Oki B4350 Series User manual

Flash DIMM Option Kits
OKI 8 MB FLASH DIMM KIT #70042501
OKI 16 MB FLASH DIMM KIT #70042601

Every effort has been made to ensure that the information in this document is
complete, accurate, and up-to-date. Oki Data assumes no responsibility for the
results of errors beyond its control. Oki Data also cannot guarantee that
changes in software and equipment made by other manufacturers and referred
to in this guide will not affect the applicability of the information in it. Mention
of software products manufactured by other companies does not necessarily
constitute endorsement by Oki Data.
© 2004 by Oki Data Americas, Inc. All rights reserved.
Written and produced by the Oki Data Training & Publications Department.
Please address any comments on this publication to:
Training & Publications Dept.
Oki Data Americas, Inc.
2000 Bishops Gate Blvd.
Mt. Laurel, NJ 08054-4620
For the latest product information, printer drivers, manuals, special offers, etc.,
go to http://my.okidata.com.
OKI is a registered trademark/marque déposée/marca registrada Oki Electric Industry
Company, Ltd.

Contents
Contents i
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
General Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Installing the Flash DIMM Card. . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Verifying Correct Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Installing the Software. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
PCL Macro Control Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Introduction 1
Introduction
Important!
The Flash DIMM option kits allow downloading PCL fonts and forms to the
printer. How these fonts and forms are used in printed documents depends on
the particular operating system and software application in use. This requires
programming experience and an understanding of embedding control codes,
which is beyond the scope of this software and documentation.

2 General Information
General Information
The Flash DIMM card can be used to store fonts and overlays (PCL Macros),
both of which are downloaded to the DIMM using the Storage Device Manager
(SDM) software supplied on the CD with the kit.
Fonts
Fonts in either of the following formats can be stored:
• .ttf (TrueType fonts)
• .sfp (PCL bitmap fonts)
Overlays: PCL Macros
Overlays such as
• letterheads
• logos
•forms,etc.
can be stored on the Flash DIMM, then used in printed documents.

Installing the Flash DIMM Card 3
Installing the Flash DIMM Card
Caution!
To avoid damage by static electricity or rough handling, keep the Flash
DIMM in its packaging until you’re ready to install it.
Note: The printer has only one slot in which to install an optional Flash DIMM
card or the optional Postscript emulation card.
1. Turn off the printer, and disconnect the power cord and interface cable.
2. Remove the access panel from the back of the printer:
a. Loosen the screw.

4 Installing the Flash DIMM Card
b. Remove the access panel.
3. Locate the slot:

Installing the Flash DIMM Card 5
Caution!
To avoid damage to the Flash DIMM from static electricity, ground yourself
(touch metal) before handling it.
4. Remove the Flash DIMM from its packaging.
5. Hold the Flash DIMM with the gold contact edge down and the notched
corner (1) to the right.

6 Installing the Flash DIMM Card
6. Place the DIMM in the slot and press down firmly until it snaps into place.

Installing the Flash DIMM Card 7
7. Replace the access panel:
a. Align the tabs at the bottom of the access panel with the slots in the
printer.
b. Swing the panel up and tighten the screw to secure it in place.
8. Reattach the interface cord and power cable, then turn on the printer.

8 Verifying Correct Installation
Verifying Correct Installation
1. Print a MenuMap:
a. Press ON LINE to place the printer off line.
b. Press MENU one or more times until INFORMATION MENU appears.
c. Press ITEM + one or more times until PRINT MENU MAP appears.
d. Press SELECT.
The MenuMap Prints.
2. Check the information at the top of the MenuMap. “Flash Memory” should
appear, showing the memory (8 or 16 MB) of the Flash DIMM you installed.
Note: If it does not appear, repeat the above steps and be sure the Flash
DIMM is in the correct slot and is pushed in completely at both ends
(you’ll hear it snap up into place). Then reprint the MenuMap and
check for Flash Memory again.
3. Press ON LINE.

Installing the Software 9
Installing the Software
The CD supplied with your Flash DIMM installs the Storage Device Manager
software, used to download fonts and PCL macros to the Flash DIMM:
1. Place the CD in your CD-ROM drive and wait for it to autorun.
(If the CD does not autorun, click Start →Run →Browse. Browse to
your CD-ROM drive and double-click Install.exe, then click OK.)
2. Follow the on-screen instructions to complete the installation.
3. Exit the Menu Installer.
To Open Storage Device Manager
Click Start →Programs →Okidata →Oki Storage Device Manager
→Oki Storage Device Manager.
For Information on Using Storage Device Manager
See the Reference PDF file in the root directory of the CD.

10 PCL Macro Control Codes
PCL Macro Control Codes
The following table summarizes the control codes for PCL macros.
For a complete list of control codes supported by the printer, see the Reference
PDF file in the root directory of the CD supplied with the Flash DIMM.
Command Explanation
ESC&f#Y Macro ID.
# = ID number (number you assigned to the macro when
creating it).
Note: If you don’t know the ID number, print the File List
using Storage Device Manager (click Printers →Print
File Listing). The ID number is the number which precedes
the double colon before the file name for the macro; e.g.,
for 5::logo.bin, the ID number is 5.
ESC&f#X Macro Control: Enable/Disable Macro

Oki Data Americas, Inc.
2000 Bishops Gate Blvd.
Mt. Laurel, NJ 08054-4620
Phone: [phone]
FAX: [phone]
www.okidata.com
58366601