Okamura 865JCC Installation guide

Chair
865JCC
Important Document
Assembly/
Instruction Manual
You need a Phillips Screwdriver
for assembling. Please prepare it beforehand.
Do not use an Electric driver as it may cause a
damage on the product.
Product Code (Attached to bottom of the duckboard)
Quality label (Attached to bottom of the duckboard)
Caution label (Attached on the surface of the foot step
Characters of Natural wood : This product uses natural wood
Because of the characters of natural materials, the woodgrain or color may differ one by one. And due to breathing of the materials, it may cause warpagge
or slight distortion depending on the circumstances. These features can be enjoyed as natural wood taste. This unique material increases its taste
as you use it.

Pleasecheckbeforeassembling
AboutthefixingheightofSeatandFootstep
Theheightsoftheseatandthefootstepofthischaircanbechangedin
4positions.
Pleasedeterminethebestpositionbasedontheactualheightsoftheuser
andthedesk.
Settheseatandthefootstepinthesamecombinationof
thefigureshownleft.(A,B,C,D)
Little<A<B<C<D<Big
Partslist
(Makesuretochecktheinformationbelowbeforeyoustartassembling.)
Connectingbolt Protection
Sticker
X10 X 10 X1
Note:UseaPhillipsscrewdriverforassembly.
Donotuseanelectricscrewdriverorpowertools,astheymaydamagetheproduct.
Useamanualscewdriverinstead.
1Assemblinglegframe,backboard,reinforcementbarandfootstep
Determinethepositionoftheseatandthefootstepbyreferringto"AboutthefixingheightofSeatandFootstep"firstly.
Attachthebackboard,thereinforcementbarandthefootsteptotheleftlegframewiththeconnectingbolts(ア）.
Attachtheleftlegframewiththeconnectingbolts(ア).
Actualsize
Check before assembly
（M6 x 50mm）
Seat x 1
Back board x 1
Reinforcement
bar x 1
Foot step x 1
Right leg frame
Left leg frame
Back board
reinforcement bar
Foot step
Dowel
Dowel
Left leg frame
Front
* Set the foot step as the hole comes backword.
Rigth leg
frame
* Tighten the screws loosely until installation of the seat

2Attachingtheseat
Inserttheseatpanfromthebacksdeoftheassembledframeandpushthe
L-shapemetaloftheconnectingparts(front)intothegrooveoftheseat
pan.Thentightenitwiththeconnectingbolts（ア）loosely.
TightentheUreaheadscrew(イ）tightly.Atlast,tightenalltheconnecting
bolts(ア)firmly.
3AttachmentoftheProtectionStickers
Attachtheprotectionstickers(イ)atthepointswherethechaircoｍesinto
contactwithadesk.Thestickersprotectthechairanddeskfromscratcing
eachother.Usescussorstocutoutportionssoftheappropriatesize.And
attachthemwherethedesk,chairandotheritemscomeintocontactwith
eachother.
Attachthestickerstoflatsurfaces.Ifasurfaceisdirty,wipeitclean
beforeapplyingthsticker.
Ｃｈａｎｇｅ ｏｆ ｔｈｅ ｈｅｉｇｈｔoftheSeatandtheFootstep
Theseatandthefootstepcanbechangedtheirheightsinorderto
matchtheuser'sheight.
[Changeoftheseatandthefootstep]
(1)Untightenandtakeoffalltheconnectingbolts,bindedtotheseatandthefootstep.
(2)Untighteneithersideoftheconnectingbolts,bindedtothebackboard
andthereinforcementbar.
(3)Referringto"AboutthefixingheightofSeatandFootstep",decidetheheightpostions
oftheseatandthefootstep,andinstallthematthosepositions.
*Incasethatthefootstepisnotnecessary,installittothebottomofthechair.
(4)Tightenalltheconnectingboltsfirmly.
*Causuion:Youmustinstallthefootstepinanycase.
Okamura Corporation
Internation al Sales and Marketing Div.
2-14-27, Akasaka, Minato-ku, Tokyo 107-0052 Japan
http://www.okamura.co.jp
Right leg frame
Seat
Left leg frame
Left leg frame
Right leg frame
Finished
figure
* Example for a grown child