Oasis SFG Series User manual

SFG SERIES TOP MOUNT FIBREGLASS MEDIA FILTER INSTALLATION AND OPERATION MANUAL Page 1of 23
FOR QUICK REFERENCE, RECORDS YOUR DETAILS HERE.
Model No:
Serial No:
Purchase Date:
Installer:
Warranty Registered Online:
Yes / No
See page 19 for details
PRESSURE GAUGE READING RECORD
Initial Reading
Date
PSI
kPa
Date
PSI
kPa
Date
PSI
kPa
Date
PSI
kPa
Date
PSI
kPa
Date
PSI
kPa
Date
PSI
kPa
Date
PSI
kPa
Date
PSI
kPa
Date
PSI
kPa
Date
PSI
kPa
Date
PSI
kPa
Date
PSI
kPa
Date
PSI
kPa
Date
PSI
kPa
Date
PSI
kPa
Date
PSI
kPa
Date
PSI
kPa

SFG SERIES TOP MOUNT FIBREGLASS MEDIA FILTER INSTALLATION AND OPERATION MANUAL Page 2of 23
TABLE OF CONTENTS
1. IMPORTANT WARNINGS & SAFETY INSTRUCTIONS.............................................................. 3
2. GENERAL OVERVIEW................................................................................................................ 4
3. HOW IT WORKS.......................................................................................................................... 5
4. INSTALLATION............................................................................................................................ 6
Start-Up Procedure.................................................................................................................. 8
5. MULTIPORT CONTROL VALVE FUNCTIONS............................................................................ 9
6. BACKWASHING........................................................................................................................ 10
7. WINTERISING........................................................................................................................... 11
8. SYSTEM TROUBLESHOOTING................................................................................................ 11
9. POOL CHEMISTRY GUIDELINES............................................................................................. 13
10. PRO-ACTIVE MAINTENANCE PROGRAM............................................................................ 14
11. SPECIFICATIONS & DIMENSIONS...................................................................................... 15
12. REPLACEMENT PARTS OF FILTER..................................................................................... 16
SFG25-40.............................................................................................................................. 16
SFG25-50.............................................................................................................................. 17
SFG28-50, SFG32-50 & SFG36-50....................................................................................... 18
13. WARRANTY........................................................................................................................... 19
14. TECHNICAL SUPPORT......................................................................................................... 20
15. NOTES................................................................................................................................... 21

SFG SERIES TOP MOUNT FIBREGLASS MEDIA FILTER INSTALLATION AND OPERATION MANUAL Page 3of 23
1. IMPORTANT WARNINGS & SAFETY INSTRUCTIONS
IMPORTANT WARNINGS
This manual contains important information about the installation, operation and safe use of this
product. This information should be given to the owner and/or operator of this equipment. When
installing and using this equipment, basic safety precautions should always be followed. Failure
to follow safety warnings and instructions in this manual can result in serious injury and/or
damage to your equipment. Read and follow all warning notices and instructions which are
included in this manual.
Pool and Spa water circulation systems operate under hazardous pressure during start up, normal
operation, and after pump shut off. Stand clear of circulation system equipment during pump start-up.
Failure to follow safety and operation instructionscould result in violent separation of the pump housing
and cover, and/or filter housing and clamp due to pressure in the system, which could cause property
damage, severe personal injury, or death.
Before servicing pool and spa water circulation systems, all system and pump controls must be in the
off position and filter manual relief valve must be in open position. Before starting system pump, all
system valves must be set in a position that allows system water to return back to the pool.
DO NOT CHANGE FILTER CONTROL VALVE POSITION WHILST SYSTEM PUMP IS OPERATING.
Before starting system pump, fully open filter manual air relief valve.
Do not close filter manual air relief valve until a steady stream of water (not air) is discharged.
Cleaning the media filter by BACKWASHING and RINSING is essential to providing clean, safe and
healthy swimming water.
To reduce the risk of injury, DO NOT permit young children to use this product unless they have
been trained by the person responsible for their safety and they acknowledge their ability to use
such equipment. To reduce the risk of accidents or incidents, service on the unit should only be
performed by your local pool Professional.
FAILURE TO FOLLOW INSTRUCTIONS CAN CAUSE SEVERE INJURY AND / OR DEATH.
CAREFUL REMINDERS
•It is recommended that installation of all equipment is complete by a suitably qualified pool
professional who will ensure your products are installed to your local standards / codes to ensure
optimum safety and performance.
•All components of the filtration system including Pumps, Filters, Heaters must be positioned so
to prevent being used asmeans of access to the pool by young children. To reduce risk of injury,
do not permit children to use or climb on this product. Closely supervise children at all times.
•Make sure all wiring connections are clean and that all wiring and electrical equipment is in good
condition. Damaged wiring must be repaired or replaced by a qualified electrician as soon as
damage is discovered
•Do not add chemicals directly to the pool skimmer. Adding undiluted chemicals may damage
pump, heater, etc and void warranty
•Pump suction is hazardous and can cause entrapment, drowning or disembowel bathers
•Do not block or cover any pool/spa suction
•Do not use or operate swimming pools, spas or spa baths if a suction cover is broken, missing or
loose
•Suction covers and inlets must be installed as per Australian Standards guideline and provided
for every pump to avoid suction entrapment

