Opis 60s cable User manual

1
I
1
2
3
4
5
6
7
890
Manual, Handbuch, mode d’emploi, manual de uso,
manuale d’uso, kullanım kılavuzu
Phone index, Telefonregister, registre téléphonique, agenda
telefónica, registro numeri di telefono, telefon rehberi
ops
technology
&

2
boom, Unterseite, pare inférieure, parte inferior, parte inferiore, taban
SIM card
1
2
3
4

3
ENGLISH
Introducon
Welcome to the 4G version of your Opis Technology desktop mobile, your new retro-
styled mobile phone, resembling a classic xed-line phone. This short manual provides
you with quick start guide, list of special features, and troubleshoong ps.
Quick Start
❶ Assembly
Unpack phone, charger and receiver from the box. Plug the receiver into the boom
of the phone (1). Connect the charger to the back of the phone and plug it into any
standard household A/C power outlet.
❷ Install a SIM card
Slide your SIM card (not included) into the boom of the phone oriented as shown (3).
For simplied operaon, use a card that is not PIN locked (see ⓫)
❸ Switch it on
Slide the main switch on the base from the 0 to the 1 posion as shown in (2). The two
red status lights (network and SIM card) ash alternately for about 30 seconds. The al-
ternate ashing indicates that the phone is busy. Please just wait. Aer some me, all
three status lights should light up briey. (Please note that the baery light will remain
on if the phone is charging.) Aerwards the lights provide informaon on the phone’s
status as described in secon Status lights.
❹ Enter a PIN
This step is only required for a PIN-locked SIM card. Please check the status lights at
the boom of your phone to nd out if this is the case (see secon Status lights). Pick
up the receiver, wait for the busy tone (see secon Receiver Tones) and dial:
Format: <PIN (4 digits)>
Example: if the PIN is 1234: 1234
⇒ if the PIN is accepted the phone rings once.
Note: Aer 3 failed aempts your SIM card will be locked and it is necessary to dial
the PUK and a new PIN:
Format: <PUK (8 digits)>#<new PIN (4 digits)>
Example: if the PUK is 88888888 and the PIN is 1234: 88888888#1234
⇒ if the PIN is accepted the phone rings once.
The phone is now ready for normal operaon. (If a PIN or PUK is not accepted the

4
phone rings twice and you can try again. For details on phone rings see secon Ring
signals.)
❺ Make a call
Pick up the receiver, wait for the dial-tone (see secon Receiver Tones / if you don’t
hear a dial-tone check the Status lights), and dial the number:
Format: <phone number>
Example: if the number is 0123456789: 0123456789
⇒ you will now be connected to the dialled number.
The Opis Technology telephone connects you automacally aer a dial pause of 6
seconds (congurable, see ❿). During this pause, beeps are played in the receiver to
inform you about progress.
Tip: To tell the phone to start a connecon immediately, dial a nal *.
Tip: You can Redial the last number by dialling #/R (PushMeFon mobile only #) instead
of the <phone number>.
❻ Receive a call
Pick up the receiver to accept a call.
Tip: if the receiver is not on the hook, for example because you are taking your Opis
Technology mobile phone with you in a bag, the phone sll rings and you can connect
by replacing the receiver and taking it o again.
Mobile Phone use
Like any other mobile phone, the Opis 60s mobile and Opis PushMeFon mobile con-
tain a baery that needs to be charged before use. To charge, simply plug the charger
into the back of the phone and plug it into any standard household A/C power outlet.
You can check the charge status as described in Status lights below.
Advanced Features
❼ Entering/Changing a local area code
The desktop mobile can save a local area code (to fully emulate xed line phone be-
haviour). To do so, you must rst program that code. Pick up the receiver and dial:
Format: *01#<local area code>*
Example: if the area code is 0351: *01#0351*
⇒ if the local area code is accepted the phone rings once.
From now on it will no longer be necessary to dial the area code for local numbers.
NOTE: This funcon only works where local area codes start with a 0, for example it
doesn’t work in the USA or Canada. Once enabled you can disable the feature again,
simply by dialling *01*.
❽ Using a network short-dial number (eg recharge, mailbox)

5
You can use short-dial numbers within your network by dialling the number followed
by an extra #. Pick up the receiver and dial:
Format: <network short-dial>#
Example: if the GSM network short dial is 2222: 2222#
⇒ you will now be connected to the dialled number.
❾ Quick-dials
The Opis 60s mobile and PushMeFon mobile support entering nine quick dial num-
bers. To program or change a quick dial number, pick up the receiver and dial:
Format: *02#<quick dial number (1-9)>#<number to be dialled>*
Example: if the number is 08154711 and is to be saved as quick dial 2:
*02#2#08154711*
⇒ if the number is accepted the phone rings once.
To use a quick dial number, pick up the receiver and dial:
Format: *<the quick dial number (1-9)>
Example: if you would like to connect to quick dial 2: *2
⇒ you will be connected to the stored number.
❿ Changing the call connecon delay
Normally, the Opis Technology desktop mobile automacally connects a call 6 seconds
aer dialling the last digit. This delay can be changed in 2 second increments as fol-
lows. Pick up the receiver and dial:
Format: *03#<(1-9)>* (1 x 2 seconds to 9 x 2 seconds delay).
Example: if you would like to set the connecon delay to 4 seconds (2x2 sec
onds = 4 seconds): *03#2*
⇒ if the new dial delay is accepted, the phone rings once.
⓫ Disabling/Enabling the SIM card PIN lock
You can disable (recommended) or enable your SIM card PIN lock. Pick up the receiver
and dial:
Format: *04#<0-1>#<PIN>* (0= lock disabled, 1= lock enabled)
Example: if your PIN is 1234 and you would like disable the PIN lock:
*04#0#1234*
⇒ if the PIN lock seng is accepted the phone rings once.
If the seng is not accepted the phone rings twice and you can try again.
⓬ Disabling/Enabling Roaming lock
You can enable or disable (default) the roaming lock. When the roaming lock is acve,
the telephone can only connect to the home network. Pick up the receiver and dial: