OLT Gardener's Shed GAR88-FJ-METAL User manual

8x8 Gardener’s Shed -
Metal Roof - Finger Jointed Siding
- Assembly Manual
Version 1.3
July 22, 2021
In the event of a missing or broken piece, simply call the Outdoor Living Today Customer
Support Line @ 1-888-658-1658 within 30 days of the delivery of your purchase. It is our
commitment to you to courier replacement parts, free of charge, within 10 business days of
this notification. Replacement parts will not be provided free of charge after the 30 day grace
period.
Some of the safety and usage measures you may wish to consider include:
-snow load ratings vary by geographical location. If heavy or wet snowfall occurs, it is advisable to sweep the
snow off the roof(s).
-if the product is elevated, any structural and building code requirements are solely the customer's
responsibility, and should be abided by.
-in high or gusty wind conditions it is advisable to keep the structure securely grounded.
-have a regular maintenance plan to ensure screws, doors, windows and parts are tight.
Customer agrees to hold Outdoor Living Today Partnership and any Authorized Dealers free
of any liability for improper installation, maintenance and repair.
Toll Free 1-888-658-1658 www.outdoorlivingtoday.com [e-mail]
Page 1
Thank you for purchasing
an 8x8 Gardener’s Shed.
Please take the time to
identify all the parts prior
to assembly.
Safety Points and Other Considerations
Our products are built for use based on
proper installation and normal residential use,
on level ground. Please follow the instruction
manual when building your shed and retain
the manual for future maintenance purposes.
STOCK CODE #
GAR88-FJ-METAL

What to do before my Shed arrives?
Become familiar with this assembly manual and determine if you can•
complete the project yourself or will require a professional contractor.
Clear the construcon area and ensure a clear pathway for delivery when•
the freight company arrives. Remove all debris: roots, grass, rocks, etc.
Excavate the site. Contact your local ulies company to ensure there are no•
gas or electric lines buried in the area before digging.
Decide on the type of foundaon you will be using:•
 Concrete slab, or
 46 inches of crushed gravel with paver stones or 4x4 stringers.
You can find the footprint for your shed on Page 3 of your Assembly Manual.
If doing the assembly yourself, have all the necessary tools ready to go and in•
working condion. A list of required tools can be found aer the parts list.
One helper is recommended to assist in construcng your shed.•
It generally takes two people over two days to assemble a shed. If you’re
hiring a contractor, their rate should be in line with that duraon of work.
Toll Free 1-888-658-1658 www.outdoorlivingtoday.com [e-mail]
Page 2

Foundation Types for 8x8 Garden Shed
Concrete Slab Foundation:
- Slab must be at least the same size as assembled floor frame (91” x 96”) or larger.
- 6” Deep foundation.
- 1.2 Cubic Yards of concrete required.
- A concrete slab will have the longest durability out of your foundation options.
Once level, a concrete slab is the easiest surface to build on.
Gravel with 4x4 Pressure Treated Stringers:
- Excavate at least 6” deep, and 6” wider than floor frame on each side.
- 1.5 Cubic Yards of gravel required, approximatley 14 wheelbarrows.
- 5 - 4x4 Pressure Treated Stringers 8’ long required.
- Evenly spaced, with one at each end of floor frame.
Saves money on materials, easy to level and work with.
Gravel with Patio Paver Stones:
- Excavate at least 6” deep, and 6” wider than floor frame on each side.
- 1.5 Cubic Yards of gravel required, approximately 14 wheelbarrows.
- 25 patio pavers (8” x 8” or larger).
- Center patio paver stones underneath floor runners and underneath seams in floor joists.
Patio paver stones are widely available from most landscape stores.
96”
91”
96”
91”
6” Deep
108”
103”
5 - 4”x4”x96”
25 Patio Stones
Floor Frame
Concrete Foundation Completed Foundation
18 3/8”
Gravel Foundation Gravel Foundation with treated stringers Completed Foundation
Gravel Foundation Gravel Foundation with Patio Pavers Completed Foundation
108”
103”
Shed Front Shed Front Shed Front
Shed Front Shed Front Shed Front
Shed Front Shed Front Shed Front
Toll Free 1-888-658-1658 www.outdoorlivingtoday.com [e-mail]
Page 3

