OPTO 22 groov EPIC Manual

OPTO 22 • 800-321-6786 • 1-951-695-3000 • www.opto22.com • [e-mail]
© 2019-2020 Opto 22. All rights reserved. Dimensions and specifications are subject to change. Brand or product names used herein are trademarks or registered trademarks of their respective companies or organizations.
OPTO 22 • 800-321-6786 • 1-951-695-3000 • www.opto22.com • [e-mail]
© 2019-2020 Opto 22. All rights reserved. Dimensions and specifications are subject to change. Brand or product names used herein are trademarks or registered trademarks of their respective companies or organizations.
PAGE 3
Form 2311-201202
groov EPIC Learning Center Setup
groov EPIC Learning Center Setup Form 2311-201202
PAGE 2
ASSEMBLING THE LEARNING CENTER
1. Let’s start by adjusting the handle/kickstand in the back.
a. After you remove the Learning Center from the box, place it on a stable surface,
upside down, with the top edge of the unit and the acrylic stand sitting on the
surface. Do not place the Learning Center with the touchscreen laying flat on
the surface. You may damage the touchscreen.
b. With the back of the unit facing you, locate the pin on one side of the handle,
near the acrylic surface. Hook your finger into the ring and pull out the pin.
c. Adjust the handle to align the holes to the desired position, then insert the pin.
– Position 1: Orients the Learning Center so that it’s easier to see while sitting
at your desk.
– Position 2: Orients the Learning Center so that it’s easier for an audience to see it.
2. Grab the Learning Center with both hands and turn it right-side up, so that the bottom edge of the acrylic stand and the kickstand sit on the
surface.
3. Connect an Ethernet cable and the temperature probe.
a. Lift the touchscreen. Connect an
Ethernet cable (that’s connected
to your network) to the ETH0
network interface, which is the
top interface of the two
interfaces located on the
underside of the groov EPIC
processor.
b. Connect the temperature probe
to the temperature probe
connector on the acrylic stand.
4. Turn the Learning Center around so you can see the back.
a. Connect the DC connector end of the power cord to the DC socket.
b. Connect the power cord to the adapter.
c. Connect the power adapter to the outlet of 110 to 240 VAC power.
5. You can illuminate the Learning Center with three different
light settings:
– To provide a steady blue illumination, set the switch to the
top position.
– To turn off the light, set the switch to the middle position.
– To be able to program the illumination, set the switch to
the bottom position.
6. Turn the Learning Center around so you can see the front. Turn
on the processor and close the touchscreen.
INITIALIZING THE LEARNING CENTER
1. When the touchscreen displays the Welcome! screen, make a note of the value in the Hostname or Eth0 IP Address box.
2. Open a web browser on your computer and type in the following as the URL, entering the Hostname (or Eth0 IP address) from the previous step
in place of <hostname>: https://<hostname>
For example: https://opto-03-fa-bf or https://xxx.xxx.x.xxx, where xxx.xxx.x.xxx is the IP address shown in the
Eth0 IP Address field.
3. If your browser displays a warning about security, you can accept the warning and proceed to connecting to the processor.
4. Click Let’s get started!
5. In the Create an Account screen, type in the username and password that follows strong security recommendations. This username and
password is the first administrator level user for your Learning Center. Remember it! groov EPIC does not provide a way to recover a lost
password or username. Click Create Account.
6. We recommend that you check that the version of groov EPIC processor firmware running on the Learning Center is the latest version. Click
Configure Device > Info and Help > About.
7. Write down the Restore Version: ____________________________________
8. Open the black envelope and pull out the GRV-EPIC-PR1 Activation Certificate. Follow the instructions on the certificate to activate your groov
EPIC processor. When you reach the profile page for your groov EPIC processor, under the Latest Releases section, note the version number for the
groov EPIC Field Update. Compare this version number with the Restore Version number you noted in step 7 above:
– If the version number for the groov EPIC Field Update is the same as or lower than the Restore Version number, then you have the latest
firmware installed on your processor! You can skip the rest of this step.
– If the version number for the groov EPIC Field Update is higher than the Restore Version number, you’ll need to download and install the
newer version of the firmware that’s on the webiste. Follow the instructions in “Updating Firmware on a groov EPIC Unit”in the groov EPIC
User’s Guide (form 2267). You can skip step 5 (creating a backup of your unit) and step 6 (deactivating the Ignition Edge license).
Your groov EPIC Learning Center is now up and running!
To learn how to program and manage your groov EPIC Learning Center, see our online training by visiting training.opto22.com, selecting groov EPIC
Training Series, and enjoy exploring your Learning Center! If you are interested classroom training, you can learn more by visiting our website
(www.opto22.com) and looking up GROOV-TRAINING-PF.
Example Values for your Learning Center
Hostname:
______________________________________
Eth0 IP Address:
_______________________________________
Step 6.
Step 5.
Steady blue
Off
Programmable
Step a.
Step b.
Step c.
Step b.
Step c.
Position 1
Position 2
Step a
Step b
Step a (enlarged)

OPTO 22 • 800-321-6786 • 1-951-695-3000 • www.opto22.com • [e-mail]
© 2019-2020 Opto 22. All rights reserved. Dimensions and specifications are subject to change. Brand or product names used herein are trademarks or registered trademarks of their respective companies or organizations.
