OEM Tools 24893 Service manual

UNPACKING
After unpacking the unit, inspect carefully for any damage that
may have occurred during transit. Check for loose, missing,
or damaged parts. If any damage is observed, a shipping
damage claim must be filed with the carrier. DO NOT use the
OEMTOOLS™24"/30" Outdoor Oscillating Wall Mount Fan if
broken, bent, cracked or damaged parts (including labels) are
noted. Any Outdoor Wall Mount Fan that appears damaged in
any way, operates abnormally or is missing parts should be
removed from service immediately. If you suspect that the
Outdoor Wall Mount Fan was subjected to shock load (a load
that was dropped suddenly, unexpectedly, etc.), immediately
discontinue use until it has been checked by a factory
authorized service center.
Please read and save these instructions. Read through this owner’s manual carefully before using product. Protect yourself
and others by observing all safety information, warnings, and cautions. Failure to comply with instructions could result in
personal injury and/or damage to product or property. Please retain instructions for future reference.
Operating Instructions and Parts Manual 24893 / 24894
9/17
2017 OEMTOOLS™
FOR CUSTOMER SERVICE
Technical Question?
CALL 1-866-458-2472
[email protected]
24"/30" OUTDOOR OSCILLATING
WALL MOUNT FAN
Thank you very much for choosing an OEMTOOLS™Product!
For future reference, please register your new tool at www.oem-tools.com and complete the owner’s record below:
Model: _______________ Purchase Date: ___________
Save the receipt, warranty and these instructions. It is important that you read the entire manual to become familiar with this product
before you begin using it. This product is designed for certain applications only. OEMTOOLS™cannot be responsible for issues arising
from modification. We strongly recommend this product is not modified and/or used for any application other than that for which it was
designed. If you have any questions relative to a particular application, DO NOT use the product until you have first contacted customer
service to determine if it can or should be performed on the product.
The following safety information is provided as a guideline to help you operate your Outdoor Wall Mount Fan under the safest possible conditions.
Any tool or piece of equipment can be potentially dangerous to use when safety or safe handling instructions are not known or not followed.
The following safety instructions are to provide the user with the information necessary for safe use and operation. Please read and retain these
instructions for the continued safe use of your Outdoor Wall Mount Fan. Failure to follow instructions listed below may result in serious injury. In
addition, make sure that anyone who uses the equipment understands and follows these safety instructions as well.
WARNING
Explanation of Safety Signal Words
WARNING: Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.
CAUTION: Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury.
CAUTION: Used without the safety alert symbol indicates a potentially hazardous situation which, if not avoided, may
result in property damage.
NOTES: Provide clarity and helpful information.
24893 - 24"
24894 - 30"

