Onicon D-100 User manual

D-100 FLOW DISPLAY
Siemens P1-FLN Network Interface Installation Guide
11451 Belcher Road South, Largo, FL 33773 • USA • Tel [phone] • Fax [phone]
www.onicon.com • [email protected] 03-18
0660-5 / 18343
Siemens P1-FLN

11451 Belcher Road South, Largo, FL 33773 • USA • Tel [phone] • Fax [phone] • [email protected]
D-100-P1 Flow Display Manual 03/18 - 0660-5 / 18343 Page 2

11451 Belcher Road South, Largo, FL 33773 • USA • Tel [phone] • Fax [phone] • [email protected]
D-100-P1 Flow Display Manual 03/18 - 0660-5 / 18343 Page 3
TABLE OF CONTENTS
1.0 INTRODUCTION ..................................................................................................5
1.1 PURPOSE OF THIS GUIDE .......................................................................5
1.2 TYPICAL D-100 NETWORK INTERFACE MODULE ...............................5
1.3 SPECIFICATIONS ......................................................................................5
1.4 NETWORK SIGNAL CONNECTIONS.......................................................6
1.4.1 Standard Network Interface ........................................................6
1.4.2 Optional Network Interface with
Isolated Digital Pulse Input (Di3)................................................7
1.5 RS485 BIASING AND TERMINATION...................................................10
1.6 NETWORK ADDRESSING.......................................................................10
1.6.1 Changing the Device Address ...................................................10
1.7 ENABLING/DISABLING FRONT PANEL RESET...................................12
1.8 D-100-P1 POINT DATABASE..................................................................12
1.8.1 Application Number..................................................................13
1.8.2 D-100-P1 Point Database ...........................................................14
2.0 NETWORK IMPLEMENTATION STRATEGIES ................................................15
2.1 IMPLEMENTATION STRATEGIES .........................................................15
2.2 OTHER FUNCTIONALITY......................................................................16
APPENDIX
A-1 D-100 PROCESSOR BOARD

11451 Belcher Road South, Largo, FL 33773 • USA • Tel [phone] • Fax [phone] • [email protected]
D-100-P1 Flow Display Manual 03/18 - 0660-5 / 18343 Page 4

11451 Belcher Road South, Largo, FL 33773 • USA • Tel [phone] • Fax [phone] • [email protected]
D-100-P1 Flow Display Manual 03/18 - 0660-5 / 18343 Page 5
SECTION 1: INTRODUCTION
1.1 PURPOSE OF THIS GUIDE
The purpose of this guide is to provide installation and commissioning procedures and basic
operating and servicing instructions for the ONICON D-100-P1 network interface.
1.2 TYPICAL D-100 NETWORK INTERFACE MODULE
The D-100 is a totalizing display module that provides a local indication of liquid, gas or steam
ow rate and total data. It can also be provided with an optional Siemens P1 RS485 network
interface to communicate data to the building control network.
D-100
SCROLL RESET PROGRAM
ONICON
3864
Steam Building
Domestic Water Supply
Flow rate and total data to
Data Acquisition System or
Building Control System
120VAC or 24VAC
Input Voltage
1.3 SPECIFICATIONS
SIEMENS P1 NETWORK INTERFACE
Transceiver: 2-wire, half duplex
MAC address (device address) range: 1-99, (default: 017)
Baud rate: 4800
Termination: None

11451 Belcher Road South, Largo, FL 33773 • USA • Tel [phone] • Fax [phone] • [email protected]
D-100-P1 Flow Display Manual 03/18 - 0660-5 / 18343 Page 6
1.4 NETWORK SIGNAL CONNECTIONS
1.4.1 Standard Network Interface
P1 RS485, 2-wire (half duplex) serial output connections are connected to terminals as
shown. Do not exceed 4.4 in-lb (0.5Nm) of torque when tightening.
CAUTION
Only qualied service personnel should make connections between the D-100 and the user’s
external equipment. ONICON assumes no responsibility for damage caused to the external
equipment as a result of an improper installation.
!
CAUTION
Incoming and outgoing RS485 cable shield wires should be connected together, but must not be
connected to the D-100.
!
P1 (-)
P1 (+)

