Omega Crime guard 850i5 User manual

Crime Guard

850i5

OPERATION MANUAL

FRONT COVER

PRINTER’S NOTE:

production front cover

is color; this is a

place marker cover.

ProductsmanufacturedandsoldbyOMEGARESEARCH&DEVELOPMENT,

INC. (the "Company"), are warranted to be free from defects in materials and

workmanship under normal use. If a product sold by the Company proves to be

defective,theCompany willrepairor replaceitfree ofchargewithin thefirstyear

and thereafter all parts to be repaired will be free with only a nominal charge for

Omega'slaborandreturnshipping,totheoriginalownerduringthelifetimeofthe

car in which it was originally installed.

All products for warranty repair must be sent postage prepaid to Omega

Research & Development, Inc., P.O. Box 508, Douglasville, Georgia 30133, or

send via UPS to: 981 N. Burnt Hickory Rd., Douglasville, Georgia 30134, with

billofsale or other dated proof of purchase.Thiswarranty is nontransferable and

doesnotapply to any product damagedbyaccident,physical or electrical misuse

or abuse, improper installation, alteration, any use contrary to its intended

function, unauthorized service, fire, flood, lightning, or other acts of God.

This warranty limits the Company's liability to the repair or replacement of

theproduct.TheCompanyshallnotberesponsibleforremovaland/orreinstallation

charges, damage to or theft of the vehicle or its contents, or any incidental or

consequential damages caused by any failure or alleged failure of the product to

function properly. UNDER NO CIRCUMSTANCES SHOULD THIS

WARRANTY,ORTHEPRODUCTCOVEREDBYIT,BECONSTRUED

AS A GUARANTEE OR INSURANCE POLICY AGAINST LOSS. The

Companyneitherassumesnorauthorizesanypersonororganization tomake any

warranties or assume any liability in connection with the sale, installation, or use

of this product.

This device complies with F.C.C Rules part 15. Operation is subject to the

following two conditions: (1) This device may not cause harmful interference

and,(2) Thisdevicemustacceptany interferencethat maybereceived, including

interference that may cause undesired operation.

The manufacturer is not responsible for any radio TV interference caused by

unauthorizedmodificationstothisequipment. Suchmodifications couldvoidthe

user’s authority to operate the equipment.

L I M I T E D L I F E T I M E W A R R A N T Y

Omega Research and Development, Inc.

P. O. Box 508

Douglasville, Georgia 30133

www.caralarm.com 03/07 MO-CG 850i5 REV1

BACK COVER

PRINTER’S NOTE:

production back cover

is color; this is a

place marker cover.

This device complies with FCC Rules part 15. Operation is subject to the

following two conditions, (1) This device may not cause harmful inter-

ference and, (2) This device must accept any interference that may be

received, including interference that may cause undesired operation.

The manufacturer is not responsible for any radio or TV interference

caused by unauthorized modifications to this equipment. Such modifica-

tions could void the user's authority to operate the equipment.

One or more of these patents may apply to this product:

#5,612,669 #5,654,688 #5,663,704 #5,729,191 #5,818,329 #5,612,578 #5,739,747

#382,558 #385,878 #5,750,942 #5,739,748 #5,719,551 #406,107 #701,285

#5,973,592 #5,982,277 #5,986,571 #6,011,460 #6,037,859 #6,049,268 #6,130,605

#6,130,606 #6,140,938 #6,140,939 #6,150,926 #6,144,315 #6,184,780 #6,188,326

#6,243,004 #6,249,216 #6,275,147 #6,297,731 #6,320,514 #6,320,498

ForeignPatent #199700312 #EP0817734B1 #98906445.6 #2,320,248 #701,285

Omega Research and Development, Inc.

www.caralarm.com

Page - 2

Coin batteries used in the transmitter which is used to operate this

security system may contain Perchlorate Material - special handling

may apply. See www.dtsc.ca.gov/hazardouswaste/perchlorate

Page - 43

Complete Programmable Features Matrix

USER Features Ignition on, off, then press Valet Switch 5times (RED Status Light).

# Feature Default Setting Option 2nd Option 3rd Option

1 SecureCode 1 & 0 2 stages, of up to 9 presses each (total of 99 possible combinations)

2 Last Door Arming OFF (L) ON w/o doorlock (U) ON w/ doorlock (2)

3 Automatic Rearming OFF (L) ON w/o doorlock (U) ON w/ doorlock (2)

4 Starter Interrupt Functions Alarm only (L) Off(U) Automatic (2) Alarm+AntiGrind (3)

5 Ignition Activated Override OFF (U) ON (L)

6 Doors Lock With Ignition On ON (L) OFF (U)

7 Doors Unlock With Ignition Off ON (3) OFF (L) o/p 1 only (U) o/p 2 only (2)

8 Open Door Bypass to above ON (L) OFF(U)

9 Confirmation Chirps ON (L) OFF (U) exc. Valet (2) Valet only (3)

10 Confirmation Chirp Volume Medium Loud (2) Low (L) Med Lo (U) Loud (3)

11 Activated Alarm Cycle 30 Seconds (L) 60 Sec. (U) 90 Sec. (2) 120 Sec. (3)

12 Lights On Upon Disarm ON (L) OFF (U)

13 Disarm Upon Trunk Release ON (L) OFF (U)

14 Arming Delay 3 Seconds (L) 15 Seconds (U) 30 Seconds (2) 45 Seconds (3)

15 Steady Siren / Pulsed Horn Steady Siren (L) Pulsed Horn Lo (U) Pulsed Med. (2) Pulsed Hi (3)

16 Alarm Functions Bypass OFF (U) ON (L)

17 Ignition Anti-Carjacking OFF (U) ON (L)

18 Door Anti-Carjacking OFF (U) ON (L)

19 Remote Anti-Carjacking OFF (U) ON (L)

20 Open Door Warning at Arm OFF (U) ON (L)

21 IIIButton Operation Panic (L) 3rd Chan. (U) 4th Chan. (2) 5th Chan. (3)

22 Remote Start Run Time 10 Min. (U) 5 min. (L) 15 min. (2) 20 min. (3)

23 Steady/Flash Lights Rem. Start Steady (L) Flashing (U)

INSTALLER Features Ignitionon,off,thenpressValetSwitch10times(GREENStatusLight).

1 Doorlock Functions .8 second (L) 3 Seconds (U) Double Unlock (2) Total Closure (3)

2 Light Relay Functions Dome Light (L) Lock (U) Ignition (2) Accessory (3)

3 Horn Relay Functions Horn, med. (L) Unlock (U) Ignition (2) Accessory (3)

4 Turbo Timer OFF (U) ON (L)

5 Manual Trans. Remote Start OFF (U) ON (L)

6 “Tach Wire” or “Tachless “ Tachless (L) Tach (U)

7 Ext. Starter Cranking Time .7 (minimum) ( L) 1.25 (U) 1.75 (2) 2.5 (maximum) (3)

8 Remote Start Relay Ignition (L) Accessory (U) Starter (2)

9 Arm/Disarm or Add. Chan. Arm/Disarm (L) Arm/Ch. 5 (U) Ch. 4 / Disarm (2) Ch. 4 / Ch. 5 (3)

10 Gasoline or Diesel Engine Gasoline (L) Diesel (U)

Page - 3

This Booklet Contains

Introduction to the System ..................................................... 4-6

Status Light, Valet Switch, Controller & Transmitter

System Versatility - An Important Note ........................................ 6

Using the Crime Guard System .............................................. 7

Arming Using the Controller or Transmitter .......................... 7-8

Arming Bypass, Sensor Bypass

Automatic “Last Door Arming” of the System ...................... 8-9

While the System is Armed, and should it Trigger ................ 9-10

Prewarning

Disarming the System Using the Controller or Transmitter .. 10-11

Safety Disarm Feature; Activation Alert; Automatic Rearming

Disarming By Emergency Override ....................................... 11-12

Remote Panic Feature ............................................................. 12

Remote Engine Starting .......................................................... 13-16

Safety Features, Stick Shift Remote Starting; Pit-Stop; Turbo Timer

Other Controller and Transmitter Operations......................... 16-17

2nd Channel, 3rd Channel, Silent Arming & Disarming, Sensor Bypass

Using the Valet Switch ........................................................... 17-19

Alarm Valet Mode & Starting Valet Mode

SecureCode.............................................................................. 19-20

The Status Light ...................................................................... 20-21

2-Way Controller .................................................................... 22-24

Icons & Programming

Anti-Carjacking Protection ..................................................... 25

Controller and Transmitter Protection .................................... 26

How to Program Controller or Transmitters........................... 26-27

How to Program Features ....................................................... 28-29

User Programmable Features .................................................. 30-37

Installer Programmable Features ............................................ 38-42

Complete Programmable Features Matrix.............................. 43

Limited Lifetime Warranty ..............................................Back Cover

Feature #10 Gasoline Or Diesel Engine

Factory Default Setting Gasoline (press “arm/lock” button to program)

Option: Diesel (press “disarm/unlock” button to program)

Thisfeaturechanges the system's timingofthe ignition andstarteroutput sequence

for remotely starting vehicles with a diesel engine. This feature should only be

programmed by the installer.

Feature #8 Programmable Remote Start Relay

Factory Default Setting Ignition Output

(press “arm/lock” button to program)

Options:

Accessory Output (press “disarm/unlock” button to program)

Starter Output (press “II” button to program)

TheCrimeGuard850i5features4dedicatedremotestartoutputrelays,oneofwhich

is programmable (this is the unit’s large blue output wire). Operation choices are

ignition, accessory or starter power output. This feature should only be

programmed by the installer.

Feature #9 Arm, Disarm or Additional Channels

Factory Default Setting Arm / Disarm

(press “arm/lock” button to program)

Options:

Arm / Channel 5 (press “disarm/unlock” button to program)

Channel 4 / Disarm (press “II” button to program)

Channel 4 / Channel 5 (press “III” button to program)

The 850i5has outputs designed for arming and/or disarming a factory-equipped

securitysystem. Thesewiresmaybeusedinsteadtoprovidefurthersystemoutputs,

which are remotely operated by the controller or transmitter. These outputs are in

addition to the 2nd channel and 3rd channel outputs, the operation of all of these

outputs is explained on page 17.

As shown in the programming assignment, the arm, disarm, channel 4 and

channel 5 are programmable as various combinations. For example, if the disarm

output is needed, but not the arm output, then channel 4 may be made available for

use.

Page - 42

Time can be used for difficult-to-start engines. This feature should only be

programmed by the installer.

Note: “Base timing” is the maximum time period that the 850i5will engage the

starter, but only if it does not detect the engine has started running.