SFG SERIES TOP MOUNT FIBREGLASS MEDIA FILTER INSTALLATION AND OPERATION MANUAL Page 4of 23
2. GENERAL OVERVIEW
Congratulations on your recent purchase of your Oasis Aquatics SFG Top Mount Fibreglass Media
Filter.
Please take a moment to read through the entire manual before installing your new unit.
While every effort has been made to ensure that the information contained in this guide is accurate and
complete, no liability can be accepted for any errors or omissions.
Oasis Aquatics reserves the right to change the specification of the hardware and software described
herein at any time without prior notice.
There are 5 different size models in our range:
SFG24-40
SFG24-50
SFG28-50
SFG31-50
SFG36-50
Link by Clamp Type Valves
Link by Nut Type Valves
It is important that you read through the manual to identify the key areas you need to understand,
particularly the following:
•Health and Safety Concerns
•Installation requirements
•How to operate the major features of the unit
•The importance of maintenance
•If you have a problem, what to trouble shoot before you contact your pool service professional
•Finally, your entitlements under your product warranty.
Oasis Aquatics have developed their product line to provide you with the ultimate experience and are
sure you will be delighted with your purchase.
Please note: This manual has been designed to cater for installation rules and codes in Australia.
Specific rules andregulations for other countries may differ. Please speak with your installer should you
have any questions.
Your filter is high performance and corrosion proof designed with superior flow characteristics that is
easy to operate.
Everything is made simple from installation, operation, to the maintenance of the filter. Your Oasis
Aquatics filter will provide crystal clear, healthy swimming water with minimal maintenance.
Oasis Aquatics highly recommends the use of qualified service technicians to ensure the best
performance as well as the health and safety of your family.
Thank you again for choosing an
Oasis Aquatics SFG Top Mount Fibreglass Media Filter.

SFG SERIES TOP MOUNT FIBREGLASS MEDIA FILTER INSTALLATION AND OPERATION MANUAL Page 5of 23
3. HOW IT WORKS
Your Oasis Aquatics SFG Top Mount Fibreglass Media Filter is designed to use the high-quality
filter elements such as Media or Glass to remove dirt particles from pool water. These elements are
specifically designed for your Oasis Aquatics Media Filter and if looked after will provide you with
years of trouble-free operation.
The pool water which contains dirt particles is pumped through your system to the filter. As pool water
passes through the filter, dirt particles will be caught by the filter element and removed from the water.
The cleaned pool water is returned back to the pool through your piping system. The entire process is
continuous and automatic. It is this process that provides the filtration and removal of organic material
such as dust, dirt and fine particles in your pool water.
After a period oftime, the accumulateddirt in the filter causesa resistance toflow, reducing the pressure
in the tank and will reduce the flow of water through your filtration system. This means it is time to clean
your filter.
A good indication when to clean the filter element is by checking the pressure gauge reading.
Cleaning should be performed when you notice the pressure has increased by 10 PSI or 70 kPa from
when it was clean.
The cleaning procedure should be followed for best results.
YOU MUST ALWAYS TURN YOUR FILTER PUMP OFF BEFORE
CHANGING THE MULTIPORT CONTROL VALVE POSITION.
FAILURE TO DO SO WILL CAUSE ACCELERATED WEAR AND / OR
DAMAGE TO THE VALVE MECHANISM

