Omega Excalibur AL-1920-EDP User manual

AL-1920-EDP
TOUCH
Touch Screen Color 2-way Alarm & Remote Start
Operation Guide
Temporary cover. Color cover is in a separate le.

2
Table Of Contents
Introduction................................................................................................................... 3
Controller & Transmitter Overview................................................................................ 4
The 2-Way Controller ............................................................................................... 4
The Controller Status Screen ................................................................................... 4
The 1-Way Transmitter ............................................................................................. 5
Controller & Transmitter Functions ............................................................................... 5
Other Remote Start Features ....................................................................................... 9
Low Battery/Low Temp Automatic Starting............................................................... 9
Turbo Timer Feature................................................................................................. 9
Pit-Stop Feature ..................................................................................................... 10
Manual Transmission Starting ................................................................................ 10
Security System Features .......................................................................................... 10
Last Door Arming.................................................................................................... 10
Automatic Rearming............................................................................................... 10
Pre-Warn Detection ................................................................................................ 10
When The System Triggers.....................................................................................11
Using The Valet Switch................................................................................................11
Emergency Override ...............................................................................................11
Valet Modes.............................................................................................................11
SecureCode ........................................................................................................... 12
The Status Light ......................................................................................................... 12
Multi-Car Operation & Vehicle Proles ....................................................................... 14
Multi-car operation.................................................................................................. 14
Programming the vehicle name.............................................................................. 14
Selecting car1 or car2 ............................................................................................ 14
Selecting the vehicle image.................................................................................... 14
Programming Controller Options................................................................................ 15
Selecting button beep, melody, & vibrate modes ................................................... 15
Clock & time options overview ............................................................................... 15
Setting the time & date ........................................................................................... 15
Setting the time format (12 or 24 Hour).................................................................. 16
Setting the alarm clock ........................................................................................... 16
Demo mode............................................................................................................ 16
LCD screen display options overview .................................................................... 16
Setting the screen on time...................................................................................... 17
Setting the screen brightness................................................................................. 17
Other Controller Functions ......................................................................................... 17
Viewing the alarm trigger history ............................................................................ 17
Power off mode ...................................................................................................... 17
Parking timer & remote start timer.......................................................................... 17
Anti-Carjacking Protection.......................................................................................... 18
Programming Controllers/Transmitters....................................................................... 19
Programming Features............................................................................................... 19
User Programmable Features .................................................................................... 20
Installer Programmable Features ............................................................................... 23
Programmable Features Matrix.................................................................................. 27

3
Introduction
Congratulations for choosing one of the most versatile, fully-featured vehicle secu-
rity and convenience systems available today. Omega Research & Development has
been a leader in vehicle security products for nearly 4 decades. Please take the time
to read this manual thoroughly so you can fully enjoy the benets and features this
system offers.
In this manual, you will primarily learn about 5 user interface components and how
they work together in alerting you to system changes as well as how you can control
system operations. Keep in mind that the operations described in this manual are writ-
ten to only reect the default system settings. Be sure to discuss any customization
with your installer so you can remember any variations from this guide.
Controllers: The system has a 2-way controller that, in addition to controlling the
system, it will give you conrmations on system operations as well as violation alerts.
A 1-way transmitter is also included. It is a standard remote control that still gives
you control over all features but without conrmations. The next section covers the
controllers’ operations in detail.
The Status Lights: These lights are built into the system’s window-mounted
antenna. They give you a visual indication of the system’s current state and provide
troubleshooting indicators. The operations of the status lights are covered later in this
manual.
The Valet Switch: This push button gives you access to system programming,
transmitter/controller programming, and valet functions. It is also built into the sys-
tem’s window-mounted antenna. The valet switch’s operations are also covered later
in this manual.
Flashing Lights: The system is connected to your vehicle’s parking lights to
provide a 360 degree visual conrmation, warning, & deterrence in almost all system
operations. Each operation described in this manual also includes the corresponding
indicator from the ashing lights. The ashing lights primarily provide visual deter-
rence when the system is violated.
Siren and/or Horn Sounding: The system includes an electronic siren that offers
conrmation chirps during daily operations and programming. It is also the primary
means of alerting anyone near your vehicle that the system has been violated. The
system is capable of sounding the vehicle’s horn in addition to, or in place of, the
electronic siren. Most system functions have a corresponding audible alert that is
described throughout this manual. Becoming familiar with these alerts will help you to
instantly understand any changes in the system’s status.

