OHAUS Frontier FC5513R User manual

FrontierTM Centrifuge
FC5513 & FC5513R
Instruction Manual

Front and rear view of the centrifuge FC5513
3
5
6
7
Figure.1
Front and rear view of the centrifuge FC5513R
Figure.2
1 Centrifuge Lid
2 Rotor Window
3 Display
4 Function Label
5 Main Power Switch
6 Power Connection
7 Emergency Release
Function Label
Function Label for FC5513
Figure.3
1
2
4
7
6
3
5
1
2
4

Function Label for FC5513R
Figure.4
1 LCD Display
2 Store setup information
3 Program setup model
4 Adjusting Dial: Change the
number
5 RPM/RCF model and select
6 Acceleration/Deceleration intensity
model and select
7 Temperature setup model (Only
FC5513R)
8 Short/quick spin centrifugation
9 Stop centrifugation / Release lid
10 Start centrifugation
11 Time setup model
LCD Display
The following picture shows the individual elements of the LCD-display.
Figure.5
Figure.6
M8
M13
M15
M14
M2
M3
M1
M12
M4
M5
M6
M7
M9
M11
M10
A-4
A-3

Display fields:
A-1 Display fields –"RPM/RCF"
A-2 Display fields –"Acc/Dec" "Service"
A-3 Display fields –"Time/Prog"
A-4 Display fields –"Temp"
Messages/logos of the display fields
M1
"close"
M2
"open"
M3
"rotor"
M4
"rotor no"
M5
"rpm"
M6
"rcf"
M7
"accel"
M8
"decel"
M9
"radius"
M10
"program"
M11
"error"
M12
"service"
M13
“h m s”
M14
“temperature”
M15
“precool”
Rotor No. Table
Rotor No.
display
Order No.
Capacity
Fit model
02
30472302
Rotor Angle 24×1.5/2.0ml BIOSEALS V1
FC5513 and FC5513R
04
30472304
Rotor Hematocrit 24xCapillaries V1
FC5513
06
83041006
Rotor Angle 18x1.5/2.0ml Sealable
FC5513R
14
83041014
Rotor Angle 4x8-Place PCR Stripes V1
FC5513 and FC5513R
98
30210898
Rotor Angle 24×2.0ml Spin Column
FC5513

FrontierTM Centrifuge FC5513&FC5513R EN-1
TABLE OF CONTENTS
1. INTRODUCTION...................................................................................................................................................3
1.1 Description....................................................................................................................................................3
1.2 Features........................................................................................................................................................3
1.3 Definition of Signal Warnings and Symbols .................................................................................................3
1.4 Safety Precautions........................................................................................................................................4
1.4.1 User...........................................................................................................................................................4
1.4.2 Rotor and accessories..............................................................................................................................4
1.4.3 Measures for your protection....................................................................................................................4
1.4.4 Exclude the following environmental influences.......................................................................................4
1.4.5 Measures for operational safety ...............................................................................................................5
1.4.6 Danger and precautions ...........................................................................................................................5
1.4.7 Abbreviations used in this manual............................................................................................................5
2. INSTALLATION ....................................................................................................................................................6
2.1 Unpacking.....................................................................................................................................................6
2.1.1 Delivery package for FrontierTM FC5513 ..................................................................................................6
2.1.2 Delivery package for FrontierTM FC5513R................................................................................................6
2.2 Selecting the Location ..................................................................................................................................6
2.3 Installation.....................................................................................................................................................6
2.4 Safety precautions during operation.............................................................................................................7
3. OPERATION .........................................................................................................................................................8
3.1 Mounting and loading rotor...........................................................................................................................8
3.1.1 Installation of rotors ..................................................................................................................................8
3.1.2 Loading angle rotors.................................................................................................................................9
3.1.3 Loading and overloading of rotors............................................................................................................9
3.1.4 Removing the rotor ...................................................................................................................................9
3.1.5 Power switch and fuse..............................................................................................................................9
3.2 Lid control ...................................................................................................................................................10
3.2.1 Lid open..................................................................................................................................................10
3.2.2 Lid lock....................................................................................................................................................10
3.3 Preselection................................................................................................................................................10
3.3.1 Preselection of speed / RCF-value.........................................................................................................10
3.3.2 Preselection of running time...................................................................................................................11
3.3.3 Preselection of brake intensity and acceleration....................................................................................12
3.3.4 Pre-selection of temperature (Only FC5513R).......................................................................................12
3.3.5 Pre-cooling (Only FC5513R) ..................................................................................................................12
3.4 Radius correction........................................................................................................................................13
3.5 Program ......................................................................................................................................................13
3.5.1 Storage of programs...............................................................................................................................13
3.5.2 Recall of stored programs.......................................................................................................................14
3.5.3 Leaving program mode...........................................................................................................................15
3.6 Starting and stopping the centrifuge...........................................................................................................15
3.6.1 Starting the centrifuge.............................................................................................................................15
3.6.2 The "STOP/Lid" key................................................................................................................................15
3.7 Imbalance detection....................................................................................................................................16
4. SETTING.............................................................................................................................................................17
4.1 Basic adjustments.......................................................................................................................................17
4.1.1 Change the type of rotor.........................................................................................................................17
4.1.2 Access to mode "Operating Data"..........................................................................................................17
4.1.3 Signal turn on / off...................................................................................................................................18
4.1.4 Keyboard sound turn on / off ..................................................................................................................19
4.1.5 Sleep Mode On / Off...............................................................................................................................19
4.1.6 Call up operating data.............................................................................................................................19
5. MAINTENANCE..................................................................................................................................................21
5.1 Maintenance and cleaning..........................................................................................................................21
5.1.1 General Care ..........................................................................................................................................21
5.1.2 Cleaning and disinfection of the unit.......................................................................................................21
5.1.3 Cleaning and disinfection of the rotor.....................................................................................................21
5.1.4 Disinfection of aluminum rotors ..............................................................................................................22
5.1.5 Disinfection of PP-rotors.........................................................................................................................22
5.1.6 Glass breakage.......................................................................................................................................22
6. TROUBLESHOOTING........................................................................................................................................23
6.1 Error message: Cause / Solution................................................................................................................23

