Oklahoma Sound A/V Cart User manual

OklahOma SOund COrpOratiOn
OPTIONAL EQUIPMENT
Additional Units (sold separately)
TABLE TOP LECTERN / #22
This versatile, portable table top lectern,
can be used on its own or as a oor
lectern with the optional base (sold sepa-
rately). ⁄" stain and scratch resistance
thermofused melamine laminate on MDF.
Paper/book stop included.
Dimensions: 23¾" W x 13¾" H x 19⁄" D
Available Color Options
Medium Oak • Light Oak • Mahogany • Walnut
BRASS READING LAMP / #BRL
Attach an elegant brushed brass reading lamp
to the reading table of your new Speaker Stand.
Not only will you shed light on the subject, but
you will add pizzaz to your new stand.
For these and other OSC accessories, please contact your dealer, or:
OKLAHOMA SOUND CORP.
149 Entin Road, Clifton, NJ 07014
Tel [phone] • Fax [phone]
www.oklahomasound.com • email: [email protected]
FULL FLOOR LECTERN / #222
Attractive and durable lectern made of ⁄"
stain and scratch resistant thermofused
melamine laminate on MDF. Full sized
reading surface, shelf and paper/book
stop built in. Floor glides provided.
Dimensions: 23" W x 46½" H x 16"D
ASSEMBLY MANUAL
A/V Cart
[Combo Lectern Base]
MODEL #112

OklahOma SOund COrpOratiOn
INTRODUCTION
The model #112 Combo Lectern Base - A/V Cart Con-
verts the TABLE TOP to a FULL FLOOR lectern or use
as an A/V cart for your presentation equipment. "
stain and scratch resistance thermofused melamine
laminate on akeboard. Includes storing shelf and four
easy roll casters; two locking.
Dimensions: 21⁄" W x 33¾" H x 17½" D.
Manufacturers Warranty
Our lectern undergoes the most rigid and exacting tests for superior quality
and performance before leaving the factory. Our lectern is made in America
by American craftsmen. Oklahoma Sound Corporation warrants this prod-
uct to be free from defective material and workmanship for two years from
the date of resale by an authorized Oklahoma Sound distributor. Oklahoma
Sound will replace defective parts and repair malfunctioning products under
this warranty when the defect occurs under normal installation and use,
provided the unit is returned to our factory via prepaid transportation after
direct authorization and approval by Oklahoma Sound. is warranty
provides that examination of the returned product must disclose in our
judgement, a manufacturing defect. is warranty does not extend to any
product which has been subject to misuse, neglect, accident, improper instal-
lation, or where the serial number has been removed or defected and is given
in lieu of any other warranty implied or expressed and will not cover any
consequential damages.
A/V CART: Model 112
5) Four casters are supplied, two with brakes and two with-
out brakes. The casters are attached to a metal channel
called a u-clip. About an inch into the wood, at the four
bottom edges there are pre-drilled holes, these are
there for the purpose of screwing the casters in place.
P.S. Be sure to attach the two brake casters towards the
front of cart (front panel) as shown in (Diagram F)
Diagram "F"
27
6) Once again go over all the cams and check to make sure
the cart is sturdy.
Congratulations! You have successfully assembled your
cart, which if cared for correctly should give you long and
satisfactory usage (Diagram G).
Diagram "G"
Brake Casters

6 3
OklahOma SOund COrpOratiOn A/V CART: Model 112
3) Align the bolts on the front of Panel B sides with the
cams on both side panels, tighten cams (Diagram D).
Notice Panel B is about an inch taller that the rest of the
cart this is needed for the optional model #22 see back
page.
4) Stand the cart up (the bottom can be identied by the
small drilled holes about an inch from the bottom side
edges). Taking the top Panel D of the cart with the in-
stalled cam-bolts facing down, align bolts with holes
on the top edges. Once they are in place apply gentle
pressure on the top shelf until it lies at on all of the top
edges, then tighten cams. (Diagram E)
Diagram "D"
Diagram "E"
ASSEMBLY INSTRUCTIONS
Assembly Tips
• Do not use a sharp instrument such as a knife or screwdriver
to open the packaging, as this may scratch or possibly dam-
age the unit.
• All assembly should be done on a clean protected surface
such as carpet or the like.
• Make sure that you have all the required parts. A list of all
the parts is noted below.
• Read the instructions carefully and follow the diagrams to
ensure an easy and correct assembly.
Tools Required
#2 Phillips Head Screwdriver
Hammer
Parts
14 Cams..................
14 Cam Bolts ...............................
4 Casters...................
1 Top Panel
1 Front Panel
1 Right Panel
1 Left Panel
1 Shelf
Example of Cam Lock Assembly

4 5
OklahOma SOund COrpOratiOn A/V CART: Model 112
INSTALLATION OF HARDWARE
1) Lay out the wood panels as shown below in gure "A" (make
sure the factory drilled holes are facing upwards).
2) Identify the holes numbered "1" in Diagram A. screw the
bolts into the holes with the #2 Phillips Head screwdriver. Be
sure to tighten the screws all the way. Note: Be careful not to
over-tighten the bolts as this will strip the wood.
3) The cams should be inserted in the larger holes as shown
on the Diagram "A". MAKE SURE THE ARROW ON THE CAM IS
POINTING TO THE CLOSEST EDGE AND ALIGNED WITH THE
HOLE ON THE EDGE.
Diagram "A"
ASSEMBLY OF LECTERN
It is important that the instructions on the assembly are
followed carefully
1) Panel E the rst piece of equipment that will be in-
stalled will be the shelf. Make sure the cams will face
the bottom of the lectern. The two bolt in the center
of Panel A (the right hand panel) will align with the
two holes on the edge of the shelf Panel E (these holes
reach until the cams) gently push the panel down on to
the cam bolts until the panel is completely on the right
side Panel A. Tighten the cams by turning clock-wise
until locked (Diagram B).
2) Apply Panel C to the second side of the shelf. Tighten
cams (Diagram C)
Diagram "B"
Diagram "C"
A
B
C
E
D