Optoma Panoview GrayWolf II DF-GWII9106F User manual

Professional Cinema
Fixed Frame Screen
Set-up Guide

2 | Fixed-Frame Set-Up Guide
Product Content
The following items are included with your fixed framescreen.
Verify all items are present and prepare a clean working environment
to begin assembly.
Part Description Quantity
#1 Frame (Long Bar) 2
#2 Frame (Short Bar) 2
#3 Screen (Glass Beeded) 1
#4 Screen Rod (Long Rod) 2
#5 Screen Rod (Short Rod) 2
#6 Frame Edge Protector (Long) 2
#7 Frame Edge Protector (Short) 2
#8 Hanging Plate 2
#9 Locking Screws 12+2
#10 Spring Hook 12+2
#11 Elbow Connectors 4
#12 M6*20 with Bolt and Screw 6
#13 M4*12 Screw 16

Fixed-Frame Set-Up Guide | 3
Part #2
Part #1
Fixed-Frame Screen Set-up Instruction
Precaution:
1) Attempt to assemble the fixed frame screen in a clean environment.
2) Professional mounting techniques should be observed. Manufacturer
cannot be liable for substandard/faulty installations.
Layout the frame (the long and short bars).
Parts Used: Frame (Part #1&2)
Insert the spring hook on one horizontal & vertical
side into the screen frame as shown below. (Long
side 7 hooks,short side 5 hooks)
Parts Used: Spring Hook (Part #10)

4 | Fixed-Frame Set-Up Guide
Left Right
Bolts
Insert the locking screws on one horizontal and
vertical side into the screen frame as shown
below. (Long side:7 locking screws,short side: 5
locking screws)
Parts used: Locking Screws (part #9)
Insert bolts of M6*20 screw into the screen frame
as shown below
Parts used: M6*20 nuts (part #13)

Fixed-Frame Set-Up Guide | 5
Left Right
Elbow connector
Insert the elbow connectors into the open ends of
the frame to connect the sides together.
Parts used: Elbow connectors (part #4), frame

6 | Fixed-Frame Set-Up Guide
With the four sides of the frame connected, insert
four M4*12 screws to each corner of the screen as
allowed
Parts used: M4*12 screws (part #12), elbow
connectors, frame
Un-roll the glass beaded screen, with the viewing
side down
Parts used: Screen (part #3)

Fixed-Frame Set-Up Guide | 7
Fig 8-A
Thread the long rod into the horizontal edge of the
screen. Then thread the short rod into the vertical
edge of the screen.
Parts used: Screen rod (part #4/5), screen
With the rod threaded screen, connect the spring
hooks (Fig. 8-A) to each of the openings of one
horizontal side and one vertical side.
Parts used: spring hook, screen rod,screen

8 | Fixed-Frame Set-Up Guide
Fig 8-B
Fig 8-C
Connect the locking screw (Fig.8-B) to each of the
openings of one horizontal side and one vertical
side.
Parts used: Locking screws, screen, screen rod
Tighten locking screw with Philip screw driver
(Fig. 8-C)
Parts used: Philip Screw Driver

Fixed-Frame Set-Up Guide | 9
Install the frame edge protector to the frame as
shown below.
Parts used: Frame edge protector (part #6/7).
Install screen hangers on to the top corners of the
frame. Using M6*20 screw and bolt.
Parts used: Hanging plate (part #8), M6*20 Screw
(part #13)

Optoma Technology, Inc.
715 Sycamore Drive, Milpitas CA 95035
Tel: [phone] • Fax:[phone]
For more information, please visit www.Optoma.com.
Specifications subject to change without notice. Copyright 2006 Optoma Technology, Inc.
USA
715 Sycamore Drive
Milpitas, CA 95035, USA
Tel: [phone]
Fax: [phone]
www.optomausa.com
5630 Kennedy Road
Mississauga, ON, L4Z 2A9, Canada
Tel: [phone]
Fax: [phone]
www.optoma.com
Canada