EN-2 FrontierTM Centrifuge FC5513&FC5513R
6.2 Survey of possible error messages and their solutions..............................................................................23
6.2.1 Lid release during power failure (Emergency Lid Release) ...................................................................23
6.2.2 Description of the error message system...............................................................................................23
7. RECEIPT OG CENTRIFUFES TO REPAIR .......................................................................................................24
8. TRANSPORT AND STORAGE ..........................................................................................................................25
8.1 Transport.....................................................................................................................................................25
8.2 Storage .......................................................................................................................................................25
9. TECHNICAL DATA.............................................................................................................................................26
9.1 Specifications..............................................................................................................................................26
9.1.1 Centrifuge FC5513..................................................................................................................................26
9.1.2 Centrifuge FC5513R...............................................................................................................................27
9.2 Drawings and dimensions...........................................................................................................................28
10. ORDER INFORMATION.................................................................................................................................29
11. COMPLIANCE................................................................................................................................................29
12. APPENDIX......................................................................................................................................................30
12.1 Table 1: Permissible net weight..................................................................................................................30
12.2 Table 2: Max. speed and RCF-values for permissible rotors.....................................................................30
12.3 Table 3: Lowest temperatures at max. speed ............................................................................................30
12.4 Table 4: Acceleration and deceleration times ............................................................................................31
12.5 Table 5: Error messages ............................................................................................................................32
12.6 Table 6: Radius correction..........................................................................................................................33
12.7 Table 7: Symbols- / Abbreviations..............................................................................................................33
12.8 Table 8: Redemption form / Decontamination certificate ...........................................................................34

