Omega RS-310-EDP User manual

COPYRIGHT 2007: OMEGA RESEARCH & DEVELOPMENT, INC.
Omega
RS-310-EDP
OPERATION MANUAL
FRONT COVER
PRINTER’S NOTE:
production front cover
is color; this is a
place marker cover.
ProductsmanufacturedandsoldbyOMEGARESEARCH&DEVELOPMENT,
INC. (the "Company"), are warranted to be free from defects in materials and
workmanship under normal use. If a product sold by the Company proves to be
defective,theCompany willrepairor replaceitfree ofchargewithin thefirstyear
and thereafter all parts to be repaired will be free with only a nominal charge for
Omega'slaborandreturnshipping,totheoriginalownerduringthelifetimeofthe
car in which it was originally installed.
All products for warranty repair must be sent postage prepaid to Omega
Research & Development, Inc., P.O. Box 508, Douglasville, Georgia 30133, or
send via UPS to: 981 N. Burnt Hickory Rd., Douglasville, Georgia 30134, with
billofsale or other dated proof of purchase. Thiswarrantyis nontransferable and
doesnotapply to any product damaged by accident,physicalor electrical misuse
or abuse, improper installation, alteration, any use contrary to its intended
function, unauthorized service, fire, flood, lightning, or other acts of God.
This warranty limits the Company's liability to the repair or replacement of
theproduct.TheCompanyshallnotberesponsibleforremovaland/orreinstallation
charges, damage to or theft of the vehicle or its contents, or any incidental or
consequential damages caused by any failure or alleged failure of the product to
function properly. UNDER NO CIRCUMSTANCES SHOULD THIS
WARRANTY,ORTHEPRODUCTCOVEREDBYIT,BECONSTRUED
AS A GUARANTEE OR INSURANCE POLICY AGAINST LOSS. The
Companyneitherassumesnorauthorizesanypersonororganization tomake any
warranties or assume any liability in connection with the sale, installation, or use
of this product.
This device complies with F.C.C Rules part 15. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference
and,(2) Thisdevicemust acceptany interferencethatmay bereceived, including
interference that may cause undesired operation.
The manufacturer is not responsible for any radio TV interference caused by
unauthorizedmodificationstothisequipment.Suchmodifications couldvoid the
user’s authority to operate the equipment.
L I M I T E D L I F E T I M E W A R R A N T Y
Omega Research and Development, Inc.
P. O. Box 508
Douglasville, Georgia 30133
www.caralarm.com 07/08 MO-RS-310-EDP REV0
BACK COVER
PRINTER’S NOTE:
production back cover
is color; this is a
place marker cover.

This device complies with FCC Rules part 15. Operation is subject to the
following two conditions, (1) This device may not cause harmful inter-
ference and, (2) This device must accept any interference that may be
received, including interference that may cause undesired operation.
The manufacturer is not responsible for any radio or TV interference
caused by unauthorized modifications to this equipment. Such modifica-
tions could void the user's authority to operate the equipment.
Omega Research and Development, Inc. www.caralarm.com
Page - 2
Coin batteries used in the transmitter which is used to operate this
security system may contain Perchlorate Material - special handling
may apply. See www.dtsc.ca.gov/hazardouswaste/perchlorate
Page - 19
Complete Programmable Features Matrix
USER Features Ignition on, off, then press Valet Switch 5times (BLUE Status Light).
# Feature Lock Button Unlock Button Trunk Button Start Button
1 Remote Start Run Time 10 Min. 5 min. 15 min. 20 min.
2 Steady/Flash Lights Rem. Start Steady Flashing
3 Confirmation Chirps/Volume Low Loud On Demand/Loud OFF
4 Pulsed Horn / Steady Siren Pulsed Lo Pulsed Med. Pulsed Hi Steady Siren
5 Doors Lock With Ignition On ON OFF
6 Doors Unlock With Ignition Off ON OFF
INSTALLER Features Ignition on, off, then press Valet Switch 10 times (BLUE Status Light).
