Oneida Air Systems AHR000025 User manual

Appearance may vary slightly
oneida-air.com1-800-732-4065
Rev: B 20230504LL Doc. #ZBI000054
Hose Reel
Wall Mount
Supercell Mount
#AHR000025
# AHK041425
INSTRUCTION SHEET
Patents: www.oneida-air.com/patents

2Oneida Air Systems
System Contents
ID Part number Part description Qty
A* AHP000005 Body Assembly 1
A1* AAC810025 Core 1
A2* AHM000025 Wall Mount Plate 1
A3* AHS000025 Handle Side Assembly 1
A4* AHS000251 Outlet & Brake Side Assembly 1
B AHH500513 Handle 1
CAFW000007 2" Nylon Spacer 1
DAFS000009 1/4"-20 X 3" Button Head Screw 1
EDFH000025 2.5" Outlet Coupler 1
FAFS000011 8-32 x 3/8”Button Head Screw 3
ID Part number Part description Qty
G ACT000238 Brake 1
G1 AFT000011 1/4"-20 Hex Nut 2
HAFW000008 2" Nylon Spacer 1
IAFS000010 1/4"-20 X 3" Button Head Screw 1
FAFS000011 8-32 x 3/8" Button Head Screw 4
J ACL000003 3" Loop Clamp 1
KAFS000004 #10 x 1/2'' Self-Drilling Screw 1
LVSHRFB250 2.50" X 25' Hose 1
MACB360000 Turn Key Hose Clamp 2
NZBT000003 Template 1
You will need the following tools:
WALL MOUNTING BRACKET
Stud Finder Light Adhesive Tape Allen Wrench Power Drill
Tack / Center Punch / Nail Tape Measure / Ruler Flathead Screwdriver Drill Bit (for your wall fastener)
Wall Mounting Fasteners * Level Tool Pencil / Marker
*You will need to supply your own wall mounting hardware. Use appropriate fasteners for the wall type you are
installing your system onto (e.g. lag bolts, drywall anchors, etc.). Maximum Fastener Diameter: 3/8". Maximum
Washer Outside Diameter: 5/8".
*Extra components are included with the brake that are not needed for install.
If you cannot find an item on the list examine the packaging materials very
carefully. *Certain components are pre-installed for ease of installation.


3oneida-air.com
G
E F
F
H
J K
B
DC
L
N
I
M
A
G1
A3
A4
A1
A2
System Contents (Continued)
The Hose Reel should be mounted to a sturdy, reinforcedwall (e.g.
concrete wall, brick wall, wood-framed wall, etc.)Wall anchors can
be used if mounting on drywall. This template indicates the proper
drill holes and the full, assembled size of the Hose Reel.
Hose Reel Template
8-1/2"
216mm
16"
406 mm
8"
203 mm
8"
203 mm
Hose Reel Template
#ZBT000003
Drill Here Drill Here
Drill Here
Drill Here
Drill Here
Drill Here
LEVEL THIS LINELEVEL THIS LINE
The Hose Reel can be mounted so that the Handle is on either side
as the keyholes are bi-directional. This does not requirerotating the
templlate. Decide how you want yourHose Reel oriented during
installation to best meet your shop’sneeds.
Hose Reel Mounting Positions
Rev: C 20230504LL

4Oneida Air Systems
Assembly Instructions
1 read the 1/4"-20 X 3" Screw (D) through the
Spacer (H), Brake (G) and both 1/4"-20 Hex
Nuts (G1) as shown in [FIG. 1].
2 Secure the Brake Assembly (G) to the Outlet
& Brake Side Assembly (A4) using four 8-32 x
3/8" Screw (F) as shown in [FIG. 2].
3 Secure the Outlet Coupler (E) to the Outlet &
Brake Side Assembly (A4) using three 8-32 x
3/8" Screws (F) as shown in [FIG. 3].
D H
G
G
F
A4
G1
C
A4
F
FIG. 2
FIG. 3
FIG. 1

5oneida-air.com
FIG. 4
FIG. 5
4 read the Screw (D) through the Handle Side
Assembly (A3), Spacer (C) and Handle (B)
[FIG. 4].
Assembly Instructions (Continued)
B C H
A3
5 Identify where you will install the Hose Reel
in your shop and how the hose reel will be
oriented [FIG. 5].
Handle on
the left
Handle on
the right
Front View Front View