OPTO 22 • 800-321-6786 • 1-951-695-3000 • www.opto22.com • [e-mail]
© 2019-2020 Opto 22. All rights reserved. Dimensions and specifications are subject to change. Brand or product names used herein are trademarks or registered trademarks of their respective companies or organizations.
PAGE 4
Form 2311-201202
groov EPIC Learning Center Setup
PAGE 1
groov EPIC Learning Center Setup Form 2311-201202
INSTALLING CONTROL PROGRAMMING SOFTWARE
If you want to create and run CODESYS applications:
1. Go to the CODESYS Store website (store.codesys.com) and download the CODESYS Development System, Version 3.5.13.1 or higher.
2. Install CODESYS Development System, following the instructions on the screen for a typical installation.
3. Go to the Opto 22 website (www.opto22.com) and enter “CODESYS”in the search box. Select Opto 22 Library Package for CODESYS
Development System from the list of suggested search terms.
4. On the Opto 22 Library Package for CODESYS Development System page, click Download and save the file on your computer. The file that you
download ends in .package .
5. Follow the instructions in the groov EPIC User’s Guide (form 2267) to add your groov EPIC processor to the CODESYS Development System.
If you want to create and run a PAC Control strategy:
1. Go to the Opto 22 website (www.opto22.com) and enter “PAC Project Basic”in the search box. Select PAC Project Basic from the list of suggested
search terms.
2. On the PAC Project Basic page, click Download and save the file on your computer. The file that you download ends in .exe .
3. Double-click the *.exe file that you downloaded and follow the instructions on screen for a typical installation.
4. Follow the instructions in the PAC Control User’s Guide (form 1701) to add your groov EPIC processor as a control engine to your PAC Control
program.
DOWNLOADING PROJECT FILES
The online training modules will take you through the creation of several projects. If you are interested in reviewing completed project files, you can
download them from the Opto 22 website:
1. Go to the Opto 22 website (www.opto22.com) and enter “EPIC Learning Center”in the search box. Select groov EPIC Learning Center Package
from the list of suggested search terms.
2. On the groov EPIC Learning Center Package page, click Download and save the file on your computer.
3. Navigate to the folder where you stored the file and uncompress it.
4. Follow the instructions in the Learning Center Package Installation Technical Note (form 2315) to install these files on to your Learning Center.
As you go through the online training and review the projects, the following table can help you understand how the load panel is mapped to the
modules.
WELCOME!
Before you begin, check that you received all the following items in your package:
The following hardware is mounted on the acrylic stand:
You’ll also need the following:
•An Ethernet cable.
•110 to 240 VAC power.
•A username and password that follows strong security recommendations.
•A network to connect the Learning Center and a computer or mobile device that can connect to the same network as the Learning Center.
Note: To preserve the clean look of the acrylic stand, remove any fingerprint stains with a plastic cleaner (for example, Plexus® plastic cleaner), not a
glass cleaner.
How do I get my certificates for Premium Factory Training?
The purchase of a Learning Center includes two certificates to attend groov EPIC Premium Factory Training for FREE. If your certificates are not in your package, contact
Opto 22 at [email protected] or 800-321-6786 for instructions on obtaining these certificates.
I/O Mapping
Digital Inputs (GRV-IACDCTTL-24) Digital Outputs (GRV-ODCI-12) Analog Input (GRV-IICTD-12)
Ch 0: Top pushbutton, latching Ch 0: Blue LED ring around bottom pushbutton Ch 0: ICTD
Ch 1: Bottom pushbutton, momentary Ch 1: Sonalert Alarm
Ch 6: Light rain status (from DO Ch 3) Ch 2: Resistor in ICTD probe Analog Input (GRV-IV-24)
Ch 8: Light rain status (from DO Ch 4) Ch 3: Light rain Ch 0: Potentiometer
Ch 10: Light rain status (from DO Ch 5) Ch 4: Light rain
Ch 12: Light rain status (from DO Ch 6) Ch 5: Light rain
Ch 6: Light rain
Ch 7: Backlight, Red
Ch 8: Backlight, Green
Ch 9: Backlight, Blue
Ch 10: Python Output, software driven
Ch 11: Node-RED output, software driven
•GRV-EPIC-PR1 (groov EPIC processor) •Module 0, GRV-IACDCTTL-24 •Module 2, GRV-IICTD-12
•GRV-EPIC-PSPT (pass-thru power adapter) •Module 1, GRV-ODCI-12 •Module 3, GRV-IV-24
•GRV-EPIC-CHS4 (4-module mounting chassis)
•Load Panel: 1 Multi-color LED strip backlight (red, blue, and green); 2 illuminated pushbuttons; 1 potentiometer; 1 temperature probe connector;
1 Sonalert alarm
groov EPIC I/O unit mounted on an acrylic stand
ICTD Temperature probe with resistor
12V Power adapter & cord
Two documents:
•groov EPIC Learning Center Setup
(this document; form 2311)
• A black envelope with a
GRV-EPIC-PR1 Activation Certificate
Pelican carry case