4
Controller & Transmitter Overview
Controller part number: 701-03
1) Antenna: Sends commands to the system and
receives conrmations for 2-way functions.
2) Touch Screen LCD: Displays all controller func-
tion buttons as well as the status of your system.
3) Home Button: This wakes up the controller
when the screen is off and returns you back to the
status screen.
4) Charger Port: This is where you plug in the
charger to recharge the controller’s battery.
5) Key Chain Loop: Use this loop to
attach the controller to your key chain.
1
3
5
4
2
THE 2-WAY CONTROLLER
Battery Level Indicator*
Clock/Timer
Current System State
Vehicle Image
(Selectable)
Alarm Clock ON icon
Vehicle Name
(Programmable)
CH2/CH3 Indicator
Remote Start ON/OFF Indicator
Melody/Voice Indicator
Vibration Mode Indicator
Lock/Unlock Indicator
Alarm Trigger Indicator
In Range Indicator
*The controller is powered by a built-in rechargeable battery. When the battery level
indicator shows a low battery, plug the supplied USB cable into the controller, then
connect the other end to the supplied AC adapter or your computer’s USB port. While
charging, the indicator will increment from empty to full. When full, the indicator will
show a “plug” icon.
THE CONTROLLER STATUS SCREEN

5
Controller & Transmitter Overview (cont’d)
“lock”
button
“trunk”
button
“unlock”
button
“start”
button
Transmitter part number: 148-03
Call your dealer or visit
www.caralarm.com to order replacement
transmitters.
Transmitter battery replacement:
Remove the small screw from the lower
back case, and separate the transmitter
halves. Replace the CR2032 battery (or
with 2 CR2016 batteries) and reassemble
the transmitter case.
THE 1-WAY TRANSMITTER
Controller & Transmitter Functions
SCREEN 1: To access, press the HOME button and tap the screen.
LOCK / ARM: Press and release the “LOCK” icon.
THE SIREN WILL CHIRP & THE PARKING LIGHTS WILL•
FLASH ONCE.
UPON RECEIVING CONFIRMATION FROM YOUR•
SYSTEM, THE CONTROLLER WILL PLAY THE LOCK/ARM
ANIMATION AND VOICE ALERT.
NOTE: PRESSING LOCK TWICE IN 5 SECONDS STARTS
THE PARKING TIMER. THE CLOCK WILL CHANGE TO
0:00 AND START COUNTING IN MINUTES & HOURS.
(1-WAY TRANSMITTER: PRESS THE LOCK BUTTON)
UNLOCK / DISARM: Press and release the “UNLOCK” icon.
THE SIREN WILL CHIRP TWICE & THE PARKING•
LIGHTS WILL FLASH TWICE THEN ILLUMINATE FOR 30
SECONDS.
UPON RECEIVING CONFIRMATION FROM YOUR•
SYSTEM, THE CONTROLLER WILL PLAY THE UNLOCK/
DISARM ANIMATION AND VOICE ALERT.
(1-WAY TRANSMITTER: PRESS THE UNLOCK BUTTON)

6
Controller & Transmitter Functions (cont’d)
TRUNK RELEASE / CHANNEL 2: Press and hold the “TRUNK”
icon for 3 seconds.
THE SYSTEM WILL DISARM AND THE TRUNK WILL•
OPEN.
UPON RECEIVING CONFIRMATION FROM YOUR•
SYSTEM, THE CONTROLLER WILL PLAY THE TRUNK
RELEASE ANIMATION AND VOICE ALERT
(1-WAY TRANSMITTER: PRESS AND HOLD THE TRUNK
BUTTON FOR 3 SECONDS)
REMOTE START: Press and release the “ ” icon twice within 5
seconds. (see user feature #21 for additional options)
THE PARKING LIGHTS WILL FLASH ONCE AND THE•
STATUS LIGHT WILL FLASH RAPID GREEN.
THE SYSTEM WILL TURN ON THE IGNITIONS AND•
PROCEED TO START THE ENGINE.
ONCE THE ENGINE IS RUNNING, THE PARKING•
LIGHTS WILL TURN ON AND STAY ON AND THE STATUS
LIGHTS WILL FLASH SLOW GREEN.
UPON RECEIVING CONFIRMATION FROM YOUR•
SYSTEM, THE CONTROLLER WILL PLAY THE REMOTE
START ANIMATION AND VOICE ALERT.
THE CLOCK WILL CHANGE TO 0:00 TO START THE•
REMOTE START TIMER. IT WILL TIME HOW LONG THE
ENGINE RUNS IN MINUTES & HOURS.
(1-WAY TRANSMITTER: PRESS THE START BUTTON
TWICE IN 5 SECONDS)
*
If the engine stalls, the system will make up to 3 more attempts.•
Each time you park your vehicle, set the climate controls to give you the de-•
sired interior temperature when you use the remote start.
The engine will run for the preset run time (see user feature #1).
Run Time Extender• : Press the “ ” icon one time while in remote start mode
to restart the engine run timer. The timer on the controller will restart at “0:00”.
NOTE: This can only be used once per remote start cycle. The controller will also give you
“run time expiration” warning (2 chirps) 1 minute before the remote start cycle ends.
If you decide not to drive your vehicle, you can turn off the remote start using•
the same method to turn it on (Default = press “start” twice in 5 seconds)
NOTE: If user feature #21 is programmed for 1 press, the 1st press = Run Time Extender so
an additional press is required.
Upon entering the vehicle during remote start mode, turn the ignition key to•
the “ON/RUN” position (NOT START!!). When you press the brake pedal, the
remote start will turn off allowing the ignition key to take over.
*
x2