Thank you for purchasing our 8x8 Gardener’s Shed.
Please take the time to identify all the parts prior to assembly.
1. Floor Section
Floors
2 - 45 1/2” x 75” - Floor Joist Frames - Large
2 - 45 1/2” x 21” - Floor Joist Frames - Small
4 - 1 1/2” x 3 1/2” x 71 7/8” - Center Floor Joists - Unattached
5 - 1 1/2” x 3 1/2” x 31” - Floor Runners Short
5 - 1 1/2” x 3 1/2” x 60” - Floor Runners Long
2 - 45 3/8” x 74 7/8” - Plywood Floor - Large
2 - 45 3/8” x 20 7/8” - Plywood Floor - Small
2. Wall Section
Main Wall Panels
6 - 45 1/2” x 75” - Solid Wall Panels (Bottom Wall Plates unattached)
6 - 1 1/2” x 2 1/2” x 45 1/2” - Bottom Wall Plates
1 - 45 1/2” x 75” - Window Wall Panel
1 - 12” x 73” Narrow Wall Panel
Door Headers
1 - 1 1/2” x 3 3/8” x 73” Door Jamb
1 - 2” x 3 3/8” x 45 1/2” - Door Header (Dado cut on edge)
Top Wall Plates & Gables
6 - 3/4” x 2 1/2” x 32” - Front & Rear Top Plates
(2 pieces angle cut on end, 1 piece straight cut both ends)
2 - 3/4” x 2 1/2” x 86” Side Top Plates (Angle cut on edge)
4 - Gable Half Walls - Triangular Shaped
3. Rafter and Roof Section
Rafter Assembly
2 - 3/4” x 4 1/2” x 57 1/2” - Roof Ridge Boards Long
2 - 3/4” x 4 1/2” x 33 1/2” - Roof Ridge Boards Short
12 - 1 1/2” x 3 1/2” x 56 1/2” - Roof Rafters (angle cut ends)
4 - 1/2” x 4 1/2” x 45 1/2” - Soffits
2 - 3/4” x 3 1/2” x 72” - Roof Gussets (angle cut on ends)
Roof
16 - 3/4” x 3 1/2” x 48 1/4” - Roof Battens
12 - 3/4” x 1 1/2” x 14” - Batten Spacers
6 - 39” wide x 61” long - Metal Roof Panels
2 - 60” long - Metal Ridge Caps
Several Pcs - Foam Enclosures
4. Trim & Miscellaneous Section
Bottom Skirting
8 - 1/2” x 4 1/2” x 45 1/4” - Bottom Skirting (FJ)
Corner & Sidewall Trim
2 - 1/2”x 2 1/2” x 79” - Narrow Trim Side Wall
4 - 3/4” x 2 1/2”w x 75” - Filler Trim
4 - 1/2” x 5 1/2”w x 82” - Wide Corner Trim
4 - 1/2” x 3 1/2”w x 79” - Corner Trim
2 - Metal Drip Edge
2- 1/2” x 4 1/2”w x 43 3/8” - Horizontal Gable Trim Front
2 - 1/2” x 4 1/2”w x 43 3/8” - Horizontal Gable Trim Rear (FJ)
3 - 1/2” x 2 1/2” x 77 1/2” - Narrow Trim (Front and Rear Wall)
4 - 1/2” x 1 1/2” x 45 1/4” - Top Wall Trim (FJ)
Facia Trim
4 - 3/4” x 2 1/2” x 52 1/2” Facia/Roof Nailing Strips
4 - 3/4” x 3 1/2” x 58” - Front and Rear Facia (Angle cut on ends - 2
right / 2 left)
4 - 3/4” x 3 1/2” x 49 1/4” - Side Facia
2- Pentagon Facia Plates
2 -Side Facia Detail Trim Plates - Smaller
2 - Horizontal Gable Trim Detail Plates - Larger
Door
1 - 31 1/2” x 72” - Door
2 - 1/2” x 2 1/2” x 72” - Interior Vertical Door Stops
1 - 1/2” x 2 1/2” x 36” - Interior Top Horizontal Door Stop
**Miscellaneous Pieces
1 - Window Insert
1 -Window Trim Pkg - (1-24 1/16” angle cut / 3 -23” straight cut )
1- Flower Box Kit
1 pc - Spare Wall Siding
2 pcs - Spare Shingles- use to shim door, etc
23-24
Steps
Steps
25-32
Steps
61
62-70
Steps
12-22
1-11
33-45
75-78
Parts List - Page 2
46-60
71-74
79-82
Toll Free 1-888-658-1658 www.outdoorlivingtoday.com [e-mail]
Page 4