SFG SERIES TOP MOUNT FIBREGLASS MEDIA FILTER INSTALLATION AND OPERATION MANUAL Page 6of 23
4. INSTALLATION
The filter should be installed as close to the pool as possible but keep a distance of at least 1.5m.
Locate the filter on rigid, level surface, preferably in a dry, shaded, and well-ventilated area.
Prior to installation take into consideration the following conditions:
•Position of suction and return PVC connections
•Access for backwashing operation and servicing, including media replacement
•Protection from sun, rain, splashing etc
•Drainage of filter room
•Ventilation and protection of the full filtration system
•Media is loaded through the top opening of the filter
•The overall weight of the filter once the media is added (some filters will exceed 250kg once
loaded and settlement will occur if the mounting is not of sufficient construction).
Once you are happy that the above has been considered, follow these steps:
1. Place the empty tank in position.
a. Loosen the flange clamp and remove filter control valve (if previously installed).
2. Cover the standpipe with the media fill cover. This will prevent any media from getting into the
pipe and working its way into your pool.
3. Fill the tank with water to the level that covers the laterals, or about 1/2 of the tank height. This
helps protect the laterals from excessive shock by the force of the media when pouring into the
filter.
4. Position a corner of the filter media bag over the tank and carefully pour in correct amount and
grade of filter media. Work slowly and carefully to prevent any media from spilling. Repeat until
you have added the amount of filter media needed for your filter.
5. The filter media surface should be levelled and should come to about the middle of the filter
tank.
6. Remove the media fill cover from the top of the stand pipe ensuring all filter media particles are
removed from the valve mounting surface.
7. Assemble the Multiport Control Valve into the filter tank by placing the O-ring into the groove on
the tank.
8. Lower the Control Valve into the tank neck, taking care that the centre pipe slips into the hole in
the bottom of the valve. Rotate the valve until the inlet is approximately in line with the pump.
9. Place the clamp set around the tank and the valve and tighten just enough so that the valve
may be rotated on tank for final positioning.
10. Carefully screw pressure gauge (with O-ring in place) into tapped hole in valve body. Do not
over-tighten.
11. Connect pump to control valve opening marked PUMP.
12. After connections are made, tighten clamps with screwdriver. Tapping around the clamp with a
rubber mallet or screwdriver handle will help seat the clamp.
13. Make return to pool pipe connection to control valve opening marked RETURN and complete
other necessary plumbing connections, suction lines to pump, waste, etc.
14. Make electrical connections to pump per pump instructions.
15. To prevent water leakage, make sure all pipe connections are tight.
DO NOT OVER TIGHTEN.

SFG SERIES TOP MOUNT FIBREGLASS MEDIA FILTER INSTALLATION AND OPERATION MANUAL Page 7of 23
WARNING
Is it important when connecting the WASTE line that you adhere to any local standards and codes in
relation to the disposal of the waste water. It is also highly recommended to use minimum 40mm (1.5”)
PVC Pipe with the SFG25-40 Filter and minimum 50mm (2.0”) PVC Pipe with all other SFG Filters.
To reduce any pressure and to provide the best clean possible, reduce the distance and amount of
bends used for the WASTE discharge line.
To prevent water leakage, be sure all pipe connections are tight.
Prior to starting the filtration process by turning on the pump, we highly recommend that you read
through the pumpinstruction manual to ensure proper installation and to avoid the risk of electric shock.

SFG SERIES TOP MOUNT FIBREGLASS MEDIA FILTER INSTALLATION AND OPERATION MANUAL Page 8of 23
Start-Up Procedure
1. Make sure the correct amount of filter media is located in the tank and all connections have
been connected and secured.
2. Press downward and rotate the Multiport Control Valve handle to the ‘BACKWASH’ position. To
prevent damage to control valve seal, always depress handle before turning.
3. Start the pump according to the pump instruction manual (be sure all suction and return lines
are open), allowing the filter tank to fill with water.
Once water is flowing steady out the waste line, run the pump for at least 2 minutes. The initial
backwashing of the filter is recommended to remove any impurities or fine particles in the media.
4. Turn the pump off and set the control valve to ‘RINSE’position. Start the pump and operate until
water in sight glass is clear, which will usually take approximately 1 minute. Turn pump off and
set valve to ‘FILTER’ position and restart pump. The filter is now operating in the normal filter
mode, filtering dirt particles from the pool water.
5. Adjust pool suction and return valves to achieve desired flow. Check system and filter for water
leaks and tighten connections, bolts, nuts as required.
6. Take note of the initial pressure gauge reading for future reference. Variation may occur from
pool to pool.
NOTE THE INITIAL PRESSURE GAUGE READING WHEN THE FILTER IS CLEAN.
It will vary from pool to pool depending upon the pump and general piping system.
As the filter removes dirt and impurities from the pool water, the accumulation of dirt in the filter will
cause the pressure to rise and diminish the water flow. When the pressure gauge reading is 10 PSI or
70kPa, higher than the initial "clean" pressure you noted, it is time to backwash the filter (see
BACKWASH function).
NOTE: During the initial clean-up of the pool water, it may be necessary to backwash frequently due to
the unusually heavy initial dirt load in the water.
IMPORTANT: To prevent unnecessary strain on piping system and control valve, always turn off the
pump before changing the operation of the control valve. To prevent damage to the pump and filter and
for proper operation of the system, clean pump strainer (basket) and skimmer basket(s) regularly.