1 Remote Start Activation Pulses 1 2 3 4
2 “Tach Wire” or “Tachless “ Tachless Tach Data Tach
3 Gasoline or Diesel Engine Gasoline Diesel
4 Sat. Port Green Wire Function Starter PulseAfter Start PulseAfter Stop Accessory Output
5 Ext. Starter Cranking Time .7 (minimum) 1.25 1.75 2.5 (maximum)
6 Doorlock Functions .8 second 3 Seconds Double Unlock Total Closure
7 Turbo Timer OFF 1 min. 2 min. 3 min.
Table of Contents
Introduction/SystemOverview................................................ 3-5
Valet Switch Overview ................................................................ 4
Transmitter Overview................................................................... 4-5
Using the RS-310-EDP System............................................... 5-9
Locking The Doors....................................................................... 5
Unlocking The Doors ................................................................... 5
Trunk Release/2nd Channel ......................................................... 6
Remote Starting ............................................................................ 6
Panic Mode................................................................................... 7
Other Transmitter Functions ........................................................ 7
Using The Optional ECHO 2-Way Upgrade ............................... 7
Using The Valet Switch .......................................................... 8
Valet Mode ................................................................................... 8
Emergency Override ..................................................................... 8
Pit-Stop Feature............................................................................ 8
Other Remote Start Features ................................................... 9
Low Battery Automatic Starting .................................................. 9
Turbo Timer Feature .................................................................... 9
Status Light Functions ............................................................. 9-10
Transmitter Protection............................................................. 10
How to Program Transmitters ................................................. 11
How to Program Features........................................................ 12-13
User Programmable Features .................................................. 13-14
Installer Programmable Features............................................. 15-18
Complete Programmable Features Matrix .............................. 19
Limited Lifetime Warranty .............................................. Back Cover
- IMPORTANT -
TheRS-310-EDPhasmanyprogrammablefeatureswhichcanoffer
moreoperationsthan those describedinthe basic system instruc-
tions. Mostly, these extra features and operations are configured
at the time of installation. Please read the sections of this manual
which explain programmable features, and consult your installer
forspecificsonhowyoursystemisconfigured,andforinstallation
options which can be added to system after installation.

Page - 3Page - 18
Welcome to the convenience which is offered by your RS-310-EDP
keyless entry & remote start system. The RS-310-EDP is designed and
manufactured by Omega Research and Development, a world leader in
vehicle convenience and security since 1975. Your system offers easy,
carefree operation, and the modular design allows its many impressive
featurestobecustomizedtosuityourneeds. Omegasystemsaredesigned
for professional installation, and are available only through new car retail
outlets and selected mobile electronics specialist dealers.
Please note that this guide is written to reflect:
- That a power doorlock interface is installed with your system
(the RS-310-EDP also operates your power doorlocks). The type
of interface may vary from one vehicle to the other, and in some
cases may involve optional components.
- That the RS-310-EDP operating the vehicle's existing horn is
an available option.
- That the Programmable Features are in the default settings;
the operations of these features are also explained.
Your RS-310-EDP system has three principal user components: the
Blue LED Status Light, the Valet Switch, and the Remote Transmitter.
Introduction
The Valet Switch is used to access Valet Mode, which allows the
operator to suspend some of the security system's normal functions for as
long as desired. The Valet Switch may also be used, instead of the remote
transmitter,tooverridealockedsystem. TheValetSwitchisalsousedwhen
programming remote transmitters and system features. See “Using the
Valet Switch” on page 8.
The Blue LED Status Lights informs you at a glance which of the
different conditions the system is in, and also serves as a visual deterrent
to break-ins and theft. Specific operations of this light are described on
pages 9-10.
Transmitters are used to operate the RS-310-EDP. Each system is
capable of being operated by up to four different remote Transmitters. The
remote transmitter has four push-button switches, each being labeled with
an icon as to function.
However, a popular upgrade option is the Echo 2-way controller. The
Echo, in addition to operating your system, also receives signals from the
system, and displays a variety of system conditions on its LCD screen. A
section of this booklet describes operating the RS-310-EDP with the Echo.
Feature #7 Turbo Timer
Factory Default Setting: Off (press “lock” button to program)
Options:
Run 1 Minute (press “unlock” button to program)
Run 2 Minutes (press “trunk” button to program)
Run 3 Minutes (press “start” button to program)
This feature when turned on configures the RS-310-EDP to automatically keep the
engine running briefly after it is turned off. This operation is designed specifically
for vehicles having turbocharged engines (the user may temporarily bypass the
feature if desired).
This feature should only be programmed by the installer, and the operation of
this feature depends on the correct connection of the safety wire to the vehicle’s
parkingbrake. Please referto the“Black/Whitewire” inthe installationmanualfor
the proper connection of this important wire.
• The second setting (programmed by the “unlock” button) changes the
lock and unlock outputs to be a longer 3 second pulse output. This is for certain
vehicles which require a longer output pulse from the system’s control unit;
typically cars having vacuum pump systems, although the longer setting is also
more suitable in some newer vehicles.
• Somenewervehiclesrequireadoublepulseoutputtoremotelyunlockthedoors
and/or to disarm a factory-equipped security system, which is what the Double
Pulse Unlock setting provides (it is programmed by the “trunk” button ). The
lock output pulse, in this setting, is 0.8 second.