FrontierTM Centrifuge FC5513&FC5513R EN-3
1. INTRODUCTION
1.1 Description
Thank you for choosing this OHAUS product.
All symbols indicate safety instructions and points to potentially dangerous situations. Please read the manual
completely before using the FrontierTM FC5513 & FC5513R to avoid incorrect operation.
FrontierTM FC5513 & FC5513R centrifuge was designed for the separation of materials or mixtures with different
density.
1.2 Features
The FrontierTM FC5513 & FC5513R centrifuge offers many practical features such as:
• High performance, reach up to 17,317 x g
• Rotor options for microtubes, spin column kit, and capillaries
• Remarkably small footprint to save invaluable benchtop space
• Ergonomic touch-wheel makes parameter adjustment fun
• Splash-proof front panel can endure sample spill and is easy to clean
• Distinct Intuitive control panel interface can be operated by one hand
• All key parameters are visible at all times
1.3 Definition of Signal Warnings and Symbols
Safety notes are marked with signal words and warning symbols. These show safety issues and warnings. Ignoring
the safety notes may lead to personal injury, damage to the instrument, malfunctions, and false results.
The degree of danger is a part of a safety note and distinguishes the possible results of non-observance from each
other.
Signal Words
DANGER
Will lead to severe injuries or death if not avoided.
WARNING
For a hazardous situation with medium risk, possibly resulting in injuries or death
if not avoided.
CAUTION
For a hazardous situation with low risk, resulting in damage to the device or
the property or in loss of data, or injuries if not avoided.
ATTENTION
For important information about the product. May lead to equipment damage if
notavoided
NOTE
For useful information about the product
Warning Symbols
General Hazard Electrical Shock Hazard
Alternating Current Biohazard
Explosion Crushing

EN-4 FrontierTM Centrifuge FC5513&FC5513R
Warning and information signs on the surface of centrifuge
Four carrier must be used at all times on four place swing out rotors or damage
will occur to the centrifuge. Such damage will not be covered under the product
warranty.
Attention! Check the fastening of the rotor nut before each run.
Take off mains plug before opening the housing or the emergency release.
Power Input
Direction of Rotation –clockwise rotation for the rotor drive (only FC5513R)
1.4 Safety Precautions
1.4.1 User
OHAUS centrifuges are intended exclusively for indoor use and for use by qualified personnel. This device may
onlybe operated by trained specialist stuff. They must have carefully read the operating manual and be familiar with
the function of the device.
1.4.2 Rotor and accessories
Only OHAUS original rotors and accessories shall be used. Any other use or intended use is considered improper.
OHAUS is not liable for damage resulting from improper use.
CAUTION:
Read all safety warnings before installing, making connections, or servicing this equipment. Failure to
comply with these warnings could result in personal injury and/or property damage. Retain instructions
for future reference.
1.4.3 Measures for your protection
WARNING: Never work in an environment subject to explosion hazards! The housing of the instrument
is not gas tight. (Explosion hazard due to spark formation, corrosion caused by the ingress of gases)
WARNING: When using chemicals and solvents, comply with the instructions of the producer and the
general lab safety rules.
WARNING: The centrifuge is not sealed. Use suitable protection measures when using the centrifuge
for infectious and pathogenic samples. Follow appropriate safety precautions when handling these
samples.
1.4.4 Exclude the following environmental influences
• Powerful vibrations
• Direct sunlight
• Atmospheric humidity greater than 80%
• Corrosive gases present
• Temperatures below 2 °C and above 35 °C
• Powerful electric or magnetic fields:
WARNING:
Electrical shock hazards exist within the housing. The housing should only be opened by authorized and
qualified personnel. Remove all power connections to the unit before opening.

FrontierTM Centrifuge FC5513&FC5513R EN-5
1.4.5 Measures for operational safety
• Do not unscrew the two halves of the housing
• Dry off any liquid spills immediately! The instrument is not watertight
• Verify that the equipment’s input voltage range and plug type are compatible with the local power supply.
•
Only connect the power cord to a properly grounded power receptacle.
•
Only use a power cord with a rating that exceeds the specifications on the equipment label.
• Do not position the equipment such that it is difficult to disconnect the power cord from the power receptacle.
• Make sure that the power cord does not pose a potential obstacle or tripping hazard.
• The equipment is for indoor use only. Use the equipment only in dry locations.
• Use only approved accessories.
• Operate the equipment only under ambient conditions specified in these instructions.
• Disconnect the equipment from the power supply when cleaning.
• Do not operate the equipment in hazardous or unstable environments.
• Service should only be performed by authorized personnel.
1.4.6 Danger and precautions
To protect people and environment the following precautions should be observed:
• During centrifugation, the presences of people are prohibited within 30 cm around the centrifuge according
tothe regulations of EN 61010-2-020.
• FC5513& FC5513R are not explosion-proof and must therefore not be operated in explosion-endangered
areas or locations.Centrifugation of flammable, explosive, radioactive, or such substances, which chemically
react with high energy, is strictly prohibited. The final decision on the risks associated with the use of such
substances is the responsibility of the user of the centrifuge.
• Never spin toxic or pathogenic material without adequate safety precautions, i.e. centrifugation of buckets /
tubes with missing or defective hermetic sealing is strictly prohibited. The user is obliged to perform appropriate
disinfection procedures in case dangerous substances have contaminated the centrifuge and or its
accessories.When centrifuging infectious substances, always pay attention to the general laboratory
precautions. If necessary, contact your safety officer!
• It is prohibited to run the centrifuge with rotors other than listed for this unit.
• Under no circumstances open the lid of the centrifuge while the rotor is still running or rotating with a speed of
>2m/s.
1.4.7 Abbreviations used in this manual
Symbol/Abbreviations
Unit
Description
RPM
[min-1]
rpm
revolutions per minute
RCF
[x g]
relative centrifugal force
PCR
PCR Polymerase chain reaction
PP
-
Polypropylene
PC
-
Polycarbonate
accel
-
acceleration
decel
-
deceleration
prog
-
program

