Ofna Racing CD-3 SPORT RTR User manual

CD-3 SPORT RTR and PRO RTR
ASSEMBLY INSTRUCTIONS

Diff Oil -
Silicone
REQUIRED FOR OPERATION
THINGS NEEDED
AA Batteries ( 12 pcs )
Glow Fuel
20%
TOOLS NOT INCLUDED IN KIT,
BUT NEEDED TO MAINTAIN YOUR CAR.
Phillips Type Screw Drivers ( L )
Phillips Type Screw Drivers ( S )
Needle Nose Pliers
Cutter
Curved Scissors
Knife
Instant Cement
Cross Wrench
#17109 $3.95
Glow Plug & 17MM Cross Wrench
#10801 $6.95
You need to get batteries for the radio transmitter and the car receiver
packs.
• Radio TX needs (8) eight AA batteries.
• Car needs (4) four AA Ni-cad batteries, Alkaline type batteries will
work, but braking will be reduced. The best is to use a 5 cell hump
pack for increased voltage..
Recommended Option:
You may want to upgrade the car battery pack to a Ni-Cad or NiHm 5
cell type(600AE). This will give more run time. OFNA #10212
#10212 NiHm Hump Pack,
see charger 10214.
10214
Over-nite
Charger
You will need to buy a few items to start the engine and run the car.
• Use 20% nitro CAR fuel. Do not use airplane or helli fuels, they will
over heat engine.
• Buy SHORT glow plugs, OFNA/PICCO Plu (#51007 or 51008) are
long therefore use two copper washers. Use plugs without idle bar.
Always use two copper washers with Picco glow plugs.
In your box you will find..
• #10163 - 250cc Fuel Bottle
• #10219 - Red “D” size glow heater
These parts change depending on stock!

MUST READ THIS BEFORE RUNNING
Running a nitro kit is fun and easy, but to make this a safe rusting.
• Clean oil and dirt from chassis with a degreaser.
and good experience you must observe a few rules. This
kit is extremely fast, easily over 40MPH, and can seriously Precautions
injure someone if you are not careful. • This kit is not a toy. Always run car with a second
person as a spotter and pitman.
Where to run car?
• Any running area you choose must be dry. Do not run • Hot Parts - The pipe, manifold, engine and head are very
car near any water or wet dirt. hot and will cause burns.
• Do not run on public streets. It is very easy to have the
car run over or damaged by hitting the curb. • Rotating Parts - Keep hands away from the drive train,
• Do not operate car in tight confined places. The car is wheels, and engine when engine is running.
very fast and will easily hit something.
• Do not run near people or animals. • Radio - Check batteries life before running the car. If
radio does not have full control of the car with steering
• Due noise, you will want to consider the surrounding and/or throttle/brake do not run until corrected. Failure to
area when operating the car. correct this will result in possible injury and damage to the
• Do not operate the car at night. You will not be able to car or property.
drive it without hitting something.
• Do not operate the car indoors. Engine exhaust is not • Glow fuel - Do leave the glow fuel unattended with the lid
healthy. off. Fuel contains Methanol and Nitro Methane and is
flammable and poisonous.
Glow Fuel
• Glow fuel is poisonous! Store fuel in cool ventilated location. Refer the glow fuel
• Glow fuel is flammable!
• Do not leave in fuel bottle with lid off at any time. label for additional precautions.
• Do not use any fuel other than glow fuel in this engine.
• Car Fuel tank - Never store fuel in car tank, it will ruin the
First Time Starting the Engine engine if left in tank.
Caution! When starting engine make sure the following is
observed. • Always turn off the car BEFORE turning off radio.
• Set engine Master needle to 3 turns (rich setting)
• Do not do this alone, get an experienced friend to help at • DAMAGE DUE CAR RUN AWAY IS NOT A WARRANTY
first. ISSUE.
• Fill fuel tank, try not to spill fuel. Do not spill fuel on
receiver IF YOU DO NOT BREAK-IN ENGINE
• Hold car off the ground, so it will not runaway when first CORRECTLY, MAINLY AT LOW RPM,
starts
• Turn on Radio and check the linkage before starting YOU WILL BREAK THE CONNECTING
engine. ROD!
• Turn on car receiver battery switch.
• Always have an air filter on the carburetor to keep dirt
out. FAILURE TO NOT READ AND
Engine Break-in FOLLOW BREAK-IN ENGINE
• See Engine Page.
Emergency Stopping Engine When Running INSTRUCTIONS WILL VOID
• Remove air filter and cover carb. intake.
• Squeeze fuel line and hold until engine stops. WARRANTY!
• With a rag, cover exhaust outlet.
Storing Car After Running CHECK RADIO SETTING AND
• Remove fuel from tank and fuel lines
• Turn off radio in car LINKAGE BEFORE STARTING
• Put a few drops of after run in engine to keep it from
The car is very fast
and will too easily hit someone.