• The Total Closure Lock Output (programmed by the “start” button) may be
usedwithvehicleswhichareoriginallyequipped withthe total-closurefeature.
Typically, a total closure feature is when locking the vehicle’s doors if the key
in the door is held to “lock” for a period of time the vehicle will close all
windows and the sunroof, in addition to locking the doors.
Selecting this feature setting changes the system’s door lock output pulse from
a0.8 second to aslongas a 28 secondduration output. The unlock outputis0.8
seconds in this setting.
Note: When this feature is turned on, during the 28 second period after arm-
ing the system, the lock output can be stopped on demand by pressing the
“lock” or “unlock” button. Only the output will stop- pressing
either button again will normally operate the system, and at any time after the
28 second lock output period ends.

Page - 4 Page - 17
The Window Unit With Status Light & Valet Switch
Valet
Switch
Status
Light
• TheValetSwitch isused intheprocedure ofprogramming operational
features and also for encoding transmitters to the system. A complete
description of the Valet Switch and its operations is on page 8.
The Blue Status Lights report the operational status
ofthesystemat alltimes,andalsoserves asavisual
deterrentto break-insand theft. Specific description
ofthe Status Light operationmay be foundon pages
9-10.
The Valet Switch has three main functions:
• The Valet Switch can be used to turn off the
remoteenginestartingfunctionsofthesystemplacing
it in “Remote Start Valet Mode”.
• TheValet Switch can also be used,in conjunction
withthevehicle’signitionkey,toperformanemergency
override when the system is in a “locked” state. This
is used in the event the transmitter is lost or becomes
inoperable. This is referred to as “performing an
Emergency Override”.
One of the components, typically mounted on the windshield, is the
Window Unit module which contains the Status Lights and the Valet
Switch. The window unit also receives communications from the system’s
remote transmitters.
The Transmitter & Basic Functions
“start” button
“trunk” button
“lock”
button “unlock”
button
Transmitter part numbers:
147-03 buttonsw/ text, chrome finish
147-03B buttons w/ icons, black chrome finish
Transmitter battery replacement:
Remove the small screw from the
lower back case, and separate the
transmitter case halves. Replace the
CR2032 (or 2 CR2016 batteries) coin-
type battery and reassemble the transmitter.
Feature #5 Extended Starter Cranking Time
Factory Default Setting: Minimum (.7 Second)
(press “lock” button to program)
Options:
Medium Lo (1.25 Second) (press “unlock” button to program)
Medium Hi (1.75 Second) (press “trunk” button to program)
Maximum (2.5 Second) (press “start” button to program)
Extended Starter Cranking Time operates in conjunction with the feature #2’s
“Tachless” setting. When the system is set for “Tachless”, this feature sets the
duration of the starter output for the 1st start attempt. If the engine doesn’t start on
the first attempt, the system will retry up to 3 more times. With each attempt, the
output will be extended by 0.2 seconds. There are four different base starter output
settings. While the default-set minimum is sufficient for most vehicles; the
Extended Starter Cranking Time can be used for difficult-to-start engines. This
feature should only be programmed by the installer.
ThisfeaturechangestheoperationoftheGreenwire(negative)onthesatelliterelay
port. This gives you the flexibility to accomodate certain vehicles that require any
out-of-the-ordinary pulses or remote start timing.
• ThefirstsettingoperatesasasecondarySTARToutput.Thiswillhavethesame
pulse timing as the large Violet wire on the main harness.
• The second setting will give a 0.8 second pulse immediately after the large
Violet wire’s output stops.
• Thethirdsetting will give a 0.8 secondpulseimmediatelyafter the remote start
shuts down by any means.
• ThefourthsettingoperatesasasecondaryACCESSORYoutput.Thiswillhave
the same operation as the large Orange wire on the main harness. This fea-
ture should only be programmed by the installer.
Feature #6 Doorlocking Functions
Factory Default Setting: 0.8 Second Lock & Unlock Output
(press “lock” button to program)
Options:
3 Second Lock & Unlock Output (press “unlock” button to program)
Double Pulse Unlock Output (press “trunk” button to program)
Total Closure Lock Output (press “start” button to program)
This single feature gives the installer several needed options, to match the RS-310-
EDP’s doorlocking outputs to suit different vehicle requirements.
• The first setting (programmed by the “lock” button) has the system
produce both the lock and unlock outputs as 0.8 second in duration. This is the
most common form of output needed, which interfaces most vehicles.

Page - 5Page - 16
“lock” button
• Pressing and releasing the “lock” button locks the doors.
• Pressing and holding this button for three seconds will first lock, then
activate the Panic feature.
“unlock” button
• Pressing and releasing the “unlock” button unlocks the doors
• Pressing and holding this button for three seconds will first unlock,
then activate the Panic feature.
”trunk” button
• Pressing the “trunk” button for two seconds will activate the “2nd
channel” output, for an optional function such as trunk release.
• Pressing and releasing this button twice, locks or unlocks the system
without confirmation chirps.
”start” button (red)
• Pressing&releasingthe“start”buttononcewillactivatetheremotestart
feature. Pressing it again, during remote start, will stop the engine.
Using The RS-310-EDP System
THE PARKING
LIGHTS WILL FLASH
ONCE
THE DOORS WILL LOCK
To Lock the Vehicle's Doors:
Press & Release the transmitter LOCK button
•The parking lights flash once to confirm locking, and
optionally, the horn will chirp once. The Status Light
will flash approximately once per second to indicate
that the system is in a LOCKED state.
Feature #2 “Tach Wire” , “Tachless”, or “Data Tach”
Starter Operation
Factory Default Setting: Tachless (press “lock” button to program)
Options: Tach Wire (press “unlock” button to program)
Data Tach (press “trunk” button to program)
This feature selects the RS-310-EDP processor’s method of determining the status
of the engine running during remote start operation. As explained in feature 5’s
description, “Tachless” mode has an associated base starter output time duration.
However, if the voltage fluctuation is detectable, the processor adjusts the starter
output time accordingly. When this feature is set for “Tach Wire” operation, the
base starter output increases to a maximum of 3 seconds, but the processor adjusts
the actual starter engagement time accordingly. Connecting and use of the “Tach
Wire” is the most reliable form of engine running information input, and its use is
recommended. Important: Before this feature is programmed, please refer to the
“Violet/White wire” section of the installation manual for proper wiring connec-
tion, and the Tach Learning Procedure. The “Data Tach” setting operates just like
the “Tach Wire” setting except it takes its reading from the D2D data port. Use of
this setting is determined by whether or not this feature is provided by the Databus
Interfacemodule.Ifso,theViolet/WhitewireisnotneedednoristheTachLearning
Procedure Required. Thisfeatureshould only be programmed by the installer.
Feature #3 Gasoline Or Diesel Engine
Factory Default Setting: Gasoline (press “lock” button to program)
Option: Diesel (press “unlock” button to program)
Thisfeaturechanges the system's timingofthe ignition and starteroutputsequence
forremotelystartingvehicles with gas or diesel engines. When set for gasoline,the
starteroutputwilloccur3secondsaftertheignitionsturnon.Also,whenthesystem
isin“Tachless”mode,theenginerunningstatuswillbedetermined10secondsafter
cranking. When set for diesel, the starter output will occur 20 seconds after the
ignitionsturnon to allow forglow plug warming. Also,whenthe system is running
in “Tachless” mode, the engine running status will be determined 40 seconds after
cranking. This allows the vehicle battery(s) to recharge properly and show normal
voltage levels due to the heavy drain diesel engines have on the electrical system
during cranking. This feature should only be programmed by the installer.
Feature #4 Satellite Relay Port Green Wire Function:
Factory Default Setting: Starter (press “lock” button to program)
Options:
Pulse After Engine Start (press “unlock” button to program)
Pulse After Engine Stop (press “trunk” button to program)
Accessory (press “start” button to program)
THE PARKING
LIGHTS WILL FLASH
TWICE THEN TURN
ON FOR 30 SECONDS
THE DOORS WILL UNLOCK
To Unlock the Vehicle's Doors:
Press & Release the transmitter UNLOCK button
• The parking lights flash twice then stay on for 30
seconds to confirm unlocking, and optionally the horn
will chirp twice. The Status Light will turn off to indi-
cate that the system is in an UNLOCKED state.

Page - 6 Page - 15
NOTE: The system has a horn/siren output though its connection is optional.
THE PARKING
LIGHTS WILL FLASH
TWICE THEN TURN
ON FOR 30 SECONDS THE DOORS WILL LOCK
THE PARKING
LIGHTS WILL TURN
ON
THE ENGINE WILL CRANK
To Activate Trunk Release/2nd Channel:
Press & hold the transmitter “trunk” button for 2 seconds
ToActivate/Deactivate Remote Start:
Press & Release the transmitter “start” button
•The parking lights flash twice then stay on for 30
seconds to confirm unlocking, and optionally the horn
will chirp twice. The Status Light will turn off to indi-
cate that the system is in an UNLOCKED state.