SFG SERIES TOP MOUNT FIBREGLASS MEDIA FILTER INSTALLATION AND OPERATION MANUAL Page 9of 23
5. MULTIPORT CONTROL VALVE FUNCTIONS
The Multiport Control Valve controls the direction of water flow throughout your filter allowing you to
easily filter your swimming pool water and then clean your filter tank. Correct operation of the Multiport
Control Valve will give you healthy, clean water for many years.
1) FILTER
Normal Filtration and Vacuuming
This is the standard position when your filtration system is in normal
operation. The water flows in from your pool and is distributed across the top
of the media bed in the filter. Through pressure this water is pushed down
through the Media allowing debris to be removed from the water and collected
in the media bed. Water is then taken up through the laterals and the centre
stem pipe and returned to the pool, usually via some form of sanitation and/or
heating. The filter position can also be used for manual vacuuming and
cleaning of small debris.
2) BACKWASH
Cleaning filter by reversing the flow
This position is used when the media bed requires cleaning. Use the Pressure
Gauge to indicate when this is required, usually 10 PSI or 70 kPa above
operation of a clean filter. When backwash is selected the water flow is
reversed and goes down the stem pipe and out through the laterals. This lifts
the media bed and allows debris to be taken up the filter and out through the
waste pipe. The sight glass will show the quality of the water and you need
to backwash until this water is clear.
3) WASTE
By-passes filter, used for vacuuming to waste or lowering water
level
The waste position allows you to pump excess water from the pool directly
down the waste pipe. This position is useful after heavy rains where the water
level is too high. Water is directed straight through the Multiport Control Valve
and bypasses the filter, going directly to waste. You can also use this position
to vacuum heavy concentration of debris from the pool.
4) RECIRCULATE
By-passes filter for circulating water to pool
Similar to the Waste setting, recirculate allows the water to bypass the filter
but goes straight back to the pool. This is a useful setting if you have applied
some chemicals that need to be circulated, but not removed by the filter. In
addition, if a leak develops in the filter use recirculate to continue circulating
water until it is fixed. The recirculate setting can also be used to assist with
the re-priming of the filter pump, as bypassing the media bed reduces the
resistance in the pump return circuit.
5) RINSE
Used after backwash to flush dirt from valve
Rinse is a very important setting to use after you have completed the
Backwash cycle. In the rinse setting, water is taken from the pool and
distributed on the media bed. This downward flow settles the media bed after
backwashing and carries any remaining loose dirt through to the waste line.
By using Rinse after Backwashing you will eliminate any debris returning to
the pool water. Rinse until you see clear water in the sight glass and should
take half the time of a Backwash cycle.
6) CLOSED
Shuts off all flow to filter or pool
Closed setting acts like a valve and prevents flow of water through the tank,
particularly useful if doing any maintenance on the filtration system.

SFG SERIES TOP MOUNT FIBREGLASS MEDIA FILTER INSTALLATION AND OPERATION MANUAL Page 10 of 23
6. BACKWASHING
Cleaning your Filter will give you the best quality swimming water that is clean, clear and safe for
swimming. It is highly recommended to clean on a regular basis and to monitor the pressure gauge and
BACKWASH when an increase of 10 PSI or 70 kPa is indicated from your clean filter.
TO PERFORM THE BACKWASH OPERATION, YOU MUST FOLLOWING THESE STEPS:
1. Turn off filter pump
2. Change the position of the Multiport Control Valve handle from FILTER to BACKWASH
3. Turn filter pump back on. The water flow is automatically reversed through the filter so the water
is directed from the bottom of the tank, up through the media, flushing the trapped dirt and debris
out of the waste line
4. Check sight glass. The duration of the backwash operation will depend on how dirty your filter
is. Continuously check the sight glass until the water becomes clear.
5. Turn off filter pump
6. Change the position of the Multiport Control Valve handle from BACKWASH to RINSE
7. Turn filter pump back on. The water flow will now be directed back through the Media bed and
then out through the waste line. This will settle the media bed back for normal operation
8. Check sight glass. Continue until water is running clear
9. Turn off filter pump
10. Change the position of the Multiport Control Valve handle from RINSE to FILTER.
11. Turn on filter pump
WARNING
YOU MUST ALWAYS TURN YOUR FILTER PUMP OFF BEFORE
CHANGING THE MULTIPORT CONTROL VALVE POSITION.
FAILURE TO DO SO WILL CAUSE ACCELERATED WEAR AND/OR
DAMAGE TO THE VALVE MECHANISM
Cleaning the Media Filter by BACKWASHING and RINSING is essential to providing clean, safe and
healthy swimming water. A regular cleaning program is highly recommended especially in commercial
applications, the time between cleans and length of cleaning time will depend on size of pool, bather
load and other environmental conditions. Discuss with your local pool professional to work out a
program that best suits your pool.
WHEN VACUUMING THE POOL
If using your Manual Vacuum System to clean the pool. The following can be used as a guide for
settings on your Multiport Control Valve.
•Light Soil, general clean - set the control valve to FILTER position
•Heavy Soil, specific clean - set the control valve to WASTE position. If using the WASTE
position, ensure that the pool water level is well above your skimmer box level as the water will
be directed down the waste line.

