Observint CD80B User manual

Infrared Turret Dome CCD Camera
User Manual
Products: CD80B, CD80W, CD80BHR, CD80WHR,
CD80BVF, CD80WVF, CD80BHRVF, CD80WHRVF
Please read this manual before installing and using this camera and always follow instructions for proper use.
Save this manual for future reference.
CD80_IM
1/10/13

WARNING
!Do not use the camera if fumes, smoke or a strange odor is emitted
from the unit, or if it seems to not function correctly. Disconnect the
power source immediately and consult your supplier.
CAUTION

Always follow the instructions in the installation guide when
applying power. Fire and equipment damage can occur if power
is applied incorrectly. For the correct power supply, refer to the
specication sheet.
CAUTION
Do not install or operate in small, unventilated areas. Heat build up
can signicantly reduce the performance and operating life of the
product and may cause a re.
© 2013 Observint Technologies. All rights reserved.
11000 N. Mopac Expressway, Building 300, Austin, TX 78759
1.800.335.9777 | Fax: [phone]
For Sales/Support, please contact your supplier.
www.observint.com
WARNING
Risk of electric shock – do not open.
To reduce the risk of electric shock, do not
disassemble the camera module. No user
serviceable parts are inside. Refer servicing to
qualied service personnel.

iii
Infrared Turret CCD Camera User Manual
WARNINGS & CAUTIONS
CAUTION
To prevent damage, do not drop the camera or
subject it to strong shock or vibration.
CAUTION

If installed close to a TV, radio transmitter, magnet, electric motor
transformer or audio speakers the magnetic eld generated may
interfere with or distort the image.
CAUTION

Whether or not the camera is used outdoors, never point it toward
the sun. Use caution when operating the camera in the vicinity of spot
lights or other bright lights and light reecting objects.
CAUTION

Do not use the camera in extreme environments where high
temperatures or high humidity exists. Use the camera under
conditions where temperatures are between -4 °F ~ 122 °F
(-20 °C ~ 50 °C), and humidity is below 85%.

iv www.observint.com
TABLE OF CONTENTS
Table of Contents
SECTION 1 Features ................................................. 1
1.1 Camera components ......................................2
1.2 Camera connections ......................................3
SECTION 2 Installation .............................................. 4
2.1 What’s in the box .........................................4
2.2 Tools you need ...........................................4
2.3 Installation instructions ...................................5
SECTION 3 Aiming the Camera ....................................... 11
SECTION 4 Cleaning ................................................ 12
SECTION 5 Specications ........................................... 13
SECTION 6 Troubleshooting ......................................... 14

1
Infrared Turret CCD Camera User Manual
SECTION 1: FEATURES
SECTION 1 Features
The CD80 series weatherproof, vandal resistant turret dome cameras are ideal for outdoor
locations where surveillance in low-light environments is required. These cameras include:
• Advanced image sensors for greater picture clarity
• Precision lenses to achieve the perfect view
• The ability to see in the dark with built-in IR array
• Turret design for increased vandal resistance

2www.observint.com
SECTION 1: FEATURES
1.1 Camera components
Drop Cable
Video 75 Ohm
12 V DC
Base
Bezel
Camera
Housing
Bezel set
screw (2)
Camera
Module
Focus Adjust
(VF Models)
Camera Lens
IR LEDs
Camera assembly

3
Infrared Turret CCD Camera User Manual
SECTION 1: FEATURES
1.2 Camera connections
Connect
Connect
Single camera with monitor (above)
Multiple camera system with DVR and monitor (below)

4www.observint.com
SECTION 2: INSTALLATION
SECTION 2 Installation
2.1 What’s in the box
The camera package contains:
• Camera assembly
• Instruction manual
• Hardware kit, including four 1" screws, four wall inserts and a hex wrench
2.2 Tools you need
To install the camera, you will need:
• Phillips #2 screwdriver
• Small blade screwdriver (for adjusting VF model cameras)
Depending on how the camera is mounted, you may also need:
• Hammer
• Drill with 3/32" and 3/16" drill bits
• 3/4" hole saw

5
Infrared Turret CCD Camera User Manual
SECTION 2: INSTALLATION
2.3 Installation instructions
1. Use the hex wrench provide to loosen the two bezel set screws, then remove the
bezel from the camera assembly.
Bezel set screw
(1 of 2)
Remove the bezel
2. Determine where the camera will be mounted.
3. Using the base as a template, mark the location of the four mounting screw holes.

6www.observint.com
SECTION 2: INSTALLATION
Mounting Screw
Holes
Camera base
4. Drill mounting screw holes into the mounting surface.
a. If the mounting surface is a soft material, such as a drywall, use a 3/16" bit to
drill the mounting holes. Use a hammer to tap the wall inserts provided into
each hole until they are ush with the surface.
OR (continued on next page)

7
Infrared Turret CCD Camera User Manual
SECTION 2: INSTALLATION
b. If the mounting surface is a very soft material, such as ceiling tile, place a wood
block behind the tile. Screws longer than 1" may be required. Drill holes for the
mounting screws through the surface and into the wood block.
OR
c. If mounting the camera on a harder surface, such as wood, drill the mounting
screw holes with a 3/32" bit.
5. Determine the cable routing. If the cable is to be routed through a hole in the
mounting location within the coverage of the base, perform the following steps. If
the cable will be routed through a cable guide in the base, skip to step 9.
Cable guide in base
6. Drill a 3/4" hole through the mounting surface at the center of the base.