THE TRUNK WILL OPEN
•Within a few seconds the lights will turn off and the starter will engage.
•The engine will start, run, and the starter will be disengaged.
•The lights will turn back on and remain on while the system is control-
ling the engine. The status light will then continue to flash slowly.
•If the engine stalls, the system will make 3 more attempts to restart it.
•The parking lights will turn on and the
Status Light will flash fast to confirm the starting
process has begun.
•The sytem will then turn on the ignition circuit.
Feature #1 Remote Start Activation Pulses
Factory Default Setting:
1 pulse (press “lock” button to program)
Options: 2 pulses (press “unlock” button to program)
3 pulses (press “trunk” button to program)
4 pulses (press “start” button to program)
This feature allows you to choose the number of pulses required on the White/Blue
activation wire to activate the remote start feature. This allows you to activate the
remote start with external devices. For example, you can connect this wire to a
factoryinstalledkeylessentrysystem.Youcanrepurposethefactorylockbuttonso
thatmultiplepresseswillactivatetheremotestart.Withanyoftheoptionalsettings,
each 2nd, 3rd, or 4th pulse must occur within a 5 second window of the previous
pulse. This feature should only be programmed by the installer.
The Installer Programmable Features
Thesecond group of features,the Installer Programmable Features,are accessed as
the second level of features’ programming, which is pressing the Valet Switch 10
times instead of 5 times when entering Programming Mode (page 12). Caution:
Thesefeatureshaveacriticalaffectuponthesystem’soperations,andinmany
cases, also upon the system’s wiring connections. These features should
NEVERbechanged,exceptbytheinstallerorotherqualifiedprofessional. This
booklet should be consulted for the proper wiring connections, as associated with
these programmable features.
The Excalibur RS-310-EDP’s 7 Installer Programmable Features:
1 Remote StartActivation Pulses (White/Blue input wire)
2 “Tachless”,“Tach Wire”,or “DataTach”Starter Operations
3 Gasoline or Diesel Engine
4 Satellite Relay Port Green Wire Operations
5 Extended Starter Cranking Times
6 Doorlock Functions
7 Turbo Timer
Use the step-by-step instructions on page 12 to change any of the Installer
Programmable Features, along with the feature’s option choices and related
programming controller/transmitter button assignment found in the following
individual feature descriptions.
Installer Programmable Features should only be used by the original
or other qualified installer, AND individual Installer Features should
only be used, where applicable, with the correct wiring connections.
When you leave your vehicle, simply set the climate controls for what
you would like to have operating upon remote starting - the heater, de-
froster or air conditioning.
Upon entering the vehicle place the ignition key in the switch and turn it
to the "On" position, pressing the brake pedal will deactivate the remote
start operation. Do not turn the key to the "Start" position!
If you decide not to drive your car after remote starting, you can simply
press & release the “start” button again to deactivate the remote start.
Otherwise, the system will “time-out” and turn off automatically after 10
minutes. NOTE: If the horn honks when attempting to remote start, the
system is indicating that a safety circuit is violated. This could mean that
the hood is open, the gear selector is not in park, or that the brake pedal is
being pressed.

Page - 7Page - 14
THE PARKING
LIGHTS WILL FLASH
REPEATEDLY
THE DOORS WILL LOCK or
UNLOCK
To Activate Panic Mode:
Press & Hold the LOCK or UNLOCK button for 3 seconds
•The horn will sound, the parking lights will flash and
the doors will lock or unlock, depending on the trans-
mitter button used. To deactivate Panic, simply press
either the LOCK or UNLOCK button again.
OR
Feature #5 Doors Lock With Ignition On
Factory Default Setting: Off (press “unlock” button to program)
Option: On (press “lock” button to program)
This feature configures the system to automatically lock the vehicle’s doors every
time that the ignition switch is turned on. The following feature #6 controls the
automatic unlocking operations.
Feature #6 Doors Unlock With Ignition Off
Factory Default Setting: Off (press “unlock” button to program)
Option: On (press “lock” button to program)
Similar to the previous locking feature, except this feature controls the unlock
operation when the ignition is turned off.
Feature #3 Confirmation Chirp Function & Volume
Factory Default Setting: Low
(press “lock” button to program)
Options:
High (loudest) (press “unlock” button to program)
On Demand / High (press “trunk” button to program)
OFF (no chirps) (press “start” button to program)
This feature allows the choice of two different volume levels of the system’s con-
firmation chirps and the ability to turn OFF chirps or have them on demand. When
programming, the you can hear and choose the setting with the best chirp volume.
The “On Demand” setting allows you to lock and unlock the doors without chirps.