11451 Belcher Road South, Largo, FL 33773 • USA • Tel [phone] • Fax [phone] • [email protected]
D-100-P1 Flow Display Manual 03/18 - 0660-5 / 18343 Page 7
1.4.2 Optional Network Interface With Optional Isolated Digital Pulse Input (Di3)
The D-100-P1 Display can be provided with an auxiliary input pulse for totalizing pulse
outputs from external devices such as water or gas meters. Pulses are accumulated in an
internal register, and the totalized value is available on the network. This register can be
zeroed via the network.
If the auxiliary pulse input option was ordered at the same time the display was ordered,
it will arrive fully congured and ready to use. If it was ordered after the display was
delivered and is being installed as a eld upgrade, it may be necessary to congure the
pulse input. The information is provided below and on the following pages:
The input pulse must meet the following criteria:
1. Frequency input range, 50 Hz maximum
2. 10 millisecond minimum pulse duration
Input Pulse Denition:
In order to congure the communications card for an auxiliary input pulse, you must
rst determine which type of pulse your meter produces. The allowable types of input
pulses are described on the following pages. Based on the type of pulse, set the selector
switch (S1) on the communications circuit board (Fig. 1) to the correct setting.
Fig. 1
AUX PULSE INPUT (Di3)
CONNECTOR (T2)

11451 Belcher Road South, Largo, FL 33773 • USA • Tel [phone] • Fax [phone] • [email protected]
D-100-P1 Flow Display Manual 03/18 - 0660-5 / 18343 Page 8
Powered Pulse:
This type of output refers to a pulse which has an associated voltage with it (see Fig. 2).
Set the selector switch, S1 to Pwrd Pulse. The allowable voltage range is 5-24 VDC. The
input impedance is set at the factory to be 11 KOHM via the impedance selector jumper
(J1, see Fig. 1). A lower impedance, 3 KOHM can be selected if required by the instrument
providing the pulse output. Consult the instrument manufacturer or ONICON if you are
uncertain as to the proper jumper selection.
Fig. 2
Open Collector (Sourcing):
This type of output refers to an open Collector Switch congured for a sourcing function
(see Fig. 3). Set the selector switch, S1 to SRC. The switch must be rated for at least 20 mA
at 20 VDC.
Fig. 3
Di3 In (+)
Di3 In (-)
Di3 In (+)
Di3 In (-)
ONICON
BTU METER
ONICON
BTU METER

11451 Belcher Road South, Largo, FL 33773 • USA • Tel [phone] • Fax [phone] • [email protected]
D-100-P1 Flow Display Manual 03/18 - 0660-5 / 18343 Page 9
Open Collector Sinking or Dry Contact:
This type of output refers to an open collector switch congured in a current sinking
arrangement or a dry contact switch (see Fig. 4 and 5). Set the selector switch, S1 to Sink.
In either case, the switch must be rated for at least 20 mA at 20 VDC.
Fig. 4
Fig. 5
Di3 In (+)
Di3 In (-)
Di3 In (+)
Di3 In (-)
ONICON
BTU METER
ONICON
BTU METER