8www.observint.com
SECTION 2: INSTALLATION
3/4" Cable
Routing Hole
7. Use a #2 Phillips screwdriver to mount the base with the provided screws.
8. With the camera in the camera housing, route the drop cable through the 3/4" hole
until the camera housing is tted onto the base. Place the housing bezel over the
camera housing and screw it onto the base until the camera and camera housing are
held in place. Skip to step 12.
9. Set the camera on the base with the camera cable pressed into one of the cable
guides of the base. Allow some slack in the cable within the base to allow for camera
positioning later.

9
Infrared Turret CCD Camera User Manual
SECTION 2: INSTALLATION
10. Use a #2 Phillips screwdriver to mount the base with the provided screws.
11. Without allowing the camera to hang by the drop cable, place the camera module
onto the base, cover with the camera housing, then move the bezel into place.
Tighten the two bezel set screws enough to hold the assembly together.
Reassemble camera
12. Attach the BNC video/power cable to the camera cable as required.

10 www.observint.com
SECTION 2: INSTALLATION
CAUTION
Notice that power connectors on the BNC video/power cable are
dierent at each end!
Connect
To DVR/Monitor
and Power
To DVR/monitor
and power
Cable attachment

11
Infrared Turret CCD Camera User Manual
SECTION 3: AIMING THE CAMERA
SECTION 3 Aiming the Camera
1. Connect the video cable from the camera to a test monitor or to the BNC input on the
DVR.
2. Apply 12 Vdc power to the camera.
3. Loosen the bezel set screws until the camera module and housing can be rotated on
the base.
4. While observing the video from the camera, rotate the camera and housing and/or
tilt the camera within the housing to point it at your surveillance target.
5. Tighten the bezel set screws to hold the camera assembly together.
6. If you have a CD80BVF /CD80WVF or CD80BHRVF / CD80WHRVF camera, use a small
blade screwdriver to adjust the focus and zoom if necessary.

12 www.observint.com
SECTION 4: CLEANING
SECTION 4 Cleaning
Clean the camera lens and IR lamp shield with an approved glass cleaning solution and a
lint free cloth.
• Dust can be removed from the unit by wiping it with a soft damp cloth. To remove
stains, gently rub the surface with a soft cloth moistened with a mild detergent
solution, then rinse and dry it with a soft cloth.
• Remove all foreign particles, such as plastic or rubber materials, attached to the
camera housing. These may cause damage to the surface over time.
CAUTION

Do not use benzene, thinner or other chemical products on the camera
assembly; these may dissolve the paint and promote damage of the
surfaces. Before using any chemical product, read the accompanying
instructions carefully.

13
Infrared Turret CCD Camera User Manual
SECTION 5: SPECIFICATIONS
SECTION 5 Specications
Model CD80B /
CD80W
CD80BHR /
CD80WHR
CD80BVF /
CD80WVF
CD80BHRVF /
CD80WHRVF
Image Sensor 1/4" Sharp CCD 1/3” SONY CCD 1/4” Sharp CCD 1/3” SONY CCD
TV system NTSC
CCD total pixels 537 (H) x 505 (V) 811 (H) x 508 (V) 537 (H) x 505 (V) 811 (H) x 508 (V)
Horizontal Resolution,
Scanning system
420 TVLines,
60 elds/s
650 TVL color,
700 TVL B/W
60 elds/s
420 TVL,
60 elds/s
650 TVL color,
700 TVL B/W
60 elds/s
SYNC system Internal
Minimum illumination 0 lux / F2.0 (LED on)
Lens 3.6 mm lens 3.6 mm lens 2.8 - 12 mm 2.8 - 12 mm
IR range (approx.) 65 ft (20 m) 65 ft (20 m) 98 ft (30 m) 98 ft (30 m)
Infrared status < 10 lux by CDS Auto Control
B.L.C. control Auto
White balance Auto
Gain control Auto
Electronic shutter 1/60 ~ 1/120,000 s
S/N ratio > 48 dB
Gamma correction > 0.45
Video output 1.0 Vp-p / 75 Ω
Operating temp. -4 °F ~ 122 °F (-20 °C ~ 50 ° C)
Operating humidity Below 85% RH
Power supply 12 Vdc (±10%) 220 mA
Dimensions 3.7 in (D) x 3.25 in (H) (94 mm (D) x 68.5 mm (H))
Weight-Net 1 lb (450 g) approx.

14 www.observint.com
SECTION 6: TROUBLESHOOTING
SECTION 6 Troubleshooting
Before sending the camera for repair, please check below to make sure that the camera is
installed correctly. If it still does not perform adequately, please consult your supplier.
1. No picture on the monitor screen.
a. Check that all connected devices are powered on.
b. Conrm that the voltage is correct.
c. Conrm that the power supply provides enough current
to power the camera.
d. Check that all video cables are correctly connected.
1. The picture is not clear.
a. Check that your monitor is correctly adjusted.
b. Conrm that the glass in front of the lens is clean.
If there is dust, dirt or ngerprints on the glass, the image
quality will be aected. To clean the glass use a soft, dry
and non-abrasive cloth or a commercially available lens cleaning set.
c. Correctly adjust the focus (VF (varifocal) models only.)

15
Infrared Turret CCD Camera User Manual
SECTION 6: TROUBLESHOOTING
2. The picture has interference.
a. The camera may be close to a high voltage source,
such as a power generator.
b. The BNC cable is not terminated properly.
c. The video cables are not connected properly.
CAUTION

This camera is a precision instrument and when treated with care,
will provide years of satisfactory performance. If a problem does
occur, do not open the camera to make repairs. Servicing should
always be referred to your supplier.

16 www.observint.com