Pressing either function a 2nd time, will produce confirmation chirps.
Feature #4 Steady Siren or Pulsed Horn
Factory Default Setting: Pulsed Horn Low
(press “lock” button to program)
Options:
Pulsed Horn Medium (press “unlock” button to program)
Pulsed Horn High (press “trunk” button to program)
Steady Siren (press “start” button to program)
This feature changes only the audible output, in three different pulse timings, which
allow a degree of customizing of the horn’s sound during the alarm activation. The
Steady Siren setting is exactly that- a steady output which an optional electronic
siren would require.
Feature #2 Steady/Flashing Lights During Remote Start
Factory Default Setting: Steady (press “lock” button to program)
Option: Flashing (press “unlock” button to program)
This Feature configures the operation of the vehicle’s parking lights during the
remotestartoperation. Thedefaultsettingturnsontheparkinglightsduringremote
start; the other setting flashes the parking lights on and off during remote start.
Auxiliary Functions 1-4:
The actual operation of these functions will vary from car to car. They
aredesignedtooperateextravehiclefunctionslikeautomaticslidingdoors
or motorized hatches. Aux 1-4 are only available on certain vehicles when
thissystem isintegrated withthe vehicle’s datanetwork. Consultwith your
installing dealer to find out if any of these functions are available for your
vehicle. If so, confirm each operation with the transmitter and write each
function in the blank space provided below for later reference.
-Auxiliary 1 Function (___________________): To activate this
function,pressandreleasethe“trunk”and“start”buttonssimultaneously.
-Auxiliary 2 Function (___________________): To activate this
function,pressandrelease the“lock”and“trunk” buttonssimultaneously.
-Auxiliary 3 Function (___________________): To activate this
function, press and release the “unlock” and “start” buttons
simultaneously.
-Auxiliary 4 Function (___________________): To activate this
function, press and release the “unlock” and “trunk” buttons
simultaneously.
Other Transmitter Functions
Using The Optional ECHO 2-Way Upgrade
“start” button “P”rogram
button “unlock”
button
“lock”
button
“trunk”
button
Please refer to the
ECHO manual for
further explanation
of it’s capabilities.

Page - 8 Page - 13
Feature #1 Remote Start Run Time
Factory Default Setting 10 Minutes
(press “lock” button to program)
Options:
5 Minutes (press “unlock” button to program)
15 Minutes (press “trunk” button to program)
20 Minutes (press “start” button to program)
This feature sets the period of time that the engine will run after being remotely
started. If the engine is not stopped by controller/transmitter command or a safety
circuit violation, the engine will automatically stop upon the expiration of the
selected time period. Caution: The remote engine starting feature should
NEVERbeusedwhenthevehicleisparked inan enclosedstructureorgarage.
The User Programmable Features
- SEE PAGE 12 FOR PROGRAMMING INSTRUCTIONS -
Each of the Programmable Features is described in detail in the
following pages. The User Programmable Features are described as a
firstgroup,andtheInstallerProgrammableFeaturesasasecondgroup.
This group of User Programmable Features are all accessed as a group in the first
level of features’ programming. These features have a direct affect upon the
system’s operations, so the programming and operation of each are described.
The Excalibur RS-310-EDP’s 6 User Programmable Features:
1 Remote Start Run Time
2 Steady / Flashing Lights During Remote Start
3 Confirmation Chirps / Volume
4 Pulsed Horn / Steady Siren
5 Doors Lock With Ignition On
6 Doors Unlock With Ignition Off
Use the step-by-step instructions on page 12, and the complete features matrix
on page 19, to change any of the programmable features. Each feature, the option
choices and related programming controller/transmitter button assignment are
described in detail in the following pages.
Valet Mode
The system may be placed into a “valet mode” which prevents the
remote start feature from being activated. It also disables confirmation
chirps when locking or unlocking the doors. Valet Mode should always be
used when you do not wish for remote starting to be operated, such as
when you have your vehicle serviced.
The Valet Switch, is used to engage Valet Mode:
•With the system in an unlocked state, press and hold the Valet Switch
for 3 seconds; the Status Light will light steady, to indicate Valet Mode, and
stay illuminated continuously while the system is in Valet Mode. The horn
will chirp once and the lights will flash twice.
Once in Valet Mode, an attempt to remote start will result in no response
from the system. Keep this in mind if remote start stops functioning. The
system may have accidentally been placed in valet mode. To check for
valet mode, turn the ignition key to the RUN/ON position, then back OFF.
If the system is in valet mode, the horn will chirp once.
•To turn off Valet Mode, simply press & release the Valet Switch once.