6Oneida Air Systems
Assembly Instructions
THE WALL BRACKET SHOULD BE MOUNTED TO A STURDY, REINFORCED WALL E.G. CONCRETE WALL,
WOODFRAMED WALL, ETC. WALL ANCHORS CAN BE USED IF MOUNTING ON DRYWALL. THE INCLUDED
TEMPLATE INDICATES THE PROPER DRILL HOLES AND THE FULL, ASSEMBLED SIZE OF THE WALL
BRACKET.
Wall
Hose
Reel
6 Mark a straight level line. Align the top of
the Template (N) with the marked line and
temporarily secure the template to the wall
with a tack or non-marking tape [FIG. 6a].
Place a mark through the template's paper at
each indicated crosshair (four bi-directional
keyway holes), then remove the template from
the wall [FIG. 6b].
Note: DO NOT FLIP THE TEMPLATE! e
dimensions of the template are accurate to
either orientation of the Hose Reel.
e central keyway holes can be used to further
secure the bracket if standard 16" on-center stud
spacing is not available.
TheHoseReel should be mounted to a sturdy, reinforced wall (e.g.
concretewall,brick wall, wood-framed wall, etc.) Wall anchors can
beusedif mounting on drywall. This template indicates the proper
drillholesand the full, assembled size of the Hose Reel.
Hose Reel Template
8-1/2"
216mm
16"
406mm
8"
203mm
8"
203mm
HoseReelTemplate
#ZBT000003
DrillHere DrillHere
DrillHere
DrillHere
DrillHere
DrillHere
LEVELTHIS LINELEVELTHIS LINE
TheHoseReel can be mounted so that the Handle is on either side
asthekeyholes are bi-directional. This does not require rotating the
templlate.Decidehow you want your Hose Reel oriented during
installationtobest meet your shop’s needs.
Hose Reel Mounting Positions
Rev:C20230504LL
FIG. 6a
FIG. 7
Mark
Here
FIG. 6b
7 Using appropriate fasteners for the wall type
you are installing your system onto, drill into
and install fasteners into the wall at all marked
locations.
a. Maximum Fastener Size: 3/8" diameter
b. Maximum Washer Size: 5/8" outside
diameter
Place washers onto each fastener and thread
the fasteners into all four holes, leaving at least
1/2" outside of the hole to t the Hose Reel
Assembly [FIG. 7].

7oneida-air.com
FIG. 8a FIG. 8b
Assembly Instructions (Continued)
8 Li the Hose Reel Assembly up and over the
fasteners so that the washer is on the inside of
the Hose Reel [FIG 8a].
Slide the Hose Reel Assembly down so that the
fastener is snugly inside the smaller section of
each keyhole [FIG 8b].
Wall
9 Tighten these four fasteners to secure the Hose
Reel Assembly to the wall [FIG. 9].
Note: If installing over drywall, avoid
overtightening as it may damage the wall.
10 Secure the Turn Key Hose Clamp (M) tightly
onto one end of the Hose (L) as shown in
[FIG. 10].
FIG. 10
FIG. 9

Assembly Instructions
8Oneida Air Systems
FIG. 11b
FIG. 11a
Assembly Instructions (Continued)
11 Partially tighten the Turn Key Hose Clamp
(M) onto the Outlet Coupler (E) as shown in
[FIG. 11a].
Feed the clamped end of the Hose (L) through
the access hole in the Core (A1) closest to the
Handle Side Assembly (A3) [FIG. 11b].
en attach the Hose to the Outlet Coupler.
You can guide the Hose by using the
secondary access hole in the Core closest to
the Outlet & Brake Side Assembly (A4). Secure
in place by rmly tightening the Turn Key
Hose Clamp on the Outlet Coupler [FIG 11c].
Note: To permanently install the Hose, silicone
can be applied to the Hose's cu prior to being
inserted into the Outlet Coupler.
FIG. 11c
Interior
View
Interior
View

9oneida-air.com
13 Guide the Hose (L) as you wind it around the
Core (A1) of the Body Assembly (A) so it is
neatly wrapped as shown in [FIG. 13].
Assembly Instructions (Continued)
12 Secure the Hose (L) to the Handle Side
Assembly (A3) with the Self-Drilling Screw
(K) and 3" Loop Clamp (J) as shown in [FIG
12].
Note: DO NOT screw into recessed portions of
the Core (A1).
FIG.12
FIG. 13

Customer Service Dept.
1-866-387-8822 • [e-mail]
1001 West Fayette Street, Syracuse, NY 13204 U.S.A.
Copyright © 2023 Oneida Air Systems, Inc.
ank you for your business!
Regardless of where you purchased your system, if you have any
questions or issues with missing / damaged parts, please call
Oneida Air Systems rst to let us help resolve your problem.
We fully stand behind the quality of our product and place the
utmost value on our customer’s satisfaction.
We want to do everything possible to make your purchase and
experience with Oneida Air Systems a good one!