ASSEMBLY OF THE DIFFERENTIAL
(Build two differentials for front and rear.)
2.5mm
E-Ring
5x8x1.5mm
O-Ring
5x10mm
Washer
Diff.Gear
(small)
Diff.Gear
(Large))
10x15x4mm
Bearing
3x17.8mm
Pin
Flat Head
Screw
M2x7mm
Put the grease
into the diff.
case before
assembly.
10x15x4mm
Ball Bearing
Diff.Case
2.5mm
E-Ring
38256
38252
38253
37450
37771 5x10mm
10T Diff.Gear
10T Diff.Gear
(small)
(small)
13T
Diff.Gear
Step 1
Step 3 Step 4
Step 2
3x17.8mm
Pin
38287
Diff.Gasket
Flat Head
Screw
M2x7mm
Cap Joint
Cap Joint
10x15x4mm
Ball Bearing
2.5mm
E-Ring
5x8x1.5mm
O-Ring
5x8x1.5mm
O-Ring
38278
38255
38255
38257
37450
5x10mm
Washer
13T
Diff.Gear(Large)
Large
Bevel Gear
94052 38278 38256 37771 37450 38253
37771
38278
38256
94052
90020 38632
38632 90020
90020
38632
Washer

M3X12mm
M3X12mm
Screw
Screw
For Front
For Rear
2.6x10mm
Hex Screw
2.6x10mm
Hex Screw
2.6x10mm
Hex Screw
Gear Case
Gear Case
38251
38251
ASSEMBLY OF THE FRONT GEAR BOX
(Builds a gear box for the front.)
* The picture shown is the gear box after
assembly.
* It is normal for the gears to make a noise.
After brake-in, the noise will be reduced.
* Note: Do not over tighten the
2.6x10mm hex screw as it
may cause damage to the
hole in plastic.
94050
94004
94004 94050
ASSEMBLY OF THE GEAR BOX
(Build two gear box for front and rear.)
2.5mm
E-Ring
2.5mm
E-Ring
38258
38526
38519
37400
38251
5x8x0.8mm
Washer
37430
5x11x4mm
5x11x4mm
Ball Bearing
Ball Bearing
M3x4mm
Screw
38530
Steel Ring
(For Front Plastic
Cap Joint)
2x8.8mm
Pin
Gear case 16T Bevel Gear
(small)
38258
16T Bevel Gear
(small)
Bevel Gear
Shaft (small)
38526
Bevel Gear
Shaft (small)
Bevel Gear
Cap Joint (F)
*Adjust the backlash
with the shim*
* Put the gear in the
right position.
* For the good gear mesh,
put the 5x8x0.8 washer
between L-06 and E-43.
Note: Follow the instruction
to put the correct shim
in the right place.
38254
12x15x0.25mm
Shim
37340
5x11x4mm
Ball Bearing
¡¯CHECKI NGYOURDI FF ERENTI ALASSEMBLY
To test the effectiveness of the gear
differential, hold the gear tightly with one
hand and turn one cap joint.
Does the other cap joint move in the
opposite direction and smoothly?
If gear differential does not move smoothly,
assemble the gear diff. once again.
38519
Bevel Gear
Cap Joint (R)
37430
94001
38633
90020
90020

