Omega K9 SUPER MUNDIAL-SS Instruction Manual

Page 1
Arming: P ress & Release the “Lock” button
Silent Arming: P ress & Release the Small “••” button Twice in 3 sec.
Disarming: P ress & Release the “Unlock” button
Silent Disarming: P ress & Release the Small “••” button Twice in 3 sec
Remote Control Quick Reference Guide
THE SIREN WILL
CHIRP ONCE
THE PARKING LIGHTS
WILL FLASH ONCE
THE DOORS WILL LOCK
(IF CONNECTED)
THE PARKING LIGHTS
WILL FLASH ONCE
THE DOORS WILL LOCK
(IF CONNECTED)
2 X
THE SIREN WILL
CHIRP TWICE THE PARKING LIGHTS
WILL FLASH TWICE
THE PARKING LIGHTS
WILL FLASH TWICE
THE DOORS WILL UNLOCK
(IF CONNECTED)
2 X
THE DOORS WILL UNLOCK
(IF CONNECTED)
Table Of Contents
Owner’s Guide
Arming the System ....................... 3
Disarming the System ................. 4
Emergency Override .................... 4
System Armed & Activated ........... 5
Panic ............................................ 5
Sensor By-Pass ............................ 5
Auxiliary Channel ......................... 6
3rd Channel .................................. 6
Remote Controlled Anti-Carjack ... 6
Anti-Carjacking ............................. 7
Valet Mode ................................... 8
LED Status Indicator .................... 8
Auxiliary Sensor & Prewarn .......... 9
Installation Instructions
How To Program Remote Control ............. 9
How To Program Features ...................... 10
Programmable Features .................. 10 - 12
Wiring Diagram ....................................... 13
Door Lock/Unlocking Systems ................ 14
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions, (1)
This device may not cause harmful interference and, (2)
This device must accept any interference received,
includinginterferencethatmaycauseundesiredoperation.
The manufacturer is not responsible for any radio or TV
interferencecausedbyunauthorizedmodificationstothis
equipment. Such modifications could void the user's
authority to operate the equipment.

Page 2
To Activate the Auxiliary Channel: P ress & Hold The Small “••”
Button for 3 Seconds
To Activate the 3rd Channel: P ress & Hold The Small “•••” Button
for 3 Seconds
To Activate Remote Anti-Carjack: (programmable feature # 10)
P ress & Hold the Small “•••” button, for 3 Secs, with the ignition “On”
Hold3seconds OperateRemoteStartUnit
OperateWindow Roll-Up Unit
Hold 3 seconds
OpenElectric Trunk
OperateWindow Roll-Up Unit
OperateRemote Start Unit
Hold3seconds
Emergency Override:
Panic: P ress & Hold the “Lock” Button for 3 Sec’s, with the ignition “Off”
Shock Sensor & Prewarn Bypass:
1) A rm the alarm by, Pressing & Releasing the “Lock” button
2) W ithin 2 seconds Press & Release the small “••” button.
THEN WITHIN
10 SECONDS
PRESS & RELEASE
VALET BUTTON
THE SIREN WILL SOUND THE PARKING LIGHTS
WILL FLASH
Hold 3 seconds
Then
2.
1.

Page 3
The system may be "Armed" by any of 3 methods:
1) Remote Control Arming: Press & Release the “Lock” button
Arming the Alarm
2) SILENT Remote Control Arming: Press & Release the Small “••”
button Twice within 3 seconds
UponArming: • The siren will chirp one time. (3 times if there is open zone)
• The parking lights will flash once.
• The doors will lock. (If an optional interface is connected)
• The starter interrupt will engage.
• The LED Status Indicator will begin to flash slowly.
-If azone isopen,(for examplea cardoor), whenarming, thealarmwill stillarm,
but will bypass the open zone until the zone is secured (siren will chirp 3 times).
3) To Passively Arm: Turn Ignition “Off”, Then Close all Doors.
Automatic“Last DoorArming”is aprogrammablefeature whichallows thealarm
to arm itself and, if desired, lock the doors upon arming.
If on, anytime the ignition is turned off, and then a door is opened and closed:
• The Siren will chirp once to confirm arming countdown has begun.
• The LED Status Indicator will begin to flash rapidly.
Thirty seconds later:
• The siren will chirp & the lights will flash once.
• The LED Status Indicator will begin to flash slowly.
• The starter interrupt will engage.
- The alarm is now fully armed. The doors will lock at this time, ifprogrammedto
do so, and if the vehicle is equipped.
- The system can not Last Door Arm if a protected zone is open. Should a ve-
hicledoor beopened duringthe armingcountdown, thecountdownwill stopand
startoveragain whenthedoor isclosed. AUTO REARM (programmable)allows
theAlarm to Rearm itself, if it is Disarmed and a vehicle door is not opened.
THE SIREN WILL
CHIRP ONCE THE PARKING LIGHTS
WILL FLASH ONCE
THE DOORS WILL LOCK
(IF CONNECTED)
THE PARKING LIGHTS
WILL FLASH ONCE
THE DOORS WILL LOCK
(IF CONNECTED)
2 X