8x8 GARDENER - METAL - HARDWARE SHEET
2 1/2”
2”
1 1/4”
3/4”
2”
3/4”
Tee Hinge x3 Pull Handle Ridge Board
Connector x 2
Silver
Square Drive Bit
Hardware Kit (Provided)
Safety Glasses Work Gloves
Safety Equipment Required (Not Provided)
Ladder
Screw Gun/Drill Tape Measure
Hammer Wood Clamp
Level Pliers
Tools Required (Not Provided)
1/8” Drill Bits
Black Barrel
Bolt
1 1/2”
Finishing
Black Headed
Black Headed
x 228
x 120
x 22
x 267
x 18
x 10
x 308
x 1
Single Rafter
Bracket x 4
Double Rafter
Bracket x 2
Silicon Caulking (2)
x 48
1/4”x 2”
Metal Roof Screw
Metal Roof
Hangar x 3
x 1
1/4” Nut Driver
Toll Free 1-888-658-1658 www.outdoorlivingtoday.com [e-mail]
Page 5

Regular Maintenance & Tips to prolong the life of your shed.
Before/During Assembly:
1.) Paint each face and edge of your plywood floor with a latex exterior paint.
2.) Caulk wall seams if gaps appear.
3.) Caulk around window framing.
4.) Caulk perimeter between floor plywood and bottom wall plate.
5.) Caulk channels in lap siding at the top of your door above the trim, just a drop in each channel.
6.) Caulk edge of door threshold.
7.) Optional: Install a Sill Gasket between floor runners and foundation.
8.) Optional: Install an 8” strip of roofing paper below Cedar Ridge Caps for Cedar Roof Sheds.
Routine Maintenance:
- Routinely check all fasteners are tight (ex. Door Hinges, Nails)
- Brush off dirt from walls.
- Brush off snow from roof regularvly.
- Routinely remove needles and leaves from roof.
Painting/Staining
- Your cedar shed, if left untreated, will weather to a silvery grey colour.
- Painting or staining your structure is highly recommended and will prolong the life of your shed.
- You do not need to wait to paint or stain your shed, the wood in your kit has been dried and can be
—stained or painted immediately.
- Consult your local paint store for the best paint or stain for cedar.
- Optional: stain the inside of your shed. (Note: this will remove the fresh cedar smell.)
1. 2. 3.
4. 5. 6.
7.
Sill Gasket
Floor Joists
Floor Runner
Foundation
8.
Floor Plywood
Wall Panel
Small gap between
bevel siding and
window trim
Dab of caulking
Strip of roofing paper over
apex of roof panels
Toll Free 1-888-658-1658 www.outdoorlivingtoday.com [e-mail]
Page 6

A. Floor Section
Plywood Floor
Large (2)
Floor Joist
Frames
Large (2)
Floor Runners (10)
Plywood Floor
Small (2)
Exploded view of all parts necessary to complete
Floor Section. Identify all parts prior to starting.
Note: Floor Footprint is 96” wide x 91” deep.
Concrete Pad
(optional foundation method)
Floor Joist
Frames
Small (2)
Flush
with
framing
1. Lay out Large Floor Joist Frame and
2 Floor Joists as illustrated above.
Position Joists equally in Floor Joist
Frame. Use Small Floor Joist Frame as a
template to determine joist position.
Position Joist so flush with framing.
Parts (Steps 1 - 6)
Floor Joists
(1 1/2” x 3 1/2” x 71 7/8”) x 4
Floor Joist Frames - Large
(45 1/2” x 75”) x 2
Floor Joist Frames - Small
(45 1/2” x 21”) x 2
Hardware (Steps 1 - 6)
S1 - 2 1/2” Screws
x 46 total
Toll Free 1-888-658-1658 www.outdoorlivingtoday.com [e-mail]
Page 7

