Observint R5VBHS User manual

1www.observint.com RS_R5VBHS_CQ
190429
Installation
Before installation:
• Make sure that the device is in good condition and all the assembly parts are included.
• Check the specication of the products for the installation environment.
• Make sure that the wall or the ceiling is strong enough to withstand 3 times the weight of the camera.
• To avoid re or shock hazard, use only UL listed power supplies. Verify that the power supply will
provide the rated voltage and wattage for the camera. See the Specications section.
Step 1. Mounting the camera
A R5VBHS camera can be mounted directly to a wall or ceiling. The surface should support at least three
times the weight of the camera. The drop cables of this camera are normally routed through mounting
surface, but can be routed through the cable channel.
NOTE
If mounting the camera on a wall, ensure that the cable channel in the mounting base is down.
If mounting the camera on a ceiling, orient the mounting base so that the cable channel is pointing
away from any source of water, dust, and other contaminates.
1. Acquire the kind of fasteners that will work best for mounting the camera to the ceiling or wall. The
mounting hardware provided with the camera will work well withe many types of surfaces.
2. Using the camera or the template provided, mark the locations of the mounting screw holes. If
routing the drop cables through the surface behind the mounting bracket, also mark a 3/4” hole for
the drop cables.
3. Drill holes in the surface of the mounting location to accommodate the camera fasteners and the
drop cables.
4. Route the video and 12 Vdc power extension cables from recorder and power source to the camera
mounting location and out through the hole drilled for the camera drop cables.
5. Connect the video and power extension cables to the camera drop cables. Verify that the power
cable connector polarity matches the polarity of the power drop cable.
WARNING
!Drop cable connectors are not waterproof. Failure of the power or video
drop cable connector due to moisture or another contaminant is considered an
installation error, which voids the warranty. Seal all connectors adequately.
6. Set the HD format select switches on the drop cable for the video encoding you prefer to use. See
the drop cables photo to the left.
7. Route the drop cable through the hole in the mounting surface, then attach the camera assembly to
the surface using the appropriate fasteners.
8. Apply power to the camera through the 12 Vdc power cable.
9. Verify that you can see video from the camera at the recorder.
Step 2. Camera adjustments
1. While observing video from the camera, loosen the mounting bracket pan, tilt and rotation
adjustment lock screws.
2. Point the camera at your surveillance target, and then tighten mounting bracket adjustment screws
to hold the camera in position.
R5VBHS 5MP 100 ft IR 4-in-1 HD Bullet
Camera Quick Installation Guide
This 5.0 MP HD-TVI bullet security camera captures sharp high denition video images with its high-
performance CMOS sensor and 2.8 ~ 12 mm varifocal lens.
Features
• 2592 (H) × 1944 (V) (5 MP) progressive scan CMOS sensor
• 2.8 mm ~ 12 mm varifocal lens providing a 81.04° ~ 28.78° horizontal eld of view
• Full-frame IR up to 100 feet
• Flip, Rotation and Corridor modes image adjustments
• D-WDR, IR cut lter
• IP66 weatherproof rating
Camera body
Light sensor
Lens
Focus adjust
Zoom adjust
Sun shield
Drop cable and cable channel
Adjustable
mounting
bracket
R5VBHS camera assembly
12 Vdc Power
connector
HD Video BNC
connector
HD format
select switches
*To reset the camera, press and hold down the Reset button for ten seconds while the camera is powering on.
Camera drop cables
What’s in the box
• Camera assembly
• Mounting hardware
• L-wrench
• Drill template
• Quick Installation Guide
Tools you need
To install the camera, you will need:
• 12 Vdc power source. See Specications for wattage requirement.
• Tools and additional fasteners (may be required) for mounting the camera
• Phillips #2 screwdriver
• Video and 12 Vdc power extension cables

2www.observint.com
0° ~ 90°
0° ~ 360°
0° ~ 360°
Rotation: Use for horizon
line adjustment
Pan: Use
for pan
adjustment
Tilt: Use for
elevation
adjustment
Mounting bracket adjustment
3. Adjust the focus and zoom as needed. Adjustment screws are located on the face of the camera.
4. Make additional pan, tilt and/or rotation adjustments using the steps above if needed to perfect the
camera eld of view.
5. Tighten the mounting bracket screws to hold the camera body in position.
Specications
Signal System PAL/NTSC
Frame Rate
5AHD / 5TVI: 5 MP @ 20 fps
4AHD / 4CVI / 4TVI: 4 MP/P @ 25 fps, 4 MP/N @ 30 fps
CVBS: 960H “
Resolution 5 MP: 2592(H) × 1944(V)
Min. illumination 0.05 lux @ F1.2 (AGC ON), 0 Lux with IR ON
Shutter Time 1/15 s to 1/50,000 s
IR led 24 pcs
Lens 2.8 ~ 12 mm
Horizontal Field of View 81.04° (wide) ~ 28.78°( tele) (2.8 ~ 12 mm)
3-axis adjustment Pan: 0 ~ 360°, tilt: 0 ~ 90°, rotate: 0 ~ 360°
Day & Night IR cut lter
IR Cut Filter Yes, 850 nm
Synchronization Internal synchronization
D-WDR Supported
Menu
AGC Yes
Day/Night Modes EXT / Auto / Color / BW (black and white)
White balance Auto / Manual
BLC Yes
S/N Ratio 35 dB
OSD Supported
Interface
Video Output Termina-
tion 1 × BNC video output
Switch Buttons TVI / AHD / CVI / CVBS
General
Rating IP66 (waterproof)
Power supply 12 Vdc
Power consumption 4 W max.
IR range Up to 100 ft (30 m)
Communication Up the coax, Protocol
Dimensions Ø9.43 in × 3.41 mm (Ø239.5 × 86.6 mm)
Weight 1.74 lb (790 g) approx.
Cleaning
Clean the camera dome with an approved glass cleaning solution and a lint free cloth.
• Dust can be removed from the unit by wiping it with a soft damp cloth. To remove stains, gently rub
the surface with a soft cloth moistened with a mild detergent solution, then rinse and dry it with a
soft cloth. Do not use benzene, thinner or other chemical products on the camera assembly; these
may dissolve the paint and promote damage of the surfaces.
• Remove all foreign particles, such as plastic or rubber materials, attached to the camera housing.
These may cause damage to the surface over time.
© 2019 Observint Technologies. All rights reserved.