NXP Semiconductors freescale MC9S08GW64 User manual

TOWER SYSTEMLab Tutorial for TWR-S08GW64
MC9S08GW64
LCD segment MCU for flow meters
and energy metering applications

TOWER SYSTEMTOWER SYSTEM
Tamper Switch (SW4)
User Switch (SW3)
User Switch (SW5)
Reset Switch
IRQ Switch
USB Connector
MC9S08GW64
Primary
Connector
RS232 Port
Potentiometer to
Control the Vrms
Potentiometer to
Control Irms
LCD Glass
Secondary
Connector
Figure 1: TWR-S08GW64
TWR-S08GW64-KIT
Freescale Tower System
The TWR-S08GW64 module is part of the Freescale Tower System,
a modular development platform that enables rapid prototyping and
tool re-use through reconfigurable hardware. Take your design to the
next level and begin constructing your Tower System today. The
TWR-S08GW64-KIT comes with two elevator modules (TWR-ELEV)
and a prototype module (TWR-PROTO).
Get to Know the TWR-S08GW64

TOWER SYSTEMLab Tutorial for TWR-S08GW64
Freescale provides free lab diagnostic code to provide hands-on
experience and demonstrate the capabilities of the MC9S08GW64 on
TWR-S08GW64.
Introduction
Included:
Lab 1:
• Displaysthecurrent,voltage,energy
and power factor
• Displaystheclock,calendarand
tampers registered
• Thevalueofthecurrent,voltageand
power factor can be varied using the
potentiometer
• Thevalueofthetampersregisteredcan
be varied using a switch
Lab 2:
• LCDallsegmentONforconnectivity
check
• LCDblinkmodesdemonstration
• LCDchargepumpandresistorbias
mode
• LCDprescalaroptions

TOWER SYSTEM
Please follow the jumper
settings below before running
the Lab tutorial.
1 2 3
J6
1 2 3
J3
1 2 3
J1
246
135
J14
1
2
3
1
2
3
J15 J16
1
2
3
J10
J7
Connectbetween2and3inJ6toget
power from the regulator.
1 2 3
J6
1 2 3
J3
1 2 3
J1
246
135
J14
1
2
3
1
2
3
J15 J16
1
2
3
J10
J7
ConnectJ7topoweruptheMCUfrom
theoutputofJ6.
1 2 3
J6
1 2 3
J3
1 2 3
J1
246
135
J14
1
2
3
1
2
3
J15 J16
1
2
3
J10
J7
Connectbetween2and3inbothJ1and
J3toconnectthedebuggerinterfaceto
GW64.
J10
J3
J6
J1
TWR-S08LGW64 Jumper Settings
J15 J16 J7 J14

TOWER SYSTEMLab Tutorial for TWR-S08GW64
1 2 3
J6
1 2 3
J3
1 2 3
J1
246
135
J14
1
2
3
1
2
3
J15 J16
1
2
3
J10
J7
Connectbetween1and2forbothJ15
andJ16toconnecttheoutputofQE8
toADC1andADC2forsignalsimulation
input.
1 2 3
J6
1 2 3
J3
1 2 3
J1
246
135
J14
1
2
3
1
2
3
J15 J16
1
2
3
J10
J7
Connectbetween2and3forJ10to
connect Switch 4 as the tamper 1 input.
1 2 3
J6
1 2 3
J3
1 2 3
J1
246
135
J14
1
2
3
1
2
3
J15 J16
1
2
3
J10
J7
Connectbetween4and6andbetween3
and5forJ14toconnecttheGW64serial
datatoRS232.

TOWER SYSTEM
Open CodeWarrior and
the Project
1. Completethesetupinstructions
intheQuickStartGuide.Besure
CodeWarriorv10.0isinstalled.
2. OpenCodeWarriorfor
microcontrollers. From the Windows
start menu, you can locate it using
“Programs>FreescaleCodeWarrior>
CWforMCUv10.0>CodeWarrior.”
3. Choosethe“StartUsingCodeWarrior”
button.
4. DownloadtheprojectDemo_Board_
Application_Software.zip(LAB1)and
LCDLAB.zip(LAB2).
 UnzipandsavethefoldersDemo_
Board_Application_SoftwareandLCD
LABonthedesktop.
5. UsingCodeWarrior,clickFile>Open
andbrowsetoDesktop/Demo_Board_
Application_Software/demo_board.
mcpforLAB1
Desktop/LCDLAB/build/mwerks/evb/
LAB_LCD.mcpforLAB2
Install the GW64
Service Pack
1. OpentheCodeWarriorwindow.
2. Gotothe“Help”menu.
3. Select“InstallNewSoftware”inthe
drop down menu.
4. Ensure the link below is in your “Work
With”textbox-
http://freescale.com/lgfiles/updates/
Eclipse/MCU/com.freescale.mcu.
updatesite
5. Selectthecheckboxfor“MCU10.0
ServicePackforMC9S08GW64and
MC9S08GW32”
STEP
1
STEP
2
Step-by-Step Guide

TOWER SYSTEMLab Tutorial for TWR-S08GW64
Open the Source Code
1. Inthe“File”menugoto“Import”as
shown.
2. Expand“General”andselect
“CodeWarriorClassicProject
Importer”asshown.Click“Next.”
STEP
3

TOWER SYSTEM
3. Browsetothefolderwherethecode
is stored and select the .mcp file and
click“Finish.”
4. Theprojectdirectorystructurewillbe
visible as shown.
IntheCodeWarriorwindow,doubleclick
onMC9S08GW64.hintheLibsfolderand
paste the following line in the file: #pragma
OPTIONADDS08CFv1Compatible
“-BfaGapLimitBits4294967295”

TOWER SYSTEMLab Tutorial for TWR-S08GW64
Set Up the TWR-
9S08GW64 Module
Basic steps for the Tower System
hardware installation
FortheLCDLAB,thefollowingcardsof
the Tower System are required:
1. Tower System Primary Elevator
2. Tower System Secondary Elevator
3. TowerSystemSerialModule
4. TowerSystemGW64Controller
Module
HowtoConnect:
1. There are four slots each on Primary
and Secondary Elevator card. All four
slots are identical to each other.
2. TaketheGW64Controllercardand
insertthePRIMARYconnectorsidein
thePrimaryElevator,matchingthe“B”
marking of the Elevator card and the
controller card in any of the four slots.
3. TaketheSerialModuleandinsert
thePRIMARYconnectorsideinthe
PrimaryElevator,matchingthe“B”
marking of the Elevator card and
theSerialModuleinanyofthethree
remaining slots.
4. Take the Secondary Elevator card and
fit it on the other side of the GW64
ControllerandtheSerialModulecard,
againmatchingthe“B”markingso
that it forms a Tower-like structure.
The Tower System is now in place.
STEP
4

TOWER SYSTEM
1. Power up the Tower System by
pluggingtheUSBcablebetweenthe
PC(USBType-AFemaleconnector)
and the Primary Elevator card
connectorJ5(MiniUSBType-B
connector)andthenswitchONthe
toggle switch (PWR SW) on the
Primary Elevator.
2. Connectthedebuggerfor
downloadingthecodefromthePCby
connectingtheUSBCablefromthe
PC(USBType-AFemaleconnector)
totheUSBMultilinkInterface(USB
Type-BFemaleconnector)and
connecttheotherendoftheUSB
MultilinkInterfacetotheJ2ofthe
GW64ControllerCard.
Note:TheredwireshouldmatchPin1ofJ2.