ASSEMBLY OF 2-SPEED CLUTCH TRIGGER DISC
SCREW AS SHOWN,
LEVEL WITH HOLE EDGE
SCREW AS SHOWN,
LEVEL WITH HOLE EDGE
SET BALL TO REST ON CAM, NOT PUSHING. IF
TOO TIGHT, THE BALL WILL PUSH ON CAM
SPREADING SHOE DISC AND WILL NOT FIT
INTO ALUM. CLUTCH BELL #38296
CARE MUST BE TAKEN TO BUILD
THIS ASSEMBLY CORRECTLY,
OTHERWISE 2-SPEED WILL NOT
ADJUST AND MAY NOT WORK AT ALL.
IN FACT, IF 2-SPEED DOES NOT
SHIFT, CHECK OUT THIS ASSEMBLY!.
38525
38316
38313
38313
38313
38312
38312
38315
38315
ASSEMBLY OF THE TWO SPEED CLUTCH SHOES
4x4mm
Set Screw 3x3mm
Set Screw
3x3mm
Set Screw
3x3mm
Set Screw
4x4mm
Set Screw
Clutch Shoe
Carrier
2 Speed Main Shaft
(Cd3 only)
Spring
Spring
Spring
M2x10mm
Hex Screw
M2x10mm
Hex Screw
M2x10mm
Hex Screw
Steel Ball
Steell Ball
2 Speed
Clutch Shoe
2 Speed
Clutch Shoe
* Slide the Clutch Shoe Carrier
over the 38525 and set the
4x4 screw in the "D" cut.
Step 2
Step 1
35325
94033
35325
94034
94033
94034
94033

37430
37430
38519
38519
38279
38279
40042
38519
37400
37400
M3x4mm
M3x4mm
Screw
screw
2x8.8mm
2x8.8mm
Pin
Pin
3x13.8mm
Pin
Pin
38279
M3x4mm
screw 2x8.8mm
Pin 3x13.8mm
Pin
37430
5x11x4mm
Ball Bearing
5x11x4mm
5x11x4mm
6x18.5x4mm
Bevel Gear
Ball Bearing
Ball Bearing
Plastic Washer
Cap Joint(R)
Brake Disk
Brake Disc
Mount
* Put the brake disk
before assembly
*Insert the 38279 into Break
disc mount.
ASSEMBLY OF THE TWO SPEED GEAR
38T
38300
38295
38296
38297
Spur Gear
38301
Spur Gear 1 st Gear Carrier
(One-Way)
2nd Gear
Clutch Bell
(Ball Bearing)
Retaining Ring
Retaining Ring
* Trim any burrs from the
inside of the edge with
a hobby knife before
assembly.
Step 1
Step 2
ASSEMBLY OF THE BRAKE AND DIFF. MOUNT
M3x12mm
M3x30mm
Screw
Screw M2x8mm
Hex Screw
Brake
Spring
Remove the double-side
tape before assembly.
M3x12mm
M3x30mm
M3x30mm
Screw
Screw
Screw
M2x8mm
Hex Screw
38519
38519
38273
38520
38520
38520
40040
Plastic Bushing
Brake Cam
Blake Pad
Spring
Brake Mount
(Upper)(Front)
Roll Bar
Brake Mount
(Upper)(Rear)
* Position the brake cam
in the direction as shown.
Please notice!
* Leave the 1.5mm space
between brake pads.
1.5mm
Bushing Support
Brake Pad
Linings
Brake Pad
3x13.8mm
38297
94001
94001
37400
94001
38272
38271
94004
94047
94004
94047
40040
94000
94000
94000

*"L" make are for
left-side.
ASSEMBLY OF THE FRONT KNUCKLE ARMS AND CVD SHAFT
10mm Alum.
Set Screw
10mm Alum.
Set Screw
10mm Alum.
Set Screw
Front Knuckle
Arm (Left)
Front Knuckle
Arm (Right)
5x11x4mm
Ball Bearing
5x11x4mm
Ball Bearing
5x11x4mm
Ball Bearing
10x15x4mm
Ball Bearing
10x15x4mm
Ball Bearing
8mm
Steering Ball
8mm
Steering Ball
8mm
Steering Ball
8mm
Steering Ball
Washer
8mm
Steering Ball
Washer
39150
38265
37430
39140
39140
39141
Make steering
ball move
smooth.
Make steering
ball move
smooth.
Assembly of the right and left-side are the same.
Push 2 ball
bearings into
knuckle arm
as shown.
*Notice the direction
of the hex screw.
Step 1
Step 3
Step 2
2x9.8mm
Pin
CVA Dog Bone
38524
38523
CVD Shaft
ASSEMBLY OF THE FRONT SUSPENSION ARMS Assembly of the right and left-side are the same.
3x8 mm
Set Screw
3x8 mm
Set Screw
3x8 mm
Set Screw
38399
RIGHT SIDE
38399
38399
38399
37360
37360
Front Upper
Arm
Front Upper Arm
Front Lower
Arm
Front Lower Arm
4mm
4mm Ball&Socket
Ball&Socket
FRONT KNUCKLE
ARM ASSEMBLY.
FRONT KNUCKLE
ARM ASSEMBLY.
3 x 8mm set screw is
used to adjust the
ride height.
A 3 x 8mm set screw
is used to adjust the
ride height.
LEFT SIDE
39150 37430 37450 39140
37450
38406
39150
39141
37430
38265
94035
94035
94035

