Securam SafeLogic C10 D-Drive User manual

1
Important:
• For indoor use only.
• Battery Low Voltage: The entrypad will alert low battery when battery voltage is
low. PLEASE REPLACE THE BATTERY IMMEDIATELY.
FEATURES:
1. Manager Code (ID 01):
a) Open lock.
b) Change code.
c) Add/delete user.
d) Disable/Enable user.
e) Manufacturer default is 1-2-3-4-5-6.
2. 8 User Codes (ID 02 to ID 09):
a) Open lock.
b) Change code.
c) No Manufacturer default user codes.
3. Wrong Entry Penalty (Penalty Time)
Entry of four (4) consecutive invalid codes results in a 5-minute penalty time period.
a) The unit beeps at 5 second intervals indicating that it is still in the penalty time
period.
b) While the system is in penalty time, the EntryPad buttons remain unresponsive.
c) While the system is in penalty time, removal of the batteries will interrupt the
penalty time countdown. Upon reinstallation of the batteries, the EntryPad
continues to count down until the 5 minute penalty time period expires.
4. Standby Status
In order to conserve battery power, The system will revert to standby status if there is
Doc.No.: EM1701AC10210303
Version No.: V1.01
SafeLogic C10 D-Drive - Operating Instructions
This manual is for the SafeLogic C10 D-Drive EM-1701A-C10 EntryPad used in conjunction with DL-
1701 D-Drive DeadBolt Lock Body.
In some instances the Manager Code and associated Operating Instructions are not issued
to the End User. In this case, simply remove this insert from the Operating Instruction.

2
no key press in 10 seconds. Standby status is indicated by two short beeps.
5. Automatic Re-lock
The safe lock system automatically relocks after 6 seconds of being opened by a
valid code.
6. Low Battery Alert
a) Repeated beeping (8 beeps) during an unlock operation indicates that the battery
is low and needs immediate replacement.
b) Manufacturer recommends the use of 9-Volt standard alkaline batteries (Duracell
or Energizer brands are recommend) replaced annually.
USER PROGRAMMING INSTRUCTIONS
1. ALWAYS PERFORM OPERATIONS WITH THE SAFE LOCK SYSTEM UNLOCK
AND THE SAFE DOOR OPEN.
2. Before closing the door, make sure all of the program changes are correct.
3. The system will not allow the User Code to be set to six zeros or six nines.
1. To Change Code
a) Enter “0” six times. One beep will sound, indicating that the entry is valid and the
system is awaiting the code change.
b) Next, enter the existing six (6) digit code one time. One beep will sound, which
indicates that the entry is valid.
c) Enter a new six (6) digit code one time. Two beeps will sound, indicating the entry
is valid.
d) Re-enter the new six (6) digit code. One beep will sound, indicating the codes
entered in steps c and d are the same and the code changing process is
successful.
e) If Three beeps sound, the code change process has been unsuccessful. The
existing code is still valid. Repeat steps a to d.
Note:
a) User Code can’t be 000000 or 999999.
b) Verify the new code at least 3 times before closing the door to make sure the
code has been programmed correctly.
c) The system will revert to standby status if there is no key press within 10
seconds. Standby status is indicated by two short beeps.
2. Add User (ID 02 to ID 09)

3
a) Enter the manager code and hold down last digit until one beep sounds,
followed by two beeps.
b) Push “1”. One beep sounds.
c) Enter the ID of the user to be added. For example, enter 2 to add user ID 2. One
beep sounds.
d) Enter a desired six (6) digit code once. One beep sounds.
e) Re-enter the six (6) digit code. One beep sounds, indicating the codes entered
in steps c and d are the same and the user code has been added successfully.
f) If two beeps sound, the process failed. Repeat steps a to d.
Note:
a) User Code can’t be 000000 or 999999.
b) Verify the new code at least 3 times before closing the door to make sure the
code has been programmed correctly.
c) The system will revert to standby status if there is no key press within 10
seconds. Standby status is indicated by two short beeps.
3. Delete User (ID 02 to ID 09)
a) Enter the manager code and hold down last digit until one beep sounds, followed
by two beeps.
b) Push “3”. One beep sounds.
c) Enter the ID of the user to be deleted. For example, enter 2 to delete user ID 2.
One beep sounds.
d) Enter the deleted user code to make sure the code is deleted.
4. Disable User (ID 02 to ID 09)
a) Enter the manager code and hold down last digit until one beep sounds, followed
by two beeps.
b) Push “2”. One beep sounds.
c) Enter the ID of the user to be disabled. For example, enter 2 to disable user ID 2.
One beep sounds.
d) Enter the disabled user code to make sure the code is disabled.
5. Enable User (ID 02 to ID 09)
a) Enter the manager code and hold down last digit until one beep sounds, followed
by two beeps.
b) Push “1”. One beep sounds.
c) Enter the ID of the disabled user to be enabled. For example, enter 2 to enable
user ID 2. One beep sounds.

4
Note:
a) Verify the enabled code at least 3 times before closing the door to make sure the
code has been programmed correctly.
b) The system will revert to standby status if there is no key press within 10
seconds. Standby status is indicated by two short beeps.
6. Open lock with Time Delay
• Super Code programs Time Delay.
a) Enter the user code
b) One beep sounds but lock doesn’t unlock.
c) One beep sounds every ten (10) seconds.
d) Four beeps sound at the end of Time Delay period indicating Time Window
starts.
e) Two beeps sound every ten (10) seconds during Time Window period.
f) Enter code again within Time Window to unlock.
7. Open lock with Dual User Mode
• Super Code programs Dual User or Single User Mode.
a) Enter User code. One beep sounds but lock doesn’t unlock.
b) Enter Manager code to open.
8. Open lock with Dual User Mode with Time Delay
• Super Code programs Dual User or Single User Mode.
• Super Code programs Time Delay.
a) Enter User code. One beep sounds but lock doesn’t unlock.
b) One beep sounds every ten (10) seconds.
c) Four beeps sound at the end of Time Delay period indicating Time Window
starts.
d) Two beeps sound every ten (10) seconds during Time Window period.
e) Enter User code and Manager code within Time Window to unlock.
Specifications
：
Power Supply: DC 9V
Power Supply Range: DC 4.5V-12V
Standby Current : <50μA
Active Current: <20mA
Battery Low Voltage: 5.2±0.2V
Working Temperature: 0℃~ +49℃
Working Humidity (max): <90%

5
Code Length: 6 Digits
Mechanical System Life Span: >100,000 Cycles