11451 Belcher Road South, Largo, FL 33773 • USA • Tel [phone] • Fax [phone] • [email protected]
D-100-P1 Flow Display Manual 03/18 - 0660-5 / 18343 Page 10
1.5 RS485 BIASING AND TERMINATION
The ONICON D-100-P1 does not provide biasing voltage or termination to the RS485 network. A
120Wtermination resistor should be used when the display is installed at the end of the line.
1.6 NETWORK ADDRESSING
Before the D-100 can communicate on the P1 network, the appropriate device address must be
programmed into the display. The P1 network address for ONICON D-100 Flow Displays may
be set to any address from 1 to 99. This address is set at the display. Section 1.6.1 details the
procedure for changing this address.
1.6.1 Changing the Device Address
Every ONICON D-100 is individually programmed at the factory with application specic
data provided by the customer during the ordering process, and this may include network
addressing information. If the device address information was provided, the display
will be programmed with that number. If no address is provided, ONICON displays are
programmed with a default address of 017. The address may be changed at the D-100
using the procedure outlined in the table below.
STEP ACTION REACTION COMMENT
0Obtain a device address from the
network administrator.
The device address is
a three digit number
between 1 - 99, excluding
zero.
1
With the display running, open
the front panel and locate switch
DEV ADD/PROG ENAB. Press
DEV ADD/PROG ENAB and then
release it.
None
The DEV ADD/PROG ENAB
is located on the processor
board. (See appendix page
A-1.)
2 Close the front panel.
3
Press the PROGRAM button. (If
you do not press the PROGRAM
button, the display will revert to
the RUN mode after 5 minutes.)
The D-100 changes to
PROGRAM mode and the
DEVICE ID page will
appear with the rst digit
of the address ashing.
The PROGRAM button is on
the front panel.

11451 Belcher Road South, Largo, FL 33773 • USA • Tel [phone] • Fax [phone] • [email protected]
D-100-P1 Flow Display Manual 03/18 - 0660-5 / 18343 Page 11
STEP ACTION REACTION COMMENT
4
Successively press the SCROLL
button to increment the number to
the desired value from 0-9.
The number increments
by one each time you
press the button.
The SCROLL button is on
the front panel.
5 Press the RESET button. The second character
blinks.
The RESET button is on the
front panel.
6
Successively press the SCROLL
button to increment the number to
the desired value from 0-9.
The number increments
by one each time you
press the button.
The SCROLL button is on
the front panel.
7 Press the RESET button. The third character
blinks.
The RESET button is on the
front panel
8
Successively press the SCROLL
button to increment the number to
the desired value from 0-9.
The number increments
by one each time you
press the button.
The SCROLL button is on
the front panel.
9Once the correct value has been
entered, press PROGRAM.
The FRONT PANEL
RESET page appears.
It is not necessary to change
anything on this page.
10 Press the PROGRAM button. The SAVE CHANGES
page appears.
The new device address
must be saved to take
effect.
11 Press the SCROLL button.
The N changes to Y on
the SAVE CHANGES
page.
The Y must be selected in
order for the new address to
take effect.
12 Press the PROGRAM button.
The new address is saved
and the display reverts to
the RUN mode.
13
Open the front panel and locate
the RESET switch. Press to reset
the D-100.
When polled, the D-100
will automatically begin
to communicate with the
network.
RESET is located along the
top of the processor board.
(See appendix page A-1.)

11451 Belcher Road South, Largo, FL 33773 • USA • Tel [phone] • Fax [phone] • [email protected]
D-100-P1 Flow Display Manual 03/18 - 0660-5 / 18343 Page 12
1.7 ENABLING / DISABLING FRONT PANEL RESET
The D-100-P1 Display accumulates totals in nonvolatile memory. This memory can be zeroed
directly at the display or via the network. The direct method requires the operator scroll the LCD
display until the total is displayed. The operator must then press the reset button on the front
panel. The total reverts to zero. The next total to be zeroed is selected and the process repeated.
The front panel reset function, however, must be enabled. It is shipped “Disabled” from the
factory. To enable the function, follow the instructions in the table below.
STEP ACTION REACTION COMMENT
1 With the display running,
open the front panel and
locate S-4. Press S-4.
None Switching S-4 arms the
front pane PROGRAM
button for a period of
ve minutes.
2 Close the front panel. None The display remains in
the run mode.
3 Press the PROGRAM
button.
The top line of the LCD shows
eight P characters, PPPPPPPP. The
bottom line shows P1 DEVICE ID
XX.
XX can be any two
number digits. The rst
digit will blink. Take no
action.
4 Press the PROGRAM
button.
Top line: PPPPPPPP
Bottom line: P1 APP NO XXXX
Take no action.
5 Press the PROGRAM
button.
Top line: PPPPPPPP
Bottom line: FRONT PANEL
RESET N
6 Press the SCROLL button. The last N character on the bottom
line changes to Y.
RESET N indicated
“disabled.”
RESET Y indicates
“enabled.”
7 Press the PROGRAM
button.
Top line: PPPPPPPP
Bottom line: SAVE CHANGES N
8 Press the SCROLL button. The N on the bottom line changes
to Y.
Bottom line: SAVE CHANGES Y
9 Press the PROGRAM
button.
The bottom line disappears. After a
moment a run mode page appears.
After a short delay, the
display enters its run
mode.
1.8 D-100-P1 POINT DATABASE
The Point Database table on the next page lists all of the points used by the D-100-P1 Flow
Display. NOTE: Also refer to the Siemens’ Application Note, Document No. XXX-XXXX for more
information.