7
Controller & Transmitter Functions (cont’d)
CHANNEL 3: Press and hold the “CH3” icon for 3 seconds.
YOUR SYSTEM WILL ACTIVATE THE CHANNEL 3•
OUTPUT.
UPON RECEIVING CONFIRMATION FROM YOUR•
SYSTEM, THE CONTROLLER WILL PLAY THE CHANNEL
3 ANIMATION AND VOICE ALERT.
(1-WAY TRANSMITTER: PRESS AND HOLD THE TRUNK
& START BUTTONS FOR 3 SECONDS)
SCREEN 2: To access, press the HOME button, tap the screen,
press the down arrow once.
CHANNEL 4 (IF EQUIPPED): Press and hold the “CH4” icon for 3
seconds.
YOUR SYSTEM WILL ACTIVATE THE CHANNEL 4•
OUTPUT.
THERE IS NO 2-WAY CONFIRMATION FOR THIS•
FUNCTION.
(1-WAY TRANSMITTER: PRESS AND HOLD THE LOCK &
TRUNK BUTTONS FOR 3 SECONDS)
CHANNEL 5 (IF EQUIPPED): Press and hold the “CH5” icon for 3
seocnds
YOUR SYSTEM WILL ACTIVATE THE CHANNEL 5•
OUTPUT.
THERE IS NO 2-WAY CONFIRMATION FOR THIS•
FUNCTION.
(1-WAY TRANSMITTER: PRESS AND HOLD THE UN-
LOCK & START BUTTONS FOR 3 SECONDS)

8
PANIC: Press and hold the “LOCK” or “UNLOCK” icon for 3
seconds.
THE SIREN/HORN WILL SOUND, THE PARKING•
LIGHTS WILL FLASH, AND THE DOORS WILL LOCK OR
UNLOCK DEPENDING WHICH ICON IS PRESSED.
(1-WAY TRANSMITTER: PRESS AND HOLD THE LOCK
OR UNLOCK BUTTON FOR 3 SECONDS)
Controller & Transmitter Functions (cont’d)
SILENT ARM / DISARM: Press and release the “TRUNK” icon
twice in 5 seconds.
THE PARKING LIGHTS WILL FLASH, AND THE•
DOORS WILL LOCK/ARM OR UNLOCK/DISARM DE-
PENDING ON THE CURRENT SYSTEM STATUS.
UPON RECEIVING CONFIRMATION FROM YOUR•
SYSTEM, THE CONTROLLER WILL PLAY THE LOCK/
ARM OR UNLOCK/DISARM ANIMATION AND VOICE
ALERT
(1-WAY TRANSMITTER: PRESS AND HOLD THE LOCK
OR UNLOCK BUTTON FOR 3 SECONDS)
SENSOR BYPASS: Press and release the “TRUNK” icon within 5
seconds of arming the alarm system.
THE SYSTEM WILL GIVE ONE CHIRP TO INDICATE•
THE SENSOR IS BYPASSED.
UPON RECEIVING CONFIRMATION FROM YOUR•
SYSTEM, THE CONTROLLER WILL ALSO CHIRP ONCE.
(1-WAY TRANSMITTER: PRESS AND RELEASE THE
“TRUNK” BUTTON WITHIN 5 SECONDS OF ARMING THE
SYSTEM)
THEN
x2
OR

9
AUXILIARY FUNCTIONS 1-4:
The actual operation of these functions will vary from car to car. They are designed
to operate extra vehicle functions like automatic sliding doors or motorized hatches.
Aux 1-4 are virtual outputs only available on certain vehicles when this system is
integrated with the vehicle’s data network. Consult with your installer to nd out if any
of these functions are available for your vehicle. If so, conrm each operation with the
controller and write each function in the blank spaces provided below.
- Auxiliary 1 Function (___________________): To activate this function, press
and release the “CH3” icon. (1-way transmitter: press and release the “trunk” and
“start” buttons simultaneously).
- Auxiliary 2 Function (___________________): To activate this function, press
and release the “CH4” icon. (1-way transmitter: press and release the “lock” and
“trunk” buttons simultaneously).
- Auxiliary 3 Function (___________________): To activate this function, press
and release the “CH5” icon. (1-way transmitter: press and release the “unlock” and
“start” buttons simultaneously).
- Auxiliary 4 Function (___________________): To activate this function, press
and release the “AUX4” icon. (1-way transmitter: press and release the “unlock” and
“trunk” buttons simultaneously).
Controller & Transmitter Functions (cont’d)
Other Remote Start Features
It is typically recommended that vehicles equipped with turbocharged engines
allow the engine to idle for after driving to cool the turbocharger. When this Installer
Programmable Feature (#4) is enabled, the system will automatically keep the engine
running as follows:
• With the engine running, hold the brake pedal and engage the parking
brake. When the brake pedal is released, the system will keep the engine running for
the programmed time (1, 2, or 3 minutes), and then automatically turn it off.
• The system may be locked while the engine is running. Turbo Timer can be
prevented from engaging, or “bypassed” if desired, by turning the engine off before
engaging the parking brake, or if it’s already engaged, step on the brake pedal to turn
the engine off.
This feature will automatically start the engine should the vehicle battery drop
below 11 volts or the interior temperature drop to 15 (or 32) degrees fahrenheit. This
feature is very useful when the vehicle is parked for a long period of time in cold
climates. You must activate these features each time you park your car to use them.
• Turn the ignition switch “on”, then “off” (engine not running), and within 7 seconds
press the valet switch twice. If there is a 2 second delay without additional valet but-
ton presses, the horn will honk 3 times activating low voltage start mode.
• To activate low temp starting, enter low voltage start mode as described above
but, before the horn honks, press the valet switch 1 time (15 degrees) or 2 times (32
degrees) within 5 seconds. The horn will honk to conrm your selection.
NOTE: When low temp start mode is activated, low voltage start is also activated.
These features will operate once every two hours until the ignition key is turned “ON”.
LOW BATTERY/LOW TEMP AUTOMATIC STARTING
TURBO TIMER FEATURE