5. Complete all large and small frame
attachments. Screw each completed
section together with 8 - 2 1/2” screws.
6. When completed, your floor footprint
should be 96” wide x 91”deep.
91”
3. Lay out Floor Joist Frames as
illustrated at left. There are 2 larger and
2 smaller Frame Sections. The Footprint
for the floor when attached together will
be 96” wide x 91” deep.
4. Attach each large and small floor joist frame
together with 6 - 2 1/2” screws per section.
2. When correctly positioned, attach each Joist with 4 - 2 1/2” screws (2 per end).
You can find the
Square Drive Bit
for the screws in
with the Hardware
Kit Bag.
Front 96”
Door goes
on 96” side
Toll Free 1-888-658-1658 www.outdoorlivingtoday.com [e-mail]
Page 8

Note: The floor will be flipped over and floor
runners will sit on your foundation. It is
important to note that having a level
foundation is critical. Choosing a foundation will
vary between regions. Typical foundations can
be concrete pads or patio stones positioned
underneath the floor runners.
9. With Floor Runners attached, carefully flip
the floor over and place on your foundation.
Caution: you will need 2 people to assist you.
Be careful when laying floor down not to bend
or twist floor. When in place, level floor
completely.
Concrete Slab
Foundation
Foundations
8. Complete all Floor Runners.
Front
plywood
pushed together
at seams.
7. Attach Floor Runners to completed floor frame.
There are 2 Floor Runners per 91” side and 5 complet-
ed runners in total. Use 3 - 2 1/2” screws per Floor
Runner. Make sure Runners are flush with outside,
front and rear floor framing but not overhanging.
Parts (Steps 7 - 9)
Floor Runner Short
(1 1/2” x 3 1/2” x 31”) x 5
Floor Runners Long
(1 1/2” x 3 1/2” x 60”) x 5
Hardware (Steps 7 - 9)
S1 - 2 1/2” Screws
x 30 total
Parts (Steps 10 - 11)
Floor Plywood Small
(5/8” x 45 3/8” x 20 7/8”) x 2
Floor Plywood Large
(5/8” x 45 3/8” x 74 7/8”) x 2
Hardware (Steps 10 - 11)
S2 - 1 1/4” Screws
x 46 total
10. Position Plywood Floor pieces (4) on top of
completed floor joists. Plywood is cut slightly small-
er than floor framing. Keep plywood seams tight.
Door goes
on 96” side
Toll Free 1-888-658-1658 www.outdoorlivingtoday.com [e-mail]
Page 9

Hint: Use a chalk
line to mark location
of floor joists to
determine screw
placement.
11 . With Plywood
positioned correctly on
floor framing, attach
with 1 1/4” screws. Use
screws every 16”.
B. Wall Section Exploded view of all parts necessary to
complete the Wall Section. Identify all
parts prior to starting.
Window Wall
Panel (1)
Side Top Plates
(2 per side)
Angle cut on edge
Front and Rear Top
Plates (3 per side)
2 Angle cut on 1 end and 1
square cut.
Gable Walls
(4)
Door Jamb
Narrow Wall Panel
(12” wide)
Solid Wall
Panel (6)
Door Header
Bottom Wall Plate
12. Starting with Solid Wall Panels, carefully
lay panel face down. Position and attach Bottom
Wall Plate to bottom of wall studs of each wall
panel with 3 - 2 1/2” screws. Position so plates
are flush with framing. Note: some Bottom Wall
Plates may already be attached to some walls.
Parts (Step 12 )
Solid Wall Panels
(45 1/2” x 75”) x 6
Bottom Wall Plates
(1 1/2” x 2 1/2” x 45 1/2”) x 6
Hardware (Step 12 )
S1 - 2 1/2” Screws
x 36 total
Toll Free 1-888-658-1658 www.outdoorlivingtoday.com [e-mail]
Page 10