SFG SERIES TOP MOUNT FIBREGLASS MEDIA FILTER INSTALLATION AND OPERATION MANUAL Page 11 of 23
7. WINTERISING
Winterising is preparing your pool for freezing conditions which can potentially damage all pool filtration
equipment due to water expanding when frozen. We highly recommend the following steps when
preparing your filter for winter conditions:
1. Backwash the filter for at least thirty minutes before closing down the pool for winterising. This
will clean the filter bed thoroughly and remove any debris from the system.
2. Drain the filter tank by removing the drain cap at the base of the filter tank. Leave the cap off
during winter.
3. Set the control valve handle between the RINSE and FILTER. This will lift the handle and help
with the draining process by allowing air to enter into the tank.
4. Unscrew the pressure gauge from the control valve and store the gauge indoors.
5. Drain and winterise the filter pump according to the manufacturer’s instructions.
This is an ideal time for any repairs that may be required during the off-season. Most pool professionals
will recommend want is needed before the next pool season.
8. SYSTEM TROUBLESHOOTING
If you suspect for any reason your Oasis Aquatics SFG Top Mount Fibreglass Media Filter
is not performing or running as it should be, here are some handy troubleshooting tips that may
assist you. This table should assist with the majority of problems
WHAT IS THE PROBLEM?
POTENTIAL CAUSE?
Media Entering the Pool
•Media too small and getting through laterals
•Flow rate on filter pump is too high and pushing media
through laterals
•Media bed calcified due to poor water chemistry
•Broken lateral
•Loose centre-pipe
•Too much media in filter pump
•Multiport control valve not correctly in FILTER position
•Too much air in filter
Pool Water is Cloudy due to poor
Filtering
•Media bed is dirty and requires backwashing
•Incorrect media has been installed
•Media bed is too low
•Algae build-up in filter due to poor water chemistry
•Excessive dirt in pool
•Calcified media bed due to poor water chemistry
•Heavy swimmer load
•Flow rate on filter pump is incorrect for filter size and pool size
•Backwashing cycle is too short
•Backwash line is too small restricting water flow

SFG SERIES TOP MOUNT FIBREGLASS MEDIA FILTER INSTALLATION AND OPERATION MANUAL Page 12 of 23
WHAT IS THE PROBLEM?
POTENTIAL CAUSE?
Media coming out of Waste Line
•Flow rate on filter pump is too high and lifting media too high
on backwash
Filter Leaking Water
•Tank cracked
•Drain plug not tight
•Valve to tank o-ring damaged
Multiport Control Valve Leaks
•Handle is not properly located in selected setting
•Valve to tank o-ring damaged
•Valve cover o-ring damaged
•Pressure gauge o-ring damaged
Abnormal Loss of Pool Water
•Leak inside multiport control valve
•Leak from pool or PVC piping
High Pressure Filter
•Filter requires backwashing
•Calcified media bed due to poor water chemistry
•Return lines too small for flow rate of filter pump
Low Pressure in Filter
•Multiport control valve incorrectly set
•Filter pump flow rate is too slow, check speed and other
control valves
•Filter pump has lost prime
Oasis Aquatics highly recommends regular checks and maintenance of your swimming pool
equipment by a qualified pool professional.
This will extend the life of your equipment and give you the best performance.
NOTE: If the recommendation in this manual does not solve your particular problem(s), please contact
your local dealer for service.