10
PIT-STOP FEATURE
This feature allows you to leave your engine running for making quick errands. To
use this feature, have the engine running normally from the ignition switch and your
foot off the brake pedal. Press the Valet Switch twice; the parking lights will ash and
the horn chirps 5 times. Turn the key off and the engine will remain running for the
programmed run time.
MANUAL TRANSMISSION STARTING
Remote starting with a manual transmission requires a different installation method
and installer feature #5 must be turned on. Also, a setup procedure that ensures the
transmission was left in neutral must be performed each time you leave your vehicle
and intend to use remote start later. Perform these steps:
1) With the engine running, hold the brake pedal, apply the parking brake, then
release the brake pedal.
2) Use the transmitter as if you were activating remote start (default: press START
twice). The green status light will start to ash slow.
3) Turn off the ignition key and exit the vehicle.
4) Press LOCK on the transmitter. The engine will shut down (unless turbo timer is
on) and the status light will ash green every 2 seconds to indicate it is ready to be
remote started.
NOTE: Manual transmission starting is canceled if you enter the vehicle after
performing the setup procedure.
Other Remote Start Features (cont’d)
Security System Features
LAST DOOR ARMING
This system can be congured to arm automatically when all the vehicle’s doors
are closed (see user feature #2). When this feature is utilized, the siren/horn will chirp
once when all of the doors are closed. At that point, it will start a 30 second count-
down (indicated by a fast ashing status light). After 30 seconds, the system will arm
(and lock the doors if congured to do so). During the 30 second arming delay, if a
point of entry is opened, the countdown will pause until all entry points are closed
again. Turning ON the ignition key will cancel the last door arming sequence until the
key is turned off and the doors are all closed once again.
AUTOMATIC REARMING
This system can be congured to rearm automatically whenever the system is
disarmed (see user feature #3). When this feature is utilized, the system will start a
90 second (indicated by a fast ashing status light) countdown to arm the system
after using the controller to disarm/unlock the system. This is very useful for situations
when the controller may accidentally disarm/unlock the system. For example, if it’s
kept in a purse or pocket where other items could potentially press the buttons.
PRE-WARN DETECTION
This system’s impact sensor is designed, in addition to detecting a full impact, will
warn away potential violators when it detects a light impact to the vehicle. The system
will respond by chirping the siren/horn 3 times and locking the doors. This is very use-
ful when an intruder attempts to unlock the door with “slim jim” types of devices.

11
WHEN THE SYSTEM TRIGGERS
If the system were to be compromised while armed, it will trigger sounding the
siren/horn and ashing the parking lights for 30 seconds (programmable). At this point
you will also be notied on the controller as to which zone is violated (if in range of the
system). When disarming the system after a trigger event, the siren/horn will chirp 4
times and the parking lights will ash 4 times instead of the standard 2 times.
LOCK ON TRIGGER: If a door is opened when the system is triggered, it will wait
until the door is closed again, then lock the doors. This patented feature is useful to
further deny a thief of further access to the vehicle.
STORM SAFE MODE: When the system is triggered, pressing the “UNLOCK” icon
will stop the alarm from sounding but will leave the doors locked. This function is use-
ful if you have a false triggering situation due to violent weather.
ZONE VIOLATION RECALL: The system is capable of telling you which zones were
triggered last. In addition to the controller’s trigger history log (discussed later in this
manual), the system’s status light will ash to indicate which zone was triggered. This
occurs during the alarm cycle AND after disarming. The system will store the last trig-
gered zone until the vehicle’s ignition key is turned on. See “The Status Light” section
of this manual for further explanation of this feature.
NUISANCE PREVENTION: If the system prewarns 5 times within 15 minutes, it will
bypass the zone for the remainder of the 15 minutes before rearming the pre-warn
zone. Additionally, if a full trigger zone is left open, the system will trigger a total of 3
times before bypassing the zone. Once the zone is closed again, it will re-arm that
zone.
Security System Features (cont’d)
Using The Valet Switch
EMERGENCY OVERRIDE
If you were to lose your controller or if the battery were to die while the sytem is
armed, you’d need to perform an emergency override to disarm the system and use
your vehicle. To perform an emergency override, use the following steps:
STEP 1 - Enter the vehicle (the alarm should sound)
STEP 2 - Turn the ignition key to the “ON” position
STEP 3 - Press the valet switch (located in the window-mount antenna) once
NOTE: Enter your SecureCode at this time if programmed via user feature #1
STEP 4 - Turn the ignition “OFF”.
You can now use the vehicle as normal. It is advised to place the system in valet
mode until you have a functioning controller once again.
VALET MODES
ALARM VALET MODE, while active, completely disables all security functions.
Keyless entry and remote start are still operable. To enter valet mode, perform the
following steps:
STEP 1 - Disarm the system either with the controller or by performing an emergency
override (make sure not to hold the brake pedal).
STEP 2 - Press and hold the valet switch (located in the window-mount antenna)
for 2 seconds. The system will chirp once and the RED status light will turn on. The
controller will reect on the status page that the system is in alarm valet mode.

