One Stop Gardens 91993 User manual

CAST IRONTRELLIS
WITHTULIP DESIGN
ASSEMBLY INSTRUCTIONS
3491 Mission Oaks Blvd., Camarillo, CA 93011
Visit ourWeb site at http://www.harborfreight.com
Copyright © 2004 by Harbor Freight Tools®.All rights reserved. No portion of this
manual or any artwork contained herein may be reproduced in any shape or form
without the express written consent of Harbor FreightTools.
For technical questions and replacement parts, please call 1-800-444-3353
®
91993

SKU 91993 For technical questions, please call 1-800-444-3353. Page 2
Specifications
Save This Manual
You will need the manual for the safety warnings and precautions, assembly
instructions, operating and maintenance procedures, parts list and diagram. Keep
your invoice with this manual. Write the invoice number on the inside of the front
cover. Keep the manual and invoice in a safe and dry place for future reference.
Safety Warnings and Precautions
WARNING:When using this product, basic safety precautions should always
be followed to reduce the risk of personal injury and damage to equipment.
Read all instructions before using this product!
1. Keep work area clean. Cluttered areas invite injuries.
2. Use eye and ear protection. Always wear ANSI approved impact safety
goggles when assembling this product. Goggles are available from Harbor
Freight Tools.
3. Stay alert.Watch what you are doing, use common sense.Do not assemble
this product when you are tired.Two or more people are required for
assembly.
4. Check for damaged parts. Before using this product, any part that appears
damaged should be carefully checked to determine that it will operate
properly and perform its intended function. Check for loose parts and any
other condition that may affect the operation of this product. Replace loose
or worn parts immediately. Any part that is damaged should be properly
repaired or replaced.
5. Replacement parts. When servicing, use only identical replacement parts.
Use of any other parts will void the warranty.
6. Always placeTrellis on even ground. Locate Trellis in a spot that is flat
and level without an uneven surface, away from electrical wires.Uneven
ground could cause tipping. Never lean on or lean against the Trellis.
Permanently secure the Trellis to a solid surface to prevent tipping.
7. Do not allow children to climb on the sides of this product or swing on
the gate. Always supervise children when playing around this product.
Overall Dimensions
Gate Dimensions
Materials
Overall Weight
82-1/2”Tall X 62-3/4” Wide X 19-3/4” Deep
41-1/2” High X 22-1/2” Wide X 3/4” (2X) Sides
Heavy Duty Cast Iron w/Copper and Black Brushed Details
130 Lbs.

SKU 91993 For technical questions, please call 1-800-444-3353. Page 3
Warning:The warnings, cautions, and instructions discussed in this instruction
manual cannot cover all possible conditions and situations that may occur. It
must be understood by the operator that common sense and caution are
factors which cannot be built into this product, but must be supplied by the
operator.
Unpacking
When unpacking, check to make sure the following parts are included. If any parts
are missing or broken, please call Harbor Freight Tools at the number on the cover of
this manual.
Assembly Instructions
1. Place parts on a smooth surface to avoid scratching. On the Frame (G) piece,
identify the top by the two predrilled holes in the steel tubing. Match the holes in
the Frame (G) with holes in the shorter side of the Corner Bracket (I). Slip the
Bolt (F) with Washer (D) through outside of the Frame (G). Anchor on the other
side of the Frame with a Washer (D) and Nut (C). Finger tighten. Repeat
attaching Corner Brackets to the Frame steel tubing, three other places.
See Figures 1 & 2.
2. Stand the two Frame (G) end pieces opposite each other. Be sure the brackets
on the Frame, for the Gate (A), are opposite each other. See Page 4. Lift one
Top Support Beam (H), (curve down), up over the Frame (G). Slip Bolt (F) with
Washer (D) through outside of the Top Support Beam (H) and through the holes
in the Corner Bracket (I). Anchor on the other side with a Washer (D) and Nut
(C). Repeat attaching Top Support Beam on the other end. Attach the opposite
Top Support Beam, forming an arch or trellis. Finger tighten all hardware at this
time. See Figures 1- 3.
Figure 3
Corner Bracket (I)
Figure 1
Top
Support
Beam (H)
Figure 2
Washer (D)
Nut (C)
Cap (B)
Bolt (F)
Washer (D)
Frame (G)
Corner Bracket (I)
Corner
Bracket (I)

SKU 91993 For technical questions, please call 1-800-444-3353. Page 4
3. Stand the Trellis in the area you have chosen, being mindful of the terrain.It
must be level and flat.If mounting in soil, be sure the ground is not too moist
and avoid areas that have water drainage. (If you choose to mount the Trellis on
cement or a wooden deck, seek the advise of a professional.
4. Mount the Gate (A) into the brackets on the Frame (G).Be sure the Gate will
close and lock properly. If not, readjust how the Frame (G) is placed. Be sure
the Gate swings freely and is lined-up evenly when locked. See Figures 6 & 7.
5. Once you are sure the Trellis is in the correct position and level, tighten all
hardware and put Caps (B) over the Nuts. Hammer the Stakes (E) through the
holes in the brackets at the foot of the Frames (G) (eight places). Be sure you
are hammering into SOLID ground if mounting in a grassy area. Make sure
that there are no electrical cables or wires in the path of the Stakes (E). See
Figures 7 & 8.
6. Check theTrellis often to make sure it is mounted solidly. Harbor Freight Tools
is not responsible for accidents that may occur due to improper installation of
the Cast Iron Trellis.
Figure 6
Figure 7
Figure 8
Stake (E)
Foot of
Frame (G)
Lock
Gate (A)
Gate (A)
Bracket on
Frame (G)
Hooks
into
Brackets
Stake(E)

SKU 91993 For technical questions, please call 1-800-444-3353. Page 5
Parts List
Part # Description Qty.
Assembly Drawing
NOTE: Some parts are listed and shown for illustration purposes only and are not available individually as replacement parts.
2
21
21
42
8
21
2
2
4
Gate
Cap
Nut M6
Washer 6
Stake
Bolt M6 X 55
Frame
Top Support Beam
Corner Bracket
Part B
Part A
Part G
Part E
A
B
C
D
E
F
G
H
I
Part C
Part D
Part F
Part D
Foot of Frame
Part I
Part H
Brackets for Gate
PLEASE READ THE FOLLOWING CAREFULLY
THEMANUFACTURER AND/OR DISTRIBUTORHASPROVIDEDTHEPARTS DIAGRAMINTHIS MANUAL
AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER NOR DISTRIBUTOR MAKES ANY
REPRESENTATION OR WARRANTY OF ANY KINDTOTHE BUYER THAT HE OR SHE IS QUALIFIEDTO
MAKE ANY REPAIRS TO THE PRODUCT OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY
PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY
STATES THat ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED
AND LICENSED TECHNICIANS AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISK AND
LIABILITY ARISING OUT OF HIS OR HER REPAIRSTOTHE ORIGINAL PRODUCT OR REPLACEMENT
PARTS THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS
THERETO.