Valet

Switch

Status

Light

Congratulations for your choice of the most versatile, fully-featured vehicle

securityandconveniencesystemavailabletoday,theCrimeGuard850i5byOmega

Research and Development. To enjoy the most from your new system, please take

a few moments to learn about the principal user components, and the basic

operation of the system. These subjects are found in next several pages, followed

by more detailed specifics of complete operations and features.

Page - 4

Introduction to the System

• The Valet Switch can also be used, in conjunction with

thevehicle’signition key, toperforman emergency disarmingofthe security

systemintheeventthetransmitterortransceiverislostorbecomesinoperable.

This is referred to as “performing an Emergency Override”.

• The Valet Switch is used in the procedure of programming operational

features and also for encoding transmitters and transceivers to the system.

A complete description of the Valet Switch and its operations is on pages 17-19.

The multicolored Status Lights report the operational

statusofthe system at alltimes,and also servesasa visual

deterrenttobreak-insandtheft. Specificdescriptionofthe

Status Light operation may be found on pages 20-21.

The Valet Switch has three main functions:

• The Valet Switch can be used to turn off the security

functions, including any automatic arming or locking

features (if used), and/or remote engine starting

functions of the system. The former is “Alarm Valet

Mode”; the later is “Starting Valet Mode” .

The system can operated by two types of devices: the 2-Way Controller and the

1-Way Transmitter. Your system comes with one of each of these, pre-learned

to operate the system. The controller, in addition to operating your system, also

receives signals from the system, and displays a variety of system conditions on its

LCDscreen. ThisisthepatentedEcho2-waytechnology. Thetransmitterwillfully

operatethesystem, but itcannot receive signalsnorreport events from thevehicle.

Your system can be operated by as many as four controllers and/or transmitters.

Oneof thecomponents,typicallymountedon thewindshield, istheWindowUnit

module which contains the Status Lights and the Valet Switch. The window

unit also receives and transmits the Echo technology

communications for the system’s 2-way operation.

Thecontroller andthe transmitterboth sharethesamefouroperationalbuttons,and

their use to operate the Crime Guard system is the same. These buttons and a brief

description of what they do are:

this is done will the system accept a remote start command, and the vehicle must

remain undisturbed until that point. The complete instructions for remote starting,

including Stick Shift Remote Starting, starts on page 40.

This feature should only be programmed by the installer, and the operation of

this feature depends on the correct connection of the safety wire to the vehicle’s

parking brake. Please refer to the Installation Instructions manual for proper

connection of this wire.

Note: Feature #4, Turbo Timer, and Feature #5, Stick Shift Remote Starting, may

both be used together in the 850i5.

Feature #7 Extended Starter Cranking Time

Factory Default Setting Minimum (.7 Second)

(press “arm/lock” button to program)

Options:

Medium Lo (1.25 Second) (press “disarm/unlock” button to program)

Medium Hi (1.75 Second) (press “II” button to program)

Maximum (2.5 Second) (press “III” button to program)

ExtendedStarterCrankingTimeoperatesinconjunctionwiththepreviousfeature’s

“Tachless” setting. The Crime Guard 850i5processor is capable of detecting the

running engine by two separate methods- the use of the vehicle’s tachometer

(“tach”) wire for a direct engine RPM input, or by monitoring the vehicle’s

fluctuating voltage levels caused by the starting process. This feature sets the

duration of the starter output’s base timing for the voltage sensing type of starter

output operation. There are four different base starter output settings. While the

default-setminimumissufficientfor most vehicles; the Extended Starter Cranking

Page - 41

Feature #6 “Tach Wire” or “Tachless” Starter Operation

Factory Default Setting Tachless (press “arm/lock” button to program)

Option: Tach Wire (press “disarm/unlock” button to program)

This feature selects the 850i5processor’s method of determining the status of the

engine running during remote start operation. As explained in the previous

feature’s description, “Tachless” mode has an associated base starter output time

duration. However,ifthevoltagefluctuationisdetectable,theprocessoradjuststhe

starteroutputtimeaccordingly. Whenthisfeatureissetfor “TachWire” operation,

the base starter output increases to 3 seconds, but the processor adjusts the actual

starterengagementtimeaccordingly. Connectingand useofthe“TachWire” isthe

most reliable form of engine running information input, and its use is recom-

mended. This feature should only be programmed by the installer.

Important: Before this feature is programmed, please refer to the “Installation

Manual” for proper wiring connection and the Tach Learning Procedure, both of

which are required for use of this feature.

Page - 40

Feature #5 Stick Shift Remote Starting

Factory Default Setting Off (press “disarm/unlock” button to program)

Option: On (press “arm/lock” button to program)

This feature changes the parameters of the 850i5’s remote start operation to be

suitable for manual transmission-equipped vehicles via a “setup” procedure which

must be followed upon exiting the vehicle. When this feature is turned on, the

operator must set the parking brake and then press the controller or transmitter’s

“arm/lock”and“disarm/unlock”buttonsatthesametime,whichkeepstheengine

running after removing the ignition key. After exiting, the user must then arm the

system, locking the vehicle doors, by pressing the “arm/lock” button. Only after

Feature #4 Turbo Timer

Factory Default Setting Off

(press “arm/lock” button to program)

Options:

Run 1 Minute (press “disarm/unlock” button to program)

Run 2 Minutes (press “II” button to program)

Run 3 Minutes (press “III” button to program)

This feature, the operation of which is described on page 16, when turned on

configures the 850i5to automatically keep the engine running briefly after it is

turnedoff. Thisoperationisdesignedspecificallyforvehicleshavingturbocharged

engines (the user may temporarily bypass the feature if desired).

This feature should only be programmed by the installer, and the operation of

this feature depends on the correct connection of the safety wire to the vehicle’s

parking brake. Please refer to the Installation Instructions manual for proper

connection of this wire.

Feature #3 Horn Relay Functions

Factory Default Setting Horn Output

(press “arm/lock” button to program)

Options:

Door Unlock (press “disarm/unlock” button to program)

Ignition Output (press “II” button to program)

Accessory Output (press “III” button to program)

This is the second of two built-in relays which can be programmed to perform

several different functions. The primary function of this second relay, is that it is

available to operate the vehicle’s existing horn; either in conjunction with the

electronic siren, or in place of the siren. Using both the siren and the horn creates

an extremely effective security system.

Optionally, if desired or needed, this relay can be programmed to be a door

unlock relay, or as additional medium-capacity ignition or accessory outputs, if

needed for remote starting use.

• Pressing the “arm/lock” and “disarm/unlock” buttons together activates the

remote starting feature of the Crime Guard 850i5.

“disarm/unlock”

• Pressing and releasing the “disarm/unlock” button disarms the system and

unlocks the doors unless the alarm is triggered, in which case it will disarm the

activated alarm, but not unlock the doors unless the button is pressed again.

• Pressing and holding this button for three seconds will first disarm, and then

activate the Panic feature, unlocking the doors.

• The unlock operation may be optionally configured during the system’s

installation so that pressing this button once disarms the system and unlocks

only the driver's door, and pressing a second time unlocks all of the doors.

Page - 5

The 1-Way Transmitter

“III” button

“II” button

“disarm/unlock”

button

“arm/lock”

button

“arm/lock”

• Pressing and releasing the “arm/lock” button arms the security system and

locks the doors.

• Pressing and holding this button for three seconds will first arm, and then

activate the Panic feature, locking the doors.

The 2-Way Controller

“III” button

“II” button

“P”rogram

button

“arm/lock”

button

“disarm/unlock”

button

“II” or “:”

• Pressing the “II” button for two seconds can be used to activate an extra output,

known as the “2nd channel”, for an optional function such as trunk release.

• Pressingand releasing thisbuttontwice armsordisarms thesystemwithout the

confirmation chirps.

• Pressing this button immediately after arming will leave the alarm armed, but

with the shock sensor feature bypassed.

• Pressing the “II” and “III” buttons together operates the 3rd channel output.

“P” on the controller only.

• The controller has a fifth button, “P”, which will illuminate the LCD screen

when pressed. This is also the “Programming” button; it is used to customize

controller operations, which is explained on pages 22-24.

“III” or “ ”

• Pressing and holding the “III” button for 3 seconds will activate the Panic

feature, but without locking or unlocking the doors.

• The “III” button can be reprogrammed so that it can operate an additional 3rd

channel output, instead of operating Panic.

...

Page - 6

The “Echo” operation of the 850i5the 2-Way Controller receiving

and reacting to signals from the system in the vehicle, is included

inthefollowing generalsystemoperationdescriptions;the Echo’s

icons and its programming are detailed on pages 22-24.

- IMPORTANT -

TheCrimeGuard850i5isthemostversatilevehiclesecuritysystem

made. It has many programmable features and includes built-in

programmable relays, which can offer more features and opera-

tions which are described in the basic system instructions.

To a large degree, these extra features and operations are config-

ured at the installation of the system. Please read the sections of

this manual which explain programmable features, and please

consult your installer for specifics on how your system is config-

ured, and for installation options which may have used, or can be

added to system after installation.

EXAMPLE- the 850i5can sound the vehicle’s horn in place of or in

addition to the electronic siren which is included with it. But the

operations are described with the siren only.

Page - 39

• The first setting (programmed by the “arm/lock” button) has the system

produce both the lock and unlock outputs as .8 second in duration. This is the

most common form of output needed, which interfaces most vehicles.

• The second setting (programmed by the “disarm/unlock” button) changes the

lockand unlockoutputstobea longer3 secondpulseoutput. This isfor certain

vehicles which require a longer output pulse from the system’s control unit;

typicallycars havingvacuum pumpsystems,althoughthelonger settingis also

more suitable in some newer vehicles.

• Somenewervehiclesrequireadoublepulseoutputtoremotelyunlockthedoors

and/ortodisarmafactory-equippedsecurity system, which is what the Double

Pulse Unlock setting provides (it is programmed by the “II” button ). The lock

output pulse, in this setting, is .8 second.

• The Total Closure Lock Output (programmed by the “III” button) may be used

with vehicles which are originally equipped with the total-closure feature.

Typically, a total closure feature is when locking the vehicle’s doors if the key

in the door is held to “lock” for a period of time the vehicle will close all

windows and the sunroof, in addition to locking the doors.

Selecting this feature setting changes the system’s door lock output pulse from

a .8 second to as long as a 28 second duration output. The unlock output is 3

seconds in this setting.

Note: When this feature is turned on, during the 28 second period after arm-

ing the system, the lock output can be stopped on demand by pressing the

“arm/lock” or “disarm/unlock” button. Only the output will stop- pressing

either button again will normally operate the system, and at any time after the

28 second lock output period ends.

