Waferlock L700 User manual

Before setting the programming card, it is
allowed to use any cards/badges to unlock the
door, then you will hear 1 beep followed by red
and green lights alternately flashing 3 times.
WAFERLOCK CORPORATION
Tel: [phone] Fax: [phone]
No. 16 Ke Yuan 2nd Rd., Central Taiwan Science Park
Taichung city 407, Taiwan.
E-mail: [email protected]
L700
ELECTRONIC
HANDLE LOCK
User Manual
Default Unlock The Door With User Card
Delete Individual User Card
Delete Lost User Card
Set Programming Card
Program New User Card
Approach the reader with programming
card, you will hear 1 beep, and the red light
starts flashing.
1
Approach the reader with programming
card, you will hear 3 beeps, and the red light
starts flashing.
1
Approach the reader with programming
card, you will hear 3 beeps, then remove
the programming card, and the red light
starts flashing.
1
Approach the reader with card/badge, you
will hear 1 beep followed by the green light
flashing 1 time. The new user card/badge is
programed.
2
Tap the card on the reader for 10 seconds,
you will hear 3 beeps followed by the
green light flashing 3 times. The
programming card is successfully set.
2
Your Warranty covers all manufacturers' defects in
workmanship and material. It does not cover any unit
that is damaged beyond normal usage, by improper
installations, by contacts to chemicals, or any other
acts or omissions unsanctioned within the user manual.
All components are covered for one (1) year after the
date of purchase or installation from supplier.
The user is required to provide dated proof of
purchase. Waferlock or its authorized distributor will
determine if there is a warrantable condition associated
with material and/or manufacturing workmanship.
If the lock conforms to the warranty conditions, the
lock will be repaired free of charge. The shipping
freights would be at owner's expense.
The warranty does not include any further obligation
whatsoever, including but not limited to the installation
of the replacement unit to the customer's lock.
All other warranties, express or implied, are disclaimed.
All collateral agreements, which purport to modify this
limited warranty, are of no eect.
This device has been tested to and conforms to the
regulatory requirements of the European Union and
has attained CE Marking. The CE Mark is a conformity
marking consisting of the letters “CE”. The CE Mark
applies to products regulated by certain European
health, safety and environmental protection
legislation. The CE Mark is obligatory for products it
applies to: the manufacturer axes the marking in
order to be allowed to sell his product in the European
market.
This product conforms to the essential requirements
of the R&TTE directive 1999/5/EC in order to attain CE
Marking.
The CE Marking is not a quality mark. Foremost, it
refers to the safety rather than to the quality of a
product. Secondly, CE Marking is mandatory for the
product it applies to, whereas most quality markings
are voluntary.
Your Warranty
CE Marking
Note
If you hear 2 beeps followed by the
red light flashing 2 time, it means
the card/badge is invalid.
Approach the reader with programed user
card/badge, you will hear 1 beep followed
by green light flashing 1 time, then the door
is unlocked.
1
PROGRAMMING
Red
1 “beep” sound
PROGRAMMING
Red
3 “beep” sound
PROGRAMMING
Red
3 “beep” sound
USER
Green X 1
1 “beep” sound
Tap the card/badge on the reader for 5
seconds, you will hear 1 long beep followed
by the red light flashing 5 times. The
individual user card has been deleted.
3
Approach the reader with individual user
card/badge, you will hear 1 beep followed
by the green light flashing.
2
USER
Red X 5
1 long “beep” sound
PROGRAMMING
Green X 3
3 “beep” sound
Approach the reader with programming
card, you will hear 3 beeps, then remove the
programming card, and the red light starts
flashing.
1
Approach the reader with shadow card,
which used to be paired by shadow user
card, you will hear 1 beep and the green light
starts flashing.
2
1
0
s
e
c
USER
Green X 1
1 “beep” sound
USER
Green
1 “beep” sound
SHADOW
Green
1 “beep” sound
PROGRAMMING
Red
3 “beep” sound
(Shadow Version Only)
Note
1. After tapping the programming card on the reader,
if you do not swipe the user card/ badge on the
reader within 10 seconds, the programming mode
will be cancelled.
2. The maximum of 250 user cards/badges can be
programed. By reaching the maximum limit, you
can hear 10 short beeps followed by red and green
lights alternately flashing 3 times.