12
Using The Valet Switch (cont’d)
REMOTE START VALET MODE, while active, disables remote start. Keyless entry
and alarm functions are still operable. To enter remote start valet mode, perform the
following steps:
STEP 1 - Disarm the system either with the controller or by performing an emergency
override and hold the brake pedal.
STEP 2 - Press and hold the valet switch (located in the window-mount antenna) for
2 seconds. The system will chirp once and the GREEN status light will turn on. The
controller will not reect remote start valet mode.
FULL VALET MODE combines both alarm & remote start valet modes. To acti-
vated full valet mode, follow these steps:
STEP 1 - Enter remote start valet. You will hear a chirp.
STEP 2 - Release the brake pedal but continue holding the valet switch. After 2 sec-
onds, you will hear a second chirp.
STEP 3 - Immediately release the valet switch. The status light will alternate between
RED and GREEN every second.
EXITING VALET MODES is as simple as just pressing and releasing the valet
switch once. The status light will turn off. This procedure is the same for all forms of
valet mode.
SECURECODE
SecureCode allows you to customize the number of valet presses required to per-
form an emergency override. This is an extra layer of security that prevents anyone
from overriding the alarm even if they have a key to the vehicle. SecureCode has 2
stages with the rst requiring 1-9 button valet presses and the second requiring 0-9
valet button presses. This gives you 99 possible combinations. To program a custom
SecureCode, please refer to user feature #1. To perform an emergency override with
SecureCode, use the following steps:
STEP 1 - With the system armed, enter the vehicle (the alarm will activate).
STEP 2 - Turn the ignition switch to the “ON” position.
STEP 3 - Within 5 seconds of step 2, press the valet switch to enter the rst digit of
your programmed code.
STEP 4 - After a few seconds, the siren will stop sounding and chirp once (conrming
stage 1). The siren will then continue sounding.
STEP 5 - Now, within 5 seconds of step 4, press the valet switch to enter the second
digit of your code. If the code is correct, the alarm will disarm.
If the code is entered incorrectly, you must turn the ignition key OFF, then back
ON to try again. Additionally, if 2 failed attempts are made, the alarm will ignore any
further attempts for 2 minutes.
The Status Light
The status lights, located in the window-mount antenna, provide a visual indication
of the system’s status via GREEN (remote start status) and RED (alarm status) lights.
SECURITY SYSTEM STATUS (RED LIGHT):
OFF: The alarm is disarmed and not performing any automatic functions.
ON CONSTANT: The alarm is in valet mode.
FLASHING SLOW: The alarm is armed and monitoring all entry points.
FLASHING FAST: One of the automatic arming features is in progress.

13
The Status Light (cont’d)
AUTOMATIC TRANSMITTER VERIFICATION (RED LIGHT):
Every time you turn on the ignition key, the status light will ash a number of times
equal to the number of controllers/transmitters programmed to the system. This
unique security feature protects you from a potential thief (valet attendant, mechanic,
installer, etc.) from adding their own transmitter without your knowledge and access-
ing your vehicle and it’s contents at a later time (the perfect crime!).
ZONE VIOLATION RECALL:
If the security system is triggered, upon disarming, the RED status lights will ash
a number of times to indicate exactly which zone(s), has been violated. It will store
the last 2 violated circuits and continually repeat the ash pattern until the system is
disarmed and the vehicle’s ignition key is turned ON.
2 FLASHES: Hood trigger
3 FLASHES: Door trigger
4 FLASHES: Sensor port trigger
REMOTE START STATUS (GREEN LIGHT):
OFF: The remote start is off and in standby mode.
ON CONSTANT: The remote start is in valet mode.
FLASHING SLOW: The engine was started successfully and is running.
FLASHING FAST: The remote start sequence has begun and is in process of starting
the vehicle’s engine.
REMOTE START DIAGNOSTICS (GREEN LIGHT):
The remote start system can also indicate which zone caused the last remote
start cycle was ended. To see this indicator, place the system into alarm valet mode.
Immediately after the chirp, the GREEN status light will ash to indicate what caused
remote start to end.
1 FLASH: Run time expired.
2 FLASHES: Brake pedal was pressed.
3 FLASHES: Engine stalled or a bad tach signal.
4 FLASHES: Received transmitter command to stop.
5 FLASHES: Gear selector was moved from park(or the parking brake was released).
6 FLASHES: The alarm was triggered or low battery voltage.
COMBINATION INDICATIONS:
Thes indication reect combinations of functions involving the security system AND
remote start.
SLOWLY ALTERNATES GREEN/RED: System is in full valet mode.
SOLID GREEN W/ RED FLASH: System is in remote start valet w/ the alarm armed.
SOLID RED W/ GREEN FLASH: System is in alarm valet w/ remote start activated.
FAST ALTERNATES GREEN/RED: Alarm armed w/ remote start activated.
SLOW FLASHING GREEN W/ 1-4 RED FLASHES: Zone violation recall during
remote start mode.
SLOW FLASHING RED W/ 1 GREEN FLASH: System is armed and ready to remote
start in manual transmission mode.