ASSEMBLY OF THE REAR SUSPENSION ARMS
3x8 mm
Set Screw
3x8 mm
Set Screw
Ball & Socket
37360
Ball & Socket
Ball & Socket
M3x16 mm
Screw
M3x16 mm
Screw
6 mm
Ball & Socket
6 mm
Ball & Socket
Rear Upper Arm
38399
38398
37370
37370
3x20mm
3x20mm
Turnbuckle
Turnbuckle
(Right- Hand Side)
9 mm
38399
Rear Lower Arm
Rear Lower Arm
A 3 x 8mm set screw is used
to adjust the ride height.
3x8 mm
Set Screw
M3x16 mm
Screw
6 mm
Ball & Socket
38399
38399
38399
37370
Upper Arm
Plastic Rod End
Upper Arm
Plastic Rod End
Rear Upper Arm
Rear Upper Arm
(Left- Hand Side)
A 3 x 8mm set screw is used
to adjust the ride height.
Push 2 ball bearings into
rear wheel hub as shown.
ASSEMBLY OF THE REAR WHEEL HUB
10mm Alum.
Set Screw
10mm Alum.
Set Screw
10mm Alum.
Set Screw
5x11x4mm
Ball Bearing
5x11x4mm
Ball Bearing
10x15x4mm
Ball Bearing
Rear Wheel
Hub
8mm
Steering Ball
Washer
8mm
Steering Ball
Washer
39150
37430
37430
38266
38267
37450
39141
39141
Rear Wheel
Axle Shaft
Notice the direction
of the steering ball
washer.
Assembly of the right and left-side are the same.
Assembly of the right and left-side are the same.
Push
10x15x4mm
Ball Bearing
8mm
Steering Ball
Push
39150
39150
37450
39140
94005
38399
94035
37360
94005
94035
38399
37360
94035
94005

M3
Nylon Nut
38288
38289
Servo Saver
38289
Servo Saver
38289
Servo Saver
38289
Servo Saver
38644
35958
35958
36742
37360
4mm
Ball & Socket
37360
4mm
Ball & Socket
37360
4mm
Ball & Socket
M3x12mm
Screw
M3x12mm
Screw
M3x12mm
Screw
Servo Saver
Spring
Servo Saver
Bushing
3x6x2.5mm
Brass Bushing
3x6x2.5mm
Brass Bushing
5x8x2.5 mm
Brass Bushing
5x8x2.5 mm
Brass
Bushing
ASSEMBLY OF THE SEVRO SAVER
M3
Nylon Nut
38281
38276
38277
36742
4mm
Ball & Socket
3x40mm
Turnbuckle
37650
4mm
Ball End (Long)
37650
4mm
Ball End (Long)
M3x10mm
Screw
M3x12mm
Screw
Servo Saver
Spring
Servo Saver
Bushing
3x6 mm
Brass Bushing
5x8 mm
Brass Bushing
A
B
A
A
B
Made two steering rod for left and
right hand side.
Put steering rod into
4mm ball & socket.
Put steering rod into
4mm ball & socket.
Snap steering rod into
4mm ball & socket.
*Use the long ball end for both steering rod and steering servo rod.
Steering Rod
3x6x2.5m
Ballbearing x2
5x8x2.5mm
Ballbearing x2
38644 Ballbearing Set
(For servo Saver )
Option:
Approx 57 mm
38281
37650
4mm
Ball End (Long)
3x36mm
Turnbuckle
37650
4mm
Ball End
(Long)
Steering Servo Rod
Approx 54 mm
ASSEMBLY OF THE SEVRO SAVER
AND STEERING RODS
M3
M3
38275
38528
Nylon Nut
Nylon Nut
M3x10mm
Flat Head
HexScrew
M3x10mm
Flat Head
HexScrew
M3x5mm
Flat Head
Hex Screw
Servo saver
Screw
Cd3 Stock
Chassis
M3
Nylon Nut
M3x5mm
Flat Head
Hex Screw
38275
Servo saver
Screw
M3x10mm
Flat Head
HexScrew
Front Gear
Box Assembly.
Arm Holder for 0
(Lower/Rear)
cS rew
Cement
35958
38288
94004
94003
37360
94041
94041
94004
94004
94004
38263
94041
94041
94019
94018
94018
94041
38644
94019 94019