Note
1. If the card did not approach for 10 seconds, you will
hear 2 beeps followed by the red light flashing 2
times.
2. Programming card can be used for adding/
deleting user cards/badges, but cannot be used to
unlock the door.
3. Only 1 lock can be set by 1 programming card,
hence, the programming card is far more important
for users.
PROGRAMMING
1 “beep” sound
Red/Green LED X 3

PROGRAMMING
Delete All User Cards
Set Passage Card
SHADOW
Red X 5
1 long “beep” sound
PASSAGE
Green X 5
1 long “beep” sound
Red
3 “beep” sound
Approach the reader with programming
card, you will hear 3 beeps, then remove
the card, and the red light starts flashing.
1
Tap the programming card on the reader
again, you will hear 3 beeps, then remove
the card again and the red light keeps
flashing.
2
PROGRAMMING
Red
3 “beep” sound
Approach the reader with programming
card, you will hear 3 beeps and the red light
starts flashing.
1
Approach the reader with passage card,
you will hear 1 beep followed by the green
light flashing 1 time. The passage card has
been set.
2
PROGRAMMING
1 long “beep” sound
Red X 5
Tap the programming card on the reader for
the third time, you will hear 1 long beep
followed by the red light flashing 5 times. All
user cards have been deleted.
3
PASSAGE
Green X 1
1 “beep” sound
Set User Card As Passage Mode
PASSAGE
Green
1 “beep” sound
Approach the reader with passage card,
you will hear 1 beep followed by the green
light flashing.
1
Tap the user card on the reader for 5
seconds, you will hear 1 long beep followed
by the green light flashing 5 times. The user
card has been set as passage mode.
2
USER
Green X 5
1 long “beep” sound
Set The Lock As Passage Mode
USER
Green
1 “beep” sound
Approach the reader with user card,
which used to be set as passage mode,
you will hear 1 beep followed by the green
light flashing.
1
Tap the passage card on the reader for 5
seconds, you will hear 1 long beep followed
by the green light flashing 5 times. The lock
has been set as passage mode.
2
USER
Red X 5
1 “beep” sound
Set User Card As Standard Mode
PASSAGE
Green
1 long “beep” sound
Approach the reader with passage card,
you will hear 1 beep and the green light
starts flashing.
1
Tap the user card on the reader for 5
seconds, you will hear 1 long beep followed
by the red light flashing 5 times. The user
card has been set as standard mode.
2
PROGRAMMING
Green
1 long “beep” sound
Set WAFERKEY (Optional)
Low Power Warning
Emergency External Power Supply
Approach the reader with programming
card, you will hear 3 beeps, and the red
light start flashing
1
Tap the card on the reader for 5 seconds,
you will hear 1 long beep and the green light
starts flashing. The lock has been set as
mobile paired mode, then please follow the
instruction of the APP to finish the setup.
2
If the lock did not successfully pair with
mobile phone within 30 seconds, the mobile
paired mode will be cancelled.
3
If the lock battery is low, there is an acoustic
warning for the user with 3 short beeps 5 times,
followed by orange light flashing. Please replace
a new battery to keep lock operating well.
USER
Red X 5
1 long “beep” sound
Set The Lock As Standard Mode
USER
Green
1 “beep” sound
Approach the reader with user card,
which used to be set as passage mode,
you will hear 1 beep followed by green
light flashing.
1
Tap the card on the reader for 5 seconds,
you will hear 1 long beep followed by red
light flashing 5 times. The lock has been set
as standard mode.
2
Tap the card/badge on the reader for 5
seconds, you will hear 1 long beep followed
by the red light flashing 5 times. The
individual user card has been deleted.
3
PROGRAMMING
3 “beep” sound
Note
1. Passage card cannot be deleted; it can only be
reset.
2. Only 1 passage card can be set on 1 lock.
3. Passage card is only available from WAFERLOCK
or its distributors.
Note
1. The lost user card, which must originally be paired
by shadow card, is allow to be deleted.
2. Both User Card (Shadow Version) and Shadow
Card are only available from WAFERLOCK or its
distributors.
Note
Please download WAFERKEY APP on iOS Apple
Store or Android Google Play Store.
Red