If either of the programmable relays are set for lock or unlock operation (the next

two Installer Programmable Features), the settings if this feature will operate the

programmable relays accordingly, in addition to the primary system doorlocking

outputs.

Feature #2 Light Relay Functions

Factory Default Setting Dome Light Output

(press “arm/lock” button to program)

Options:

Door Lock (press “disarm/unlock” button to program)

Ignition Output (press “II” button to program)

Accessory Output (press “III” button to program)

The Crime Guard 850i5has two built-in relays, which can be programmed to

performseveraldifferentfunctions. Theprimaryfunctionofthisrelay,istooperate

the vehicle’s dome, or interior lighting as part of the system’s operations. Option-

ally, if desired or needed, this relay can be programmed to be a door lock relay, or

asmedium-capacityignitionoraccessoryoutputs,ifneededforremotestartinguse.

Arming Using the Controller or Transmitter

The system can always be armed from the controller or transmitter, if the

ignition key is “off” and the system is not in the Valet Mode. To arm the system,

exitthevehicle,closeallofthedoors,andsimplypressandreleasethe“arm/lock”

button once.

YourCrime Guard system isdesigned to detertheftof both yourvehicleand its

contents. “Arming” your system turns on its protection, disabling the vehicle’s

starterandlockingthedoors. OncethesystemisArmed,anyintrusionattemptwill

Activateit, soundingthe electronic“Psyren”psycho sirenand flashingtheparking

and interior lights to attract attention. The unique and patented “2-in-1” Psyren

psycho siren actually produces the sounds of two different sirens at once, ensuring

that it won’t be ignored like all of the other “common” car alarms. Disarming the

system turns off the protection, unlocking the doors and turning on the parking and

interior lights, allowing lighted access to, and normal use of, the vehicle.

There are two methods of arming the Crime Guard:

1- The first method is to use the controller* or transmitter, by pressing and

releasing the “arm/lock” button. The system must not already be armed or be

in Valet Mode, and the vehicle’s ignition key must be off.

2- The second method is Last Door Arming, which configures the system to

automaticallyarmitselfeverytimeyouexit thevehicle. Thismethodofarming

is programmable, and may be used or not used as desired.

Using the Crime Guard System

Regardlessofhowitbecamearmed,ifthesystemisarmedthewindowunit’sStatus

Light flashes in the red color.

Thesystem’sreaction: Theparkingandinteriorlightswillflashonce,thesiren

will chirp once and the Status Light will begin to flash red, confirming that the

system is armed.* In addition, the doors will lock and the starter interrupt will

engagetopreventanyattempttostartthevehicle. Yoursecuritysystemisnowfully

armed, and is ready to respond if an intrusion attempt is detected.

If the controller was used: Immediately after the system responds the con-

troller will chirp twice (or four times if a zone is bypassed), the “ARM” icon will

appear, the “locked lock” icon appears, confirming that doors have locked, and the

number of operating transmitters or transceivers is briefly displayed.

Page - 7

*If the 2-way controller is used to operate the system, it will receive a signal

back and confirm that the operation was performed.

*The system is described in its most common and basic configuration, with

doorlocks connected, and he interior lights must be connected. The vehicle

horn may used in place of, or in addition to, the system’s electronic siren.

The Installer Programmable Features

Thesecond group of features,the Installer ProgrammableFeatures,are accessed as

the second level of features’ programming, which is pressing the Valet Switch 10

times instead of 5 times when entering Programming Mode (page 28). Caution:

Thesefeatureshaveacriticalaffectuponthesystem’soperations,andinmany

cases, also upon the system’s wiring connections. These features should

NEVER be changed, except by the installer or other qualified professional.

The companion Installation Instructions booklet should be consulted for wiring

connections associated with these features.

The Crime Guard 850i5’s 10 Installer Programmable Features:

1 Doorlocking Functions

2 Light Relay Functions

3 Horn Relay Functions

4 Turbo Timer

5 Manual Transmission Remote Starting

6 “TachWire” or “Tachless”Starter Operations

7 Extended Starter Cranking Time

8 Programmable Remote Start Relay

9 Arm, Disarm or Additional Channels

10 Gasoline or Diesel Engine

Use the step-by-step instructions on pages 28-29 to change any of the Installer

Programmable Features, along with the feature’s option choices and related

programming controller/transmitter button assignment found in the following

individual feature descriptions.

Page - 38

Installer Programmable Features should only be used by the original

or other qualified installer, AND individual Installer Features should

only be used, where applicable, with the correct wiring connections.

Feature #1 Doorlocking Functions

Factory Default Setting .8 Second Lock & Unlock Output

(press “arm/lock” button to program)

Options:

3 Second Lock & Unlock Output (press “disarm/unlock” button to program)

Double Pulse Unlock Output (press “II” button to program)

Total Closure Lock Output (press “III” button to program)

This single feature gives the installer several needed options, to match the 850i5’s

doorlocking outputs to suite different vehicle requirements.

Arming Bypass: Upon arming, if any system sensing circuit is inoperable,

thatcircuitonlywillautomaticallybebypassed. Whenanunsecuredsensingcircuit

isinabypassedstate,allothernormallyoperatingcircuitswillbeprotected. Should

the bypassed circuit become secured, it will automatically be reinstated for

protection 5 seconds later. When certain protection circuits are bypassed, such as

the hood/trunk and impact sensor, and the system is armed, it will indicate this by

chirping the siren three time and flashing the parking lights three times instead of

the normal arming indication of one chirp and one flash.

For example, should the trunk be open, you can still arm the system with the

transmitter,andinthiscasethearmingindicatorwill be3 sirenchirps and3parking

light flashes. Arming Bypass will only operate when arming the system with the

transmitter.

If the controller was used for the arming, it will chirp three times instead of the

normal one time, and its display will also flash the icon of the zone which is

bypassed.

Sensor Bypass: When arming the Crime Guard system with the controller

or transmitter, you may conveniently and easily temporarily deactivate the impact

sensor without affecting the system’s other sensing circuits. To deactivate the

sensor, arm the system by pressing the “arm/lock” button, then press and release

the transmitter’s “II” button within three seconds. You will hear a second siren

chirp confirming that the security system has armed without the sensor protecting

thevehicle.Thenexttimethesystemisarmednormallywithone“arm/lock”button

press, the sensor will again be part of your protection.

If the controller is used for the arming and then bypassing the sensor, let it

confirm the arming, then press the “II” button. The controller will then chirp twice

and turn on its “Impact” icons to indicate the bypassed sensor.

Automatic “Last Door Arming” of the System

The Crime Guard can also be programmed to automatically arm itself, and in

this process, to lock or not lock the doors. When this feature is utilized, closing the

vehicle's last door will cause the siren to chirp once, the parking and interior lights

to flash once and the Status Light to start rapidly flashing red. Thirty seconds later

the siren will chirp again and the lights will flash again, the doors will lock (which

is separately programmable) and the Status Light will slow to a steady red flash,

confirming that the security system is fully armed. If a point of entry is reopened

beforethesinglesirenchirpat30seconds, theLastDoorArmingprocess stops,and

will reset to start over when the point of entry is again closed. All protected entries

The Crime Guard system’s separate “arm/lock” and “disarm/unlock” button

design allows repetitive operation- if already armed, pressing the “arm/lock”

button will simply rearm the system, and vice versa when pressing the “disarm/

unlock” button. Controllers and transmitters both operate in this fashion.

Page - 8

Option: On (press “arm/lock” button to program)

When this feature is turned on, if one of the vehicle's doors is open at the time that

thesystemisarmedviathecontrollerortransmitter, thesiren will chirp3 timesand

the parking lights will flash 3 times instead of once.

Feature #21 “III” Button Operation

Factory Default Setting Panic

(press “arm/lock” button to program)

Options:

3rd Channel (press “disarm/unlock” button to program)

4th Channel (press “II” button to program)

5th Channel (press “III” button to program)

This feature changes how the controller’s or transmitter’s “III” button operates.

Normal operation, or the default setting, has the “III” button operate the Panic

feature. This feature allows changing it to instead operate the 3rd channel or either

of the two other optional channel outputs. Panic can still be operated, by the

alternativemethodsofpressingeitherthe“arm/lock”and“disarm/unlock”button

for 3 seconds.

Page - 37

Feature #22 Remote Start Run Time

Factory Default Setting 10 Minutes

(press “disarm/unlock” button to program)

Options:

5 Minutes (press “arm/lock” button to program)

15 Minutes (press “II” button to program)

20 Minutes (press “III” button to program)

This feature sets the period of time that the engine will run after being remotely

started. If the engine is not stopped by controller/transmitter command or a safety

circuit violation, the engine will automatically stop upon the expiration of the

selected time period. Caution: The remote engine starting feature should

NEVERbeusedwhenthevehicleisparkedinanenclosedstructureorgarage.

Feature #23 Steady/Flashing Lights During Remote Start

Factory Default Setting Steady (press “arm/lock” button to program)

Option: Flashing (press “disarm/unlock” button to program)

ThisFeatureconfigures the system's operationofthe vehicle’s parkinglightswhen

the engine is running after it has been remotely started. The factory default setting

has the parking lights illuminating steady during the engine run time; the other

setting flashes the parking lights on and off during the engine run time.

Page - 9

While the System is Armed, and should it Trigger

Whilethesecuritysystemisarmed,theStatusLightflashesredincolor. Should

any intrusion attempt be detected, the system will instantly activate, or "trigger".

Oncetriggered,theCrimeGuardloudlysoundsthesirenandflashestheparkingand

interior lights on and off.

must be closed to initiate the Last Door Arming sequence.

TotemporarilypreventthesystemfromautomaticallyLastDoorArming,youhave

theseoptions:putthesystemintoAlarmValetMode(page18),leavethedooropen,

or,inmost cases turning on the dome lightmaycause the system to detect thatyour

door is still open. Leaving the ignition key turned "on" is not recommended.

Last Door Arming offers a high level of security, since you do not have to

remember to arm the security system every time you leave the vehicle, and using

itmayentitleyoutoaninsurance discount(pleasecheckwithyouragentorcarrier).