ASSEMBLY OF THE FRONT ARM HOLDER
ONTO CHASSIS
ASSEMBLY OF THE FRONT STABILIZER
38263
Lower Arm Holder for 0 and 1.5 and
2.5 degree.
38419
38263
M3x3mm
M3x3mm
M3x10mm
Flat Head
HexScrew
For assembly stabilizer:
37360
4mm
Ball & Socket
3X55mm
Lower Arm Shaft
M3x10mm
Flat Head
Hex Screw
M3x16mm
Screw
2.5mm
E-Ring
M3x3mm
Set Screw
4mm
Ball & Socket
38419
3x55mm
Lower Arm Shaft
38418
M3x16mm
M3x16mm
M3x3mm
M3x3mm
Assembly of front stabilizer 2.5mm
2.5mm
Stabilizer
Mount
Screw
Screw
Set Screw Set Screw
E-Ring
E-Ring
Stabilizer
Mount
*Turn stabilizer balance adjuster to
adjust the stabilizer to the same angle.
*Keep stabilizer ball in the center.
Stabilizer
Stabilizer
Balance
Adjuster
Arm Holder
(Front/Lower)
Insert the drive shaft
before assembly.
Assembly of the right and left-side are the same.
Use the 0 degree for
front arm holder. *Put steering rod into
4mm ball & socket
..
* Use a 3mm drill to
hone out the front
lower arm holder.
Center
94033
94019
37360
94005
94033
94005
94033 38420
94033
94005
38418
94019
90020
90020
90020

38518
2.5mm
E-Ring
M3X3mm
Set Screw
M3X16mm
Screw
M3x3mm
Set screw
M3x3mm
Set screw
M3x16mm
Screw
M3x16mm
Screw
90020
2.5mm
E-Ring
90020
2.5mm
E-Ring
38420
stabilizer
38418
Stabilizer
Mount
38418
Stabilizer
Mount
38418
Stabilizer
Balance
Adjuster
ASSEMBLY OF THE REAR STABILZER
Assembly of rear stabilizer
*Keep stabilizer ball in the center.
*Turn stabilizer balance adjuster to
adjust the stabilizer to the same angle.
ASSEMBLY OF THE FRONT STIFFENER
ONTO CHASSIS
ASSEMBLY OF THE REAR STIFFENER
ONTO CHASSIS
38518
38518
Front Stiffener (Left)
Front Stiffener (Right)
M3x8mm
Screw
M3x8mm
Screw
M3x10mm
Flat Head
HexScrew
M3x10mm
Flat Head
HexScrew
M3x10mm
Flat Head
HexScrew
M3x10mm
Flat Head
HexScrew
38518
Rear Stiffener (Right)
Rear Stiffener (Left)
M3x10mm
Flat Head
Hex Screw
M3x10mm
Flat Head
Hex Screw
M3x8mm
Screw
M3x8mm
Screw
M3x8mm
Screw
M3x8mm
Screw
Center
94005
94033
94005
94005
94003
94032
94019
94019
94002
94002
94002
94019
94033
94019
94032 94032
94019
94019

ASSEMBLY OF THE REAR GEAR BOX
AND ARM HOLDER ONTO CHASSIS
M3x10mm
Flat Head
HexScrew
M3x10mm
Flat Head
HexScrew
M3x10mm
Flat Head
HexScrew
M3x10mm
Flat Head
HexScrew
Arm holder
(Rear/Front)
Rear Gear Box
Assembly
Use the 0 degree for
rear arm holder.
ASSEMBLY OF THE REAR BLOCK ONTO CHASSIS
M3x10mm
Flat Head
HexScrew
M3x3mm
Set Screw
M3x10mm
Flat Head
Hex Screw
3x55mm
Lower Arm Shaft
3x55mm
Lower Arm Shaft
Arm Holder
(Rear / Rear)
38263
Use the 0 degree for
rear arm holder.
Assembly of the right and left-side are the same.
38263
Lower Arm Holder for 0 and 1.5 and
2.5 degree.
M3x3mm
Set Screw
38263
94019
94019
94019
38419
94033
94033 38419
94019
94019

