OLG PLANTATION Series User manual

Plantation Assembly Instructions 1
PLANTATION
Assembly Instructions

Plantation Assembly Instructions
2
Plantation
Extendable Rails

Plantation Assembly Instructions 3
STEP 3: Use the center as reference to position both ends back into the center rail
symmetrically.
STEP 1: Unscrew end rails and remove. STEP 2: Find the middle point of the center rail and screw the bracket.
STEP 4: Screw the end rails to the center rail once achieved the desired length.
Screw to the structure spigots.
1/2
1/2
Plantation
Extendable Rails

Plantation Assembly Instructions
4
Plantation
Assembly Instructions - Round Tables 600D

Plantation Assembly Instructions 5
Plantation
Assembly Instructions - Round Tables 600D
STEP 1: Align the legs at even spacing on the worktop, with the top plate being no
closer than 5 mm from the edge of worktop. Mark each leg location for easy
fixing in step 2.
STEP 3: Turn the table over.
STEP 2: Fix the leg to the worktop using 4 x 23 mm self-tapping screws per leg.

Plantation Assembly Instructions
6
Plantation
Assembly Instructions - Round Tables 900D

Plantation Assembly Instructions 7
Plantation
Assembly Instructions - Round Tables 900D
STEP 3: Fix the leg to the worktop using 4 x 23 mm self-tapping screws per leg.
STEP 1: Fix 1x angle brack to each leg using 2 x M12 bolts. STEP 2: Align the legs at even spacing on the worktop, with the top plate being no
closer than 5 mm from the edge of worktop. Mark each leg location for easy
fixing in step 3.
STEP 4: Turn the table over.

Plantation Assembly Instructions
8
Plantation
Assembly Instructions - Round Tables 1050D

Plantation Assembly Instructions 9
Plantation
Assembly Instructions - Round Tables 1050D
STEP 3: Fix the leg to the worktop using 4 x 23 mm self-tapping screws per leg.
STEP 1: Fix 1x angle brack to each leg using 2 x M12 bolts. STEP 2: Align the legs at even spacing on the worktop, with the top plate being no
closer than 5 mm from the edge of worktop. Mark each leg location for easy
fixing in step 3.
STEP 4: Turn the table over.

Plantation Assembly Instructions
10
Plantation
Assembly Instructions - Round Tables 1200D

Plantation Assembly Instructions 11
Plantation
Assembly Instructions - Round Tables 1200D
STEP 3: Fix the leg to the worktop using 4 x 23 mm self-tapping screws per leg.
STEP 1: Fix 1x angle brack to each leg using 2 x M12 bolts. STEP 2: Align the legs at even spacing on the worktop, with the top plate being no
closer than 5 mm from the edge of worktop. Mark each leg location for easy
fixing in step 3.
STEP 4: Turn the table over.

Plantation Assembly Instructions
12
Plantation
Assembly Instructions - Round Tables 1500D

Plantation Assembly Instructions 13
Plantation
Assembly Instructions - Round Tables 1500D
STEP 3: Align frame with worktop and fix down using 4 x 23 mm screws per leg and
4 x 70 mm screws for the rails.
STEP 1: Fix 1x rail receiver to each leg using 2 x M12 bolts.
Fix 2x rail receivers to the centre rail using 2 x M12 bolts.
STEP 2: Connect centre rail, 2x short rails, 4 x legs together as shown.
STEP 4: Use 2 persons to turn the table over to be the correct way up.

Plantation Assembly Instructions
14

Plantation Assembly Instructions 15

Plantation Assembly Instructions
16
Plantation
Assembly Instructions - Meeting Table 4 Leg

Plantation Assembly Instructions 17
Plantation
Assembly Instructions - Meeting Table 4 Leg
STEP 3: Assemble the rails to the end legs and set rail length.
40 mm less than worktop
STEP 1: Assemble 2x end leg frames to the legs. Total 6 x M12 per leg. STEP 2: Assemble the rail receivers to the crossbar.
STEP 4: Fix worktop to frame using 4 x 23mm screw per leg, 1 x 23mm screw per rail.

Plantation Assembly Instructions
18
Plantation
Assembly Instructions - Meeting Table 6 Leg

Plantation Assembly Instructions 19
Plantation
Assembly Instructions - Meeting Table 6 Leg
STEP 4: Assemble the rails to the end legs and set rail length.
40 mm less than worktop
equal
measurement
equal
measurement
STEP 1: Assemble 2x end leg frames to the legs.
Total 6 x M12 per leg.
STEP 2: Assemble the rail receivers to the crossbar. STEP 3: Assemble the mid leg using bolts provided
in the spreader bar kit. Mount the rail to the
centre mounting point.
STEP 5: Fix worktop to frame using 4 x 23mm screw per leg, 1 x 23mm screw per rail.

Plantation Assembly Instructions
20