EN-6 FrontierTM Centrifuge FC5513&FC5513R
2. INSTALLATION
2.1 Unpacking
Carefully remove your centrifuge and each of its components from the package. The included components vary
depending on the centrifuge model (see table below). Save the packaging to ensure safe storage and transport.
Theinstruction manual must always be kept with the centrifuge!
Rotor(s) / Accessories will be packed separately.
2.1.1 Delivery package for FrontierTM FC5513
Quantity
Description
1
Centrifuge FC5513
1
Power Cable
1
Warranty Card
1
Instruction Manual
1
Rotor Key
1
Rotor Nut
2.1.2 Delivery package for FrontierTM FC5513R
Quantity
Description
1
Centrifuge FC5513R
1
Power Cable
1
Warranty Card
1
Instruction Manual
1
Rotor Key
1
Rotor Nut
2.2 Selecting the Location
ATTENTION:
Avoid excessive vibrations, heat sources, air current, or rapid temperature changes.
• The centrifuge should be installed on an even, solid and level surface, if possible, on a laboratory cabinet /
tableor some other solid vibration free surface.
• During centrifugation, the centrifuge must be placed in a way, that there is a minimum space of 30 cm on
eachside of the unit, according to the standards EN 61010-2-020.
• Do not place the centrifuge next to a window or a heater, where it could be exposed to excessive heat, as
theperformance of the unit is based on an ambient temperature of 23 °C.
2.3 Installation
Follow these steps:
• Check whether the power supply corresponds with the one specified on the manufacturer's rating label,
whichis located on the rear panel.
• The line voltage circuit breaker is max. 10 A (type K) slow release for commonly used instruments.
• In case of emergency, there must be an emergency switch off installed outside the room in order to
disconnectthe power supply from the unit.
• Connect the centrifuge to a grounded power receptacle.
• Turn the instrument on, by using the mains power switch.
• Open the lid by using the Stop / Lid button.
• Remove the transport securing device of the motor.

FrontierTM Centrifuge FC5513&FC5513R EN-7
2.4 Safety precautions during operation
• Do not operate the centrifuge in case it is not installed correctly.
• Do not lean on the centrifuge during operation.
• Do not stay within the 30 cm clearance envelope longer than necessary for operational reasons.
• Do not place any potentially hazardous materials within the 30 cm clearance envelope.
• Do not operate the centrifuge when disassembled (e.g. without housing).
• Do not run the centrifuge when mechanical or electrical components have been tampered with.
• Do not use accessories such as rotors and buckets, which are not exclusively approved by OHAUS
Corporation,except commercially available centrifuge tubes made of glass or plastic.
• Do not spin extremely corrosive substances, as they may damage or weaken the materials.
• Do not operate the centrifuge with rotors or buckets, which show any signs of corrosion or mechanical damage.
The manufacturer is responsible for safety and reliability of the centrifuge, only if:
• The unit is operated in accordance with this instruction manual.
• Modifications, repairs, or other adjustments are performed by authorized personnel and the electrical
installationcomplies with the relevant electrical codes.

