Okina USA SHB-7540DNP Quick start guide

SHB-7540DN_rev011309
Operational Manual
Day & Night Bullet Color Camera
1/3” Sony Super HAD II CCD
540 TV Lines, HQ-1 DSP
3.6mm Board Lens
0.15 Lux @ F2.0
Long life and high reliability are achieved by the
use of a CCD image device. This makes the
camera 100% solid state.
Ease of use in any application is achieved
through the small size.
IP67 Rating – Can be used for indoor/outdoor
12V DC, Max. 130mA
Camera mounting screw hole
Screw hole for fixing camera.
Power input terminal
Connect the power supply of 12V DC.
RCA terminal (Yellow)
This is a video output for connecting to a video monitor,
etc. (75Ω).
BNC video connector
This is a video connector to connect the RCA terminal to
a BNC video monitor.
Model
SHB-7540DN
SHB-7540DNP
TV System
NTSC
PAL
Image Sensor
1/3" Sony Super HAD II CCD
DSP
Sony HQ-1
Total Pixels
811(H) x 508(V)
795(H) x 596(V)
Synchronization
Internal
Resolution
540 TV Lines
Video Output
1.0Vp-p / 75Ω
Scanning System
2:1 Interlace
Gamma Correction
0.45
Minimum
Illumination
0.15 Lux @ F2.0
S/N Ratio
More than 50dB
Day & Night
Color / D&N
Auto Gain Control
Auto
Back Light
Compensation
Auto
Electronic Shutter
Speed
1/60~1/100,000s 1/50~1/100,000s
Lens
3.6mm Board Lens / F2.0, 72.5°
Power Supply
12V DC
Power
Consumption
130mA / 1.6W
IP Rating
IP67
Operation
Temperature
14˚F~122˚F / -10˚C~50˚C
Storage
Temperature
-4˚F~140˚F / -20˚C~60˚C
Storage Humidity
Max. RH90%
Dimensions
3.48”(L) x 1.04”(Ø)
88.39 (L) x 26.4 (Ø) mm
Weight
0.44 lbs / 200g
*Specifications are subject to change without notice
SHB-7540DN
SHB-7540DNP
FEATURES
Please read the Operational Manual
before attempting to use this product.
SPECIFICATIONS
PARTS AND FUNCTIONS




DIMENSIONS (Unit: mm)

SHB-7540DN_rev011309
One (1) SHB-7540DN/SHB-7540DNP Camera with
video/power cable
One (1) Mounting Bracket
Three (3) Mounting Screws
Three (3) Wall Anchors
One (1) Video Connector
One (1) Spacer
One (1) Operational Manual
*For any returns, please include all components listed above with
original packaging in Resalable Condition. Absolutely No
Returns will be accepted if any component is missing/damaged or
if any cable is cut or tampered with.
1. Never point the camera toward the sun
Do not expose the lens directly to the sun or to strong
light as this may damage the pick-up device.
2. Handle this camera with care
Avoid any shock or bumping of the camera. Improper
handling could damage the camera.
3. Requires a proper operating environment
This camera is designed for indoor and outdoor use. The
allowable temperature range for operation of this camera
is between 14˚F~122˚F / -10°C~50°C and the allowable
humidity is 90%RH maximum.
4. Clean the front face to the pick-up device
It is recommended that the pick-up device surface be
cleaned before lens installation or whenever the lens is
changed. Cleaning should be done by using a chamois, a
very fine soft cloth, lens tissue, or cotton tipped
applicator and ethanol to carefully remove any fingerprint
or dust.
5. Check the power source voltage
The power source voltage should be within the specified
range. (Camera must meet the specifications). Camera
must be connected to a surge protector at all times.
6. Objects and liquid entry
Never push objects of any kind into this camera as this
may touch dangerous voltage points of short out parts
that could result in a fire or electric shock. Never spill any
kind of liquid on the video product.
7. Servicing
Do not attempt to service this video product by yourself
as opening or removing covers may expose you to
dangerous voltage or other hazards. Refer all service to
qualified servicing personnel.
8. Damage requiring service
Unplug this video product from the wall outlet and refer
service to qualified servicing personnel under the
following conditions:
a. When the power supply cord or plug is damaged.
b. If liquid has been spilled, or objects have fallen
into the video product.
c. If the video product has been exposed to rain or
water.
d. If the video product has been dropped or the
cabinet has been damaged.
e. When the video product exhibits a distinct change
in performance.
OKINA USA products are covered under warranty for one
year from the date of purchase. The warranty will
automatically be voided if any of the following occurs:
1. Camera sticker is removed
If the camera sticker is removed, we will not be able to
confirm any information regarding when and where the
product was purchased. We have no other way to verify
the purchase record without the serial number on the
camera sticker; therefore, it should not be removed.
2. Camera is modified in any way
If the camera is scratched, damaged, or modified in a
manner not described in this manual, the warranty will
be voided immediately. It is the customer’s responsibility
to keep the camera in good condition.
3. Video or power cable is cut
The video cable and the power cable should not be
tampered with. Cutting or modifying of the cables will
result in termination of the warranty.
PACKAGE CONTENTS
CAUTION
WARRANTY