14
Multi-Car Operation & Vehicle Proles
MULTI-CAR OPERATION
The controller can operate up to 2 different systems. When controlling 2 systems, it
will receive all status updates on the currently selected vehicle prole and will receive
only trigger alerts for the 2nd vehicle. You can switch from one car to the other at any-
time as well as choose a unique image and name for each vehicle. Use the following
steps to change vehicle proles as well as select the vehicle image and name.
1) Access SCREEN 3: press the HOME button, tap the
screen, press the down arrow twice.
2) Press the “CAR1” icon (pictured to the left). You will then
see the “CAR 1 NAME” screen.
3) Program the name you desire (up to 16 characters)
BLUE arrow: Backspace
YELLOW arrow: Scrolls through numbers,
letters, and symbol screens
4) Press the GREEN arrow to save the name.
NOTE: Programming the name for CAR2 is the same
procedure, except you will need to press the CAR2 icon
in step 2.
PROGRAMMING THE VEHICLE NAME
SELECTING CAR1 OR CAR2
Once the vehicle names have been programmed for both vehicle proles, you can
simply switch between the two as needed. To do so:
1) Tap the desired vehicle’s icon (CAR1 or CAR2) on SCREEN 3 as if you are going
to change the name.
2) Then, press the GREEN arrow
icon to select that prole.
CAR 1 CAR 2
SELECTING THE VEHICLE IMAGE
You can select a different vehicle image for each vehicle prole if desired. The
controller is preloaded with 3 different vehicle images, a CAR, TRUCK, and SUV. To
change the image, follow these steps:
1) Make sure you are already in the desired vehicle prole
(CAR1 or CAR2).
2) Access SCREEN 3
3) Press the VEHICLE IMAGE icon (pictured to the right) to
view the image select screen.
4) Press the GREEN UP ARROW to change the image.
5) Press the FOLDER icon to save your selection.

15
CLOCK & TIME OPTIONS OVERVIEW
The controller’s clock has 3 programmable options. You can set the time & date,
select 12 or 24 hour format, and program the built-in alarm clock. To program these
options, you must rst access SCREEN 4 by pressing the home button, tapping the
screen, and pressing the DOWN ARROW 3 times.
SCREEN 4
Clock Format 12/24
Hour
Demo Mode
See pg. 17
Set Time/Date
Set Alarm Clock
1) Access SCREEN 4 and press the “SET TIME/DATE” icon.
2) Use the number pad screen to set the date. Format: MMDDYY
~ BLUE arrow = Backspace
3) Once the date is correct, press the GREEN arrow to save.
SETTING THE TIME & DATE
SELECTING BUTTON BEEP, MELODY, & VIBRATE MODES
The controller has 3 different type of alert modes. BUTTON BEEP congures the
controller to beep as a conrmation when you press any icon on the screen. The
MELODY and VIBRATE settings congure how you are alerted any time the controller
receives a conrmation or alert from the vehicle’s system. MELODY turns on/off all
audible alerts including voice alerts. VIBRATE mode turns on/off vibration alert. To
change these options:
1) Access SCREEN 3 (press HOME, tap the screen, press the DOWN ARROW twice)
2) Press the alert icon (pictured below).
3) Change the alert settings as desired according to the diagram below.
4) Press the folder icon to save the setting
Button Beep ON
Button Beep OFF
Vibrate ON/OFF
Melody ON/OFF
Save Settings
Vibrate ON Indicator
Melody ON Indicator
Alert Icon Alert Settings
2 3
Programming Controller Options