11451 Belcher Road South, Largo, FL 33773 • USA • Tel [phone] • Fax [phone] • [email protected]
D-100-P1 Flow Display Manual 03/18 - 0660-5 / 18343 Page 13
1.8.1 Application Number
The application number is assigned to the display based on the calibration parameters
supplied at the time the display was programmed. If the system parameters change, please
contact ONICON for assistance in determining the correct application number.
TABLE OF STANDARD D-100-P1 APPLICATION NUMBERS
Siemens
Application
Number
Point 4 Point 5 Point 6 Points 11 & 12 Date Added
Displayed
Flow Rate
Ai3
Generic Analog
Input 1
Ai4
Generic Analog
Input 1
Displayed
Flow Total
1001 GPM x 1 NONE x 1 NONE x 1 GALLONS x 10 3/9/2011
1002 GPM x 1 NONE x 1 NONE x 1 GALLONS x 100 3/9/2011
1003 GPM x 1 NONE x 1 NONE x 1 GALLONS x 1,000 3/9/2011
1004 GPM x 1 NONE x 1 NONE x 1 GALLONS x 10,000 3/9/2011
1005 GPM x 10 NONE x 1 NONE x 1 GALLONS x 10,000 3/9/2011
1006 L/S x 1 NONE x 1 NONE x 1 LITERS x 100 3/9/2011
1007 L/S x 1 NONE x 1 NONE x 1 LITERS x 1,000 3/9/2011
1008 L/S x 1 NONE x 1 NONE x 1 LITERS x 10,000 3/9/2011
1009 SCFH x 1 NONE x 1 NONE x 1 SCF x 1 3/9/2011
1010 SCFH x 1 NONE x 1 NONE x 1 SCF x 10 3/9/2011
1011 SCFH x 1 NONE x 1 NONE x 1 SCF x 100 3/9/2011
1012 SCFH x 10 NONE x 1 NONE x 1 SCF x 100 3/9/2011
1013 SCFH x 10 NONE x 1 NONE x 1 SCF x 10,000 3/9/2011
1014 SCFH x 1 NONE x 1 NONE x 1 SCF x 10 3/9/2011
1015 SCFH x 1 NONE x 1 NONE x 1 SCF x 100 3/9/2011
1016 SCFH x 1 NONE x 1 NONE x 1 SCF x 1,000 3/9/2011
1017 SCFH x 1 NONE x 1 NONE x 1 SCF x 10,000 3/9/2011
1018 NCMH x 1 NONE x 1 NONE x 1 NCM x 10 3/9/2011
1019 NCMH x 1 NONE x 1 NONE x 1 NCM x 100 3/9/2011
1020 PPH x 1 NONE x 1 NONE x 1 LBM x 1 3/9/2011
1021 PPH x 1 NONE x 1 NONE x 1 LBM x 10 3/9/2011
1022 PPH x 1 NONE x 1 NONE x 1 LBM x 100 3/9/2011
1023 PPH x 10 NONE x 1 NONE x 1 LBM x 100 3/9/2011
1024 PPH x 10 NONE x 1 NONE x 1 LBM x 1,000 3/9/2011
1025 KPH x 1 NONE x 1 NONE x 1 KG x 1 3/9/2011
1026 KPH x 1 NONE x 1 NONE x 1 KG x 10 3/9/2011
1027 KPH x 1 NONE x 1 NONE x 1 KG x 100 3/9/2011
1028 KPH x 10 NONE x 1 NONE x 1 KG x 100 3/9/2011
1029 KPH x 10 NONE x 1 NONE x 1 KG x 1,000 3/9/2011
1030
1031
1032
1033
1034
1035