Page 4
The system may be "Disarmed" by any of 3 methods:
1)RemoteControlDisarming: Press &Releasethe “Unlock” button
2) SILENT Remote Control Disarming:
Press & Release the Small
“••” button Twice within 3 sec
Upon Disarm: • The siren will chirp twice. (4 chirps if alarm has activated & reset)
• The parking lights will flash twice. (4 times if alarm has activated)
• The doors will unlock. (If an optional interface is connected)
• The starter interrupt will disengage.
• The LED Status Indicator begins flashing rapidly forAutomatic
Rearming, until alarm Rearms or a vehicle door is opened.
2-STAGE DISARM: IfDisarmingthealarmwhileitistriggered(sirensounding),the
first press of any remote control button will only silence the siren/horn. A second
press of the “Unlock” button will Disarm the alarm.
IMMOBILIZER MODE: If this mode is programmed “On”, the starter interrupt will
remainengagedafterthealarmisDisarmed,untiltheignitionisturned“On”andyou
Press & Release the Valet button. (Refer to programmable feature
#
5)
To Start Vehicle: .
1. Disarm the alarm, then Turn “On” the vehicle’s ignition
2. Press & Release the Valet Button.
Step 1: Withthesysteminthearmedcondition,enterthevehicleviathedriver's
door (be aware that the alarm will trigger when the door is opened).
Step 2: Using your key, turn the vehicle’s ignition to the "On" position.
Step 3: Within 10 seconds, Press & Release the Valet/ OverrideSwitch.
Disarming the Alarm
Emergency Override
THE SIREN WILL
CHIRP TWICE
THE PARKING LIGHTS
WILL FLASH TWICE
THE DOORS WILL UNLOCK
(IF CONNECTED)
THE PARKING LIGHTS
WILL FLASH TWICE
THE DOORS WILL UNLOCK
(IF CONNECTED)
2 X
THEN WITHIN
10 SECONDS

RegardlessofmethodusedtoArmthealarm,onceArmed,thealarmwillmonitor
all protected zones, and if an intrusion attempt is detected it will activate, or
“trigger”.
A trigger consists of the following:
• The electronic siren, or optionally the vehicle’s horn, will start sounding.
• The exterior parking lights will flash on and off repeatedly.
Anactivation hasa30 seconddurationunless thesystem is disarmedusing the
remotecontrol or theValet /Override switch.If allprotected zones aresecure at
theendof thetrigger,thesystem willstopandrearm itselftodetectfurther entry
attempts.Ifaprotectedzoneisstillopenattheendofthetriggercycle,thealarm
willcontinue tore-trigger itself forup tosix activatedcycles beforeit resets itself
and ignores the violated zone.
Should it be needed in a threatening situation, or you feel the need to attract
attention, the alarm can be triggered using the remote control. Your alarm fea-
tures “Panic Mode”, which allows you to activate “Panic” from the “Arm/Lock”
button.
To Activate Remote Panic: Press & Hold the “Arm/Lock” Button,
for 3 seconds, with the ignition “Off”.
The shock sensor & Prewarn zone can be by-passed using the remote
control. This may be useful in stormy weather.
1) Arm the alarm by, Pressing & Releasing the “Lock” button.
2) Within 2 seconds, Press & Release the Small “••” button.
- The siren will chirp once to confirm sensor has been by-passed.
- Upon Disarming the alarm, the sensor zone will reset.
Sensor By-pass
System Armed & Activated
Remote Panic Operation
Page 5
THE SIREN WILL SOUND
THE PARKING LIGHTS
WILL FLASH
Hold 3 seconds
Then
1. 2.