16
Programming Controller Options (cont’d)
SETTING THE TIME & DATE (cont’d)
4) Now, set the time using the +/- increment icons. You can increase or
decrease the minute or hour by increments of 5 or 1.
~Use the GREEN UP ARROW to change from hours to minutes.
5) Press the FOLDER icon to save the date & time.
SETTING THE TIME FORMAT (12 OR 24 HOUR)
1) Access SCREEN 4 (see page 15)
2) Press the TIME FORMAT icon (pictured on page 15) to toggle between 12 & 24
hour formats.
SETTING THE ALARM CLOCK
1) Access SCREEN 4 (see page 15)
2) Press the ALARM CLOCK icon (see page 15) to access the alarm clock screen.
3) Use the number pad screen to set the desired alarm time exactly in the same
method used to set the clock time.
4) Press the FOLDER icon to save the alarm clock setting.
Note: To turn the alarm clock off, set the alarm time to midnight
(12:00AM for 12HR format OR 0:00 for 24HR format)
DEMO MODE
Demo mode will show you a demonstration movie of all the controller’s available
functions along with conrmation animations and voice alerts. To view demo mode,
use the following steps.
1) Access SCREEN 4 (see page 15).
2) Press the DEMO icon (pictured on page 15).
LCD SCREEN DISPLAY OPTIONS OVERVIEW
The LCD screen has two adjustable parameters, SCREEN ON TIME and SCREEN
BRIGHTNESS. Both settings have an effect on battery life. So, it is recommended to
use the lowest settings your are comfortable with. These settings are accessed from
SCREEN 5. To access SCREEN 5, press the home button, tap the screen, and press
the DOWN ARROW 4 times.
SCREEN 5
Screen ON Time
Power Off
Screen Brightness
Trigger History

17
1) Access SCREEN 5 (see page 16)
2) Press the SCREEN ON TIME icon (see page 16)
3) Choose the 5, 10, or 15 second preset and, if desired, adjust with the +/- 1 second
increment icons.
4) Press the FOLDER icon to save the setting
SETTING THE SCREEN ON TIME
1) Access SCREEN 5 (see page 16)
2) Press the SCREEN BRIGHTNESS icon (see page 16)
3) Choose any of the 1-5 brightness settings to your liking.
4) Press the FOLDER icon to save the setting
SETTING THE SCREEN BRIGHTNESS
The controller will store recent alarm trigger events in a log that displays the date
& time of the trigger as well as which zone was triggered. The history is cleared when
you turn on the vehicle’s ignition. To view the trigger history:
1) Access SCREEN 5 (see page 16)
2) Press the TRIGGER HISTORY icon (see page 16)
3) Press the HOME button to exit.
VIEWING THE ALARM TRIGGER HISTORY
Programming Controller Options (cont’d)
Other Controller Functions
The controller can be turned off completely to save battery life while traveling or out
of range of the vehicle. To turn the controller off:
1) Access SCREEN 5 (see page 16)
2) Press the POWER OFF icon (see page 16)
3) You will see a warning screen asking you to conrm.
4) Press the FOLDER icon to conrm.
To turn the controller back on, press the HOME button.
POWER OFF MODE
The controller has 2 convenient timer functions. The PARKING TIMER tells you
how long you’ve been parked in case you are at a parking meter or other parking
areas with time restrictions. The REMOTE START TIMER tells you how long your
engine has been running in remote start mode. This is a good indicator to judge how
long you have left in the remote start run cycle.
PARKING TIMER: Press LOCK twice within 5 seconds. When the controller receives
both LOCK conrmations, it will start the timer.
REMOTE START TIMER: This turns on every time you remote start.
Note: Pressing the home screen during either timer mode will show the time
clock for 2 seconds before returning to the timer.
PARKING TIMER & REMOTE START TIMER

18
Anti-Carjacking Protection
The system is equipped with three separate Anti-Carjacking protection features
(ignition, open door, or by the transmitter). All three are programmable, and must be
turned on to operate. Once activated, the user has 53 seconds to cancel the Anti-
Carjacking protection process by pressing the Valet Switch once. If Anti-Carjacking is
not cancelled, 53 seconds after being activated the siren will begin to chirp for 7 sec-
onds to alert the user that the system is about to enter into an alarm condition. The
Valet Switch may still be pressed once during this period to cancel the Anti-Carjacking
process.
If the Anti-Carjacking process is not cancelled before the 60 second countdown
expires, the system will enter an alarm condition, sounding the siren and ashing the
parking lights. 30 seconds after this occurs, or should the ignition be turned off in the
meantime, the stater interrupt will engage. Once the system enters the alarm condi-
tion, it will not respond to the transmitter, nor will the system reset automatically after
60 seconds, and it can only be disengaged by:
Step 1 Turning the vehicle’s ignition off.
Step 2 Turning the ignition back on.
Step 3 Within 5 seconds, perform an Emergency Override using the Valet Switch. If
the SecureCode has been customized, the correct number of Valet Switch presses
must be made.
The three types of Anti-Carjacking protection features are:
Ignition Activated Anti-Carjacking activates every time the vehicle’s ignition is
turned on. The Valet Switch must be pressed within 60 seconds of activating to can-
cel Anti-Carjacking. This is User Programmable Feature #17.
Door Anti-Carjacking activates when a door is opened after the vehicle is started
and the engine is running. The Valet Switch must be pressed within 60 seconds after
activation to cancel Anti-Carjacking. This is User Programmable Feature #18.
Transmitter Anti-Carjacking is activated by pressing and holding the “CH3” icon
(1-way transmitter: “trunk & “start”) for 3 seconds, while the vehicle’s ignition is on.
The Valet Switch must be pressed within 60 seconds after this is done to cancel Anti-
Carjacking. This is User Programmable Feature #19.