11451 Belcher Road South, Largo, FL 33773 • USA • Tel [phone] • Fax [phone] • [email protected]
D-100-P1 Flow Display Manual 03/18 - 0660-5 / 18343 Page 14
1.8.2 D-100-P1 Point Database
P1 POINTS
Pt Name/Range Type Category COV OVR Default Initial Current
1 Address Range: 1-99 02 LAO NO YES 99 11HNone
2 Application 02 LAO NO NO 199910 199910 None
4 Flow Rate - 0-32,767 03 LAI YES NO 0 0 Integer
5 Ai3 - Generic Analog Input 1 03 LAI YES NO 0 0 Integer
6 Ai4 - Generic Analog Input 2 03 LAI YES NO 0 0 Integer
8 Operating Mode: 1/Forward, 2/Reverse 03 LDI NO NO 0 0 Byte
11 W0-M1Volume: 000,000-009,999 03 LAI NO NO 0 0 Integer
12 W1-M1 Volume: 010,000-999,999 03 LAI NO NO 0 0 Integer
15 W0-M2 Volume: 000,000-009,999 03 LAI NO NO 0 0 Integer
16 W1-M2 Volume: 010,000-999,999 03 LAI NO NO 0 0 Integer
17 W0-AuxiIn-1: 000,000-009,999 03 LAI NO NO 0 0 Integer
18 W1-AuxiIn-2: 010,000-999,999 03 LAI NO NO 0 0 Integer
19 Not Used
20 Point 20, Override Time (Hours)
Range 0-FF
02 LAO NO YES 1 1 None
22 M-1 V Reset - 0/Off, 1/Reset 01 LDO NO YES 0 0 Byte
24 M-2 V Reset - 0/Off, 1/Reset 01 LDO NO YES 0 0 Byte
25 AuxIn Reset - 0/Off, 1/Reset 01 LDO NO YES 0 0 Byte
29 DAY.NGT
ON=Night; OFF=Day; Default=OFF
01 LDO NO YES 0 0 Byte
99 ERROR STATUS Bit Oriented 01 LAO NO YES 0 0 Integer
100 Point 100
Factory Flag
Factory Flag is not a point in the sense that the others are. It is referenced only
by the Memorize Point Command. Other commands should NAK it with “POINT
DOES NOT EXIST”.
NOTE: Also refer to the Siemens’ Application Note, Document No. XXX for additional information.