When it is first triggered, the Status Light changes its red flash pattern, and the

doors will automatically relock. Should a door be open when the system triggers,

itwillwaituntilthe door is closed, and at that time relock thedoors. Theautomatic

relockingofthedoorsdeniesaccesstothethief,andisjustoneofthemanyexclusive

patented features of the Crime Guard. The siren will sound and the parking and

interior lights will flash for 30 seconds unless you disarm the system first (60, 90

and 120 seconds activated periods are options- see Feature #11, page 34). If all

protected entries are secure at the end of the 30 seconds, the system will stop and

rearm itself, ready to detect further entry attempts. If there is a protected entry still

openorthe impactsensorstillinaviolatedstateattheendof 30seconds,the system

willreactivatefor two more 30secondcycles. In thiscasethe system will stopafter

a total of 3 cycles and rearm automatically, and then ignore only the open entry or

violatedsensor.When theentryisclosedorthesensorisreset,protectionwill begin

instantly for the formerly affected circuit.

Anytime the security system triggers, the Status Light will indicate which

protected zone triggered the system by flashing two, three or four times between

pauses, in the red color which indicates “alarm” operations. This “Zone Violation”

codewillcontinuetoflash,evenafterdisarming.The systemcan holdtwo different

violationcodes init'smemory,whichis clearedby turningtheignition switch"on".

Once the Crime Guard has been activated and reset, the disarming confirmation

changes to make the user aware that it has done so.

How the controller reacts: If the controller was previously used to arm or

operate the system, it will react to an alarm activation, provided it is within range

ofthesystem. Uponreceivingasignalfromtheactivatedsystem,thecontrollerwill

start chirping, and an icon will start flashing, indicating which protected zone’s

violation caused the system’s alarm condition.

The controller will continue the chirping for 15 seconds, or until any of its buttons

applicationsisbeingused to sound the vehicle’s existing horn. This featurechanges

only the primary audible output, so that it can be utilized to sound the existing

horn by itself. This is for cases when the programmable relay is desired for other

features, such as unlocking the doors, or as an additional ignition or accessory

output should it be needed for the remote starting operation.

The Steady Siren setting is exactly that- a steady output which the electronic

sirenrequires. Whenprogrammingthis feature for using the output for thevehicle’s

horn, the optional setting produce pulsed output on the system’s siren wire, in

three different pulse timings, which allow a degree of customization of the horn’s

sound during the alarm activation.

Page - 36

Feature #16 Alarm Functions Bypass

Factory Default Setting Off (press “disarm/unlock” button to program)

Option: On (press “arm/lock” button to program)

This feature converts the system into a strictly Remote Keyless Entry System by

eliminating all antitheft alarm-oriented operations and features. When this feature

is programmed on, the 850i5has remote keyless entry and engine starting opera-

tion only.

Feature #17 Ignition Activated Anti-Carjacking Protection

Factory Default Setting Off (press “disarm/unlock” button to program)

Option: On (press “arm/lock” button to program)

This form of Anti-Carjacking is initiated by the ignition key being turned on. The

Anti-Carjacking protection, and the three ways to initiate it are described on page

25.

Feature #19 Remote Activated Anti-Carjacking Protection

Factory Default Setting Off (press “disarm/unlock” button to program)

Option: On (press “arm/lock” button to program)

This form of Anti-Carjacking is initiated by a signal from the controller or

transmitter. The Anti-Carjacking protection, including the three ways to initiate it

are described on page 25.

Feature #18 Door Activated Anti-Carjacking Protection

Factory Default Setting Off (press “disarm/unlock” button to program)

Option: On (press “arm/lock” button to program)

This form of Anti-Carjacking is initiated by a door being opened. The Anti-

Carjacking protection, including the three ways to initiate it are described on page

25.

Feature #20 Open Door Warning Upon Arming

Factory Default Setting Off (press “disarm/unlock” button to program)

Page - 10

There are two methods of disarming the Crime Guard:

Disarming the System

Disarming the System Using

the Controller or Transmitter

2- The second method is an “Emergency Override” alternative, should the

controlleror transmitter becomelost or inoperable. Thismethod uses theValet

Switch, but the vehicle’s ignition key is also required.

1- The primary method is to use the controller or transmitter by pressing and

releasing its “disarm/unlock” button. This is the normal “daily use” method.

Press and release the controller or transmitter “disarm/unlock” button

oncetoinstantlydisarm thesystem,disengagingthestarterinterruptandunlockthe

doors. If you have the optional unlock driver's door feature installed, then upon

disarming only the driver's door will unlock, and if the “disarm/unlock” button is

pressed again at anytime thereafter, all of the doors will unlock.

Thesystem’sreaction: Disarmingisconfirmedbythesirenchirping twice,the

StatusLight turning off,andthe parkinglightsflashing twice,thenwith the interior

lights illuminating for 30 seconds for approach illumination. The lights will turn

off instantly if the ignition switch is turned "on" before the 30 seconds expires.

If the controller was used: It will confirm by chirping twice (or four times if

the system was activated), showing “DISARM” icon and “unlocked lock”, and

is pressed. Which button being pressed has these effects upon the triggered Crime

Guard system:

• Pressing “arm/lock” will rearm the system, stopping both system’s alarm

condition (leaving it armed), and stop the controller’s chirping.

• Pressing “disarm/unlock” will disarm the system, leaving the doors locked,

stopping both system’s alarm condition (leaving it disarmed) and the

controller’s chirping. Pressing the button a second time unlocks the doors.

• Pressing and releasing any of the three other buttons will simply stop the

controller’s chirping, but leave the security system still sounding in its

alarm state.

The controller will continue to display the flashing icon indicating the violated

zone, while the system is disarmed, until the ignition switch is turned on.

Prewarning Detection Circuit: When the sensor is triggered by a light impact

orshocktothevehicle,thesecuritysystemwillrespondbychirpingthesiren3times

and locking the doors. After this Prewarning circuit has been triggered five times

it will automatically shutdown until the alarm system is disarmed, then armed.

Ifthecontrollerwasusedtoarmthesystemandprewarningoccurs,ifinrangeitwill

react by chirping 3 times and showing the “impact” starburst icon on its display.

Feature #12 Parking Light Illumination Upon Disarm

Factory Default Setting On (press “arm/lock” button to program)

Option: Off (press “disarm/unlock” button to program)

Thisfeatureaffectstheparkinglightoperationwhenthesystemisdisarmed. When

this feature is turned on, the parking lights flash once, and then turn back on for

externalillumination for 30seconds unlesstheignitionkeyis turnedon duringthat

time. If this feature is turned off, the parking lights flash once only, and do not

illuminate. ThisfeatureonlyaffectstheCrimeGuard’sparkinglightoperation,and

not the interior light operation.

Feature #13 2nd Channel Also Disarms System

Factory Default Setting On (press “arm/lock” button to program)

Option: Off (press “disarm/unlock” button to program)

“2nd channel” is most commonly used to remotely open the vehicle’s trunk, in

which case the alarm should also disarm. This feature, turned on, configures the

systemtodisarmwhenthe2ndchannelisused. Ifturnedoff,the2ndchanneloutput

will still occur, with 2 chirps, but without the parking light flashes; and if armed,

the system will not disarm.

Feature #14 3 or 45 Second Arming Delay

Factory Default Setting 3 Seconds

(press “arm/lock” button to program)

Options:

15 Seconds (press “disarm/unlock” button to program)

30 Seconds (press “II” button to program)

45 Seconds (press “III” button to program)

Whenthesystemisarmed,whetherbythecontroller,transmitterorbyanautomatic

feature,there isabrief periodoftime inwhicha systemactivation, or alarm,cannot

occur. This Arming Delay allows the system to completely process its sensory

parameters, which can include the vehicle to stabilize. In some cases more time is

needed than the factory-set 3 seconds, and this feature offers three longer delay

options.

Feature #15 Steady Siren or Pulsed Horn

Factory Default Setting Steady Siren

(press “arm/lock” button to program)

Options:

Pulsed Horn Low (press “disarm/unlock” button to program)

Pulsed Horn Medium (press “II” button to program)

Pulsed Horn High (press “III” button to program)

It is important to understand that the Crime Guard has a primary audible output,

for the electronic siren; and that it also has a programmable relay which among its

Page - 35

Page - 11

Safety Disarm/Storm Mode: While the system is activated, i.e. sounding the

siren and flashing the lights, pressing the “disarm/unlock” button will disarm the

system,butnotunlockthedoors. Thissafetyfeatureensuresthatthevehicleremain

secureshould thesystemrequiredisarmingdue tobeing activatedfromnuisance or

malicious false sensory inputs, such as typically produced by severe weather

conditions. Toremotelyunlockthedoorsifthesystemis disarmedwhile activated,

simply repeat the disarm operation by pressing and releasing the “disarm/unlock”

button again. If disarmed from a panic mode, the normal disarm indications are

present, including the unlocking of the doors.

AutomaticRearmingFeature:AutomaticRearmingisaprogrammablefeature

which ensures that your system is never inadvertently disarmed. It is possible to

accidentally or unknowingly operate the controller or transmitter from a pocket or

purse. You may not even be aware of an accidental disarming due to the enhanced

operatingdistanceofferedbytheCrimeGuard’s extendedrange,orifthecontroller

confirmation is not noticed. Automatic Rearming has the alarm rearm itself 90

secondsafteritishasbeendisarmed,unlessavehicledoorisopenedandtheignition

key turned on. Automatic Rearming is confirmed by a fast flashing Status Light

afterthedisarming,unlessthesystemwastriggered,inwhichcaseaZoneViolation

code will flash instead.

During the 90 second period, Automatic Rearming can be paused by opening

the door or stopped completely by turning the ignition key "on". Also, Automatic

Rearmingcanbe cancelledbythe SafetyDisarm/StormMode feature;ifthe system

is disarmed while triggered, Automatic Rearming will not occur.

If the Crime Guard was activated and reset itself: The disarming

confirmation will no longer be 2 siren chirps, and the parking lights flashing twice

before staying on with the interior lights. Instead, the system will respond with 4

siren chirps and the parking and interior lights flashing 4 times before staying on

for 30 seconds. The Status Light will change to flashing two to four times in red

between pauses as a “Zone Violation” code to indicate which protection circuit

triggered the system (2 flashes, hood/trunk; 3 flashes, doors; 4 flashes , impact

sensor). Thesespecialaudibleandvisualdisarmingindications,andZoneViolation

code, will remain this way until the ignition key is turned “on”.

Disarming the System by Emergency Override

Shouldthetransmitterbecomelost,damaged,oritsbatteriesbecomeexhausted,

the Valet Switch and the vehicle’s ignition key may be used to disarm the system:

Step 1 With the system in the armed condition, enter the vehicle via the driver's

door (be aware that the alarm will trigger when the door is opened).

briefly showing the number of operating controllers or transmitters.

