OPERTIS eLOCK ES6610 User manual

Operating instructions
Framed Door System
ES6610, ES7610

eLOCK GB
Operating Instructions Framed Door System ES6610, ES7610
05/2012 OPERTIS 3
Contents
1Introduction ..................................................................................................................4
About these instructions............................................................................................... 4
Explanation of the Symbols and Signal Words Used................................................... 4
Target group................................................................................................................. 4
OPERTIS Support........................................................................................................ 4
Up-to-date status of the information............................................................................. 5
2Product Description.....................................................................................................5
Component parts.......................................................................................................... 5
Functional principle ...................................................................................................... 6
Detailed information ..................................................................................................... 6
3Intended Use.................................................................................................................6
Area of use................................................................................................................... 6
Condition of the product ............................................................................................... 6
Ambient conditions....................................................................................................... 7
Power supply................................................................................................................ 7
Residual risk................................................................................................................. 7
4Safety Instructions.......................................................................................................7
5Use and Operation......................................................................................................10
Programming fittings and identifiers........................................................................... 10
Changing the batteries ............................................................................................... 10
Visual signals ............................................................................................................. 11
6Servicing, Cleaning and Maintenance......................................................................12
Intervals...................................................................................................................... 12
Cleaning and maintenance ........................................................................................ 12
Servicing .................................................................................................................... 13
7Problems and Solutions ............................................................................................14
8Product Specifications...............................................................................................15
Declaration of conformity ........................................................................................... 15
Dimensions ................................................................................................................ 16
Technical data............................................................................................................ 18
9Disposal ......................................................................................................................19
Product....................................................................................................................... 19
Batteries ..................................................................................................................... 19

GB eLOCK
Framed Door System ES6610, ES7610 Operating Instructions
4 OPERTIS 05/2012
1 Introduction
About these instructions
These instructions contain important notes and information on operation of
the ES6610and ES7610 Framed Door systems.
Read through the instructions carefully and attentively.
Keep the instructions in a safe place and pass them on to each
subsequent user of the Framed Door systems.
Explanation of the Symbols and Signal Words Used
WARNING Indicates risks which could result in fatal or severe
personal injuries.
CAUTION Indicates risks which could result in fatal or severe
personal injuries.
CAUTION
Indicates risks which could result in damage to
property.
Note Denotes information, notes and tips on optimum use
of the instructions and the product.
Target group
These instructions are directed at competent personnel entrusted with the
servicing, maintenance and disposal of trouble-free operation of the
Framed Door system and who has successfully completed suitable
vocational training for these activities or has had the necessary
appropriate experience.
OPERTIS Support
If you have any questions extending beyond the information provided in
these instructions, please contact
OPERTIS GmbH
Prof.-Bier-Straße 1-5
D-34454 Bad Arolsen
Tel.: [phone]
Fax: [phone]
E-Mail: [email protected]

eLOCK GB
Operating Instructions Framed Door System ES6610, ES7610
05/2012 OPERTIS 5
Up-to-date status of the information
All details on the product, images, dimensions and models correspond to
the status at the time the product is delivered. We reserve the right to
make changes due to technical progress and the resulting continuous
improvement process to which our products are subjected.
The current version of these instructions and further information is also
available on our internet site www.opertis.de.
Dated 05/2012
2 Product Description
Component parts
The following drawing shows the main component parts of the Framed
Door system:
1 Read-out unit
2 Evaluator unit
3 Electro-mechanical lock
4 Control latch
5 Latch
6 Dead bolt
4
5
6

GB eLOCK
Framed Door System ES6610, ES7610 Operating Instructions
6 OPERTIS 05/2012
Functional principle
The OPERTIS eLOCK lock system ensures continuous public and
commercial building fitout. Special fitting solutions are available for
different door types.
The Framed Door system includes a self-locking lock which automatically
locks when the door is closed. There is no locking in the conventional
sense by means of knobs or keys; mechanical locking is no longer
necessary.
In the Framed Door system the inner lever handle is always coupled in.
The integrated anti-panic function pulls back the latch and bolt when the
inner lever handle is pressed; the doors can always be opened from the
inside.
In the Framed Door system the outer lever handle has no function in the
decoupled state: It can be pressed but does not have any connection with
the lock latch and bolt. In this state the door cannot be opened using the
outer lever handle. Access organisation is realised by short-term coupling-
in of the otherwise idle (disengaged) outer lever handle after holding an
identifier in front of the antenna. If the coupled-in outer handle lever is
pressed the latch and bolt are pulled back.
There is no unlocking in the conventional sense by means of knobs or
keys; mechanical unlocking is no longer necessary.
Management and programming, among other things the issue of access
authorisations, takes place using the eLOCK Center management
software. Optionally, programming with eLOCK LernLösch is also possible
via three programming keys without additional software.
Passive identifiers without their own power supply are available for
authorisation at the fittings in different forms such as key fobs, cards or
customer-specific forms.
Detailed information
Further information on the product is given in Section 8 "Product
Specifications".
3 Intended Use
Area of use
The Framed Door system has been designed for use in narrow framed
doors at internal and external doors. It is not permitted to use it outdoors,
e.g. in fencing.
Condition of the product
Framed Door systems may only be used if they are in a technically perfect
condition.
Independent modifications and changes to the product are not allowed.

