OR STEEL light TALOS User manual

TECHNICAL MANUAL
The small submersible LED spotlight is the ideal product to enhance your swimming
pool or other aquatic areas, whether fresh or salt water. It is equipped with a high power
LED which enables it to provide excellent light diusion in a sub-marine environment.
Manufactured in 316L stainless steel, it is completely watertight.
TALOS
RGBW/DYNAMIC WHITE 700mA
POWER 4x10W
SUPPLY 700mA
POWER
SUPPLY
Not included
WIRING Serial
Electrical features
TECHNICAL SHEMATICS
DIMENSIONS Ø150x59mm
WEIGHT 2.9kg
MATERIAL 316L Stainless steel
OPERATING
TEMPERATURE
- 20°c ~+ 60°
PROTECTION RAITING IP69
RESISTANCE INDEX IK10
APPLICANCE CLASS CLASS III
WALKOVER FIXTURE NO
DRIVE-OVER FIXTURE NO
Mechanical features
INSTALLATION SHEMATICS
General features
POWER SUPPLY
CABLES
Supply wire 8x0.22
mm2 in IP68
PHOTOBIOLOGICAL
SAFETY
Risk group I
ENERGY CLASS A /A+/A++
All data are given for information purposes only. They do not constitute a contractual commitment on our part and are subject
to change at any time.
150
150
55
59
75
T° max 55°C
AA+
A++
ACS
IK10
IP69
2,9
AVERAGE LIFE OF THE
LED
60 000 hours
Certicated L90 B10
COLOR EMISSION RGBW :
Red - Green - Blue -
4000°K
Dynamic white :
2700°K - 3000°K
4000°K - 6000°K
BEAM 10°-25°-40-115°
INITIAL OUTFLOW 1757lm at 4000k
Features
lighting technology
12
3
max 5mm
125
143
123
104
24,5
Sealing Casing
max 5mm
Serial wiring RGBW
Concrete
Concrete
Concrete
Flexible ref TA802
Fourreau
Wire ref CAB0010
Concrete
Sealing casing
Concrete
Connect to the ground
Sealing casing
Mortar
Tile
Water level
Water level
Water level
Sealing casing
to the edge of
the mortar
Tighten the
cable gland

1. Function
Submersible recessed spotlight for occasional use and lighting small underwater
areas. Illuminates steps, small pools, waterfalls or a marine environment. Only
an IP69 connection to the electricity network ensures the IP69 degree of the
product.
Spotlight for permanent submersion only. Construction/special Functions
available on request. Please note that during installation in water, the intensity
depends on the turbidity of the water.
2. Technical data/Assembly
Spotlight in 316L INOX electro-polished - 4x 10W LED - Color emission : RGBW/W.
316L stainless steel gland. Delivered with 8x0.22 mm² Submersible cable. Sealing
casing to be ordered separately.
3. Installation/Assembly
Please comply with the applicable national safety requirements. We disclaim
all responsibility for non-compliant use or assembly. Similarly, we reject any
responsibility for any modifications to the light fittings. When in use, constant
current spotlights must always be connected in series to the corresponding DC
power supply (see power packs) (700 mA). Do not disassemble the spotlight
casing, because the cables and the plate are sealed. Exterior and underwater
assembly can be carried out on different media. Mount the projector directly on
concrete, paving blocks, plates, wood and in association with an earth rod (Pt800)
We cannot supply universal installation instructions because ground conditions
and the location will vary for each project. The pictograms show examples of
typical installations A/B /C Surface mount the projector on a strengthened
support and on a support with an earth rod and on a weighted support. If800).
Caution: Never use full power withou t water Caution: Do not use a high pressure
cleaner. Caution: Protect the spotlights from frost; where appropriate, dismantle
or ensure special protection. Any lost screws should only be replaced by V4A
stainless steel screws. According to conditions of use (power, environmental
circumstances), it is recommended to change the seals (on the glass, screw
fittings and O-rings) and the cable every 5 to 8 years.
4. Connecting to the power packs/connection matrix
Constant current spotlights must only be connected in series. H/I. If applicable,
proceed with connection in series in separate load distribution units, the outside
of which must also be protected against humidity using a sealing compound.
5. General Maintenance Instructions
When cleaning the spotlight, do not use detergents which are harmful to metals.
The use of hydrochloric acid-based detergents on and around any parts of a
stainless steel light fitting is totally prohibited. Regularly clean the spotlight and
its mounting box to avoid any rust deposit Be careful never to switch on at full
power without water
6.Warranty conditions
The following time limits and provisions of the warranty shall apply from the date
of delivery: - 24 months for Orsteel spotlights
•The warranty covers defects in materials, construction defects and any
treatment proven to be attributable to the manufacturer.
•Any damage resulting from the non-compliance with this user leaflet or any
non-compliant repair is excluded from the warranty.
•We disclaim any guarantee where the installation has not been carried out
according to the instructions or where unsuitable bulbs or connection cables have
been used.
•We reserve the right to make any modification corresponding to technical
development.
7. Important Notes (The warranty becomes void in the event of non-compliance
with the following points)
The absence of damage caused during transport must be verified before
installation! All assembling and installation, as well as any electrical work, must
be carried out by qualified personnel. should be used ! The cable length for lamps
must be chosen to avoid extending it in water or in a wet environment. Any
subsequent claim for this reason will not be accepted. A mounting distance of
10 cm between each device is strongly recommended to avoid mutual heating.
Equipment must not be connected to the electricity supply during installation,
otherwise surges in the power supply could damage the LEDS. There must be
no primary voltage when changing LEDS. When connecting the lamps, please
ensure the polarity matches! A polarity error may damage the LED module.
The installation of a protection against any over voltage by the customer
compliant with standards DIN VDE 0100-443, DIN VDE 0100-534 and In 62305
is recommended. Please observe the measures against electrostatic discharge
during all work on the spotlights, equipment and LED.
INSTALLATION MANUAL