Opticon CS1504 User manual

Version REV-00
Barcode scanner CS1504 / OPN2001
Installation and handling
1
PopScan® is a technology of Sensational AG.
Index
Install driver . . . . . . . . . . . . . . . . . . . 2
Connect scanner . . . . . . . . . . . . . . . . . 3
CS1504 serial cable . . . . . . . . . . . . . 3
CS1504 USB connection . . . . . . . . . . . . 3
OPN2001 USB connection . . . . . . . . . . . 3
Read scanner . . . . . . . . . . . . . . . . . . 4
Scanner CS1504 . . . . . . . . . . . . . . . . . 5
Handling . . . . . . . . . . . . . . . . . 5
Functions . . . . . . . . . . . . . . . . . 6
Change batteries . . . . . . . . . . . . . . 7
Disposal of device . . . . . . . . . . . . . . 7
Problem solving . . . . . . . . . . . . . . . 8
Technical Data . . . . . . . . . . . . . . . 8
Scanner OPN2001 . . . . . . . . . . . . . . . . 9
Handling . . . . . . . . . . . . . . . . . 9
Functions . . . . . . . . . . . . . . . . .10
Problem solving . . . . . . . . . . . . . . .11
Meaning of LCD-Display . . . . . . . . . . . .11
Quantity chart . . . . . . . . . . . . . . . . . . 12

Version REV-00
Install driver
To allow communication between the scanner an
your PC respectively the PopScan web applicati-
on, please run the installation program.
This installation program is availabe on the web
application (see "help").
Download installation program from the web application.1.
Click "allow", if eventual warnings occur.
(To start the installation you have to be logged in as admi-
nistrator on your PC)
The installation program starts..2.
Proceed with "continue".
Click "Install" to start with the installation.3.
Click "complete" to nish the installation.4.
2
2.
3.
4.

Version REV-00
Connect scanner
Connect your scanner to the PC. You can choose
between USB connection and serial connection.
CS1504 serial connection
Connect serial cable with PC.1.
CS1504 USB connection
Connect USB Adapter with PC1.
Advice: Keep the USB Adapter plugged in to avooid
problems reading the scanner.
Connect serial cable with USB Adapter.2.
OPN2001 USB connection
connect USB cable with PC.1.
3
1.
1.
2.
1.

Version REV-00
Read scanner
Your scanner is ready. Test now, if the scanner is
working properly and if you can log in to the web
application.
Ensure that the scanner is connected to the PC1.
Load the starting page of your web application in the2.
browser (Internet Explorer, Firefox, ...) an click on the
scanner-icon to rad the scanner.
The reading window loads. For the rst time, this process3.
can take several minutes.
After a successful search, the scanner connection appears4.
automatically, e.g. COM4
Click "read" , to log into the web application via scanner.5.
Please note: problems due to firewalls
and other restrictions
If you are using a rewall, please consider the following
settings::
Make sure you have java applets and pop-ups allowed
The java applet sends data via HTTP-POST to the web-
site (in most cases the browser communication already
allows this).
If you are working with a professionally hosted network,
please contact your administrator to make these modi-
cations..
4
3.
5.
4.

Version REV-00
Scanner CS1504
Handling
The compact scanner offers the practical possi-
bility to scan articles via barcode and saves more
than 300 items.
plus buttona)
minus buttonb)
LED displayc)
USB connectiond)
5
Hint
Point the scanner at the code and ensure the red beam
covers the whole barcode and is in square with the bars.
Warning! Laser Class 1
Don’t aim a laser pointer towards a person’s head. This
is to prevent the beam from getting in their eyes, possib-
ly causing eye damage.
a
b
c
d

Version REV-00
Functions
Your scanner maintains an article list in its sto-
rage and remembers each product and amount
(amount by default = 1)
Add product
Scan article with plus button.
(another scan increases the amount by one)
Add product with amount
Scan article with plus button,
then scan amount from the quantity chart.
(nd quantity chart in the appendix of this documentation)
Reduce amount by one
Scan article with minus button.
Delete single article
Scan article with minus button for six seconds.
Delete all articles
Push minus button for ten seconds without scanning anything.
Sound on / off
Push plus button for ten seconds without scanning anything.
(We recommend leave Sound on)
6
6s
10s
10s
+
+
+
+
+
+
+

Version REV-00
Change batteries
If LED is red during scanning, the batteries are
dead soon. Please change batteries.
Recommended manufacturers and types:
- Energizer EPX 76
- Energizer 357
- Maxwell SR 44W
- Rayovac 357
Undo screw on bottom.1.
Open battery compartment.2.
Remove old batteries.3.
Insert 4 new batteries. Please pay attention to polarity4.
(+/-).
Close5. battery compartment and tighten screw.
Disposal of device
The scanner has to be returned to Motorola.
Please nd information and return adress under:
www.symbol.com/environmental_compliance
7

Version REV-00
problem solving
technical data
8
problem possible cause suggested solution
scanner doesn't work batteries is inserted
the wrong way
insert batteries again.
pay attention if plus and minus is correct
(instruction placed in lid)
batteries are dead replace batteries
scanner is broken send in scanner to your supplier
scanner can't scan or
delete barcode
barcode is defective test scanner on other barcode
distance or ankle
doesn't t
place beam vertically on barcode and modify the
distance
scanner is connected
to PC
if the scanner is connected to PC, no codes can be
scanned. Unplug scanner to gather data.
memory is full if more than 150 articles are scanned, data has to be
transferred to the PC or deleted
PC doesn't recognize
scanner
cable unplugged check if cable and adaptor is connected properly to
PC
PopScan-driver not
properly installed
install the driver again
LED ashes red batteries are dead replace batteries
LED ashes red, green
and orange
scanner is broken send in scanner to your supplier
speification information
supported barcode formats UPC/EAN, Code 3 von 9, Code 128, D 2 von 5,
Coupon-Code
memory capacity 150 barcodes (30 characters per code)
compatible battery types Energizer EPX 76*
Energizer 357*
Maxell SR 44 W
Rayovac 357
* recommended by Symbol
battery capacity approx. 5000 scans with fresh batteries
working temperature 5°C to 40°C
max. humidity 95%
weight 80 g (with batteries)
storage temperature -20°C to 60°C

Version REV-00
Scanner OPN2001
Handling
This device enables storage and removal of
barcode scans. The collected barcodes can be
transmitted by a USB cable. The integrated batte-
ry recharges automatically when you connect the
scanner to a computer. It has memory space for
5’000 barcodes. Using the OPN2001 is very easy:
users only need to press a trigger key to operate
and a reset key to control mistakes.
plus buttona)
minus buttonb)
LED displayc)
USB connectiond)
a
b
c
d
9
Hint
Point the scanner at the code and ensure the red beam
covers the whole barcode and is in square with the bars.
Warning! Laser Class 1
Don’t aim a laser pointer towards a person’s head. This
is to prevent the beam from getting in their eyes, possib-
ly causing eye damage.

Version REV-00
Functions
Your scanner maintains an article list in its sto-
rage and remembers each product and amount
(amount by default = 1)
Add product
Scan article with plus button.
(another scan increases the amount by one)
Add product with amount
Scan article with plus button,
then scan amount from the quantity chart.
(nd quantity chart in the appendix of this documentation)
Reduce amount by one
Scan article with minus button.
Delete single article
Scan article with minus button for six seconds.
Delete all articles
Push minus button for ten seconds without scanning anything.
Sound on / off
Push plus button for ten seconds without scanning anything.
(We recommend leave Sound on)
10
6s
10s
10s
+
+
+
+
+
+
+