Page 6
TheAuxiliaryChannel maybe usedto operatean optional function. Possibili-
ties include remote trunk release, remote car starting, or an on-demand re-
mote window roll-up interface. Please see your Omega dealer for details on
availableoptions.
To Activate the Auxiliary Channel:
Press & Hold the Small “••” Button for 3 Seconds.
- The alarm will Disarm upon activating the Auxiliary channel.
- TheAuxiliary Channel cannot be activated if the vehicle's ignition is "On".
Theprogrammable 3rdChannel maybeused tooperate anoptional function,
suchas aremote startunit or an on-demandremote windowroll-up interface.
Please see your Omega dealer for details on available options.
To Activate the 3rd Channel:
Press & Hold the Small “•••” button for 3 Seconds.
- The 3rd Channel can be programmed to Supply a (-) output when the alarm
isArmed to operate a Window Roll-Up module (Programmable feature #12).
TheAnti-Carjacking mode can be activated using the remote control.
-
Refer to next page for sequence details. (programmable feature # 10)
To Activate Remote Anti-Carjack:
Press & Hold The Small “•••” Button, For 3 Seconds, With The Ignition
“On”.
The Auxiliary Channel
Hold 3 seconds
OpenElectric Trunk
OpperateWindow Roll-
Up Unit
OpperateRemote Start Unit
Hold3seconds OpperateRemote Start Unit
OpperateWindow Roll-
Up Unit
Remote Anti-Carjack
The 3rd Channel Auxiliary Output
Hold 3
seconds

Page 7
TheAnti-Carjacking sequencemay beactivated byany of3 methods:
1) Using the remote control, by holding down the Small “•••” Button for
3 seconds while the ignition is “On”. (programmable feature
#
10)
2)Whenadooris Opened whiletheignitionis“On” (programmablefeature
#
10)
3) Every time the ignition is turned “On”. (Programmable feature
#
9)
1)Anti-Carjackingactivatedusingthetransmitter: (programmablefeature#10)
The Anti Car-Jacking operation may be activated by pressing and holding the
remote control’s Small “•••” button for 3 seconds while the ignition is “On”.
2) Anti-Carjacking activated by an Open door: (programmable feature #10)
Ifprogrammablefeature#10is“On”,thesystemwillinitiatetheAnti-Carjacking
sequence every time a vehicle door is opened while the ignition is “On”.
3) Anti-Carjacking activated by the ignition: (programmable feature #9)
If programmable feature #9 is “On”, the system will initiate the Anti-Carjacking
sequence every time the vehicle’s ignition is turned “On”.
IMMOBILIZER MODE: If the “Immobilizer mode” is programmed “On”, the
ignitionactivatedanti-carjackingsequencewillbecancelledandthe“Immobilizer
mode” disarmed by: first turning “On” the vehicle’s ignition, then Pressing &
Releasing the valet button. (Refer to programmable feature
#
5)
Once the Anti-Carjacking sequence has begun, the user has 59 seconds to
press the Valet/Override Switch in order to cancel the sequence.
ORDER OFANTI-CARJACKING SEQUENCE:
- For first 20 seconds after the sequence has begun there are no signs.
- From 21-30 seconds, the LED will blink slowly.
- From 31-45 seconds, the LED will blink fast and the siren/horn will chirp
once every 2 seconds.
- From 46-60 seconds, the LED will blink fast and the siren/horn will chirp
once per second.
- If not cancelled yet, at 61 seconds the alarm will trigger.
In the triggered condition:
- The siren/horn will sound & The parking lights will flash.
- The starter interrupt will engage.
NOTE: Once theAnti-Carjack mode is triggered, the remote control will NOT
stop the operation, nor will the system reset automatically. Once it is trig-
gered, the Anti-Carjacking operation can only be deactivated by:
1) Turning the vehicle’s ignition “Off”.
2) Turning the vehicle’s ignition back “On”.
3) Within 10 seconds, Press & Release the Valet button.
Programmable Anti-Carjacking Protection