2
Operating Instructions and Parts Manual 24893 / 24894
9/17
2017 OEMTOOLS™
24"/30" OUTDOOR OSCILLATING
WALL MOUNT FAN
IMPORTANT INSTRUCTIONS
AND SAFETY RULES
1. Know your product. Read this manual
carefully. Learn the product’s applications
and limitations as well as potential hazards
specific to it.
2. Keep work area clean and well lit. Cluttered
or dark work areas invite accidents.
3. Keep children away. All children should be
kept away from the work area. Never let a
child handle tools or equipment without strict
adult supervision.
4. DO NOT operate this product if under the
influence of alcohol or drugs. Read warning
labels on prescriptions to determine if your
judgment or reflexes are impaired while
taking drugs. If there is any doubt, DO NOT
attempt to operate.
5. Use safety equipment. Eye protection should
be worn at all times when operating this
tool. Use ANSI approved safety glasses.
Everyday eyeglasses are NOT safety glasses.
Dust mask, non-skid safety shoes, hard
hat or hearing protection should be used in
appropriate conditions.
6. Wear proper apparel. Loose clothing,
gloves, neck-ties, rings, bracelets or other
jewelry may present a potential hazard when
operating this product. Keep all apparel clear
of the product.
7. DO NOT overreach. Keep proper footing
and balance at all times when operating
this product.
8. Check for damage. Check equipment
regularly. If part of the product is damaged,
it should be carefully inspected to make
sure that it can perform its intended function
correctly. If in doubt, discontinue use of
product.
9. Keep away from flammables. DO NOT
attempt to operate this product near
flammable materials or combustibles. Failure
to comply may cause serious injury or death.
10. Store this product out of the reach of children
and untrained persons. This product may be
dangerous in the hands of untrained users.
11. Keep this product dry and clean.
12. Use only accessories that are recommended
by the manufacturer for your model.
Accessories that may be suitable for one
product may become hazardous when used
on another product.
13. Service must be performed only by qualified
repair personnel. Service or maintenance
performed by unqualified personnel could
result in a risk of injury.
14. When servicing a product, use only identical
replacement parts. Use of unauthorized parts
or failure to follow maintenance instructions
may create a risk of injury.
15. Maintain a safe working environment. Keep
the work area well lit. Make sure there is
adequate surrounding workspace. Keep the
work area free of obstructions, grease, oil,
trash, and other debris. DO NOT use this
product in a damp or wet location.
16. Maintain labels and nameplates on this
product. These carry important information.
If unreadable or missing, contact
OEMTOOLS™ for a replacement.
17. Keep this product dry, clean, and free from
brake fluid, oil, and grease.
18. Avoid accidental fire. DO NOT smoke near
this product.
19. The warnings, precautions, and instructions
discussed in this manual cannot cover all
possible conditions and situations that may
occur. The operator must understand that
common sense and caution are factors which
cannot be built into this product, but must be
supplied by the operator.
20. We believe the information contained herein
to be reliable. However, general technical
information is given by us without charge
and the user shall employ such information
at their own discretion and risk. We assume
no responsibility for results or damages
incurred from the use of such information in
whole or in part.
21. The manufacturer declines any and all
responsibility for property damage or injury
if said damage is the result of unskillful
handling by the operator or of failure to
observe the basic safety rules set forth in the
instruction manual.

3
Operating Instructions and Parts Manual 24893 / 24894
9/17
2017 OEMTOOLS™
24"/30" OUTDOOR OSCILLATING
WALL MOUNT FAN
22. The procedures documented in this manual
are to serve as guidelines for the use of this
equipment.
23. The use of this equipment is simple and
straightforward if you follow the instructions.
When operating this equipment, use common
sense, and only use this equipment for its
intended purpose.
PRODUCT DESCRIPTION
The OEMTOOLS™24"/30" Outdoor Oscillating
Wall Mount Fan features a water-resistant motor
for circulating air in workshops, garages and
other structures, where the fan may be subjected
to splashing water or very light rain.
PRODUCT SPECIFICATIONS 24" 30"
Weight 31.3 Lbs. 32.9 Lbs.
Speeds 3
Output Power 1/7 HP
Voltage 120V / 60Hz
Current 2.0A
CFM 6800 7200
RPM 1080
Sound Pressure Level (dB) 74 76
Ingress Protection
(IP) Rating IP44
UL Listed E302275
CONTENTS
(1) 24" Outdoor Oscillating Fan, (1) Wall Mount
Assembly, Mounting Hardware, (1) Instruction
Manual
SPECIFIC SAFETY INSTRUCTIONS
AND WARNINGS
WARNING:Thoroughly read and understand the
provided product manual before attempting to
use this product.
WARNING: DO NOT attempt to disassemble,
repair or modify this fan.
WARNING: DO NOT insert your hand or other
objects into the fan guard or near moving parts.
WARNING: DO NOT submerge this fan in liquids.
WARNING: DO NOT touch this fan with wet
hands.
WARNING: DO NOT use this fan if the cord or
plug has been damaged.
WARNING: Ensure the wall mount is fastened to
a concrete wall or stud capable of supporting the
weight of the fan.
WARNING: Fit the front and rear guards to the fan
prior to attempting to start the fan.
1. DO NOT unplug this fan by holding the cord.
Unplug this fan by holding the plug.
2. DO NOT plug this fan into an extension cord.
3. DO NOT operate near an open flame or
heat source.
4. DO NOT use this fan in conjunction with a
solid-state speed control device.
5. DO NOT leave this fan plugged in while
unattended. Always unplug the fan when
not in use.
6. DO NOT move or attempt to perform
maintenance while this fan is plugged in.
ASSEMBLY INSTRUCTIONS
NOTE: Remove all contents from the box and
reference the parts list to ensure that all parts are
present.
1. Wall installation.
WARNING: DO NOT mount on dry wall.
CONCRETE WALL INSTALLATION
a) Mark the desired hole location using
the Wall Mounting Bracket, then drill the
holes.
b) After drilling, insert the wall anchors and
tap them until flush with wall face.
c) Position the Wall Mounting Bracket and
screw the 3 bolts into the anchors. Tighten
the bolts securely.