19
Programming Controllers/Transmitters
Step 1 Have all transmitters which are to operate the system at hand. Then, turn the
ignition “on”.
If the Unauthorized Transmitter Alert feature is on, programming a transmitter to the
system will activate the “UTA” warning and the extended Status Light indication. For
the next 48 hours, the siren/horn will sound a brief series of chirps every time the
vehicle’s ignition key is turned on.
Step 3 Press the “lock” button on each remaining transmitter one at a time. The sys-
tem will chirp the siren/horn once to conrm that each was learned. The transmitter’s
other three button’s functions will automatically be assigned when the “lock” button is
learned. If a code is not received within a 10 second period, the learning processwill
automatically terminate, as indicated by another siren/horn burst.
Step 2 Within 5 seconds of turning on the ignition, press the Valet Switch 5 times.
The siren/horn will briey sound, conrming that for the next 10 seconds the system
is ready to learn a transmitter/controller code. To enter a code, simply press and
release the “lock” button. When the rst code is learned all existing stored codes will
be erased.
Special Programming procedure to turn On the UTA feature: Using this method
to program transmitters or optional controllers, and to turn on the Unauthorized Trans-
mitter Alert feature.
Follow the same steps as the Standard Programming, but on any transmitter/con-
troller being programmed instead of pressing the “lock” button, press the “lock” and
the “unlock” buttons together. This action turns on the Unauthorized Transmitter
Alert feature and at the same time programs the transmitter or controller to operate
the system.
Standard Programming: Using this method to program additional or replacement
transmitters does not turn on or otherwise affect the Unauthorized Transmitter Alert
(UTA) feature.
Once the Unauthorized Transmitter Alert feature is turned on, the warning will
sound for 48 hours after any transmitter programming, including the programming
session which was used to turn it on. This feature can only be turned off again by
sending the system back to Omega for a reset.
Step 1 Turn the ignition key “ON”, then “OFF”
Step 2 Within 5 seconds of step 1, press the valet switch 5 times to access user
features (10 times to access installer features).
~ The siren/horn will sound and the status light will turn on.
Step 3 Within 10 seconds of step 2, press the valet switch the number of times cor-
responding with the desired feature’s number.
~ The siren/horn will chirp, the status lights, and the parking lights will ash equal
to the selected feature.
Step 4 Change the feature by pressing the transmitter button that corresponds with
the desired setting. The siren/horn will chirp to correspond with the chosen setting.
Programming Features

20
User Programmable Features
To custom program a new SecureCode:
Step 1 Follow Steps 1 to 4 in the previous “Programming Features” section to access
“feature #1”.
Step 2 Within 10 seconds slowly press and release the controller or transmitter’s
“arm/lock” button the number of times equal to the desired SecureCode for stage 1,
allow the system to respond to each controller/transmitter button press with a siren
chirp before pressing the button again. A few seconds after the nal button press, the
system will chirp the horn/siren conrming the total number for stage 1.
Step 3 Congure stage 2 of the SecureCode by pressing and releasing the “disarm/
unlock” button the number of times desired for the stage 2. The system will conrm
as it did for stage 1.
Feature #2 - Last Door Arming
Off (press “arm/lock” button to program) - DEFAULT
On w/o doors locking (press “disarm/unlock” button to program)
On w/ doors locking (press “trunk” button to program)
“Last Door Arming” has the system automatically arm itself every time you exit the
vehicle (the complete operation is described on pages 8 & 9). This feature turns
that operation on or off, and with options of having Last Door Arming operate with or
without also locking the doors when the system does arm.
Feature #1 - SecureCode
DEFAULT - 1 Press
SecureCode is a unique patented feature which allows you to custom select the num-
ber of Valet Switch presses in two stages, instead of a single “1 press”, which would
be required in order to perform an Emergency Override. If any of the three anti-car-
jacking features are utilized, a customized SecureCode would also be required to turn
it off once it is fully activated. The SecureCode operation is described on page 12.
Feature #3 - Automatic Rearming
Off (press “arm/lock” button to program) - DEFAULT
On w/o doors locking (press “disarm/unlock” button to program)
On w/ doors locking (press “trunk” button to program)
“Automatic Rearming”, described on page 11, prevents the system from becoming
accidentally disarmed by having it arm itself after being disarmed, if a door is not then
opened or the ignition turned on. Options are to have Automatic Rearming operate
with or without also locking the doors when the system does rearm.
Feature #4 - Starter Interrupt Functions
Alarm Only (press “arm/lock” button to program) - DEFAULT
Off (press “disarm/unlock” button to program)
Automatic (press “trunk” button to program)
Alarm & Anti-Grind (press “start” button to program)
Alarm Only - The Starter Interrupt is operable whenever the alarm is armed.
Automatic - This will cause the Starter Interrupt output to automatically engage 90
seconds after the ignition switch is turned “off”, and after disarming the system.
Off - Completely eliminates the Starter Interrupt output,
Alarm & Anti-Grind - This setting engages starter interrupt when the alarm is armed
AND when the system is in remote start mode. This prevents the starter from grinding
if the user accidentally turns the key to “START” during remote start.