14. Starting at Rear Corner, position a Solid
Wall Panel on top of plywood floor. The Wall
Panel bottom framing will sit flush with floor
framing.
Important: Make sure all walls are aligned
in their upright position. If not, water may
leak into your shed. Unsure if panel is
facing up or down? check siding on
window wall panel to match alignment.
15. The side wall panels will sit flush at the
corner of the floor, with the front and rear
wall panels sandwiched between them.
Note: Siding will overhang the floor by
approximately 1/2”.
Outside 2x3 framing of wall panel
is flush with outside of floor frame
when properly aligned.
Side Wall Panel
Front
Rear of Shed
13. Lay out all the wall panels and become familiar with their
location. On a Standard Kit, there is 1 Window Wall Panel, 6 Solid
Wall Panels and 1 Narrow Wall Panel. Make sure to position pan-
els right side side up so water is directed away from and not into
shed. Compare siding with Window Wall Panel to determine proper
wall orientation.
Parts (Steps 13 - 21)
Solid Wall Panels
(45 1/2” x 75”) x 5
Window Wall Panel
(45 1/2” x 75”) x 1
Hardware (Steps 13 - 21)
S1 - 2 1/2” Screws
x 18 total
Toll Free 1-888-658-1658 www.outdoorlivingtoday.com [e-mail]
Page 11

18. Continue positioning and securing wall panels around your
floor. Attach wall studs together as per Step 16. Be sure that rear
wall panels fit between the side wall panels (sandwiched).
Do Not Attach
Walls To Floor
Until Step 25.
16. Position a 2nd Solid Wall into place on plywood floor. Butt both vertical wall studs of side and
rear walls together and attach with 3 - 2 1/2” screws. Screw at the bottom, middle and top of stud to
secure properly.
Rear Solid Wall
Side Solid Wall
17. With the corner wall
attachment complete,
position a third wall
panel in place. Wall
siding should overhang
floor by approximately
1/2”. When positioned
correctly, attach both
rear wall panel studs
together as per Step 16.
Rear Solid Wall
2x3 wall framing flush
with floor framing.
Optional: Caulking seams will
help prevent moisture from
entering at seam. Caulking not
included in kit. This will help the
longevity of your shed.
Side Wall Panels
Rear Wall Panels
19. Complete all side
and rear wall attachments.
Front of Shed
Wall panel will
sit flush with
floor framing at
Front of shed.
Toll Free 1-888-658-1658 www.outdoorlivingtoday.com [e-mail]
Page 12

Jamb sits flush with
outside of siding.
21. Make sure top Wall framing is aligned
together as illustrated and attach as per Step 17.
20. Place Window Wall Panel in front.
Parts (Steps 22)
Narrow Wall Panel
(12” x 73”) x 1
Hardware (Steps 22)
S1 - 2 1/2” Screws
x 3 total
22. Position and attach Narrow Wall Panel to left side
wall stud with 3 - 2 1/2” screws as per Step 16. Note:
Narrow Wall is 73” high (2” shorter than Solid Wall
Panels). Siding overhangs adjacent wall stud and floor.
Parts (Steps 23)
Door Jamb
(1 1/2” x 3 3/8” x 73”) x 1
Hardware (Steps 23)
S1 - 2 1/2” Screws
x 4 total
23. Locate Vertical Door Jamb and position flush
against right wall panel stud. The Jamb is 3 1/2” wide
and will sit flush to tip of bevel siding. When positioned
correctly, secure Jamb using 4 - 2 1/2” screws.
Toll Free 1-888-658-1658 www.outdoorlivingtoday.com [e-mail]
Page 13

