One Stop Gardens 91000 User manual

3 Position Leisure Chair3 Position Leisure Chair
3 Position Leisure Chair3 Position Leisure Chair
3 Position Leisure Chair
ASSEMBLY AND OPERATING INSTRUCTIONS
3491 Mission Oaks Blvd., Camarillo, CA 93011
Visit ourWeb site at http://www.harborfreight.com
Copyright©2003byHarborFreightTools®. Allrights reserved.Noportion
of this manual or any artwork contained herein may be reproduced in any
shapeorformwithout the expresswrittenconsentofHarbor FreightTools.
For technical questions and replacement parts, please call 1-800-444-3353
91000

SKU91000 Page 2
Specifications
SaveThis Manual
You willneedthemanualforthesafety warningsandprecautions, assembly
instructions, operating and maintenance procedures, parts list and diagram. Keep
your invoice with this manual. Write the invoice number on the inside of the front
cover. Keep the manual and invoice in a safe and dry place for future reference.
SafetyWarnings and Precautions
WARNING:Whenusingchair,basicsafetyprecautionsshouldalwaysbefollowed
to reduce the risk of personal injury and damage to equipment.
Read all instructions before using this chair!
1. Keep your area clean. Clutteredareasinvite injuries.
2. Observe proper use. Don’t expose to rain, excess heat or abusive treatment.
When getting into this chair, please do so gradually.Never jump into or bounce
on this chair.
3. Store idle equipment. Whennotin use,chairshould bestoredin adrylocation
out of direct sunlight to preserve its good condition.
4. Use the right chair for the job.Do not attempt to force a small chair to do the
work of a larger or differently designed chair.There are certain applications for
which this chair was designed. It will do the job better and more safely when
usedasintended.Donot modifythischairanddonotuse thischairforapurpose
for which it was not intended.
METINOITPIRCSED
snoisnemiD )neponehwelbairav( -93 1/4-42xW"42xH" 3/8)desolC(L"
-73~ 1/4)nepO(L"03~xW"42xH"
noitcurtsnoC -1 1/8gnibutleetsretemaid" tniapetihwssolghgiH
eziSnoihsuC-24 5/8-22x" 3/8"
slairetaMnoihsuC revocnottoC%001 gnillifretseyloP%001
thgieWteN.sbL01.21
yticapaCthgieW.sbL052

SKU91000 Page 3
5. Dress properly. Do not wearloose clothing orjewelry astheycanbe caught in
movingparts. Wear restrictivehaircoveringto contain longhairwhen unfolding
orrefolding the chair.
6. Do not overreach. Keep proper footing and balance at all times.Do not reach
over or across this chair. Do not stand on this chair.
7. Maintain chair with care. Inspect chair periodically and, if damaged, have it
repairedby anauthorizedtechnician.
8. Checkfordamagedparts. Beforeusingthechair,anypartthatappearsdamaged
shouldbecarefully checkedtodeterminethatitwilloperateproperly andperform
its intended function. Check for alignment and binding of moving parts; any
brokenpartsor mountingfixtures;andanyotherconditionthatmayaffectproper
operation.Anypartthatis damaged should be properly repaired or replaced by
aqualified technician.
9. Replacement parts and accessories. When servicing, use only identical
replacement parts. Use of any other parts will void the warranty. Only use
accessoriesintendedforuse withthischair.Approved accessoriesareavailable
fromHarbor FreightTools.
10. When folding or unfolding the chair: takecare thatyourfingersor otherparts
of your body or clothing do not become entangled in the chair.
11. Do not exceed the weight capacity of this chair.Thischairisratedfor250lbs.
Donotoverload the chair. Do notleanbackwardonthe chair. Donotusetop of
chair as a support;chair can easily tip over.
12. Don’t allow children to play on or around this chair. Exercise control over
theenvironmentinwhichthis chairisused.Donotallowchildren orotherlimited-
responsibilitypeople to play, run, jump onoraroundthis chair.Serious personal
or property damage may result.
13. Maintenance. When not in use, store the chair in a dry place, out of direct
sunlight.Occasionallycleanthe fabric with a vacuumorbrush.Ifnecessary, the
fabric cover can be washed. Allow to air dry to prevent shrinkage. If the paint is
scratched; sand to remove any accumulated rust and smooth the surface and
thenapplya rust-inhibiting paint.
Warning:The warnings,cautions,and instructionsdiscussed in
this instruction manual cannot cover all possible
conditions and situations that may occur. It must be
understood by the operator that common sense and
caution are factors which cannot be built into this
product,but must be supplied by the operator.

SKU91000 Page 4
Assembly
1. Inserttherectangularbuckleofeach
Belt(4) intooneof the threeholesin
the Back Rest (3) as shown in the
photo.NOTE:Yourchoice ofholewill
determine the angle of the chair
back.The topmost hole will provide
themost uprightposition,the lowest
holeprovides themost relaxedback
position.NOTE:Besurethehook on
theotherend of each belt ispointed
downward,forassemblyintotheArm
Rest(1).
2 . Insert the Back Rest (3) into the Leg
(2) as shown in Fig. 2. Be sure the Belts
(4)are facingforward.
3. Insert the End Caps (5) into the
openendsofthetubeswhichmake
the Arm Rest (1).Place the Fabric
Cover (7) into position, by sliding
the pocket sewn into the upper
portion over the top of the Back
Rest (3), and the pockets sewn in
the lower portion over the
protrudingendsoftheArmRest(1).
Insert the triangular buckle of the
Belts(4)into theholesdrilledinthe
top of the Arm Rest (1) as shown
in Fig.3.

SKU91000 Page 5
Unpacking
When unpacking, check to make sure the following parts are included.
(1) Arm Rest (2) EndCaps
(1)Leg (4)Shoes
(1) Back Rest (1)Fabric Cover
(2) Belts
Note: The Arm Rest and Leg are pre-assembled as one unit.
The Shoes are also pre-assembled onto the Arm Rest and Leg unit.
Please refer to the Assembly Drawing on page 6 for illustration of these parts.
If any parts are missing or broken, please call Harbor FreightTools at the number
on the cover of this manual.
Parts List
#traPnoitpircseDytitnauQ
1tseRmrA1
2geL1
3tseRkcaB1
4tleB2
5paCdnE2
6eohS4
7revoCcirbaF1
PLEASE READTHE FOLLOWING CAREFULLY
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS
DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE
MANUFACTURER NOR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY
OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS
TO THE PRODUCT OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF
THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY
STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN
BY CERTIFIED AND LICENSED TECHNICIANS AND NOT BY THE BUYER. THE BUYER
ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE
ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS
OR HER INSTALLATION OF REPLACEMENT PARTS THERETO.

SKU91000 Page 6
NOTE: Some parts are listed and shown for illustration purposes
onlyand arenot available individuallyas replacementparts.
Assembly Drawing