SFG SERIES TOP MOUNT FIBREGLASS MEDIA FILTER INSTALLATION AND OPERATION MANUAL Page 13 of 23
9. POOL CHEMISTRY GUIDELINES
To get the best performance out of any of your pool equipment, it is important that you manage your
water chemistry to the ideal swimming levels. This could vary according to your location and Oasis
Aquatics highly recommend that you employ the services of your local pool professional to get your
pool set-up to exactly what is required.
The below chart gives some guidelines to the major water chemistry areas to provide the best
performance and to maximise your equipment life. Should your chemistry fall outside the suggested
ranges, this could be damaging to the equipment and its performance.
IMPORTANT POOL CHEMISTRY LEVELS
RANGE
pH
7.2 to 7.6
Total Alkalinity
100 to 130 ppm
Total Chlorine
1.0 to 3.0 ppm
Stabiliser (Cyanuric Acid)
40 to 70 ppm
Salt / Mineral
Max 5,000 ppm

SFG SERIES TOP MOUNT FIBREGLASS MEDIA FILTER INSTALLATION AND OPERATION MANUAL Page 14 of 23
10. PRO-ACTIVE MAINTENANCE PROGRAM
Like your motor vehicle it is important to maintain a regular service program for your pool equipment to
ensure the best operation and long lasting results.
The below chart provides a guideline to follow to best look after your valuable equipment. Regular
maintenance can identify any potential issues early and save on expensive maintenance at a later date
WHEN?
WHAT ARE YOU LOOKING FOR?
HOW CAN YOU FIX?
Weekly
Check Pressure Gauge
If pressure increases by 10 PSI / 70 kPa,
then BACKWASH and RINSE the filter
as per instructions.
Quarterly
Check around the unit for
leaves/debris or signs of flooding.
Remove any debris that is restricting air
circulation around the filter.
If in a flood prone location, rectify
Check for any Insects or Ants
It is a good practice to use a good quality
surface spray around your equipment.
Make sure all units are turned off and then
spray around all units to eliminate any
insect/ants etc
Check for any leaks
If you notice any water leaking from the
filter or other equipment, check gaskets
first and reseal.
If leaking continues, contact your local
pool professional to assess and rectify
Annually
Compare operating pressure of
backwashed filter to initial pressure
(when new)
If pressure after backwash is more than
40 kPa or 6 PSI different from new filter, a
media change may be required.
Consult with pool professional for advice.

SFG SERIES TOP MOUNT FIBREGLASS MEDIA FILTER INSTALLATION AND OPERATION MANUAL Page 15 of 23
11. SPECIFICATIONS & DIMENSIONS
Model
Valve Port
Size
Filtration
Area
Design
Flow
Height
Diameter
Media
Glass
Fine
Glass
Course
mm
m2
m3/h
A
B
Kgs
kgs
kgs
SFG25-40
40
0.32
15.60
950
635
145
45
60
SFG25-50
50
0.32
16.32
980
635
145
45
60
SFG28-50
50
0.41
20.16
1092
723
200
60
75
SFG32-50
50
0.50
24.90
1200
800
260
75
105
SFG36-50
50
0.64
31.20
1300
900
300
75
150
SFG25-40 / SFG25-50 SFG28-50 / SFG32-50 / SFG36-50
A
A
B
B

SFG SERIES TOP MOUNT FIBREGLASS MEDIA FILTER INSTALLATION AND OPERATION MANUAL Page 16 of 23
12. REPLACEMENT PARTS OF FILTER
SFG25-40
REPLACEMENT PARTS OF FILTER
Item
Part No
Description
Qty
1
8280105
6 Way 1.5" (40mm) Top Mount Valve (Valve Only)
1
2
89280101
1.5" (40mm) union (Black) with sight glass with O-ring
1
3
89280102
1.5" (40mm) union set with O-ring
2
4
06011029
Maximum 40PSI Indication, Stainless Steel Casing
1
4
E190109
Connector for Pressure Gauge/Stopper
1
5
89010119
M6*50 Screws with Nut
2
6
89010101
Clamp Lock
1
7
02011134
O-Ring for Filter Neck
1
8
89010110
SFG25-40 Filter tank
1
9
89010103
SFG25-40 Lateral Assembly with Center Pipe
1
10
01172008
Laterals (126mm) for SFG25-40
8
11
01111062
21-28" Filter Base for SFG25-40
1
12
01181052
Fastener for Filter Base
4
13
89010107
Water Drain Set
1
14
01015006
Media Diverter (Black) for 1.5" (40mm)
1
REPLACEMENT PARTS OF MULTIPORT VALVE
Item
Part No
Description
Qty
1
01013003
Handle (Big)
1
2
03018008
Pin for Handle
1
3
01181001
Washer for Handle
1
4
89280107
M6 x 30 Screw with Nut for Standard Lid
6
5
01013154
1.5" (40mm) Top/Side Mount Valve Standard Lid (Black)
1
6
02011002
O-Ring for 1.5" (40mm) Valve Lid
1
7
01181002
Washer for Spring
1
8
03014001
Spring for 1.5" (40mm) Top/Side Mount Valve
1
9
02011022
O-Ring for Valve Rotor
2
10
01021001
1.5" (40mm) Valve Rotor
1
11
02311002
Spider Gasket
1
12
E190147
1.5" (40mm) Body with Diffuser (Black)
1
13
02011001
O-Ring for Diffuser
1
14
02020013
O-Ring for 1.5"Connector
3
15
01013015
1.5" (40mm) Connector (Black)
3
16
02011003
O-Ring for 1.5" (40mm) Adaptor
3
17
01171153
1.5" (40mm) Union (A/E)
2
18
01013017
1.5" (40mm) Union Nut (Black)
3
19
01041002
1.5" (40mm) Union with Sight Glass (Short)
1
20
01172026
1.5" (40mm) Union with Sight Glass Holder
1
21
89280120
Connector for Pressure Gauge/Stopper
1
22
89021307
Drain Plug with O-ring
1
23
06011029
Oil Pressure Gauge with O-ring
1
24
919305061
MPV01/MPV03 Upper part
1

