Oklahoma Sound Aristocrat NPS 6010-MY/LWM-7 User manual

OklahOma SOund COrpOratiOn
OPTIONAL / ADDITIONAL EQUIPMENT
ASSEMBLY MANUAL
ARISTOCRAT
Sound Floor Lectern
MODEL #6010
BRASS READING LAMP / #BRL
Attach an elegant brushed brass reading lamp to
the reading table of your new Speaker Stand. Not
only will you shed light on the subject, but you will
add pizzaz to your new stand.
RECHARGEABLE BATTERY / #PS12V
Connect this 12V 5 amp rechargeable battery
pack with included cable to any of our lecterns
for battery power. 20 hour life. Lecterns recharge
battery overnight.
ARISTOCRAT CONTOUR
FLOOR LECTERN / #600
The perfect lectern for the most demanding,
upscale look in your conference, training
and formal meeting rooms. Contoured
style with radius curves. Available in three
woodgrain thermofused melamine laminate
on MDF. Two built in shelves and our side
mounted slide-out shelf for A/V presentation
equipment. Accented by attractive T-mold
edging. Moves eortlessly on four easy roll
castors, two locking. Ready to assemble.
Dimensions: 23" W x 46½" H x 16" D
Walnut, Lt. Oak, Med. Oak, Mahogany.
ARISTOCRAT CONTOUR
TABLE TOP LECTERN / #60
Same upscale styling as its full oor sister, but
in an easy-go table top version. Move this at-
tractive, aordable lectern from room to room
and keep your notes in order and your audi-
ences wowed. Made of thermofused laminate
in four color selections with T-mold edging.
Protective non marring glides included.
Assembly required.
Dimensions: 25" W x 15" H x 20" D
Walnut, Lt. Oak, Med. Oak, Mahogany
For these products please contact your dealer
or Oklahoma Sound Corp.
OKLAHOMA SOUND CORP.
149 Entin Road, Clifton, NJ 07014
Tel [phone] • Fax [phone]
www.oklahomasound.com • email: inf[email protected]
#BRL #PS12V
#600
#60

OklahOma SOund COrpOratiOn ARISTOCRAT SOUND FLOOR LECTERN: Model 6010
2 7
INTRODUCTION
Aristocrat Sound lectern - Model 6010
Perfect for the smallest to largest venues. Executive style podium includes
50 watt multimedia amplier with two built in 8" speakers surrounded by
gold appointments. Includes Microphones, Holders, Digital Timepiece and
rolls on four casters. For audiences up to 2,500 people. Assembly required.
Colors: Walnut, Light Oak, Med. Oak, Mahogany/Black Edging
Dimensions: 25¼" W x 46" H x 20¼" D.
ASSEMBLY TIPS
• Do not use a sharp instrument such as a knife or a screwdriver to open the
packaging, as this may scratch or possibly damage the unit.
• All assembly should be done on a clean protected surface such as carpet
or the like.
• Make sure that you have all the required parts. A list of all the parts
is included.
• Read instructions carefully and follow diagrams to ensure easy and
correct assembly.
CARE OF YOUR CABINET
• All exterior and interior exposed surfaces are melamine covered as well as
edges in matching patterned melamine material. To refresh the appear-
ance, wipe the surface with a cloth soaked lightly in furniture oil. Avoid
speaker grill area Your cabinet will look as good as new.
TECHNICAL SPECIFICATIONS
Manufacturers Warranty
Our lectern undergoes the most rigid and exacting tests for superior quality and performance before
leaving the factory. Our lectern is made in America by American craftsmen. Oklahoma Sound
Corporation warrants this product to be free from defective material and workmanship for two years
from the date of resale by an authorized Oklahoma Sound distributor. Oklahoma Sound will replace
defective parts and repair malfunctioning products under this warranty when the defect occurs under
normal installation and use, provided the unit is returned to our factory via prepaid transporta-
tion after direct authorization and approval by Oklahoma Sound. is warranty provides that
examination of the returned product must disclose in our judgement, a manufacturing defect. is
warranty does not extend to any product which has been subject to misuse, neglect, accident, improper
installation, or where the serial number has been removed or defected and is given in lieu of any other
warranty implied or expressed and will not cover any consequential damages.
Power Output .......50W RMS at 10% THD
Mic ............................Electret Condenser Mic (2)
Aux............................150 mV>220K
Frequency ..............100HZ-25KHZ
Response ................+ 3dB
Power Supply....110-120V ohms DC 10.8 12V
Fuse ......................2A normal
Output.................8 ohms
Accessories ........Handheld mic; clip-on mic;
gooseneck; Shockmount
mic holder; digital clock
700 Series Amplier Operating Instructions
Operating Precautions
Before operating the amplier, be sure you fully understand all instructions and
features of the amplier. DO NOT turn amplier on until all input and output
connections have been made. NEVER replace fuses unless power is o.
Microphone Input Connection
The microphone input accepts ¼" phone jack. Do not position microphone next
to or facing speakers. This may cause acoustic feedback.
Auxiliary Input
One auxiliary input is provided for radio tune; tape recorder, CD player or multi-
media equipment. Output level is adjusted by the auxiliary volume control.
Tone/Equalization Controls
The Low and High frequency controls are similar to the bass and treble controls
found on most stereo systems. Optimum tone is achieved by rst setting both
knobs halfway; adjust Low and High frequency controls to suit environment.
Power Supply 12V DC Operation
Connect a 12 volt rechargeable battery 5 amp (not included) to the battery
input connector located on the panel of the amplier (using 6' battery cable).
Be sure that the positive pole of battery is connected to the white wire terminal
(+) and the negative pole to the Brass wire (-). When lectern is plugged into a
standard wall outlet, the battery will automatically recharge. Green indicator
light illuminates during recharge mode.
Precautions
• Set Mic volume control on lowest when turning unit on.
• Ensure correct polarity for D.C. supply connections.
• Reverse connections will blow the fuse and may damage internal circuitry.
• Always replace fuse with specied rating.
Removal and Installation of Amplier
If your amplier has to be removed for servicing — follow these simple steps:
1) Disconnect A/C wall plug.
2) Remove 4 side screws two on each side panel under amp top.
3) Disconnect speaker wire at rear of amplier.
4) Pack it into a strong box with ample cushioning and return to factory
5) To install new amplier reverse the above procedure.