4
Operating Instructions and Parts Manual 24893 / 24894
9/17
2017 OEMTOOLS™
24"/30" OUTDOOR OSCILLATING
WALL MOUNT FAN
WALL STUD INSTALLATION
a) Mark the desired hole location using the
Wall Mounting Bracket, then drill small
diameter pilot holes.
b) Position the Wall Mounting Bracket over
the pilot holes and screw the 3 bolts into
the stud. Tighten the bolts securely.
2. Connect the Swivel Adapter to the Mounting
Bracket using the M12x120 bolt, flat washer,
locking washer, nut and rivet assembly
(applied in that order).
3. Place a Fixed Adapter on both sides of the
motor base extension. The Adapters should
taper at the center leaving a small gap.
Fasten securely using the provided hardware.
4. Remove all four sets of hexagonal nuts,
spring washers and bowl washers from
the Motor.
5. Position the Rear Guard over the Motor and
secure using the hexagonal nuts, spring
washers and bowl washers removed in Step 4.
6. Fasten the Fan Blade to the Motor Shaft by
tightening the two fan blade screws. Ensure
the screws are securely tightened.
WARNING: Fully assemble the front guard to the
fan prior to attempting to start the fan. If the fan
blade is loose, the blade may become displaced
from the motor shaft causing product malfunction,
property damage and personal injury.
Assemble the rear grill.
Assemble the blade.
Assemble the front grill.
Assemble the rear grill.
Assemble the blade.
Assemble the front grill.
Assemble the rear grill.
Assemble the blade.
Assemble the front grill.
Assemble the rear grill.
Assemble the blade.
Assemble the front grill.

5
Operating Instructions and Parts Manual 24893 / 24894
9/17
2017 OEMTOOLS™
24"/30" OUTDOOR OSCILLATING
WALL MOUNT FAN
7. Place the Front Guard over the Rear Guard.
Fasten together using the clips along the rim
of the Front Guard.
8. Secure the Guard Assembly by fastening the
retaining bolt, lock washers and nut.
9. Attach the completed Fan Assembly (Step 8)
to the Bracket and Swivel Adapter Assembly
(Step 2) using the provided bolt and nut
assembly. Fasten the Handwheel with Bolt
into the lower square hole.
10. Attach the Motor to a heavy fixed object
(capable of supporting the weight of the fan)
using the safety cable and provided U-bolts.
If the fan dislodges from the mounting
bracket for any reason, the safety cable will
prevent the fan from falling.
NOTE: Ensure the cable does not inhibit the
oscillating range of motion. This can lead to
product malfunction.
ADJUSTING FAN ANGLE
1. While supporting the weight of the fan,
loosen the Handwheel and remove the bolt.
If the weight of the fan is not supported, the
fan will not fall to the ground; however, pivot
uncontrollably toward the operator.
2. Allow the fan to pivot forward to the second
angled adjustment, and replace the bolt and
fasten securely using the Handwheel.
OPERATION INSTRUCTIONS
1. Mount in accordance with provided assembly
instructions.
2. Plug the fan into a grounded 120V / 60 Hz outlet.
3. Test GFCI (Ground Fault Circuit Interrupter) before
each use.
a. Press the RESET button (b). Indicator (a) should
turn red.
b. Press the TEST button (c). Indicator (a) should
turn off.
c. Press the RESET button (b) again before
attempting to use.
d. DO NOT ATTEMPT TO USE IF GFCI TEST
FAILS. Call customer service for assistance.
7. assemble the fan headtothe mounted
.
7. assemble the fan headtothe mounted
.