SFG SERIES TOP MOUNT FIBREGLASS MEDIA FILTER INSTALLATION AND OPERATION MANUAL Page 17 of 23
SFG25-50
REPLACEMENT PARTS OF FILTER
Item
Part No
Description
Qty
1
88281506
MPV08 6-Way 2.0" (50mm) Clamp Type Multiport Valve
1
2
89280103
2.0" (50mm) Union
3
3
06011029
Maximum 40PSI Indication, Stainless Steel Casing
1
3
E190109
Connector for Pressure Gauge/Stopper
1
4
89280104
Sight glass with O-Ring
1
5
03021035
M6 Nut
2
6
03011095
Screw
2
7
01271010
Clamp Lock
2
8
02011134
O-Ring for Filter Neck
1
9
89010110
V650 Filter tank
1
10
89010130
Lateral Assembly with Center Piper
1
11
89010107
Water Drain Set
1
12
01111062
Filter Base
1
13
01181052
Fastener for Filter Base
4
14
01172010
Laterals (185mm)
4
15
89012516
MFV27 MFV31 MFV35 Laterals bracket
4
16
01172007
Laterals(115mm)
4
REPLACEMENT PARTS OF MULTIPORT VALVE
Item
Part No
Description
Qty
1
01013003
Handle (Big)
1
2
03018008
Pin for Handle
1
3
01181027
Washer for Handle
1
4
01181028
Defend Lock
1
5
01020009
2.0" (50mm) Lid
1
6
01181002
Washer for Spring
1
7
02011022
O-Ring for Valve Rotor
2
8
03014014
Spring for Valve
1
9
89280805
2.0" (50mm) Valve Rotor with Spider Gasket
1
10
02010003
O-Ring for Lid
1
11
E190213
2.0" (50mm) Body with Diffuser
1
12
89280120
Drain Plug Fitting with O-ring
1
13
89021307
Drain Plug with O-Ring
1
14
06011029
Oil Pressure Gauge with O-Ring (40Psi)
1
15
02020016
1.5" Union Nut (Black)
6
16
01013031
2.0" (50mm) Connector (Black)
3
17
01171154
2.0" (50mm) Union (A/E)
3
18
01013032
2.0" (50mm) Union Nut (Black)
3
19
89280104
Sight Glass with O-Ring
1
20
02011005
O-Ring for Diffuser
1
21
919301023
MPV08 Upper part
1