M3x10mm
Flat Head
Hex Screw
38520
Brake Mount
(Lower)
ASSEMBLY OF THE TWO SPEED ONTO CHASSIS
M3x30mm
Flat Head
Hex Screw
M3x25mm
Flat Head
Hex Screw
M3x25mm
Flat Head
Hex Screw
Center Drive Shaft
(Long/Front)
Center Drive Shaft
(Short/Rear)
2-Speed Assembly
Brake Mount
Assembly (Upper)
38527
38527
*Insert the center drive shaft
before assembly the two speed
onto chassis.
Screw
M3X8mm
Screw
M3X8mm
Screw
M3X10mm
Screw
M3X10mm
Screw
M3X8mm
Washer
M3X8mm
Washer
M3X8mm
Washer
Radio Tray
Servo Post
Servo Post
Servo Post Washer
Servo Post Washer
38517
38520
38520
38520
38520
Steering Servo
Steering Servo After Assembly.
37360
4mm
Ball & Socket
10768
Steering
Servo Horn
Use the screw
from your servo.
90 Degree
Align the servo horn in 90 degree.
ASSEMBLY OF THE STEERING SERVO
94002
M3X8mm
Screw
94003
M3X10mm
Screw
M3x10mm
Flat Head
Hex Screw
M3x30mm
Flat Head
Hex Screw
M3x25mm
Flat Head
Hex Screw
Note:
Use M3x30mm flat head screw
only in this position.
The mark on the center
drive shaft is used for the front.

Caster Angle
Adjuster(1.5mm)
Caster Angle
Adjuster
(1.0mm)
Front Upper
Arm Shaft
Front Upper
Arm Shaft
39141
38261
Insert the front caster angle adjuster into front upper arm.
Assembly of the right and left-side are the same.
Assembly of the right and left-side are the same.
1.5mm 1mm
ASSEMBLY OF THE FRONT SHOCK STAY ONTO FRONT
GEAR BOX
M3x8mm
Screw
M3x12mm
Screw
M3x8mm
Screw
M3x12mm
Screw
ASSEMBLY OF THE REAR SHOCK STAY ONTO REAR
GEAR BOX
M3x8mm
Screw
M3x12mm
Screw
M3x12mm
Screw
M3x8mm
Screw
Rear Drive
Shaft
Rear Drive
Shaft
38268
38268
2.5mm
E-Ring
2.5mm
E-Ring
2.5mm
E-Ring
2.5mm
E-Ring
2.5mm
E-Ring
2.5mm
E-Ring
2.5mm
E-Ring
* Insert the rear driver shaft
before assembly the upper arm.
94004
94002
90020
94004 94002
39141
94002 94004
38261
94004
94002
90020
90020
90020
90020
90020
90020

37967
P3
O-Ring
(2 pcs)
P12 O-Ring
38331-GRAY
Adjust Nut(Gray)
37650
4mm
Ball End
Piston
Shock Shaft
Shock Oil
Pull down piston
and pour oil into
shock cylinder.
Remove air bubbles
by slowly moving
piston up and down
several times.
2mm
E-Ring
37967
C-Ring
37967
Washer
(Block)
Use a little shock oil to
lubricate o-rings before
screwing on adjusting nut.
ASSEMBLY OF THE LEXAN SHOCK ABSORBERS
FILLING THE SHOCKS WITH OIL
OilOil
37965
Alum Shock Body
38325
37100
37966
Use the No.2 for two hole
piston from shock plastic
tree.
*Insert the o-ring
into the groove
of the adjust nut.
* Use the short ball end .
The C-Ring must fit
into the groove.
Step 1
Step 2
Ball End
( Short)
Pressure Top
Shock Spring
Spring Holder
Shock Cap
(Gray)
ASSEMBLY THE SHOCK SPRING
38330 GRAY
37100
37080
38326
37100
Use the short shock
ball end.
Pull down piston
and pour oil into
shock cylinder.
Remove air bubbles
by slowly moving
piston up and down
several times.
37070
3mm O-Ring
37070
3mm O-Ring
37070
3mm O-Ring
Clear Lexan
Shock Body
37100
Front Cap
37650
4mm
Ball End
Piston
Shock Shaft
Shock Oil
Pressure Top
Shock Cap
(Gray)
Spring collar
Spring
tension adjust
Ball end
Shock Spring
Spring Holder
2mm E-Ring
2mm E-Ring
2mm E-Ring
39030
38325 37100
37080
38330
Use the No.2 for two
hole piston from
shock plastic tree.
Use the short ball end .
FILLING THE SHOCKS WITH OIL
OilOil
37100
37100
38326
37100
ASSEMBLY THE SHOCK SPRING
ASSEMBLY OF THE ALUMINUM CNC SHOCK ABSORBERS
(USED ON SPORT RTR MODELS)
(USED ON PRO RTR MODELS)