Off (press “disarm/unlock” button to program)

Chirps Excepting Valet Mode (press “II” button to program)

Chirps in Valet Mode Only (press “III” button to program)

This feature removes the system’s 1 arming and 2 disarming confirmation chirps.

When this feature is used to remove these chirps, the system will still have 3 chirps

upon arming if a protected zone is violated, and still have 4 chirps upon disarming

if the system was previously activated. Using this feature to turn off the arm and

disarming chirps will also not affect the Prewarning operation, Unauthorized

Transmitter Alert (if used), nor will it affect the chirps used when programming.

The other two settings will have the confirmation chirps operate only when the

system is inValet Mode, and nototherwise; or, the chirps willoperate except when

the system is in Valet Mode.

Page - 34

Feature #10 Confirmation Chirp Volume

Factory Default Setting Medium High

(press “II” button to program)

Options:

Low (softest) (press “arm/lock” button to program)

Medium Low (press “disarm/unlock” button to program)

High (loudest) (press “III” button to program)

This feature allows the choice of four different volume levels of the system’s

confirmation chirps, and when programming it, the buttons can be repeatedly and

sequentially pressed, thus making it easy to hear and choose the setting with the

best chirp volume.

This feature operates regardless of how feature #15, “Steady Siren” or “Pulsed

Horn” is set. Feature #15 sets “Steady”; or “Pulsed” as three different timings, for

the activated alarm period output. This feature, #10, affects only the confirmation

chirps.

Feature #11 Alarm Duration

Factory Default Setting 30 Seconds

(press “arm/lock” button to program)

Options:

60 Seconds (press “disarm/unlock” button to program)

90 Seconds (press “II” button to program)

120 Seconds (press “III” button to program)

This feature allows four choices of the Alarm Duration, which is the period of time

for which the system sounding the siren (and/or horn, optionally) and flashes the

parking lights when it is triggered. Caution: Before lengthening the Alarm

Duration you should always check and determine if there are any local anti-

noise or nuisance ordinances in your area, to avoid the possibility of receiving

a violation citation.

Page - 12

The number of Valet Switch presses which are required for the Emergency

Override is custom-programmable! This is the SecureCode feature, which is

describedonpages19&20. TheaboveEmergencyOverrideinstructionsreflect

the “as received from the factory” default setting.

Step 3 Within 5seconds pressandrelease theValet Switch onetime. The system

will disarm.

Shouldyoufeelthreatened,ortheneedtoattractattention,youcanactivateyour

system's remote “Panic” feature at any time by pressing and holding for 3 seconds

the controller or transmitter’s “arm/lock”, the “disarm/unlock”, or the “III”

button. Your system will respond by sounding the siren and flashing the parking

lights for the normal activated alarm period of 30 seconds.

Additionally,theCrime Guardsystemfeaturesanunique“enhanced”remotePanic

operation,regardingadditionaloperationsduring Panic,and inassociationwiththe

transmitter button used in it’s activation or deactivation:

Remote Panic Feature

To disengage remote Panic, simply press and release any one of the same three

transmitter buttons, or, allow it automatically stop after 30 seconds.

• Activating Panic with the “III” button will not affect the system’s armed or

disarmed status; the doors locked or unlock condition; nor will it affect the

starter disable circuit.

• Activating it with the “disarm/unlock” button will unlock the doors, disarm

the system and does not engage the starter interrupt.

• Activating Panic with the “arm/lock” button will lock the doors, arm the

system and engage the starter interrupt.

• Deactivating Panic with the “arm/lock” button will stop Panic, and leave the

system armed with the starter interrupt engaged, and the doors locked.

• Deactivating it with the “disarm/unlock” button will stop Panic, and leave the

system disarmed with the starter interrupt disengaged, and the doors unlocked.

• If the system is allowed reset itself from remote Panic, it will enter the armed

state, locking the doors and engaging the starter interrupt, regardless of which

of the three buttons was used to activate it.

• Deactivating Panic with the “III” button will stop Panic, and leave the system

in the same state it was in at the moment Panic started, without locking or

unlocking the doors.

Ifdesired, itispossible tohave the“III”buttonoperate the3rdchannel outputor the

two optional further channel outputs, instead of remote Panic- see page 37.

Step 2 Using the ignition key, turn the vehicle’s ignition switch on. Feature #6 Doors Lock With Ignition On

Factory Default Setting On (press “arm/lock” button to program)

Option: Off (press “disarm/unlock” button to program)

This feature configures the system to automatically lock the vehicle’s doors every

time that the ignition switch is turned on. An exception to this would be if feature

#8 is turned on, and a door being open when the ignition switch is turned on. The

following feature #7 controls the automatic unlocking operations, and feature #8

providesforanoverrideofthisautomaticlockingifadoorisopenwhentheignition

is turned on.

Feature #8 Open Door Bypass of Ignition Locking

Factory Default Setting On (press “arm/lock” button to program)

Option: Off (press “disarm/unlock” button to program)

This feature cancels the automatic locking or unlocking of the vehicle’s doors

should one of the doors is open when the ignition switch is turned on or off.

Feature #7 Doors Unlock With Ignition Off

Factory Default Setting On (all doors will unlock)*

(press “III” button to program)

Options:

Off (press “arm/lock” button to program)

Driver’s Door Only* (press “disarm/unlock” button to program)

All Doors Except Driver’s Door* (press “II” button to program)

Similar to the previous locking feature, except this feature controls the unlock

operations when the ignition is turned off, and it has more options because of the

850i5’s multiple unlocking outputs.

*Multiple unlock outputs offer the capability of unlocking only the driver’s

door when the system is disarmed (Driver Door Priority Unlocking), and then the

option of unlocking all doors with a second press of the “disarm/unlock” button.

The driver’s door unlocking differently from the other doors must be config-

ured when the system is installed!

If the system is installed without the Driver’s Door Priority Unlocking

interface,this featureunlocksallofthedoorswhentheignitionswitchisturnedoff.

If Driver’s Door Priority Unlocking is installed, this feature can control only the

driver’sdoorunlockingwhentheignitionisturned,alldoorsunlocking,oralldoors

exceptthedriver’s. Thefollowingfeatureprovidesforanoverrideofthisautomatic

unlocking if a door is open when the ignition is turned off.

Feature #9 Confirmation Chirps

Factory Default Setting On

(press “arm/lock” button to program)

Options: Page - 33

YourCrimeGuard850i5systemofferstheultimateincomfortandconvenience-

remote engine starting. This feature allows the vehicle’s interior to be warmed in

the winter or cooled in the summer before you enter the vehicle. Simply leave the

climate controls set to the desired settings when leaving the vehicle prior to using

the remote starting feature.

The following pages explain the remote engine starting operations. If the

vehiclehasa manual transmission,aspecial procedure isrequiredwhen exiting the

vehicle to enable the ability to remote start. Otherwise, the actual activation of

remote start is the same for automatic or manual transmission vehicles.

Remote Engine Starting

Press and release together the controller or transmitter “arm/lock” and “disarm/

unlock” buttons.

How to Activate Remote Starting

The system’s reaction: The system will respond first by rapidly flashing the

Status Light in green color, then by turning on the ignition and flashing the parking

lights once. Then the starter will engage until the engine runs; 10 seconds later the

parking lights will illuminate steady during the period that the engine is running

from being remotely started. (having them flash instead is an option).

Theenginewillrunfor10minutes(thefactory-setperiod). A20minutesettingmay

be programmed, if desired, by referring to the “Programming Features” section.

Once the engine has been remotely started, to remotely stop it again press and

release together the transmitter’s “arm/lock” and “disarm/unlock” buttons. The

system will stop the engine, and extinguish the parking lights.

If the controller was used: If the controller is used to activate remote engine

starting, to confirm the operation it will first play a musical melody, and display

the “start” icon, which are puffs of smoke and appear behind the vehicle (5 differ-

ent musical melodies are programmable). Once the engine has started, when the

vehicle’s parking lights come back on the “start” icon’s puffs of smoke will change

to appearing sequentially.

When the engine stops running, whether by safety condition or controller com-

mand, a different musical melody is played, and the “start” icon disappears. If a

Page - 13

• When leaving the vehicle before remote starting, remember to set the climate

controls to the desired heating or air conditioning settings.

• If desired, the system’s alarm function may be armed or disarmed as needed

during remote start operations (the system must be disarmed before entering

the vehicle).

The remote engine starting feature should not be used when

the vehicle is parked in an enclosed structure or garage!

Feature #3 Automatic Rearming

Factory Default Setting Off

(press “arm/lock” button to program)

Options:

On without doors locking (press “disarm/unlock” button to program)

On with doors locking (press “II” button to program)

“Automatic Rearming”, described on page 11, prevents the system from becoming

accidentally disarmed by having it arm itself after being disarmed, if a door is not

then opened or the ignition turned on. Options are to have Automatic Rearming

operate with or without also locking the doors when the system does rearm.

Feature #4 Starter Interrupt Functions

Factory Default Setting Alarm Only

(press “arm/lock” button to program)

Options:

Off (press “disarm/unlock” button to program)

Automatic (press “II” button to program)

Alarm & Anti-Grind (press “III” button to program)

This feature controls the Starter Interrupt circuit, in several ways. In its default

setting,“AlarmOnly”, the Starter Interrupt isoperablewheneverthe alarm is armed.

The Starter Interrupt can also be used to prevent the accidental grinding of the

starter, by trying to start the vehicle when it is already running by remote starting

(as when the ignition key is turned to “run” to drive the vehicle).

The “Automatic” option will cause the Starter Interrupt output to automati-

cally engage 90 seconds after the ignition switch is turned "off", and also 90 sec-

onds after disarming the system. This automatic engagement will occur even if the

security system is in a disarmed state, but not if it is in Valet Mode. Once the

Starter Interrupt output is activated, the system must be armed, then disarmed with

the controller or transmitter, or placed into the Valet Mode by pressing and hold-

ing the Valet Switch for 2 seconds to disengage it. There are no Status Light

indications with this automatic form of Starter Interrupt.

Programming this feature off completely eliminates the Starter Interrupt out-

put, while leaving all other system operations fully functional.

Feature #5 Ignition Activated Override

Factory Default Setting Off (press “disarm/unlock” button to program)

Option: On (press “arm/lock” button to program)

This feature allows an activated system to be overridden and disarmed by simply

turning the ignition switch on within 10 seconds of the system’s activation. After

10 seconds, the Emergency Override must be performed or the controller or trans-

mitter “disarm/unlock” button can be used to disarm the system.