OklahOma SOund COrpOratiOn ARISTOCRAT SOUND FLOOR LECTERN: Model 6010
6 3
4) Now apply Panel C to the semi assembled unit. Be sure to align the cam
bolts to the holes on both Panel B and Panel E. Be sure that Panel F is se-
curely in groove. Tighten cams. (Diagram C)
5) Screw the corner braces on the bottom Panel F into Panels A, B and C.
6) Connect the plug coming out of the speakers on Panel B to the plug coming
out of the back of the amp. Fit the amp between the two sides and bring
the amp up until it reaches the
cleats (wood stub) then from the
bottom of the amp screw in four
screws. (Diagram D)
7) Once again go over all the cams
and check to make sure the lec-
tern is sturdy.
8) Screw on gooseneck mic holder
and install microphone for
sound use.
Congratulations! You have success-
fully assembled your lectern, which
if
cared for correctly should give you
long and satisfactory usage.
Diagram "C"
Diagram "D"
Left Side Panel Right Side Panel
Front Panel
ASSEMBLY PARTS
Top
(Reading Surface)
Shelf Bottom
Tools Required
#2 Phillips Head
Screwdriver
Hammer
Cam Lock Assembly
(1) Gooseneck
............................................
(1) Hand-held
Condenser Mic
............................................
(1) Tie-Clip
Mic
..........................
(2) Locking Casters
........................................ (14) Cams
..........................
(14) Cam Bolts
..........................
(36) #8
½" Phillips
Screw
..........................
(2) Non
Locking
Casters
.............................
(4) Corner Braces
.....................................
(1) Amplier
Series 700
................................................................
A
B
C
E
DF

OklahOma SOund COrpOratiOn ARISTOCRAT SOUND FLOOR LECTERN: Model 6010
4 5
INSTALLATION OF HARDWARE
1) Lay out the wood panels as shown in Diagram A (make sure the factory drilled
holes are facing upwards). You can determine the top of the front panel by iden-
tifying the T-molding.
2) Identify the holes numbered "1" in Diagram A. Screw the bolts into the pre-
drilled holes with a #2 Phillips-head screwdriver. Be sure to tighten the screws all
the way. Note: Be careful not to over-tighten the bolts as this will strip the wood!
3) Insert the cams in the larger holes as shown on diagram. MAKE SURE THE AR-
ROW ON THE CAM IS POINTING TO CLOSEST EDGE AND ALIGNED WITH THE
HOLE ON THE EDGE.
5) On Panel F, screw in the four casters. The locking casters should be screwed into
the bottom closest to the T-molded contoured edge. The second pair of non-
locking casters should be screwed in closest to the unnished edge.
ASSEMBLY OF LECTERN
It is important that the instructions on the assembly are followed carefully
1) The rst step of assembly will be to align the holes on Panel B edges with the
three cam bolts on Panel A, tighten cams by turning clockwise until locked.
2) Next will be Panel D and Panel E. Make sure the cams on Panel D and Panel E
face the bottom of the lectern. The two highest bolts align with the two holes
on the edge of Panel D (these holes reach until the cams). The two bolts in
the center of Panel A will align with the two holes on the edge of the shelf.
Gently push the shelves down on to the cam bolts until the shelf is complete-
ly on the right side panel. Tighten.
3) Take Panel F, with the casters facing the bottom of the unit insert panel into
the groove, make sure that the panel is all the way in the groove. (Diagram B)
Diagram "B"
Diagram "A"
A
B
C
E
D
F
Front Panel
Top