP8 3 4 19 20 2 4
7 8 21 22
JP31
23
23 24 5 6
25 26 8 9
29 30 11 12
31 32 14 15
33 34 S6 1
35 36
43 44
45 46
47 48
Freescale Semiconductor, I
Freescale Semiconductor, Inc.
For More Information On This Product,
Go to: www.freescale.com
nc...

2-2 DSP56362EVM User’s Manual MOTOROLA
SETUP AND OPERATION
Figure 2-1 Default Jumper Locations Shown for Digital Input
Freescale Semiconductor, I
Freescale Semiconductor, Inc.
For More Information On This Product,
Go to: www.freescale.com
nc...