EN-8 FrontierTM Centrifuge FC5513&FC5513R
3. OPERATION
3.1 Mounting and loading rotor
3.1.1 Installation of rotors
For FC5513 centrifuge packaged with rotor already installed, these following steps are not necessary.
Clean the drive shaft as well as the collet with a clean, grease-free piece of cloth. Place the rotor onto the drive shaft.
(see figure below). Take care that the rotor is fully installed onto the motor shaft.
Motor shaft and chamber –FC5513
Motor shaft and chamber –FC5513R
Figure.7
Nut for Rotor
Tool for rotor
Screw-on lid
Screw-on lid
Figure.8-1
Figure.8-2
Figure.8-3
Figure.8-4
The rotors have to be locked with provided rotor key. Therefore, hold the rotor with one hand andsecure the rotor by
turning the fixing nut clockwise (see figures 8)
We will provide a tool for nut-nut rotor with centrifuge.
ATTENTION:
Check that the fixing screw is properly installed before each run. (see figures 8)
Do not operate the centrifuge with rotors or buckets which show any signs of corrosion or mechanical
damage.
Do not operate with extremely corrosive substances, which could damage the rotor, buckets, and
materials.
In case of any questions, please contact the manufacturer!

FrontierTM Centrifuge FC5513&FC5513R EN-9
3.1.2 Loading angle rotors
Rotors must be loaded symmetrically and with equal weight (see figure below). The adapter may only be loaded with
the appropriate vessels. The weight differences between the filled vessels should be kept as low as possible.
Therefore, we recommend weighing them with a balance. This reduces the wear of the drive and the acoustic
operating noise.
On each rotor, the maximum load per hole is stated.
Figure.9 WRONG
Figure.10 CORRECT (12 tubes)
3.1.3 Loading and overloading of rotors
All approved rotors are listed with their maximum speed and maximum filling weight in "table 2 permissible net
weight" (See APPENDIX).
The maximum load permitted for a rotor, which is determined by the manufacturer, as well as the maximum speed
allowed for this rotor (See label on rotor), must not be exceeded. The liquids the rotors are loaded with, should
have a maximum homogeneous density of 1.2 g/ml or less when the rotor is running at maximum speed.
In order to spin liquids with a higher density, the speed has to be reduced according to the following formula:
Reduced speed nred =√1,2
ℎ𝑖𝑔ℎ𝑒𝑟 𝑑𝑒𝑛𝑠𝑖𝑡𝑦 xmax. speed (nmax) of the rotor
Example:
nred =√ 1,2
1,7 x4.000 =3.360 rpm
If in case of any questions, please contact the manufacturer!
3.1.4 Removing the rotor
Untighten the rotor fixing nut completely (screw over the stiff point) and lift the rotor vertical out of the centrifuge. (see
figure 8).
3.1.5 Power switch and fuse
The power switch is located on the back side or in the front of the centrifuge (see figure 11).
ATTENTION: After turning on the power switch, open the centrifuge lid first, before starting the centrifuge
Fuse drawer with fuse 4 AT
Figure.11-1 Power Switch and Fuse (FC5513)
Figure.11-2 Power Switch (FC5513R)

EN-10 FrontierTM Centrifuge FC5513&FC5513R
3.2 Lid control
3.2.1 Lid open
Before the run, when the lid of the centrifuge is closed, the word "close" (M1) appears in the display "RPM | RCF"
(A-1). Additionally, the code number of the preset rotor is shown in the display. Even if the rotor is not inserted. By
pressing the key "Stop/Lid" (9) you can release the lid of the centrifuge. As soon as the lid is completely released,
the word "open" (M2) appears. Now you can open the lid of the centrifuge.
Please refer to figure 12 below for reference.
M2 M4 M3 M1
A-1
9
Figure. 12
During the run you can call up the rotor type at any time by pressing the key "Stop/Lid" (9).
3.2.2 Lid lock
The lid should only be put down slightly. A lid lock closes the lid, at the same time the word "open" (M2) disappears
(refer to figure 15).
As a sign that the centrifuge is ready for starting, in the display "RPM | RCF" (A-1) the word "close" (M1) appears.
Simultaneously the word "rotor" (M3) is displayed, as well as the code number of the rotor, which is in the centrifuge
system, "no 71" (M4). With that, all rotor specific data, like e. g. max. speed, acceleration etc., are adopted.
ATTENTION:
Don't grip your fingers between lid and device or locking mechanism when closing the lid!
Before closing the lid, please check if the rotor is tightened.
3.3 Preselection
3.3.1 Preselection of speed / RCF-value
This pre-selection is activated through the key "RPM/RCF" (5) (refer to figure 13 below). By pressing the key once
the word "rpm" (M5) flashes. By pressing the key twice, the pre-selection of the centrifugal forces can be selected.
Then the flashing word "rcf" (M6) appears. You can set the desired values with the adjusting dial (1). In the display
(A-1) the regulated value is shown permanently, before, during and after the run.
4