Page 8
Valet Mode
Valet Mode can only be entered into while the alarm is Disarmed.
ValetModeturnsoffallofthealarm’ssecurityfeatures,(includingAnti-Carjack).
ValetModeisdesignedforsituationsinwhichitisnotconvenientforthesecurity
portionofthealarmtobeoperational;forexampleduringextendedstopoversfor
vehicle servicing, loaning others your vehicle, maintenance, valet parking,
washing,etc. Theconveniencefeaturessuchaskeylessentrywillstilloperate.
To Enter Valet Mode (Alarm MUST be Disarmed):
Press & Hold the Valet Switch for 3 Seconds.
- TheLEDStatusIndicatorwilllightsolid Redandthesirenwill emitalongchirp
to confirm entry into Valet Mode. Now the system cannot becomeArmed.
- The vehicle's ignition may be "On" or "Off" when entering Valet Mode.
- To remind you its in Valet Mode ,The siren will chirp every time the vehicle’s
ignition is turned “Off”
To Exit Valet Mode:Simply Press & Release the Valet Switch.
- The LED will turn off and the siren will emit a long chirp to confirm that the
system has exited Valet Mode. Normal arming operations may be resumed.
- The vehicle's ignition may be "On" or "Off" when exiting Valet Mode.
The Red LED Status Indicator visually shows the status of the alarm and also
provides a high level of visual deterrence. The Red LED Status Indicator Light
isnormallymountedwhereit canbeseenbythedriver,as wellasfromoutside.
SecuritySystemStatus:TheprimaryfunctionoftheRedLEDStatusIndicator
Light is to indicate the normal operating status of the security system:
Off = The system is disarmed and not performing any automatic functions.
On Constant = The system is in the Valet Mode.
Flashing Slow = The system is fully Armed.
Flashing Fast (while Disarmed) = Last Door Arming or Automatic Rearming.
Zone Violation: Oncealarmis Disarmed,LEDwillshowwhich zonetriggered
alarm until the ignition is turned “On” (this clears unit’s memory).
2 flash & pause = Pin-Switch zone triggered alarm.
3 flash & pause = Door zone triggered alarm.
4 flash & pause = Sensor zone triggered alarm.
AutomaticTransmitterVerification: Forthefirst90secondsafterthevehicle’s
ignitionisturned"On",theLEDStatusIndicatorwillflashanumberoftimesequal
to the number of remote control transmitters which are programmed to operate
thealarm.Thisindicationcanbefrom1Flash/pauseupto4Flashes/pause,as
the system can be operated by just one, or as many as 4 remote transmitters.
The LED Status Indicator

Page 9
Auxiliary Sensor: This security system is equipped with a plug-in port for an
optionalsensortoincreasetheeffectivenessofthesystem. Thecomprehensive
lineofoptionalsensorsofferediscomprisedofimpactsensors,glasstampering
sensors, and microwave/radar sensors which can detect motion inside and
outside the vehicle.
Prewarning Detection: This circuit requires connection to a dual zone sensor
or detection device. When the sensor’s prewarn zone is triggered the siren will
emit a series of chirps.
To program remote controls to operate the alarm:
Step 1: Turn "On" the vehicle's ignition.
Step 2: Within 7 seconds press the Valet/Override Switch 5 times. The alarm
willwolfthesiren oncetoconfirmentry intoRemoteControlProgrammingMode.
Step 3: Within10seconds,pressanyButtononeach remoteto beprogrammed.
The siren will chirp to confirm each time a remote has been programed.
If10 secondsexpire withoutany programmingactivity,orif thevehicle’signition
is turned “Off”, the system will automatically exit Remote Control Programming
Mode. The siren will emit 2 long chirps to confirm exit.
NOTE: Up to 4 remote controls can be programed to operate the alarm. When-
ever a remote control, new or existing, is programmed to the alarm, all existing
codes are erased for security. So all remote controls which are to operate the
alarm, must be programmed in at the same time.
Immobilizer Mode: Immobilizer mode must be disarmed before entering
remote control programming mode. (refer to programmable feature
#
5)
1. Turn “On” ignition
2. Press & Release the Valet/Override button, (siren will chirp twice)
3. Press valet/override button 5 times to enter remote control programming
mode.
ATV: The LED Status Indicator will show the number of programmed remote
control transmitters for 90 seconds after the vehicle’s ignition is turned On.
As theinstructions aboveshow, programmingextra transmittersto anyvehicle
security system is easy; the exclusive patented ATV feature protects against
someone programming their own transmitter to operate your system.
Auxiliary Sensor & Prewarning
How to Program Remote Controls to the Alarm