OdinLake ERGO CORE User manual

Ergonomic Chair
Health & Stylish
OdinLake
www.odinlake.com
ODINLAKE ERGO CORE
USER GUIDE
MODEL:（B625-1）
Note: Thanks for purchasing from OdinLake. This manual contains
important information so please keep it for further possible uses. If you
have any questions that can not be solved by this manual, contact us:
[email protected]

02Tips
Warranty Rules 10
03Tools List
07Functions
11Office Ergonomic Guide
12-13Disclaimer
04Parts List
05-06Assembly Instructions
08Frequent Questions Answers
09Frequent Assembling Malfunction
Contents

Tips
1. Please make sure that all bolts and screws have been tightened
properly before actually using the chair. Check all levers, adjust knobs
and buttons before everyday use.
P.S: If the cylinder doesn't match the seat plate appropriately, the
height adjuster may stop functioning.
2. Please inspect the chair twice a year. Daily use can wear down the
screws and bolts, so regular inspections are important in order to keep
you safe.
3. No standing on the chair.
4. Please do not press the height adjuster down while adjusting, you
only have to lift it slightly to raise or lower the seat. Hard pushing
might break the adjuster.
5.If you are giving this chair to a third person/party, please attach this
manual with the chair.
6. Installation tips: follow the instructions carefully. Please do not
tighten the screws until all screws are lined up at once. This helps you
make changes easier if some steps go wrong. Over-tightening one
screw can make other screws hard to tighten.
7. Please tighten all screws again after the set-up process is complete.
Tools List
Ax5
Casters
Bx1
Base
Cx1
Cylinder
Dx1
Backrest
Ex1
Seat
Fx2
Armrests
Gx1
Seat Plate
Hx7
Bolts
M6*45mm
Ix5
Bolts
M6*35mm
Jx11
Lock Washers
Φ6*16mm
Kx5
Bolts
M8*20mm
* Each type of bolt and washer has one extra as a spare.
Lx5
Lock Washers
Φ8*16mm
Mx1
Allen Wrench
02 03
Parts List
Tools List

D
F
E
GC
B
A
Parts List
ITEM
A
B
C
D
E
F
G
DESCRIPTION
Casters x5
x1
x1
x1
x1
x2
x1
Base
Cylinder
Backrest
Seat
Armrests
Seat Plate
QUANTITY
Assembly Instructions
Step 1
Take the Casters(A) and push
them into the 5-star Base(B).
Install the Cylinder(C) into
the Base(B).
C
B
A
Step 2
Fix the Armrests(F) to the
Seat(E) with 6pcs Lock
Washers(J) & BoIts(H).
Step 3
Fix the Seat PIate(G) to the Seat(E)
with 4pcs Lock Washers(J) & BoIts(I).
Step 4
Fix the Backrest(D) to the Seat
PIate(G) with 4pcs Lock
Washers(L) & BoIts(K).
04 05
IJ
G
E
F
JH
LKD

ERGONOMIC DESIGN
Curved design offers adequate mid-back and adjustable lumbar support,
which can effectively reduce the pain and pressure of the neck and back
caused by long time sitting.
STYLISH ARMRESTS
The stylish PP+PU material 3D armrests can be multi-functionally adjusted, the
armrest can be adjusted up and down, and the armrest pad can be adjusted forward
and backward + rotated left and right, making the chair more modern and less
monotonous.
ADJUSTABLE HEIGHT
Pull up the adjustment lever then you can raise or lower the seat.
ROCKING FUNCTION
Switch the tilt lock lever to start rocking or lock at certain position. The tension knob
(under the seat) can adjust the tilt tension of the backrest.
Assembly Instructions
Completed!
Step 6
Place the upper part onto the
cylinder
Step 5
Scan the code to watch the
installation video.
Functions
Adjustable Seat Height
Swiveling and Lifting
Tilt Lock
Adjustable Rocking
Tension
06 07