FrontierTM Centrifuge FC5513&FC5513R EN-11
M5 M6
A-1
5
5
Figure. 13
As long as no rotor is inserted, the speed is adjustable between 200 rpm and maximum revolution of the centrifuge.
If there is a rotor in the centrifuge the speed can only be pre-selected until the maximum permissible revolution of
that rotor. It is the same with the pre-selection of the RCF-value. The setting range is between 20 x g and the
maximum permissible centrifugal force of the rotor.
See "Table 4: max. speed and RCF-values for permissible rotor" (See APPENDIX). All-important values are
listed there.
ATTENTION:
Please also check the maximum permissible revolutions of your test tubes with the manufacturer.
3.3.2 Preselection of running time
The running time can be pre-selected in three different ranges from 10 seconds up to 99 hours 59 minutes.
1. Range from 10 seconds up to 59 minutes 50 seconds in steps of 10 seconds
2. Range from 1 hour up to 99 hours 59 minutes in steps of 1 minutes
3. The continuous run "cont", which can be interrupted by the key "Stop/Lid"(9) (refer to figure 14).
The running time can be pre-selected with the lid open or closed.
To activate the setting of the running time, press the key
"Time"(7).
In the display "Time/Prog" (A-3) flashes the indication "m : s" or "h : m", depending on the previous setting.
To set the desired value, use the adjusting dial (4). After exceeding 59 min 50 sec the indication changes
automatically into "h : m". After exceeding 99 hours 59 min the word "cont" appears in the display "Time/Prog"
(A-3). That continuous run can only be interrupted by pressing the key "Stop/Lid" (9). The time countdown starts
assoon as the set speed is reached.
The display always shows the remaining running time. (see figure 14)
4
9
7
Figure. 14
4
A-3

EN-12 FrontierTM Centrifuge FC5513&FC5513R
3.3.3 Preselection of brake intensity and acceleration
This function is activated through the key "Accel/Decel" (6) (refer to figure 15).
By pressing the key once the word "accel" (M7) flashes in the display "Acc/Dec" (A-2). The desired acceleration
can be pre-selected by the adjusting dial (4). The value 0 is equivalent to the lowest and the value 9 to the highest
acceleration.
By pressing the key "Accel/Decel" (6) twice, the display "Acc/Dec" (A-2) indicates the word "decel"(M8). Now
thedesired brake intensity can be pre-selected by the adjusting dial (4). The value 9 is equivalent to the shortest and
thevalue 0 to longest possible brake time.
See "table 5: acceleration and deceleration times" (APPENDIX). There the acceleration and deceleration times
for the acceleration and deceleration stages 0 to 9 for permissible rotors are shown.
A-2
4
6
Figure. 15
3.3.4 Pre-selection of temperature (Only FC5513R)
This function is activated by the key "Temp/Setup" (13). After pressing this key in the display "Time/Prog" the
indication "°C" (A-4) flashes. By the adjusting dial (4) the desired test temperature can be pre-selected in steps of
1°C in a range from -20°C up to +40°C.
The value is indicated permanently in the display (figure 16) - before, during and after the run.
Please notice the respective lowest temperatures of the rotors at maximum speed!
Figure. 16
3.3.5 Pre-cooling (Only FC5513R)
If the samples are temperature-sensitive it is useful to pre-cool the centrifuge, the rotor and eventually the buckets to
the required working temperature. Therefore, insert the desired rotor and pre-set the respective temperature. By
simultaneous pressing the keys "Temp/Setup" (13) (refer to figure 17) and "Time" (6) you start the run. While
running, the unit chooses automatically a rotational speed that is equivalent to 20 % of the permitted rotational speed
of the respective rotor. After the pre-set temperature is reached you can leave the pre-cooling run with the "Stop" key
(9). Depending on the inserted rotor the pre-cooling goes between approx. 10 and 20 min.
4
13
6
A-4
M7
M8