6
Operating Instructions and Parts Manual 24893 / 24894
9/17
2017 OEMTOOLS™
24"/30" OUTDOOR OSCILLATING
WALL MOUNT FAN
4. Adjust to the desired speed by pulling the
chain (e):
0 – OFF
1 – Low
2 – Medium
3 – High
NOTE: To extend the life of the fan motor, allow
the fan to run for at least one minute at each
setting before moving to the next setting.
5. Press the oscillation knob (d) for oscillating
function. Pull the oscillation knob (d) to lock the
fan to the desired position.
6. Turn the fan to OFF before unplugging from the
electrical outlet.
STORAGE
Store the Outdoor Oscillating Fan in an upright
position and in a clean, dry area. DO NOT store
near flammable items or open flames.
PRODUCT MAINTENANCE
WARNING: Unplug the fan before performing
product maintenance.
WARNING: DO NOT use water to clean the
fan motor. While the product is water resistant,
excessive water may lead to product malfunction.
Use a vacuum cleaner to remove dust from
the protective fan guard and blades. If desired,
remove the front protective fan guard to access
the fan blades. Ensure the protective guard is
securely reattached prior to use.
A damp cloth may be used to wipe the Front
Guard.
DISPOSAL
At the end of the useful life of the OEMTOOLS™
24"/30" Outdoor Oscillating Wall Mount Fan,
dispose of the components in accordance with all
federal, state and local regulations.

7
Operating Instructions and Parts Manual 24893 / 24894
9/17
2017 OEMTOOLS™
24"/30" OUTDOOR OSCILLATING
WALL MOUNT FAN
Item Description Quantity
A Wall Mounting Bracket 1
B Wall Mounting Hardware* 1
CSwivel Adapter 1
DFixed Adapter 2
EFixed Adapter Hardware* 1
FSwivel Adapter Hardware* 1
G Motor 1
H Rear Guard 1
I Fan Blade 1
J Front Guard 1
K Guard Retaining Bolt* 1
L Safety Cable* 1
PARTS DESCRIPTION
PRODUCT LAYOUT
* Not Pictured
G
D
H
C
A
J
I

8
Operating Instructions and Parts Manual 24893 / 24894
9/17
2017 OEMTOOLS™
24"/30" OUTDOOR OSCILLATING
WALL MOUNT FAN
OEMTOOLS™90 DAY LIMITED WARRANTY
For 90 days from the original purchase of this product, OEMTOOLS™will warranty this item. If you find
any defect in material or workmanship, through normal usage, return it to the place of purchase or
to OEMTOOLS™for repair or replacement at our discretion. In order to obtain this service, send your
tool and proof of purchase, transportation pre-paid, to OEMTOOLS™Q.A. Dept., 3850 Raines Road
#3, Memphis, TN 38118. We will not be responsible for lost or damaged goods during transportation;
please insure your package. If our inspection verifies the defect, we will either repair or replace the
product at our election, or we may elect to refund the purchase price if we cannot readily and quickly
provide you with a replacement. We will return repaired products at our expense, but if we determine
there is no defect, or that the defect resulted from causes not within the scope of our warranty, then
you must bear the cost of returning the product.
OEMTOOLS™does not provide warranty for products labeled other than OEM®or OEMTOOLS™.
OEMTOOLS™will not provide any warranty for products subjected to abnormal use. Abnormal use
includes, but is not limited to, abuse, accident, alteration, neglect, and unauthorized or unreasonable
use or repairs. This warranty does not cover bits, blades, files, batteries, or calibration. We recommend
that you maintain your tools and sharpen or replace blades, bits, files, and batteries as necessary.
OEMTOOLS™reserves the right to make any changes in construction or design at any time without
any obligation in incorporating such changes to tools or equipment previously sold.
OEMTOOLS™makes every effort to ensure that its products meet high quality and durability
standards, and warrants to the original purchaser that this product is free from defects in materials
and workmanship for the period of 90 days from the date of purchase. This warranty does not apply
to damage due directly or indirectly to misuse, abuse, negligence or accidents, repairs or alterations
outside our facilities, criminal activity, improper installation, normal wear and tear or to lack of
maintenance.
We shall in no event be liable for death, injuries to persons or property, or for incidental, contingent,
special or consequential damages arising from the use of our product. Some states do not allow the
exclusion or limitation of incidental or consequential damages, so the above limitation of exclusion
may not apply to you. THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES,
EXPRESS OR IMPLIED, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS. This
warranty gives you specific legal rights, and you may also have other rights, which vary from state to
state.
Don’t forget to register your new OEMTOOLS™product at www.oem-tools.com.
CONTACT US
3580 E. Raines Road, Suite 3, Memphis, TN 38118
Tel: [phone]
www.oem-tools.com