The Status Light will turn off.
Using The Valet Switch
Emergency Override
If the system is in a locked state, you cannot perform some functions
like transmitter or feature programming. If the system is locked and you do
not have a transmitter to unlock the system, you can perform an emer-
gency override to access the programming functions.
•With the system in a locked state, simply turn the ignition key to the
RUN/ON position.
•Press and release the valet switch once.
You should now be able to access programming functions.
Pit-Stop Feature
This feature allows you to leave your vehicle and keep the engine run-
ning for quick errands. To use this feature, have the engine running nor-
mally from the ignition switch, have the gear selector in “park”, and your
foot off of the brake pedal. Press the Valet Switch twice; the parking lights
will flash once and the horn chirps 5 times; then turn the ignition off. The
engine will remain running for the programmed run time, or it will turn off if
another transmitter signal is received, a safety circuit is violated, or if the
Valet Switch is pressed.
Step 7 Allow 10 seconds to pass without performing any programming
actions, or turn the vehicle’s ignition on.
• The horn will sound briefly (and the Status Indicator Light will go out).

Page - 9Page - 12
Turbo Timer Feature
It is typically recommended that vehicles equipped with turbocharged
engines allow the engine to idle for a few minutes before turning it off.
When this Installer Programmable Feature is programmed on, the RS-
310-EDP will automatically keep the engine running as follows:
Low Battery Automatic Starting Feature
Setting this feature to operate has the RS-310-EDP automatically start
the engine should the vehicle battery voltage drop to 10.5 volts. This fea-
ture is very useful if the vehicle is to parked unattended for a long period of
time, such as extended parking at the airport while away. Low Battery
automatic starting must be activated for each occasion in which you desire
it to operate, as follows:
• Turn the ignition switch “on”, then “off” (engine not running), and within
7 seconds press the brake pedal twice. The system will chirp 6 times.
Then, within 5 seconds, exit the vehicle and press the transmitter’s
“lock” button to lock the vehicle.
The feature is now turned on, and until the system is disarmed or the igni-
tion turned “on”, if the system detects the vehicle battery voltage dropping
to 10.5 volts, it will automatically start the engine.
Other Remote Start Features
To Access and Change further Features:
Step 6 If there are more features to be programmed, within 10 seconds of
the previous action Press & Release the Valet Switch the same
number of times as the next desired feature’s number.
• Again the horn will chirp, the parking lights, (and the Status Indicator Light)
will flash as many times as the Valet Switch was pressed to indicate the new
feature number which is now accessed. Then use the controller or transmitter
as described in Step 5 to change the newly accessed feature as desired.
Programming Features
•The horn will chirp then sound briefly (and the Status Light will turn on) to
confirm that the system is entering Programing Mode.
•In the case of accessing the Installer Mode, the horn chirps then briefly sounds
at the fifth valet switch press, and then again at the tenth valet switch press.
•In either Programming Mode, if 10 seconds of no programming activity
occurs, the system will exit Programming Mode.
5 times for User Programming
OR
10 times for Installer Programming
Step 3 Within 5 seconds, Press & Release the Valet Switchch either:
Step 2 Turn the ignition off.
Step 1 Turn the vehicles’s ignition on.
Access a Feature:
Step 4 Within 10 seconds, Press & Release the Valet Switch the same num-
ber of times as the desired feature’s number.
•The horn will chirp, the parking light output will flash, (and the Status
Indicator Light will flash) as many times as the Valet Switch was pressed to
indicate the feature number accessed.
Change the Feature:
Step 5 After accessing the desired feature, within 10 seconds Press &
Release the appropriate controller or transmitter button.
• Pressing the “lock” button typically turns the feature on; or sets the
feature’s first option. The horn will chirp once and the parking lights will
flash once when this button is pressed.
• Pressing the “unlock” button also typically turns the feature off; or,
sets the feature’s second option. The horn will chirp twice and the lights will
flash twice.
• Many featureshavethird, andevenfourth settingoptions. Pressing the “trunk”
and “start” buttons select these options. Confirmation chirps when these
buttons are pressed are three and four chirps respectively.
• With the engine running, hold the brake pedal and engage the parking
brake. When the brake pedal is released, the RS-310-EDP will keep the
engine running for the selected time, and then automatically turn it off.
The turbo timer feature must be programmed by the installer, and turn-
ing it on offers three run time choices- 1, 2, or 3 minutes. The system may
be locked while the engine is running. Turbo Timer can be prevented from
engaging, or “bypassed” if desired, by turning the engine off first and then
engaging the parking brake, or if it’s already engaged simply step on the
brake pedal to turn the running engine off.