eLOCK GB
Operating Instructions Framed Door System ES6610, ES7610
05/2012 OPERTIS 7
Ambient conditions
Use in a particularly polluted environment, e.g. in aggressive gases, high
humidity, in extreme temperatures or in a very dusty environment, is not
allowed. If you have any questions, please contact OPERTIS Support.
Power supply
All battery operated fittings activate acoustic and/or optical battery flat
warnings and controlled failed locking if the battery output in the fitting is
fading. The battery should then be replaced without delay.
Residual risk
If used properly and if the maintenance instructions are followed, this
product will support your property security.
However, the following residual risks cannot be excluded:
In the event of failure of the electronics there is a risk of locking out. In
this case the door can only be opened from the outside with
mechanical aids. In this case, please contact OPERTIS Support.
If the battery flat warning is repeatedly ignored the Framed Door
system stops all activities (Active Power Off). The door cannot be
opened from the outside. This state is retained in until the battery has
been replaced and then an external power supply has been provided.
In Active Power Off, i.e. if the battery is completely flat or missing, the
Framed Door system stops all activities. The door can then only be
opened from the outside with the external power supply (EPS) ES6781
for ES5000 plus systems or the ES7781 for eLOCK and eLOCK
LernLösch systems.
4 Safety Instructions
The following safety instructions must be read and followed before use!
OPERTIS does not accept any liability whatsoever for personal losses or
injuries or damage to property caused by failure to note and follow these
instructions!
WARNING
Risk of personal injuries
The Framed Door system has been tested and approved for
use in framed fire doors and framed smoke control doors. If
used in a fire door or smoke control door it must also be
listed in the "monitoring design features" (list of approved
products) of the relevant profile manufacturer.

GB eLOCK
Framed Door System ES6610, ES7610 Operating Instructions
8 OPERTIS 05/2012
WARNING
Risk of personal injuries
An approved framed door version with anti-panic function
must be installed in the escape direction for doors in escape
routes.
WARNING
Risk of personal injuries
If the Framed Door system is used in doors in escape routes
an approved lock model (lever handle side with panic
function in the direction of escape) must be installed.
Otherwise the door does not have the anti-panic function.
WARNING
Danger of personal injury
from the battery
Any improper contact with the battery can lead to damage to
the health. The following instructions must be noted:
Only use batteries supplied or approved by OPERTIS.
Do not open, solder or weld the batteries.
Do not throw the batteries into fire.
Do not recharge the batteries.
Remove empty batteries immediately from the fitting.
Store batteries out of the reach of children.
Do not touch leaking batteries without appropriate
protection. Avoid contact with the eyes or mouth.
CAUTION
Danger of material damage
Malfunctions can occur if unapproved battery types are used.
The fitting does not signal any battery warnings and does not
switch to the secured end state Active Power Off.
Only use battery types approved by OPERTIS.
CAUTION
Risk of locking in or out
The door cannot be opened without a fully functional fitting, if
the latch drops into the lock.
Leave the door open during installation and while changing
the battery or ensure that the door can be opened at any time
without using the fitting.

eLOCK GB
Operating Instructions Framed Door System ES6610, ES7610
05/2012 OPERTIS 9
CAUTION
Unauthorised access
After opening the door, let go of the outer lever handle.
Otherwise the electronic lock of the framed door system
cannot uncouple and lock the door if the lever handle is kept
pressed for longer than 2 min. after the opening time (default
20 sec.). The framed door system then automatically tries to
uncouple the outer lever handle at defined intervals.
CAUTION
Unauthorised access
The inner lever handle of the Framed Door system is coupled
as an anti-panic lock. This enables the door to be opened at
any time using the inner lever handle. You should note this,
above all when using the fitting in publicly accessible doors
and doors through which the inner lever handle can be easily
accessed from the outside.
CAUTION
Unauthorised access
When delivered the Framed Door systems are in construction
site mode. Access is possible with any OPERTIS identifier,
even if they are not programmed.
Program the authorisations immediately after installation to
prevent unauthorised access; see eLOCK system
documentation software. Check time and if necessary reset.

GB eLOCK
Framed Door System ES6610, ES7610 Operating Instructions
10 OPERTIS 05/2012
5 Use and Operation
Programming fittings and identifiers
Fittings and identifiers are programmed using the eLOCK Center
management centre or the eLOCK LernLösch system. Detailed
information on this is given in the eLOCK system documentation software.
Changing the batteries
Note
Note the battery type information in Section "Technical data".
Proceed as follows:
Step Activity Figure
1 Undo countersunk screw on
the underside of the
evaluator unit cover,
2 Remove the cover of the
evaluator unit.
3 Remove batteries.
4 Insert the new batteries in the
battery compartment
ensuring the battery polarity
is correct.
5 Replace the cover and screw
onto the underside.
6 Check date and time and if
necessary reset, see eLOCK
software system
documentation.