One Stop Gardens 04249 User manual

ASSEMBLY INSTRUCTIONS
3491 Mission Oaks Blvd., Camarillo, CA 93011
Visit our Web site at http://www.harborfreight.com
Copyright © 2003 by Harbor Freight Tools®. All rights reserved. No portion of this manual
or any artwork contained herein may be reproduced in any shape or form without the
express written consent of Harbor Freight Tools.
For technical questions please call 1-800-444-3353
MINI GARDEN BISTRO
FURNITURE SET
4 PIECE SET
®

SKU 04249 PAGE 2
SPECIFICATIONS
SAVE THIS MANUAL
You will need the manual for the safety warnings and precautions, assembly
instructions, operating and maintenance procedures, parts list and diagram. Keep
your invoice with this manual. Write the invoice number on the inside of the front
cover. Keep the manual and invoice in a safe and dry place for future reference.
SAFETY WARNINGS AND PRECAUTIONS
1. KEEP PRODUCT USAGE AREA CLEAN. Cluttered areas invite injuries. Place
product on flat, level surface such as carpet or grass. Concrete could hurt child if
chairs or bench is tipped over.
2. KEEP CHILDREN AWAY FROM PRODUCT DURING ASSEMBLY. Do not allow
children to use until all hardware in this product is fully assembled and tightened.
3. DO NOT ATTEMPT TO ASSEMBLE THIS PRODUCT IF UNDER THE INFLU-
ENCE OF ALCOHOL OR DRUGS. Read warning labels on prescriptions to
determine if your judgement or reflexes are impaired while taking drugs. If there is
any doubt, do not attempt to assemble this product.
4. USE EYE PROTECTION. Wear ANSI approved safety impact goggles when
assembling this product. Goggles are available from Harbor Freight Tools.
5. PERIODICALLY CHECK. Check Bolts and Nuts periodically to be sure hardware
has not loosened.
6. STAY ALERT. Watch what you are doing at all times. Use common sense. Do not
assemble this product when you are tired or distracted from the job at hand.
7. CHECK FOR DAMAGED PARTS. Before using this product, carefully check that it
will operate properly and perform its intended function. Check for damaged parts
and any other conditions that may affect its operation. Replace or repair damaged
or worn parts immediately.
Cast Aluminum
White Glossy Enamel
Flower Design
22-1/2"L X 13"W X 22-3/8"H
11-1/4"L X 10-1/2"W X 21-1/4"H
18-3/4"Dia. X 16-1/2"H
Construction
Finish
Design
Bench Dimensions
Chair Dimensions
Table Dimensions
Item Discription

8. REPLACEMENT PARTS AND ACCESSORIES. When servicing, use only identical
replacement parts. Only use accessories intended for use with this product.
Approved accessories are available from Harbor Freight Tools.
9. THIS PRODUCT IS MANUFACTURED OF CAST ALUMINIUM PARTS AND IS BRITTLE.
Do not force any part of the assembly and do not overtighten the bolts. Serious damage
can occur. Do not stand on Chair, Bench, or Table. Use only for intended purpose.
Chairs are not made for adults. Injury could occur if Chair is overloaded. Use caution!
10. RECOMMENDED AGE APPROPRIATE USE is 4–7 year old children. Weight range, 30
to 70 lbs. on Chairs. Maximum weight for Bench is 100 lbs.
UNPACKING
When unpacking, check to make sure all parts shown on the Parts List (page 5) are
included. If any parts are missing or broken, please call Harbor Freight Tools at the
number shown on the cover of this manual as soon as possible.
ASSEMBLY INSTRUCTIONS
We suggest you assemble the unit on a soft surface to avoid damage to the finish.
SKU 04249 PAGE 3
1. Position the Back Rest (#A1) by inserting the cast aluminum pegs into the holes in the
Bench Seat (#C1). Attach the Bench Seat (#C1) to Back Rest (#A1) using Screw (#1),
Washer (#2), and Nut (#3). See Figure 1, Figure 2 and 3.
2. Attach the Legs (#D1) in eight places using Bolts (#4), Washer (#2), and Nut (#3).
See Figure 1 and 2.
3. Attach Bench Arm Rests (#B1) to Back Rest (#A1) and Seat (#C1) using Screws (#1),
Washers (#2), and Nuts (#3). Use the white Screws, Washers, and Nuts on the back of
the Back Rest (#A1) where they are visible. Shown in Figure 3.
ASSEMBLY OF BENCH
#C1
Seat
#4, #2, #3 #1, #2, #3
(white)
#1, #2,
#3
#A1
Back Rest
#B1
Arm Rest
#A1
Back Rest
Figure 2 Figure 3
#D1
Leg
#4, #2,
#3
(View from underneathbench)
#1, #2,
#3
#C1
Seat
Figure 1
#C1
Seat

SKU 04249 PAGE 4
1. Place the Legs (#C3) in four places on the Seat (#B3) using Screws (#1), Washer (#2) and
Nuts (#3). See Figure 4.
CHAIR ASSEMBLY
Figure 4
2. Attach Back Rest (#A3) in two places on the Seat (#B3) using Screws (#1), Washer (#2)
and Nuts (#3). See Figure 5.
Figure 5
#1, #2, #3
#1, #2, #3
#C3
#B3
#A3
1. Place the Legs (#B2) in four places on the Table Top (#A2) using Bolts (#1a), Washer (#2)
and Nuts (#3). See Figure 6.
TABLE ASSEMBLY
2. When assembly is completed on the Chairs, Bench, and Table, place black PVC
Stoppers (#5) on all Legs. Tap on tightly. See Figure 7.
Figure 7
#1a, #2, #3
#1a, #2, #3
Figure 6
#5
#5
#B2
#A2
#B3

PARTS LIST
SKU 04249 PAGE 5
ASSEMBLY ILLUSTRATION
A1
Back Rest
Arm Rest
Seat
Leg
Screw (6X25MM)
Washer
Nut
Bolt (6X25MM)
PVC Stoppers
PART # DESCRIPTION QTY
A1
B1
C1
D1
1
2
3
4
5
1
2
1
4
2
14
14
8
16
Table Top
Leg
Bolt (6X30MM)
Washer
Nut
PART # DESCRIPTION QTY
A2
B2
1a
2
3
1
3
6
6
6
Back Rest
Seat
Leg
Screw (6X25MM)
Washer
Nut
PART # DESCRIPTION QTY
A3
B3
C3
1
2
3
2
2
8
8
12
12
DRAWING OF BENCH
DRAWING OF TABLE
DRAWING OF CHAIR
MAINTENANCE
1. For better and safer performance, keep all parts of this product clean and dry at
all times.
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS DIAGRAM IN THIS
MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER NOR DISTRIBUTOR
MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS
QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT OR THAT HE OR SHE IS QUALIFIED TO
REPLACE ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR
EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN
BY CERTIFIED AND LICENSED TECHNICIANS AND NOT BY THE BUYER. THE BUYER ASSUMES
ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR
REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACE-
MENT PARTS THERETO.
A3
B3
C3
1
2
3
1
2
3
1a
2
3
A2
B2
B1
C1
D1
4
2
3
DRAWING OF CHAIR DRAWING OF TABLE DRAWING OF BENCH
5
5
5