Page - 32

Page - 14

Should the engine fail to start on the first attempt, the system will subsequently

make as many as three further attempts, as needed. Please note that each starting

attempttakesapproximately20secondsforthesystemtocheckthevehicle’sstatus,

cycle the ignition and starter circuits, and then monitor vehicle status again before

the next attempt.

Safety Features: Certain conditions will prevent the engine from remotely

starting, or if remotely started already, will stop the running engine. These

conditions are:

✓A pressed brake pedal.

✓Thegearselector not being in the “park” or“neutral”position, or alternatively,

the parking brake not being set.

✓An open hood.

✓If manual transmission, the vehicle was entered or disturbed after the setup

procedure was performed.

Anopendoor will notpreventthe system fromstartingthe engine; if theenginehas

already been remotely started, opening a door will not stop the running engine,

unless the system is armed. Opening a door with the engine running by remote

control and the system armed will result in activating the system, which will stop

the running engine.

Todrivethevehicleawayafter remote starting, disarm the system (if needed) open

the door to enter the vehicle, insert the key into the ignition switch and turn the

switchto“on”or“run”position(not“start”!). Thenpressthebrakepedalorremove

thegear selectorfrom “park”;now theengineisnolongerrunningfrom thesystem,

but rather from the ignition key. To indicate this, the system will briefly sound the

siren. Pressing the Valet Switch will also turn off the system’s running the engine,

but without the violated safety circuit siren sounding.

Ifastartcommandissentfromthecontrollerortransmitter,butanyofthefollowing

conditionsarepresent,thesystemwillnotattempttostarttheengineandwillinstead

have a short sounding of the siren to indicate a violated safety circuit. The violated

safety circuit conditions which can produce this indication are the gear selector not

in the “park” position, an open hood or trunk, or a pressed brake pedal.

“Stick Shift” Remote Starting Setup Procedure: When the 850i5is in-

stalled into a manual transmission vehicle, Installer Programmable Feature #5 must

be turned on. Then, whenever remote starting will be desired at a later time the

safety circuit stops the engine, the “crossed out key” icon will momentarily appear

(but not if the transceiver’s command stops the engine).

If a safety circuit prevents the starting attempt, the “engine stopped” melody

will play, and the “crossed out key” icon will appear.

To custom program a new SecureCode:

Step 3 After entering the first stage by pressing the “arm/lock” button the

desirednumber oftimes,andreceivingachirpforeachpress,waitforthe

Step 2 Within10secondsslowlypressandreleasethecontrollerortransmitter’s

“arm/lock” button the number of times equal to the desired SecureCode

for stage 1, allow the system to respond to each controller/transmitter

button press with a siren chirp before pressing the button again.

Step 1 Follow Steps 1 to 4 in the previous “How to Program Features” instruc-

tions; at Step 4 the Valet Switch will be pressed and released once (the

siren chirps once) to access “feature #1”.

Feature #1 SecureCode

Factory Default Setting 1 Press

Options:

1 to 9 presses, in each of two stages

Step 4 Continue to configure stage 2 of the SecureCode by now pressing and

releasingthe“disarm/unlock”buttonthenumberoftimesdesiredforthe

stage2. Thisshouldbedoneintheexactsamefashionasthestage1entry-

pressthe“disarm/unlock”button,wait forasinglechirpbeforepressing

the button again, and then when final button press is done, wait after the

single chirp for the siren to chirp the total number entered Valet Switch

entry.

system, after the final button press, to chirp the siren again the total

number of times that the button was pressed.

Feature #2 Last Door Arming

Factory Default Setting Off

(press “arm/lock” button to program)

Options:

On without doors locking (press “disarm/unlock” button to program)

On with doors locking (press “II” button to program)

“LastDoorArming” hasthesystem automaticallyarmitself everytimeyou exitthe

vehicle(thecompleteoperationisdescribedonpages8&9). Thisfeatureturnsthat

operation on or off, and with options of having Last Door Arming operate with or

without also locking the doors when the system does arm.

SecureCode is a unique patented feature which allows you to custom select the

number of Valet Switch presses in two stages, instead of a single “1 press”, which

would be required in order to perform an Emergency Override. If any of the three

anti-carjacking features are utilized, a customized SecureCode would also be

required to turn it off once it is fully activated. The SecureCode operation is

described on pages 19 and 20.

Page - 31

Step 2 Press and release the controller or transmitter “arm/lock” and “disarm/

unlock” buttons together. The Status Light will begin flashing green, as

the 850i5is now keeping the engine running. Do not press the brake pedal

from this point, and the parking brake must remain on.

Step 3 Within 2 minutes, turn off the ignition key, exit the vehicle and then press

the transmitter’s “arm/lock” button to lock the vehicle. The alarm will

also arm, and the previously running engine will stop. The Status Light

also changes to show the “armed” indication, flashing slowly red, but

every fourth flash will be green, indicating that the system is “armed, and

ready for remote starting”.

Step 1 Withtheenginerunningandfootonthebrake,applytheparkingbrake,put

thetransmission shifterin“neutral”,andremove yourfoot fromthebrake.

following procedure must be performed before exiting the vehicle:

From this point, the vehicle may be remote started provided that it is not

disturbed. When ready to remote start, the activation of remote starting is the same

as previously described: press and release the transmitter’s “arm/lock” and

“disarm/unlock” buttons together.

During the setup procedure, the parking brake must remain set, and the regular

brake pedal must not be pressed when and after the transmitter’s “arm/lock” and

“disarm/unlock” buttons are pressed. After exiting the vehicle, the transmitter’s

“arm/lock” button only must be used to secure the vehicle. Using any other

transmitter button will produce the appropriate system response, but the remote

starting setup will be voided.

Once the system is fully setup for remote starting, it will start the engine if the

nexttransmitteroperationispressingthe“arm/lock”and“disarm/unlock”buttons

together. Ifanyothertransmitterbuttonis pressed the remote starting setup will be

voided. If the armed alarm should be triggered during this period, the remote

starting setup condition will be voided.

Pit-Stop Feature: This feature allows you to turn off the ignition switch, re-

move your keys, leave the vehicle and lock your doors while leaving the engine

running. To use this feature, have the engine running normally from the ignition

switch, have the gear selector in “park”, and your foot off of the brake pedal.

Press the Valet Switch twice; the parking lights will flash once and the siren chirps

5 times; then turn the ignition off. The engine will remain running for the pro-

grammed run time, or it will turn off if another controller or transmitter signal is

received, a safety circuit is violated, or if the Valet Switch is pressed.

This feature may be used anytime; it does not have to be specially programmed

to operate.

Page - 15

The User Programmable Features

Page - 30

Each of the Programmable Features is described in detail in the

following pages. The User Programmable Features are described as

a first group, and the Installer Programmable Features as a second

group. It is important to note that programmable features affect the

exact operation of the system, and that the descriptions of any

features utilized should be used to supplement the basic system

operationswhichweredescribedinprevioussectionsofthisbooklet.

This group of User Programmable Features are all accessed as a group in the first

level of features’ programming. These features have a direct affect upon the

system’s operations, so the programming and operation of each are described.

The Crime Guard 850i5’s 23 User Programmable Features:

1 SecureCode

2 Last Door Arming

3 Automatic Rearming

4 Starter Interrupt Functions

5 Ignition Activated Override

6 Doors Lock With Ignition On

7 Doors Unlock With Ignition Off

8 Open Door Bypass To Previous Two Features

9 Confirmation Chirps

10 Confirmation Chirp Volume

11 Activated Alarm Cycle

12 Lights On Upon Disarm

13 Disarm Alarm Upon Trunk Release

14 Arming Delay

15 Steady Siren Output / Pulsed Horn

16 Alarm Functions Bypass

17 Ignition Activated Anti-Carjacking Protection

18 Door Activated Anti-Carjacking Protection

19 Remote Activated Anti-Carjacking Protection

20 Open Door Warning Upon Arming

21 III Button Operation

22 Remote Start Run Time 10 or 20 Minutes

23 Steady / Flashing Lights During Remote Start

Usethestep-by-stepinstructionsontheprevioustwopagestochangeanyofthe

programmable features, along with the feature’s option choices and related

programming controller/transmitter button assignment found in the following

individual feature descriptions.

Other Controller and Transmitter Operations

The 2nd channel output, which is operated by pressing and holding the

controlleror transmitter “II”button for 1second,is designed specificallytooperate

yourvehicle’s electric powertrunk release. Yourvehiclewillrespondby releasing

the trunk lid or rear hatch, chirping the siren twice, turning on your parking and

To Silently Arm or Disarm the alarm, press and release the “II” button

twice. The siren’s confirmation chirps will not occur, and this operation simply

reverses, or “toggles” the armed and disarmed status that the system.

The sensor may be temporarily bypassed. When arming the alarm with

the controller or transmitter, within 3 seconds after the arming chirp press the “II”

button. The system will respond with another single chirp, confirming that the

sensor is bypassed.

Page - 16

Turbo Timer Feature: It is typically recommended that vehicles equipped with

turbocharged engines allow the engine to idle for a few minutes before turning it

off. When this Installer Programmable Feature is programmed on, the 850i5will

automatically keep the engine running as follows:

This feature must be programmed by the installer, and turning it on offers three

run time choices- 1, 2, or 3 minutes. The alarm may be armed while the engine is

running. Turbo Timer can be prevented form engaging, or “bypassed” if desired,

by turning the engine off first and then engaging the parking brake, or if it’s al-

ready engaged simply step on the brake pedal to turn the running engine off.

• With the engine running, hold the brake pedal and engage the parking brake.

When the brake pedal is released, the 850i5will keep the engine running for

the selected time, and then automatically turn it off.

Low Battery Automatic Starting Feature: This feature may be used any-

time. Setting this feature to operate has the 850i5automatically start the engine

should the vehicle battery voltage drop to 11 volts. This feature is very useful if

the vehicle is to parked unattended for a long period of time, such as extended

parking at the airport while away. Low Battery automatic starting must be acti-

vated for each occasion which it is desired to operate, as follows:

• Turn the ignition switch “on”, then “off” (engine not running), and within 7

seconds press the brake pedal. The system will chirp 6 times. Then, open the

door, exit the vehicle and close the door, press the transmitter’s “arm/lock”

button to lock the vehicle (arming the system).

The feature is now turned on, and until the system is disarmed or the ignition

turned “on”, if the system detects the vehicle battery voltage dropping to 11 volts,

it will automatically start the engine.

To Access a Feature:

Step 4 Within 10 seconds, Press & Release the Valet Switch the same num-

ber of times as the desired feature’s number.

•The siren will chirp and the Status Indicator Light will flash as

many times as the Valet Switch was pressed to indicate the feature

number which is now accessed.