SFG SERIES TOP MOUNT FIBREGLASS MEDIA FILTER INSTALLATION AND OPERATION MANUAL Page 18 of 23
SFG28-50, SFG32-50 & SFG36-50
REPLACEMENT PARTS OF FILTER
Item
Part No
Description
Qty
1
89010601
Nut with Washer
12
2
88280306
6 Way 2" Top Mount Valve (Valve Only)
1
3
6011029
Maximum 40PSI Indication, Stainless Steel Casing
1
4
89280103
2" union set with O-ring
3
5
89280104
Sight Glass with O-Ring
1
6
2011126
Filter Neck Gasket
1
7
89010612
SFG28-50 Filter Tank with Base
1
7
89010603
SFG32-50 Filter Tank with Base
1
7
89010604
SFG36-50 Filter Tank with Base
1
8
89010611
SFG28-50 Standpipe with Hub
1
8
89010607
SFG32-50 Standpipe with Hub
1
8
89010608
SFG36-50 Standpipe with Hub
1
9
1172010
Laterals (185mm) For SFG28-50
8
9
1172011
Laterals (233mm) For SFG32-50 & SFG36-50
8
10
89010107
Water Drain Set
1
11
1111062
21 - 28inch Filter Base For SFG28-50
1
11
1112038
32 - 40inch Filter Base For SFG32-50 & SFG36-50
1
REPLACEMENT PARTS OF MULTIPORT VALVE
Item
Part No
Description
Qty
1
1013003
Handle (Big)
1
2
3018008
Pin for Handle
1
3
1181027
Washer for Handle
1
4
E190144
M6 x 33 Screw with Nut
10
5
1013158
50mm Top Mount Valve Standard Lid (Black)
1
6
3014014
Spring for Valve
1
7
2011006
O-Ring for 50mm Top Mount Valve Lid
1
8
2011022
O-Ring for Valve Rotor
2
9
1181002
Washer for Spring
2
10
1021002
50mm Valve Rotor
1
11
2311003
Spider Gasket
1
12
E190220
50mm Body with Diffuser (Black)
1
13
2011005
O-Ring for Diffuser
1
14
2020016
O-Ring for Connector
6
15
1013031
50mm Connector (Black)
3
16
1171154
50mm Union (A/E)
3
17
1013032
50mm Union Nut (Black)
3
18
89280104
Sight Glass with O-Ring
1
19
89280120
Connector for Pressure Gauge/Stopper
1
20
89021307
Drain Plug with O-ring
1
21
6011029
Oil Pressure Gauge with O-ring
1
22
919301014
MPV02 Upper part
1

SFG SERIES TOP MOUNT FIBREGLASS MEDIA FILTER INSTALLATION AND OPERATION MANUAL Page 19 of 23
13. WARRANTY
Australian Consumer Law
Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are
entitled to a replacement or refund for a major failure and for compensation for any other reasonably
foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to
be of acceptable quality and the failure does not amount to a major failure.
Your Oasis Aquatics SFG Top Mount Fibreglass Media Filter is covered by a limited five (5) year
warranty and commences from the date of purchase.
Please refer below for details as follows:
•5 year limited warranty on Oasis Aquatics SFG Top Mount Fibreglass Media Filter unit against
component failure or defects workmanship and materials excluding obvious neglect, misuse,
improper installation or improper maintenance from date of purchase.
•12 months limited warranty on multiport valve, internal components, including o-rings, gaskets and
gauges unit against defects in workmanship and materials excluding obvious neglect, misuse,
improper installation or improper maintenance from date of purchase.
•12 months warranty is provided on installation labour completed by Oasis Aquatics or Sunlover
Heating staff from date of install.
•Items that are replaced as part of routine maintenance are not covered by this warranty.
This warrantyis subject tothe conditions and limitations herein after stated and is applicable to workmanship
and materials only.
You must notify Oasis Aquatics of the failure of any component of your product within seven (7) days of the
recognised fault.
Oasis Aquatics will atits option, repair or replace any defective parts. Component failure must be due solely
to a defect in materials or workmanship. The manufacturer will not be held liable for damage caused by, but
not limited to, corrosion, scaling or stress.
This warranty does not apply if failure is due to any abuse, misuse, improper installation or accident
or to any of the following:
•The customer has not complied with Oasis Aquatics terms and conditions of sale
•The product was used in an application for which it wasn’t intended
•The product was altered, modified or repaired by any other person than Oasis Aquatics or its
Authorised Service Agents
•The product has not been installed, maintained or operated in accordance with installation and
operating instructions
•Environmental influences such as flooding, storm, lighting, fire
•Running filtration system without water
•Damage beyond our control
This Warranty is solely for the benefit of the original consumer and with respect to the original installation
only. and is therefore non transferable under any circumstance.
Oasis Aquatics shall have no liability for incidental or consequential damages. No person is authorized to
make any representation or warranty on behalf of Oasis Aquatics other than what is stated here.
Ifa defectin materialsor workmanship occurswithin thewarrantyperiod Oasis Aquatics will,at itsdiscretion
repair or replace product or the defective part of the product free of charge or cause the product or the
defective part to be repaired or replaced by an Authorised Oasis Aquatics Service Agent free of charge.
Oasis Aquatics reserves the right to substitute defective parts or the product with parts or product of similar
quality, grade and performance where an identical part or product is not available. Parts or products may be
replaced by refurbished goods of the same type rather than be repaired.
If the product is bought as a demonstration, refurbished, ex-rental, discontinued or otherwise previously
unboxed unit, the warranty applicable shall be limited to twelve (12) months only.
On Commercial Installations, such as health clubs, swim schools, motels/hotels and hydrotherapy, parts and
in field labour warranty, the warranty period is limited to twelve (12) months only.