The Status Light
The Status Light helps to visually confirms the status of the system and
providesa high levelof visualdeterrence. The Status Lightis located inthe
window mount receiver unit.
Normal System Status
2) On Constant = The system is in the Valet Mode, with the remote starter
system disabled.
1) Off = The system is unlocked and the remote starter system is off, but
in standby mode.

Page - 10 Page - 11
5) Flashing Slow (after sending the remote start command) = The engine
is running via the remote starting system.
Starting System Status
The Status Light also indicates the remote start status:
4) Off = The remote starter system is off and in standby mode.
6) Flashing Fast (after starting the remote start sequence) = A remote start
command has been received, and the system is in the process of
starting the engine.
Remote Starting Diagnostics
Whenever the system is placed into Valet Mode, the Status Light
illuminatessolid. However, when thisfirst occurs, theStatus Light willflash
1 to 6 Green flashes before resuming solid illumination. This indicates why
the engine stopped running from the last previous remote starting attempt.
7) 1 Flash = Programmed run time expired.
8) 2 Flashes = Brake was pressed or hood opened.
9) 3 Flashes = Engine stalled or bad tach signal.
10) 4 Flashes = Received transmitter command to stop.
11) 5 Flashes = Gear selector removed from “park”.
12) 6 FLashes = Low voltage.
3) Flashing Slow = The system is locked, programming functions are
disabled and the remote starter system off and in standby mode.
Unauthorized Transmitter AlertTM (UTA) is a protection feature which
may be turned on by the user for added security (see “How to Program
Transmitters”). Whenthis feature isutilized, a warning consistingof a brief
series of horn chirps sounds every time the vehicle’s ignition is turned on.
The warning will operate for 48 hours. ATV also extends to 90 seconds.
Automatic Transmitter VerificationTM (ATV) shows the total number of
transmitterswhichcan operate thesystem,by flashingtheStatus Lightwith
this number for 10 seconds every time that the ignition key is turned on.
The Omega RS-310-EDP features several security safeguards in one
of the most vulnerable areas of any remotely controlled system.
Transmitter Protection
Code JumpingTM It is quite easy, with the proper equipment, to record an
alarm or keyless entry system’s transmitter signal, and simply play the
captured signal back to the system to defeat it. The RS-310-EDP’s Code
Jumping renders such “code grabbing” devices useless by randomly
changing each signal that the transmitter sends.
Step 1 Have all transmitters which are to operate the system at hand.
Then, turn the ignition “on”.
If the Unauthorized Transmitter Alert feature is on, programming a
transmitter to the system will activate the “UTA” warning and the
extendedStatusLightindication.Forthenext48hours,thehornwill
sound a brief series of chirps every time the vehicle’s ignition key
is turned on.
Step 3 Pressthe“lock”buttononeachremainingtransmitteroneatatime.
The system will chirp the horn once to confirm that each was
learned. The transmitter’s other three button's functions will
automatically be assigned when the “lock” button is learned. If a
codeisnotreceivedwithina10secondperiod,thelearningprocess
will automatically terminate, as indicated by another horn honk.
Step 2 Within 5 seconds of turning on the ignition, press the Valet Switch
5 times. The horn will briefly sound, confirming that for the next 10
seconds the system is ready to learn a transmitter/controller code.
Toenter a code, simply pressand release the “lock” button. When
the first code is learned all existing stored codes will be erased.
SpecialProgramming proceduretoturnOntheUTAfeature: Usingthis
methodtoprogramtransmittersoroptionalcontrollers,andtoturnonorturn
off the Unauthorized Transmitter Alert feature.
Follow the same steps as the Standard Programming, but on any
transmitter/controller being programmed instead of pressing the “lock”
button, press the “lock” and the “unlock” buttons together. This action
turns on the Unauthorized Transmitter Alert feature and at the same time
programs the transmitter or controller to operate the system.
Standard Programming: Using this method to program additional or
replacement transmitters does not turn on or otherwise affect the
Unauthorized Transmitter Alert (UTA) feature.
The RS-310-EDP system is capable of being operated by as many as
four transmitters. Additional transmitters must be programmed to the
systeminordertooperateit(theoriginals,wereprogrammedatthefactory).
ItisduringtheprogrammingprocedurethattheUnauthorizedTransmitter
Alert feature may be turned on.
How to Program Transmitters
Once the Unauthorized Transmitter Alert feature is turned on, the
warningwillsoundfor48hoursafteranytransmitterprogramming,including
theprogrammingsessionwhichwasusedtoturniton.Thisfeaturecanonly
be turned off again by sending the system back to Omega for a reset.