•This and the following steps apply for both of the programming

levels- User Programming or Installer Programming.

To Change a Feature:

Step 5 After accessing the desired feature, within 10 seconds Press &

Release the appropriate controller or transmitter button.

•Pressing the “arm/lock” button typically turns the feature on; or sets

the feature’s first option. The siren will chirp once when this button

is pressed.

•Pressing the “disarm/unlock” button also typically turns the feature

off; or, sets the feature’s second option. The siren will chirp twice

when this button is pressed.

•Many features have third, and even fourth setting options. Pressing

the “II” and “III” buttons select these options. Confirmation chirps

when these buttons are pressed are three and four chirps respectively.

•Generally speaking, the Status Light will light solid when a selected

feature is programmed “on”, and not light when the feature is set for

“off”. Some features have more than one “on” option, in which case

the Status Light will remain on for all of the feature “on” settings.

To Access and Change further Features:

Step 6 If there are more features to be programmed, within 10 seconds of

the previous action Press & Release the Valet Switch the same

number of times as the next desired feature’s number.

•Again the siren will chirp and the Status Indicator Light will flash

as many times as the Valet Switch was pressed to indicate the new

feature number which is now accessed.

•Use the controller or transmitter as described in Step 5 to change the

newly accessed feature as desired.

•Repeat this Step 6 for each additional feature until all features are

programmed.

Step 7 Allow 10 seconds to pass without performing any programming

actions; or, turn the vehicles’s ignition on.

•The siren will sound briefly and the Status Indicator Light will go

out to confirm that the system is exiting Programing Mode.

Page - 29

The Crime Guard also has a 3rd channel output which is similar to the 2nd

channel, but it does have some special operational design differences. To operate

it, press and hold the controller or transmitter “II” and “III” buttons together for 1

second. Or, a programmable feature allows the pressing of the “III” button only to

operate this output.

The differences are that 3rd channel output will operate regardless of the

ignition switch being "on" or "off", and there is no audible or visual confirmation.

Connection of the 3rd channel will vary, depending upon the chosen application,

and may require extra parts or installation.

interior lights for 30 seconds, unlocking the doors, and disarming the system if it

wasarmed. The2ndchanneloutputwillnotoperatewhentheignitionswitchis"on"

unlessthevehicle'sdoorisopen. Ifdesired,thesecuritysystemcanbeprogrammed

to remain armed when this feature is used, and connection of the 2nd channel may

require extra parts or installation.

Thereare alsooptional4thchanneland5thchanneloutputs,whichare

available if more remote control functions are desired. These outputs can be

repurposed from two other system outputs, the factory arm and disarm outputs, by

an Installer Programmable Feature #9 (see page 42).

When these outputs are programmed to operate, pressing the transmitter or

controller“arm/lock”and“II” buttonstogetherwillactivatethe4thchanneloutput.

Pressing the “disarm/unlock” and “III” buttons will activate the 5th channel. Or,

if desired, the controller or transmitter “III” button can be programmed by User

Programming Feature #21 to operate any of these channels.

TheValetSwitchislocatedintheWindowUnit,oroptionally,theinstallermay

have mounted a separate Valet Switch in a hidden, yet accessible location. Please

ensure that you and others who use your vehicle are aware of the location of the

Valet Switch and its uses. The Valet Switch has several functions:

Using the Valet Switch-

Alarm Valet Mode & Starting Valet Mode

• It is also used in the procedures for programming features and programming

controllers or transmitters to operate the Crime Guard system. See the

“Programming sections of this manual for details on these uses.

• Should your controller or transmitter be lost or become inoperable, the Valet

Switch, and the ignition key, can be used to disarm the system with an

Emergency Override.

• Placing your system into Alarm Valet Mode, which prevents it from arming.

• Placing it into Starting Valet Mode, which prevents it from remote starting.

Page - 17

To a large extent the Crime Guard 850i5’s versatility is due to an incredible array

of programmable features- 33 main-system programmable features which offer

almost 100 choices of operational and interfacing options.

How to Program Features

To Enter Programing Mode and Change Features:

Page - 28

Foreasiermanagementofthe programmablefeatures,theyaredivided intotwo

separate accessibility levels. Features which allow the user to customize the

system’soperationaccordingtotheirown choice are in one group, and the features

which are installation related, or intended for the installer’s use are in a second

group. The 850i5system has 23 User Programmable Features, and there are 10

Installer Programmable Features.

ThevehicleignitionkeyandtheValetSwitchareusedtoentertheProgramming

Mode,thenthecontrollerortransmitteris usedtochangefeatures. Oncethesystem

is in Programming Mode, a 10 second period without programming activity will

cause the system to automatically exit Programming Mode. Features can be

selected in any order as desired.

Thesame basic“Features ProgrammingMode”isthe meansfor changingany

of the features; the mode itself can be accessed as either the User level, or the

Installer level.

•The siren will chirp then sound briefly and the Status Light will

flash to confirm that the system is entering Programing Mode.

•In the case of accessing the Installer Mode, the siren chirp then brief

sounding will be heard at the fifth valet press, and then again at the

tenth valet switch press.

•The Status Light shows red color for User Programming, and Green

color for Installer programming.

•In either Programming Mode, if 10 seconds of no programming

activity occurs, the system will exit Programming Mode. Program-

ming activity is the pressing of the Valet Switch or pressing a trans-

mitter button once a feature is accessed.

5 times for User Programming

10 times for Installer Programming

When the desired Programming Mode is accessed, select a Feature > > >

Step 3 Within 5 seconds, Press & Release the Valet Switch either:

Step 2 Turn the ignition off.

Step 1 Turn the vehicles’s ignition on.

Alarm Valet Mode: This allows you to turn off all of the “alarm” operations of

thesecuritysystemwhileretainingtheremoteconveniencefeaturessuchaskeyless

entry, Panic, and the Auxiliary Outputs. Remote starting is still operable, and has

itsownvaletmode(below). ThesystemmayonlybeplacedintoAlarmValetMode

when it’s disarmed; if armed, an Emergency Override must be performed before

placinginto AlarmValetMode. Oncethesystem isin AlarmValetMode, itcannot

become armed from the transmitter, Last Door Arming, or Automatic Rearming.

Alarm Valet Mode and Emergency Override are two similar, but different

procedures, although both operations use the Valet Switch, . Emergency Override

disarmsanarmedand activated system, and requires the ignition key. AlarmValet

Mode turns off the alarm operations of the disarmed system, but without the need

of the ignition key.

Alarm Valet Mode is designed for situations in which it is not convenient for

the security portion of the system to be operational, such as during extended

stopovers for vehicle servicing, maintenance, valet parking, washing, etc.

To Enter Alarm Valet Mode: With the system disarmed, and without pressing

the brake pedal, press and hold the Valet Switch for 2 seconds.

• The siren will chirp twice, the parking lights will flash twice and the Status

Light will illuminate solid red, then a series of green flashes, then return to solid

red. The green flashes, numbering from 1 to 6 times, is a remote starting diag-

nostic code (see page 21).

• To indicate that the system is in Alarm Valet Mode, the Status Indicator Light

remains solid red whenever the system is in Alarm Valet Mode.

• To remind the user that the system is in Alarm Valet Mode, the siren will

chirp once every time the vehicle’s ignition is turned off.

Page - 18

• The siren will chirp twice, the parking lights will flash twice and the Status

Light will illuminate solid green to confirm that the system is in Starting Valet

Mode.

• There is no audible reminder that the system is in Starting Valet mode.

To Enter both Modes (Full Valet Mode): With the system disarmed, press

and hold the Valet Switch for 4-6 seconds with the brake pedal in both conditions.

For example, start pressing the Valet Switch with the brake pedal unpressed; as

Starting Valet Mode: This feature is similar to Alarm Valet Mode, but its

purpose is turn off the remote starting operations of the system. The system may

be placed into Starting Valet Mode and Alarm Valet Mode independently, or into

bothmodesatthesametime. Pleasenotethattheonlydifferenceinobtainingeither

mode is whether or not the brake pedal is being pressed.

To Enter Starting Valet Mode With the system disarmed, and depressing the

brake pedal, press and hold the Valet Switch for 2 seconds.

If the Unauthorized Transmitter Alert feature is on, programming a

controllerortransmittertothesystemwillactivatetheUnauthorized

Transmitter Alert warning and the extended Status Light visual

display; for the next 48 hours the siren will sound a brief series of

chirps every time the vehicle’s ignition key is turned on. The

following special procedure programs the controllers/transmitters

and also turns the Unauthorized Transmitter Alert feature on.

Step 3 Press the “arm/lock” button on each remaining controller or transmitter.

The system will chirp the sirenonce to confirm that each was learned.

The controller or transmitter’s other three button's functions will

automaticallybeassignedwhenthe“arm/lock”buttonislearned. Ifacode

is not received within a 10 second period, the learning process will

automatically terminate, as indicated by another siren burst.

Step 2 Within5secondsofturningontheignition,presstheValetSwitch5times.

The siren will briefly sound, confirming that for the next 10 seconds the

system is ready to learn a controller/transmitter code. To enter a code,

simply press and release the “arm/lock” button (the button which is

designed to arm the system). When the first controller/transmitter code is

learned all existing stored codes will be erased.

Page - 27

Special Programming procedure to turn On the UTA feature: Usingthis

method to program controllers or transmitters, and to turn on or turn off the

Unauthorized Transmitter Alert feature.

Follow the same steps as the Standard Programming, but on any controller/

transmitterbeingprogrammedinsteadofpressing the“arm/lock”button,pressthe

“arm/lock” and the “disarm/unlock” buttons together. This action turns on the

UnauthorizedTransmitterAlertfeatureandatthesametimeprogramsthecontroller/

transmitter to operate the system.

Once the Unauthorized Transmitter Alert feature is turned on, the warning will

sound for 48 hours after any controller or transmitter programming, including the

programming session which was used to turn it on.

To Exit any of the 3 forms of Valet Mode, simply Press & Release the Valet

Switch at any time.

• The Status Indicator Light will turn off to confirm exit from either Alarm Valet

Mode, Starting Valet Mode, or both.

“SecureCode” allows the user to customize the number of Valet Switch presses

which are required to successfully perform an Emergency Override. The basic

EmergencyOverrideprocedureisdescribedonpages11-12. Insteadofasingle

“1 press” of the Valet Switch which would be required in order to perform an

Emergency Override, two stages of Valet Switch presses must be made. In each of

the two stages, the Valet Switch will need to be pressed 1 through 9 times, as

programmed by the user. This is the Emergency Override procedure if the system

has programmed with a customized SecureCode:

Step 1 With the system in the armed condition, enter the vehicle via the driver's

door(beaware thatthesystemwillactivatetoanalarmconditionwhenthe

SecureCode

Page - 19

soon as the two chirps are heard, press the brake pedal but do not release the Valet

Switch. As soon as a second set of two chirps is heard, the Valet Switch may be

released. The system is now in Full Valet Mode. It does not matter in what order

the pressed or unpressed brake pedal occurs.