11451 Belcher Road South, Largo, FL 33773 • USA • Tel [phone] • Fax [phone] • [email protected]
D-100-P1 Flow Display Manual 03/18 - 0660-5 / 18343 Page 15
SECTION 2.0: NETWORK IMPLEMENTATION STRATEGIES
2.1 IMPLEMENTATION STRATEGIES
Monitoring
Several D-100 parameters are available for monitoring purposes. These include Volume Rate
(Point 4), Ai3 - Generic Analog Input 1 (Point 5), and Ai4 - Generic Analog Input 2 (Point 6).
These points can be unbundled for use in trending the performance of the hydronic system or
used in various global control strategies.
Totalization
Three D-100-P1 Display parameters are available for accumulating totalized data. These are Mode
1 Volume Total (Points 11 & 12), Mode 2 Volume Total (Points 15 & 16) and (optional) auxiliary
input (Points 17 & 18). Typically the Mode 1 and Mode 2 Volume Total points of the D-100-P1
Display are used to quantify the amount of water consumed in custody transfer applications.
They may also be used to accumulate total consumption for use in ongoing plant or system
efciency measurements.
D-100-P1 Display totalization registers are 7 digit registers. User dened units and multipliers
are then applied to these values. This is required to allow for the accumulation of totals over a
reasonable time period without exceeding the capacity of the register. P1 variables are limited
in range to 32,767. In order to properly convey the D-100 information, each totalization register
is represented by two separate type 3 LAI points. The rst point represents digits from 0 - 9,999.
The second point represents the digits from 10,000 to 9,999,999. The user-selected multiplier is
applied to the units for the rst word. For the second point, the multiplier is adjusted by a factor
of 10,000, then applied to the units.
Multipliers
ONICON D-100 Volume Rate and Accumulation Points have multipliers. Multipliers are 1, 10,
100, 1,000, 10,000, 100,000 or 1,000,000. For points 11, 12, 15, 16, 17, and 18 the point descriptor
will contain the multiplier. The 11 multipliers are as follows:
Characters Multiplier
1 1
X 10
C 100
K 1,000
XK 10,000
CK 100,000
M 1,000,000
XM 10,000,000
CM 100,000,000
KM 1,000,000,000
XKM 10,000,000,000

11451 Belcher Road South, Largo, FL 33773 • USA • Tel [phone] • Fax [phone] • [email protected]
D-100-P1 Flow Display Manual 03/18 - 0660-5 / 18343 Page 16
Example
The D-100-P1 Display is running Application xxxx. The display shows the Volume Total as
122604 GAL x 100. The associated P1 variables would be as follows:
Point 11 – 2604 CGAL
Point 12 – 12 MGAL
To bring this value into the APOGEE Automation System, assign a Virtual Point for
Volume Total:
Volume Total = (Point 11 x 100) GAL+ (Point 12 x 1,000,000) GAL
Volume Total = (2604 x 100) GAL+ (12 x 1,000,000) GAL
Volume Total = 260400 GAL + 12000000 GAL
Volume Total = 12260400 GAL
NOTE: Volume Total to equal ONICON display you must divide the number above by 100 to get
GAL x 100. 12260400 / 100 = 122604 GAL x 100
2.2 OTHER FUNCTIONALITY
Each of the following functions of the D-100-P1 Display are also available and may be required,
depending on the application.
Mode Status
Mode Status (Point 8) provides a separate indication of ow direction in bi-directional ow
applications. For bi-directional ow applications, Mode 1 represents ow in the direction of the
arrow on the ow meter enclosure.
Resetting Totals
Separate type 1 LDO points are provided to reset each totalizing register. These are Mode 1
Volume Total Reset (Point 22) Mode 2 volume Total Reset (Point 24, and Auxiliary Input Total
Reset (Point 25).
Isolated, Non-polarized Dry Contact Pulse Output
An optional pulse output for the external accumulation of energy increments is available. Pulse
durations of 0.5-, 1.0-, 2.0-, or 6-seconds can be selected by the user.

11451 Belcher Road South, Largo, FL 33773 • USA • Tel [phone] • Fax [phone] • [email protected]
D-100-P1 Flow Display Manual 03/18 - 0660-5 / 18343 Page 17
APPENDIX
A-1 D-100 PROCESSOR BOARD

11451 Belcher Road South, Largo, FL 33773 • USA • Tel [phone] • Fax [phone] • [email protected]
D-100-P1 Flow Display Manual 03/18 - 0660-5 / 18343 Page A-1
D-100 FLOW DISPLAY PROCESSOR BOARD
Reset
Temp Test
Prog Mode
Enable
Device Address
Program Enable
Serial Comm