Olympus VoiSquare User manual

Thank you for purchasing an Olympus VoiSquare.
Please read these instructions for information about using the product correctly and safely.
Keep the instructions handy for future reference.
165
1
29
55
81
109
137
193
221
249
VoiSquare
USER MANUAL
DS-F1
ENGLISH
ČEŠTINA
DANSK
DEUTSCH
ESPAÑOL
FRANÇAIS
NEDERLANDS
POLSKI
РУССКИЙ
SVENSKA
DRAFT

EN
Introduction
2
• The information in this document is subject to change in future without prior notice. Contact Olympus
Customer Support Center for the latest product names, model numbers and other information.
• The display and illustrations of the device used in this manual may be different from the actual product.
While every precaution has been taken to ensure the accuracy of the information in this manual, errors
may occasionally arise. Any questions or concerns regarding doubtful information, or possible errors or
omissions should be directed to the Olympus Customer Support Center.
• Olympus Corporation and Olympus Imaging Corp. are the copyright holders of this manual. Copyright law
prohibits unauthorized reproduction of this manual, or unauthorized distribution of reproductions thereof.
• Note that Olympus will assume no liability in the event of damages, lost earnings, or any claims from third
parties resulting from improper use of the product.
Table of contents
Introduction
Introduction .......................................................................................... 2
Getting started
Identification of parts ............................................................................ 3
Touch screen ......................................................................................................4
Touch screen operations ......................................................................... 5
Installing the battery............................................................................. 6
Charging the battery.............................................................................. 7
Charging using docking station and AC adapter................................................7
Charging using docking station and USB cable .................................................7
Using the lithium-ion battery............................................................................8
Turn the power ON ................................................................................. 9
Memory card........................................................................................ 11
Inserting a micro SD card.................................................................................11
Ejecting a micro SD card...................................................................................11
Various Settings................................................................................... 12
Settings list...................................................................................................... 12
Other information
Device care .......................................................................................... 13
Troubleshooting .................................................................................. 14
Wi-Fi Function...................................................................................... 16
Copyright and trademark information.................................................. 17
Safety precautions ............................................................................... 18
Specifications ...................................................................................... 25

Identification of parts
3
EN
17
8
9
0
!$
%-
=
q
w
e
r
t
)
(
*
&
^
@
#
2
3
4
5
6
1 EAR (earphone) jack
2Notification lamp (LED)
3Speaker for calls *1
4Proximity sensor/luminance sensor
5Touch screen
6Navigation buttons
7Strap hole
8
MIC (microphone) jack
9Built-in microphone *1
0Function button*1
!Slide switch (4-type switch) *1
@Power switch (f)
#Microphone for calls *1
$Battery cover
%Docking station connector
^Location hole for CL3
&Internal Wi-Fi antenna
Do not cover this with a finger or other object.
*Built-in speaker
(Volume buttons
)Battery cover release lever
-USB connector
=Connector for DS-F1
qAC adaptor jack
wUSB connector (mini-AB)
eFoot Switch connector
rEthernet cable connector
tSecurity Slot
*1 Use depends on the applications you install.
Identification of parts
Getting started

EN
Identification of parts
4
Identification of parts
Touch screen
4 Homescreen
1Status bar
Indicates the remaining battery power, device
settings, notifications, and other information
with icons.
2Time display
3Shortcut (application)
4abutton
Displays a list of applications.
TIP
• The operating instructions in this manual
explain operations performed from the
default Home screen. If, for example, another
application is set as the Home screen, the
explanations and operating procedures in
this manual may differ.
• The screen configuration differs depending
on the operating system version.
1
2
3
4

Touch screen operations
5
EN
The device employs a multi-touch interface. The
interface is operated by directly touching it. The
basic operations are described below.
4 Tap
Gently touch a shortcut, list, or other item with a
fingertip and then immediately release your finger.
Use this operation to, for example, select an icon
or item.
Tapping the screen twice with a fingertip is called
a double-tap. Use this operation to, for example,
enlarge an image. Double-tapping the image again
while it is enlarged restores it to its original display
size.
4 Long press
Continue pressing a shortcut, list, or other item
with a fingertip. Use this operation to, for example,
move a shortcut or access a sub menu for the
selected item.
4 Drag
Continue pressing a shortcut, list, or other item
with a fingertip and move your finger to the
desired position without releasing it from the
screen. Use this operation to, for example, adjust
the volume or screen brightness.
4 Flick (Swipe)
Gently swipe the screen with a fingertip. Use this
operation to switch or scroll the screen.
4 Pinch
Place two fingers on the screen and then narrow
the distance between them. Use this operation
to reduce the screen or other item to a size that is
easy to see.
4 Spread
Place two fingers on the screen and then widen
the distance between them. Use this operation to
enlarge the screen or other item to a size that is
easy to see.
NOTE
• Do not push the touch screen forcibly with a
finger or press it with a sharp-pointed object
(fingernail, ballpoint pen, pin, etc.).
• Set the device to power save mode before
carrying it around in a pocket, bag, etc.
• The touch screen may not operate normally
in the following cases. Furthermore, be
careful because the following cases will result
in incorrect operation.
• When touched while wearing gloves.
• When touched with the tip of a fingernail.
• When touched while a foreign object is
on the operating surface.
• When touched while a protective sheet,
sticker, etc. is affixed.
• When touched while the touch screen
is wet.
• When touched with sweaty or wet
fingers.
Touch screen operations