• Once the system is in Full Valet Mode the Status Indicator Light will slowly

alternate green and red to confirm that the system is in Full Valet Mode. This

indication is present whenever the system is in Full Valet Mode.

• There will be the single chirp reminder every time the ignition turns off. This

is for the Alarm Valet Mode part of the Full Valet Mode condition.

Once the system is disarmed, if Valet Mode is desired, just press and hold the

Valet Switch for 2 seconds to place the system into Valet Mode. Should a mistake

bemade enteringtheSecureCode, aftera failedattemptto achieveSecureCode,the

ignition switch must be turned off, then on again before another attempt is made.

door is opened).

Step 2 Using the ignition key, turn the vehicle’s ignition switch on.

Step 3 Within 5 seconds press and release the Valet Switch the same number of

times that have been programmed for stage #1.

Step 4 After a few seconds, the siren will stop sounding, chirp once, and then

resume sounding.

Step 5 Now,within5secondspressandreleasetheValetSwitchthesamenumber

of times that have been programmed for stage #2. Within a few seconds

the siren will stop sounding, and the unit will disarm.

Page - 26

UnauthorizedTransmitter AlertTM is a protectionfeaturewhich maybeturned

onbytheuser (seethenextsection,“HowtoProgramControllersandTransmitters”).

When this protection feature is utilized, whenever a controller or transmitter is

added to operate the system, for 48 hours afterward a warning consisting of a brief

series of siren chirps sounds every time the vehicle’s ignition is turned on.

Also during this 48 hour warning period, the 10 second Automatic Transmitter

Verification visual display will increase to being displayed for 90 seconds instead

of 10 seconds. When this feature is used and activated, after 48 hours the warning

chirpsdisappearandtheStatusLightflashingtransmitter/controllernumberreturns

to being displayed for 10 seconds.

Automatic Transmitter VerificationTM shows the total number of controllers

and/or transmitters which can operate the system, by flashing the Status Light with

this number for 10 seconds every time that the ignition key is turned on. When a

controller is used to operate the system, as part of its confirmation the number of

operating controllers and transmitters is also displayed on its icon screen.

The Crime Guard 850i5features several security safeguards in one of the most

vulnerable areas of any remotely controlled system. These features are found in

both 2-way controllers and 1-way transmitters.

Controller and Transmitter Protection

Code JumpingTM It is quite easy, with the proper equipment, to record an alarm

or keyless entry system’s transmitter signal, and simply play the captured signal

back to the system to defeat it. Crime Guard’s Code Jumping renders such “code

grabbing” devices useless by randomly changing each signal that the controller or

transmitter sends.

The Crime Guard 850i5system is capable of being operated by as many as four

controllers or transmitters; these can be any combination of 1-way transmitters or

2-way controllers. Regardless of which, the transmitter or transceiver must be

encoded, or programmed, to the system in order to operate it (excepting the

originals, which were programmed at the factory).

The programming procedure is identical for a transmitter or for a controller.

Also, it is during the controller/transmitter programming procedure that the

Unauthorized Transmitter Alert feature may be turned on.

How to Program Controllers or Transmitters

Step 1 Have all controllers and/or transmitters which are to operate the system at

hand. Turn the ignition “on”.

StandardProgramming: Usingthismethodtoprogramadditionalorreplacement

controllers or transmitters does not affect Unauthorized Transmitter Alert.

ShouldtwofailedSecureCodeattemptsbemade,the systemwillignoreanyfurther

presses of the Valet Switch for two minutes.

In addition to Emergency Override, if any of the three anti-carjacking features

are utilized, a correct customized SecureCode would also be required to turn off

anti-carjacking once it has become fully activated. How to program your own

customized SecureCode is explained on pages 29, 30 and 31.

The Status Light

The Status Light visually confirms the status of the system and provides a high

level of visual deterrence. Two colors are shown- Red for security operations, and

Green for remote starting operations. Combinations of both colors are seen when

the two operations are occurring together. The Status Light is in the window unit,

and actually consists of two LED lights, with identical operation, for maximum

visibility.

Security System Status: The Red colored operations of the Status Light

indicate the status of the security system:

1) Off =Thesecuritysystem is disarmed and not performingautomaticfunctions.

The remote starter system is off, but in standby mode.

2) On Red Constant = The security system is in the Valet Mode, with the remote

starter system off and in standby mode.

3) Flashing Slow Red = The security system is fully armed, with the remote starter

system off and in standby mode.

4) Flashing Fast Red = Last Door Arming or Automatic Rearming is in progress,

with the remote starter system off and in standby mode.

Page - 20

Automatic Transmitter Verification: For the first 10 seconds after the

vehicle’signitionisturnedon,theStatusLightwillflashRedanumberoftimesthat

equal the number of controllers or transmitters that are capable of operating the

system:

5) 1 Red Flash /pause = 1 transmitter is programmed.

6) 2 Red Flashes /pause = 2 transmitters are programmed.

7) 3 Red Flashes /pause = 3 transmitters are programmed.

8) 4 Red Flashes /pause = 4 transmitters are programmed.

ZoneViolation:Ifthesystementers analarmcondition,theStatusLightwillstop

flashing slow Red and begin to flash in sequence to indicate which protected zone

caused the alarm condition. The Status Light will flash and pause to indicate which

protected zone was violated while the system is still armed, after it’s disarmed, and

until the vehicle’s ignition is turned on. The system’s Zone Violation feature’s

memory can store two consecutive zone violations. If there have been multiple

Step 2 Turning the ignition back on.

Page - 25

Anti-Carjacking Protection

The Crime Guard is equipped with three separate Anti-Carjacking protection

features, whose operation may be selectively activated by the ignition, by an open

door, or by the transmitter. All three are programmable, and must be turned on to

operate. Once activated, the user has 53 seconds to cancel the Anti-Carjacking

protection process by pressing the Valet Switch once. If Anti-Carjacking is not

cancelled,53secondsafterbeingactivatedthesirenwillbegintochirpfor7seconds

to alert the user that the system is about to enter into an alarm condition. The Valet

Switch may still be pressed once during this period to cancel the Anti-Carjacking

process.

If the Anti-Carjacking process is not cancelled before the 60 second count-

down expires, the system will enter an alarm condition, sounding the siren and

flashing the parking lights. 30 seconds after this occurs, or should the ignition be

turned off in the meantime, the stater interrupt will engage. Once the system

enters the alarm condition, it will not respond to the transmitter, nor will the sys-

tem reset automatically after 60 seconds, and it can only be disengaged by:

Step 1 Turning the vehicle’s ignition off.

Step 3 Within 5 seconds, perform an Emergency Override using the Valet

The three types of Anti-Carjacking protection features are:

Switch. If the SecureCode has been customized, the correct number of

Valet Switch presses must be made.

Anti-Carjacking protection activated using a controller or transmitter

hastheprocess start by pressingandholding the “III” button for3seconds, but only

if the vehicle’s ignition is on. The Valet Switch must be pressed within 60 seconds

afterthisisdonetocancelAnti-Carjacking.ThisisUserProgrammableFeature#19

(see pages 28,29, and 36).

Anti-Carjacking protection activated an open door has the process start

should a door be opened after the vehicle is started and the engine is running. The

Valet Switch must be pressed within 60 seconds after the door is opened to cancel

Anti-Carjacking. This is User Programmable Feature #18 (see pages 28,29, and

36).

Anti-Carjacking protection activated by the vehicle’s ignition has the

process start every time the vehicle’s ignition is turned on. The Valet Switch must

be pressed within 60 seconds every time the vehicle is started to cancel Anti-

Carjacking. This is User Programmable Feature #17 (see pages 28,29, and 36).

This manual suits for next models

Table of contents

Other Omega Car Alarm manuals

Omega

Omega Excalibur AL-700LC User manual

Omega

Omega Crime Guard 745i3 User manual

Omega

Omega MAX-E User manual

Omega

Omega K9-Classic-E User manual

Omega

Omega Crime Guard 750i5 User manual

Omega

Omega Executive ClassicOne User manual

Omega

Omega Freedom 400 User manual

Omega

Omega RS-310-EDP User manual

Omega

Omega Excalibur AL-1920-EDP User manual

Omega

Omega REC-12 Quick start guide

Omega

Omega Excalibur AL-1000ATV2 User manual

Omega

Omega Excalibur AL-1000-EDP User manual

Omega

Omega Freedom 500 User manual

Omega

Omega Freedom 200+2 User manual

Omega

Omega MAX-E Owner's manual

Omega

Omega Excalibur RS-X70 User manual

Omega

Omega Excalibur AL-1000-E User manual

Omega

Omega K9-Mundial Instruction Manual

Omega

Omega Comfort Start Product guide

Omega

Omega Executive 3000atv User manual

Omega

Omega Excalibur AL-1000SH User manual

Omega

Omega OL-BLADE-AL-CH6 User manual

Omega

Omega Excalibur AL-1510-EDP User manual

Omega

Omega Excalibur AL-1610-EDP User manual

Popular Car Alarm manuals by other brands

CompuSTAR

CompuSTAR 1WSHR user manual

Code Alarm

Code Alarm Procomp owner's guide

Directed Electronics

Directed Electronics Viper 4704 installation guide

Easyguard

Easyguard EC003 User Manual & Wiring Diagram

CYCLOPS

CYCLOPS PARALYSER 165 User instructions

iDataLink

iDataLink ADS-DL-CH6 install guide

Clifford

Clifford 980074 SERIES 11CX user guide

ENFORCER

ENFORCER 300C owner's manual

Marksman

Marksman M3a installation manual

Cobra

Cobra 3198 User instructions

Black Widow

Black Widow BW 4150 owner's manual

By Firstech

By Firstech MA580 installation guide

Bosch

Bosch IVS-SLIM instruction manual

Code Alarm

Code Alarm ca6355E owner's guide

Vapormatic

Vapormatic VLC5501 user manual

Fortin

Fortin EVO ONE THAR-ONE-TOY3 Electrical Wiring Manual

Directed Electronics

Directed Electronics 591XV installation guide

Viper

Viper 5900 owner's guide

Omega Crime Guard 850i5 User manual

Popular Car Alarm manuals by other brands