Parts (Steps 24)
Door Header
(2” x 3 3/8” x 45 1/2”)
x 1
Hardware (Steps 24)
S1 - 2 1/2” Screws
x 4 total
24. Position and attach Door Header to Door Jamb
and Narrow Wall Panel top framing. Header should sit
flush with Door Jamb and Outside of Narrow Wall Panel
Siding Attach with 4 - 2 1/2” screws..
Header has notch in edge that is
positioned to the top and facing outside.
25. When all walls are attached together, check alignment with the floor.
Bottom wall framing should sit flush with outside of floor joists. Confirm 32”
wide door opening at bottom. When positioned correctly, fasten bottom wall
plates to floor using 4 - 2 1/2” screws per wall panel.
Bottom Wall
Framing
Confirm Doorway Opening is 32” at top and bottom.
Angle
screws into perimeter
Floor Joists.
125 1/4”
125 1/4”
Advice: Prior to fastening walls and installing
rafters, take time to confirm your walls are level,
square and plumb.
Measure diagonal at top and bottom of walls
corner-to-corner. This should be approximately
125 1/4”. More importantly, if measurements
are not within 1/4”, your walls are not square.
Adjusting now will make it easier to assemble
the roof section later.
Caulking
Optional: Caulking seams
between bottom wall plates and
floor will help prevent moisture
from entering you shed. Caulking
not included in kit. This will help
the longevity of your shed.
32”
Hardware (Steps 25)
S1 - 2 1/2” Screws
x 32 total
Toll Free 1-888-658-1658 www.outdoorlivingtoday.com [e-mail]
Page 14

26. Position Front Top Plates on top of wall studs so they are
flush on the inside with 2x3 wall framing. There are 3 pieces of
Front Top Plates (2 angle cut on one end and one straight cut on
both ends). Together, the plates should be centered evenly on the
wall left to right. Attach by screwing down into top wall framing
with 3 - 2” screws per piece.Complete both front and rear of shed.
Angle cut
on ends.
Top Plates should be flush
with inside of wall framing.
Parts (Steps 26,28)
Front & Rear Top Plates
(3/4” x 2 1/2” x 32”) x 6
(2 angled end, 1 straight)
Hardware (Steps 26,28)
S3 - 2” Screws
x 18 total
27. Next, attach 2 Side Top Plates (1 per side). The side top
plates are angle cut down the edge. Once again, position top plate
on wall plate so it is flush with inside of wall framing. Side plate
should also be flush with Front Top Plate. Secure with 4 - 2”
screws per piece.
Parts (Steps 27)
Side Top Plates
(3/4” x 2 1/2” x 86”) x 2
(angle cut on edge)
Hardware (Steps 27)
S3 - 2” Screws
x 8 total
Side Top Plate Front Top Plate
28. Position the Rear Top Plates on back wall to complete as per Step 26. Use 3 - 2” screws
per piece.
Toll Free 1-888-658-1658 www.outdoorlivingtoday.com [e-mail]
Page 15

Notched at top
Flashing
29. Locate Gable 1/2 Walls for both sides of shed.
Align framing and gable lapp siding together. Screw
center gable wall framing of each piece together
with 3 - 2 1/2” screws. Note: prior to attaching, try
each combination of Gables for best fit.
Parts (Steps 29-32)
Gable Half Walls
Triangular shaped x 4
Hardware (Steps 29-32)
S1 - 2 1/2” Screws
x 6 total
S3 - 2” Screws
x 4 total
Male & Female
Notch Ends
Flashing
30. Lift up a completed gable section and place on top of Rear Top Plate on wall. The rear gable
framing should sit flush with the inside of the top plate.
Toll Free 1-888-658-1658 www.outdoorlivingtoday.com [e-mail]
Page 16

31. The gable should be centered sideways (left to right) on the top plate. Hint: use a straight edge
to check the angle of the gable framing and top plate. Both angles should line up. Adjust gable
accordingly. Temporarily attach Gable to walls to top plate with 2 - 2” screws. Screw from the
bottom of gable framing down into Top Plate and Wall. Gables may need slight adjustment in Step 44
and then will be completely attached with an additional 6 - 2” screws.
32. Complete positioning and attachment of front gable as per Step 29-31.
straight edge
Flashing overhangs
wall siding.
Toll Free 1-888-658-1658 www.outdoorlivingtoday.com [e-mail]
Page 17