Step 1
Put the receiver and
battery into box.
M3X16mm
Screw
M3X16mm
Screw
Screw
Servo Post Washer
2mm
Servo Post Washer
2mm
Servo Post Washer
2mm
Servo Post Washer
2mm
Battery Cover
Antenna pipe
Body Clip
Battery
Receiver
Servo Post
Servo Post
THROTTLE
SERVO
M3x8mm
Washer
M3x8mm
Washer
*Use the screw provided
from your servo.
10280
Switch Cover
Switch
M3X16mm
Screw
38520
38520
38520
38520
38518
30560
37410
38520
38520
Step 2
94005
94005
94005
ASSEMBLY OF THE FUEL TANK ONTO CHASSIS
M3X8mm
Screw
M3X8mm
Screw
Fuel Nipple
Fuel Nipple
Cd3 Fuel Tank
38521
38518
Fuel Tank Post
M3X8mm
Screw
M3x10mm
Flat Head
Screw
M3x10mm
Flat Head
Screw
94002
94003
94002
94002
94019

M3x10mm
Flat Head
Hex Screw
M3x10mm
Flat Head
Hex Screw
Front Bumper
Front Bumper
Top Plate)
Front Bumper
Post Tube Front Bumper
Post Tube
Front Bumper
Post Tube
Insert body
pins into body
holder to the
desired
height.
Body Post
(Front)
Body Holder
Body Holder
Body Pin
Body Pin
Body Post
(Front)
M3x12mm
Screw
M3x12mm
Screw
38291
38291
38291
38291 38291
39320
39320
39320
37410
37410
37410
M3x10mm
Flat Head
Screw
94019
94019
94019
94004
M3x10mm
Flat Head
Screw
M3x10mm
Flat Head
Screw M3x10mm
Flat Head
Screw
M3x8mm
Screw
M3x8mm
Screw
M3x10mm
Flat Head
Screw
M3x8mm
Screw
ASSEMBLY OF THE RADIO TRAY ONTO CHASSIS
94019
94002
94019
94019
94002
94002

M3x12
Screw M3x12
Screw
38329
6mm Alum.
Ball & socket
(Gray)(Short)
38282
6mm Alum.
Ball & socket
(Long)
37360
4mm
Ball & socket
37360
4mm
Ball & socket
ASSEMBLY OF THE FRONT SHOCK INTO
SHOCK TOWER
ASSEMBLY OF THE REAR SHOCK INTO
SHOCK TOWER
Snap ball end
into 37360 as
shown.
94004
94004
M3x12mm
Screw
M3x12mm
Screw
Foam Bumper
38294
ASSEMBLY OF THE FRONT POST
M3x12mm
Screw
M3x16mm
Flat Head
Screw
M3x16mm
Flat Head
Screw
M3x8mm
Screw
M3x8mm
Screw
94002
94021
94002
94004
94021 94020
94020
Snap ball end
into 37360 as
shown.

M3
Nylon Nut
M3
Nylon Nut
M3x20mm
Cap Screw
M3x20mm
Cap Screw
M3x12mm
Cap Screw
M3x12mm
Cap Screw
ASSEMBLY OF THE ENGINE ONTO ENGINE MOUNT ASSEMBLY OF THE MANIFOLD
Manifold Gasket
38529
Manifold
(side exhaust)
Note:
Put the nylon nut
into the groove of the
engine mount.
38150
38150
Engine Mount
Engine Mount
38162
34110
5x10x4mm
Ball Bearing
5x8x2.5mm
Ball Bearing
3X6 mm
Washer
M3x5mm
CAP Screw
Clutch Bell
22T-2nd
Clutch Gear
18T-1st
Clutch Gear
35951
38309
35958
ASSEMBLY OF THE ENGINE AND 2-SPEED CLUTCH BELL
38307
90019
30702
94041
30702
94041
90019