EN
Installing the battery
6
This device uses a lithium-ion battery specified by
Olympus (LI-92B). Do not use any other type of
battery.
1To open the battery cover, slide the
battery cover lock release lever in the
direction of the arrow.
2With the label facing up, align the
terminals on the device and the
battery, then press down in at A, and
set the battery into place by pressing
it inward at B.
As shown, set the battery so that it tucks under the
protruding section of the device.
3Slide the battery cover until it is
completely closed.
NOTE
• Be sure to firmly close the battery cover (slide
until the battery cover lock clicks).
• Do not close the battery cover if the battery is
not completely inserted.
• Check for any metallic foreign matter or dust
on the terminal of the battery.
• Do not use a battery other than that
specified.
• Turn OFF the device before removing the
battery. Removing the battery while the
device is still in use may cause malfunctions,
file corruption or file loss.
• Remove the battery if you are not going to
use the device for an extended period of
time.
• After removing the battery, it may become
necessary to re-set the time and date if you
leave the battery out of the device for more
than 15 minutes or if you remove the battery
right after loading it into the device.
Installing the battery

Charging the battery
7
EN
After loading the battery into the device, you
can charge it by connecting the USB cable to
the device, or by using the docking-station in
combination with the USB cable or the AC adapter.
Fully charge the battery (approx. 2 hours 30
minutes) before use.
NOTE
• Lithium-ion batteries are self-discharging. Be
sure to charge the battery before you start
using.
Charging using docking station and AC
adapter
2
1
3
4
Charging using docking station and USB
cable
1
2
Charging directly via USB cable
NOTE
• Charge the battery frequently during the first
period of use. The battery will perform better
after several charge/discharge cycles.
• Models of batteries which are different from
the included one may not be charged.
• Charging the battery via the USB cable
connection may not be successful depending
on the power capacity of the USB port in your
PC. Use the AC adapter instead.
• Do not set or remove the device from the
docking station while operating.
Charging the battery

EN
Charging the battery
8
Charging the battery
• Do not charge the device through a USB hub.
• Do not attach or remove the battery if the
USB cable is connected.
Using the lithium-ion battery
The included battery is exclusively for use with
the Olympus VoiSquare DS-F1. Do not use in
combination with other electronic equipment.
Cautions concerning the battery
Read the following instructions carefully when you
use the battery.
4 Discharging:
Rechargeable batteries self-discharge while not in
use. Charge it regularly before use.
4 Battery life:
Over time, the rechargeable battery may gradually
wear down. When the operating time becomes
shorter even if the rechargeable battery is fully
charged under the specified condition, replace it
with a new one.
4 Operating temperature:
Rechargeable batteries are chemical products.
Battery efficiency may vary even when operating
within the recommended temperature range.
This is an inherent nature of these products.
4 Recommended temperature range
of use:
During operation:
0°C - 42°C/ 32°F - 107.6°F
Charging:
5°C - 35°C/ 41°F - 95°F
Storage for a long period:
–20°C - 60°C/ –4°F - 140°F
Using the battery outside the above
temperature range may result in declining
efficiency and shorter battery life.
NOTE
• When disposing the batteries, always observe
the local laws and regulations. Contact your
local recycling center for proper disposal
methods.
• If battery is not fully discharged, protect it
against short-circuiting (e.g. by taping the
contacts) before disposal.
For customers in Germany:
Olympus has a contract with the GRS (Joint Battery
Disposal Association) in Germany to ensure
environmentally friendly disposal.
Battery indicator
The battery indicator on the display will decrease as
the battery loses power.
• When this [ ] indicator appears on the display,
charge the battery as soon as possible. When
the battery is too weak, [ ] and [Power off] will
appear on the display and the device will shut
down.

Turn the power ON
9
EN
1While the device is turned OFF, slide
the power switch (f) in the direction
of the arrow for at least 2 seconds.
• The device vibrates and then the lock screen
appears after a short while.
2Move (drag) the lock icon (h) on the
Home screen to the unlock icon (i)
without removing your finger from
the screen.
Turning the power OFF
Existing data, mode settings and the clock setting
are saved when the power is turned OFF.
1Slide the power switch (f) in the
direction of the arrow for at least one
second.
2Tap [ Power off ].
3Tap [ OK ].
TIP
• Turning the power OFF whenever the device
is not in use minimizes battery consumption.
Turn the power ON

EN
Turn the power ON
10
Turn the power ON
Power save mode
When you set power save mode, the screen turns
off and the screen lock is set. This mode prevents
unintended operation of the touch screen when
carrying the device.
1Slide the power switch (f) in the
direction of the arrow.
TIP
• When the device has been stopped for at
least 15 seconds (default setting) after power
ON, the device automatically enters the
power save mode.
• To release the power save mode, slide the
power switch again.
Force termination
The device may not accept an operation while a
large volume of data is being transferred. Please
wait until the process is finished.
If the screen is still frozen after waiting a short
while, the power can be forcefully turned OFF as
follows.
NOTE
• Please note that the power is being forcefully
turned OFF so any data being processed or
settings being configured may not be saved.
1Slide the power switch (f) in the
direction of the arrow for at least 5
seconds.