FrontierTM Centrifuge FC5513&FC5513R EN-13
Figure. 17
3.4 Radius correction
If you use adapters or reducers, it could change the centrifugal radius of the respective rotor. In that case you can
correct the radius manually. Please proceed as follows:
Close the lid, then press the key "Time" (7) (refer to figure 16) and the key "Prog/Setup" (3) at the same time and
hold them.
In the display "Time/Prog" (A-4) the word "radius" (M9) appears. By the adjusting dial (4) you can preselect the
respective radius correction (See Table 7, APPENDIX) in steps of 0.1 cm. As soon as you have set a radius correction
the word "radius" (M9) appears. This word will be visible until you put the radius correction back to 0 again.
3
1
7
Figure. 18
3.5 Program
3.5.1 Storage of programs
You can store up to 99 runs with all relevant parameters, including the used rotors. You can use any free program
number and call it up again.
Put the needed rotor into the centrifuge. By pressing the key "Prog/Setup" (3) in the display "Time/Prog" (A-3) the
word "programm" (M10) appears. With the adjusting dial (4) you can chose the desired program number.
If a program number is already occupied, in the display "RPM/RCF" (A-1), the words "rotor" (M3) and "xx" (M4)
will appear. In case of free program numbers, 0 appears
13
6
A-4
M9
9
A-4

EN-14 FrontierTM Centrifuge FC5513&FC5513R
M3 M4
A-1
3
4
2
Figure. 19
Close the lid of the centrifuge. Now proceed as described previously to set all important run parameters. If the lid
isn'tclosed when storing the program, in the display "RPM/RCF" (A-1), the words "FirSt" and "CLOSE Lid" (see
figure 20) flashes alternately. If you want to start the run without storing the program, in the display "RPM/RCF" (A-
1), the words "First" and "PrESS StoreE" (See figure 21) flashes alternately.
Figure. 20
Figure. 21
For adaption of data press the key "Store" (2) (refer to figures 20 and 21) for approx. 1 second. If the program is
stored correctly, the word "StorE" appears in the display "RPM/RCF" (A-1). As a result, the word "programm"(M10)
disappears.
As soon as the key "Store" (2) is released, the word "programm xx" (M10) reappears –the (xx) stands for the
chosen program location.
If all program numbers are occupied, you can take an old number that is not necessary anymore and just put in the
new parameters.
3.5.2 Recall of stored programs
To recall stored programs, press the key "Prog/Setup" (3) (refer to figure 22) while the lid is already closed. Inside
the display "Time/Prog" (A-4), "programm –"(M10) appears. The desired program number can be pre-selected
with the adjusting dial (4).
In the respective displays the stored values for that program will appear.
If the wrong rotor is inside the centrifuge for the pre-selected program, in the display "RPM/RCF" (A-1), the word
"rotor" (M3) flashes. At the same time the word "FALSE" and the stored rotor number " xx" (M4) will flashing by
turns.
A-3
M10

FrontierTM Centrifuge FC5513&FC5513R EN-15
M3 M4
A-1
3
4
2
Figure. 22
3.5.3 Leaving program mode
To leave the program mode just press the key "Prog/Setup" (3) (refer to figure 22). Then inside the display
"Time/Prog" (A-3) the word "programm"(M10) appears.
Set the display to "programm--" (M10) with the adjusting dial (4).
3.6 Starting and stopping the centrifuge
3.6.1 Starting the centrifuge
You can start the centrifuge either with the "Start" key (10) (refer to figure 21) or the "Quick Spin" key (8).
By the "Start" key (10) you can start stored runs or runs with manually pre-selected parameters.
When the respective pre-selected running time has ended the centrifuge will stop automatically.
By the "Quick Spin" key (8) you can start runs, which will last just a few seconds.
By pressing the "Quick Spin" key (8) the centrifuge accelerates up to the pre-selected revolution.
In the display "Time/Prog" (A-3) the passed running time is indicated from the date of pressing the "Quick Spin"
key (8).
By releasing the "Quick Spin" key (8) the centrifuge stops and the running time is indicated until the opening of the
lid.
3
10
8
Figure. 23
3.6.2 The "STOP/Lid" key
By the "Stop/Lid" key (9) (see figure 24) you can interrupt the run at any time. After pressing the key, the
centrifugedecelerates with the respective pre-selected intensity down to stand still. After the rotor complete
stopped, press the“Stop/Lid” key will open the lid.
A-3
M10
A-3