C. Rafter and Roof Section
Exploded view of all parts necessary to complete the Roof Section.
Identify all parts prior to starting.
33. Locate Ridge Boards and attach together with
Metal Ridge Board Connector using 8 - 3/4” screws.
Total Length when connected is 91”. Complete two
Sets. Position Metal Ridge Board Connector evenly on
Ridge Boards.
33 1/2” Long
8 - 3/4” screws
Parts (Step 33)
Ridge Boards Long
(3/4” x 4 1/2” x 57 1/2”)x 2
Ridge Boards Short
(3/4” x 4 1/2” x 33 1/2”)x 2
Hardware (Step 33)
SS2 - 3/4” Screws
x 16 total
Metal Ridge Board
Connector
x 2 total
57 1/2” Long
Metal Roof
Panels (6)
Roof Rafters
(12)
Ridge Boards (4)
2 @ 57 1/2”, 2 @ 33 1/2”
Soffits (4)
Roof Gussets (2)
Metal Ridge
Board
Connectors (2)
Metal Ridge Caps (2)
Foam Enclosures
(Several)
Roof Battens
48 1/4” (16)
Roof Battens
Short 25 1/2” (4)
Batten Spacers (12)
Toll Free 1-888-658-1658 www.outdoorlivingtoday.com [e-mail]
Page 18

35. Attach end of a 45 1/2” long Soffit Board flush to ends of outside
Rafter with 2 - 1 1/4” screws per Rafter end. Drill pilot hole in Soffit
ends to prevent splitting. Attach Ridge Board to opposite rafter end
with 2 - 2” screws, while aligning to bottom of rafter . Center Soffit on
Doubled-up Rafters and secure with 2 - 2” screws. Measure 45 1/2” from
outside rafter and secure Ridge Board to rafter with 2 - 2” screws. Attach
Doubled-up Rafters together with 3 - 2 1/2” screws.
Ridge Board
34. Locate 6 Rafters, 2 Soffits and
completed Ridge Board from Step 33.
Lay out as illustrated on a flat level sur-
face.
Ridge Board
4 1/2” wide
Soffits
56 1/2” Rafters
20 1/2”
23 1/2”
20 1/2”
91”
Centered on
Rafter
45 1/2”
Attach Doubled-up Rafters
with 2 1/2” screws
Soffit
45 1/2”
36. Measure, position and attach mid rafters as illustrated above as per Step 35.
mid rafter
Important: Pilot Hole Ridge
Board & Soffits to prevent
splitting!
Parts (Step 34 - 42)
Rafters
(1 1/2” x 3 1/2” x 56 1/2”)x 12
Soffits
(1/2” x 4 1/2” x 45 1/2”)x 4
Hardware (Step 34 - 42)
S1 - 2 1/2” Screws
x 6 total
S2 - 1 1/4” Screws
x 48 total
S3 - 2” Screws
x 24 total
Important: Ridge
Board must be aligned
as illustrated.
Toll Free 1-888-658-1658 www.outdoorlivingtoday.com [e-mail]
Page 19

37. Flip Rafter Section over so Soffit is facing down.
Starting with the left side, lift completed rafter section
up and place on gable framing.
Soffit
39. When Rafter Section is correctly
positioned, outside rafters will sit equally on gable
framing and Soffit will sit approximately 1/8” away from
wall panels.
Rafter should rest
on gable framing
38. Slide Rafter Section up on gable
framing until bottom of Ridge Board slips
into gable notch.
Soffit should sit
approx. 1/8” away
from wall panel.
Gable Notch
Ridge Board
Rafter
Completed left
side Rafters
40. Place 2nd completed Rafter Section on gable wall framing. Position as per Steps 38 & 39.
Toll Free 1-888-658-1658 www.outdoorlivingtoday.com [e-mail]
Page 20