Okina USA ECO COVERT Series Quick start guide

ESFL-X480_rev011820101
P = PAL Version
ESFL-X480
ESFL-X480P
1/3” Hi-Res. Sony CCD
480 TV Lines
3.6mm Board Lens
140° PIR Motion Sensor with Wide View Design
Halogen 300W Lighting Load Capacity (Included)
IP55 Rating
110V AC
IP55 Weatherproof housing is suitable for garage, entrance,
warehouse, corridor, parking lot, garden, street, etc. where lighting
and security is needed.
High Resolution Color CCD Camera
Model ESFL-X480 ESFL-X480P
Image Pick-up
Device 1/3” Hi-Res. Sony Color CCD
TV System NTSC PAL
Effective Picture
Elements 768(H)x494(V) 752(H)x582(V)
Horizontal
Resolution 480 TV Lines
Minimum
Illumination 0.2 Lux @ F2.0
S/N Ratio More than 48 dB
Electronic Shutter 1/60 ~ 1/100,000
sec. 1/50 ~ 1/110,000 sec.
Gamma
Characteristic 0.45
Lens 3.6mm Board Lens / F2.0
Gain Control Auto
White Balance Auto
Synchronous
System Negative Sync. Internal
Video Output 1 Vp-p Composite Video / 75 Ohms
Motion Sensor Floodlight
Voltage
Requirement
USA Plug: 110V AC
European & UK Plug: 220V AC
Also Available
Lighting Load Max 300W, J-Type
Detection Mode Pyro-Sensor
Sensor Swiveling
Angle 45° Vertical & Horizontal
Suitable Mounting Wall & Ceiling Mount
Time Adjustment 4 sec. ~ 12 min., VR Adjustable
Lux Adjustment Day ~ Night, VR Adjustable
Detection Range 16 ~ 40ft / 5 ~ 12m
140° (68°F / 20°C), VR Adjustable
Operating
Temperature -4°F ~ 104°F / -20°C ~ 40°C
Warm-up Time 30 sec.
*Specifications are subject to change without notice
One (1) ESFL-X480/ESFL-X480P with video/power cable
One (1) Halogen Lamp 300W *Refer to back page for warranty
One (1) Operational Manual
* For any returns, please include all components listed above with
original packaging in Resalable Condition. Absolutely No
Returns will be accepted if any component is missing/damaged.
FEATURES
Please read the Operational Manual
before attempting to use this product.
SPECIFICATIONS
P
A
CKAGE CON
T
ENTS
Operational Manual
Motion Floodlight Color Covert Camera
Camera
A
PPLICATIONS
By law, 110V~120V power must be
installed by a licensed electrician.
Conduit(s) may be required.
1
2
2

ESFL-X480_rev011820102
P = PAL Version
1. Consult a licensed electrician
By law, 110V~120V power must be installed by a licensed
electrician. Conduit(s) be required.
2. Installation for best results
Do not install the product in reverse or sideways to ensure the
best performance of detection range and protect the product
from dripping water. The motion sensor should not face the
moving direction of objects. This will reduce the detection
range.
3. Never point the camera toward the sun
Do not expose the lens directly to the sun or to strong light as
this may damage the pick-up device.
4. Handle this camera with care
Avoid any shock or bumping of the camera. Improper handling
could damage the camera. When replace a new halogen bulb,
take it through a soft dry cloth, do not touch it directly by
hand.
5. Requires a proper operating environment
This camera is designed for outdoor or indoor use. Install the
product on a solid base and away from heat generating
devices as the high temperature could cause wrong detection
of the motion sensor. The allowable temperature range for
operation is between -4°F ~ 104°F / -20C ~ 40C.
6. Clean the front face to the pick-up device
It is recommended that the pick-up device surface be cleaned
before lens installation or whenever the lens is changed.
Cleaning should be done by using a chamois, a very fine soft
cloth, lens tissue, or cotton tipped applicator and ethanol to
carefully remove any fingerprint or dust.
7. Check the power source voltage
The power source voltage should be within the specified
range. (Camera must meet the specifications). Camera must
be connected to a surge protector at all times.
8. Objects and liquid entry
Never push objects of any kind into this camera as this may
touch dangerous voltage points of short out parts that could
result in a fire or electric shock. Never spill any kind of liquid
on the video product.
9. Servicing
Do not attempt to service this video product by yourself as
opening or removing covers may expose you to dangerous
voltage or other hazards. Refer all service to qualified
servicing personnel.
10. Damage requiring service
Unplug this video product from the wall outlet and refer
service to qualified servicing personnel under the following
conditions:
a. When the power supply cord or plug is damaged.
b. If liquid has been spilled, or objects have fallen into
the video product.
c. If the video product has been dropped or the cabinet
has been damaged.
d. When the video product exhibits a distinct change in
performance.
11. Damage requiring service
Install bulb before powering on. Do not touch the surface of
the bulb with bare hands. Handle the bulb with a soft cloth.
12. Please follow your local privacy laws and regulations
when using covert cameras with or without audio
recording in a public setting. Manufacturer and/or
distributor are not responsible for any improper usage
of this camera.
This product is covered under warranty for one year from the date
of purchase. The warranty will automatically be voided if any of the
following occurs:
1. Camera sticker is removed
If the camera sticker is removed, we will not be able to confirm
any information regarding when and where the product was
purchased. We have no other way to verify the purchase record
without the serial number on the camera sticker; therefore, it
should not be removed.
2.
Camera is modified in any way
If the camera is scratched, damaged, or modified in a manner
not described in this manual, the warranty will be voided
immediately. It is the customer’s responsibility to keep the
camera in good condition.
3. Video or power cable is cut
The video cable and the power cable should not be tampered
with. Cutting or modifying of the cables will result in termination
of the warranty.
* The Halogen Lamp 300W is only covered under a
30-day warranty from the date of purchase.
IMPORTANT NOTE
WARRANTY
V
R ADJUSTMENT OF FLOODLIGHT