Orbit baby Double Stroller Kit User manual

ⒸⒶⒷⒺ

ⒻⒽⒹⒾ
ⓁⓂⓃⓄⓅⓇⓆⓊⓉⓈⓀⒿ

02
03
05
01
04
‘CLICK’
06
‘CLICK’

Double Stroller Kit
®
®

2 – ENGLISH – Manual Text Booklet – Orbit Baby Double Stroller Kit

Manual Text Booklet – Orbit Baby Double Stroller Kit – ENGLISH – 3
Important: Read these instructions carefully before use and keep them for future
reference. Your children's safety may be affected if you do not follow these instructions.
The Orbit Baby Double Stroller Kit is made up of seven parts, the Rear SmartHub Attachment,
the Stroller Unibar, two stroller frame leg connectors, two sets of stroller rear wheel disks,
and a ShadePad. (*This product does not include G3 Stroller Base.)
*
Using this Instruction Manual:
Each step is described in both text in this booklet, and illustrations in the manual foldout. Numbers like
󱫁in this booklet refer to the related sections in the manual foldout. Boxes like 󱪼in this booklet refer
to individual steps illustrated in sections of the manual foldout.
Letters like Ⓐrefer to the product parts identified on the labeled illustrations located both in this
booklet and in the manual foldout.
The Orbit Baby Double Stroller Kit CANNOT BE USED with G1, G2 or O2
Stroller Bases.
ShadePad
Stroller Unibar
Rear SmartHub Attachment
stroller rear wheel disks
stroller frame leg connectors

4 – ENGLISH – Manual Text Booklet – Orbit Baby Double Stroller Kit
ShadePad™ ⒶPhilips screws Ⓑfold lock Ⓓ
front SmartHub™ ⒺⒻ wheel release
button
Ⓖ swivel lock
twist grip Ⓒ Ⓗ Unibar
Ⓚ release lever
Ⓛ curb step
Ⓜ rear SmartHub™
Ⓞ Double Stroller
Kit SmartHub
attachment wheels
Ⓝ wheel release
button
Ⓡ tie rod bolt Ⓢ brake pedals
Ⓠ stroller frame
leg connectors
Ⓟ rear leg
Ⓤ wheel disk (2x)
Ⓣ wheel disk cap
(2x)
Ⓙwater
bottle tray
ⒾUnibar
levers
This product does not include G3 Stroller Base.

Manual Text Booklet – Orbit Baby Double Stroller Kit – ENGLISH – 5
⚠ WARNING ⚠
FAILURE TO FOLLOW THESE WARNINGS AND THE INSTRUCTIONS COULD RESULT IN
SERIOUS INJURY OR DEATH
◦ Do not let others use the Orbit Baby Double Stroller Kit or other connected Orbit Baby
products unless they understand how to properly use them.
◦ Do not use the stroller if any parts are damaged, broken or missing. If the instruction
manual is missing or you need replacement parts or assistance, see the contact
information included with this manual.
◦ Read the G3 Stroller Base and G3 Stroller Seat Instruction Manuals.
PREVENT SERIOUS INJURY OR DEATH
◦ NEVER leave your child unattended.
◦ Always provide the supervision necessary for the continued safety of your child.
◦ Stroller must be fully erected and locked in position prior to use.
◦Maximum child weight for the seat on the front SmartHub is 50 lbs (23 kg) with the G3
Stroller Base. Maximum child weight for the seat on the rear SmartHub is 40lbs (18 kg).
Maximum child height for the seat on the rear SmartHub is 34 in (86 cm). Note that 34 in
(86 cm) is a reduced height limit for the stroller seat when using it on the rear SmartHub.
◦Never use the ANY ORBIT BABY TODDLER CAR SEAT on the REAR SmartHub. Use any
Orbit Baby Toddler Car Seat (G1, G2 or G3) on the front SmartHub only.
◦ Use caution when pushing stroller near traffic or in highly congested areas.
FALL HAZARD: Avoid serious injury from falls or tipover.
◦ Always make sure the Double Stroller Kit SmartHub Attachment is securely locked into the
stroller frame leg connectors before placing your child into the stroller or starting to stroll.
Pull backwards on the Double Stroller Kit SmartHub Attachment and check that the red
triangles on both sides are NOT visible.
◦Adult control required. Do not allow your child to stand on, sit on or play with the Double
Stroller Kit SmartHub Attachment. It is not a toy.
◦Never let your child climb into or out of a seat unassisted. ◦Always make sure the stroller seat, infant car seat or bassinet on the Double Stroller Kit
SmartHub Attachment is locked in the forward-facing position before strolling. Side-facing
locked positions are for stationary use only. Refer to Stroller Seat instruction manual for
more information.
Ⓜ Ⓞ

6 – ENGLISH – Manual Text Booklet – Orbit Baby Double Stroller Kit
⚠ WARNING ⚠
FALL HAZARD: Avoid serious injury from falls or tipover.
◦ DO NOT USE ANY SEAT ON REAR SMARTHUB IN REAR FACING POSITION.
◦ DO NOT use stroller seats on the front and rear SmartHubs facing each other in fully
reclined position.
◦ DO NOT use any Toddler Car Seat on the rear SmartHub.
◦ ONLY USE Stroller Seat, Infant Car Seat, Toddler Car Seat, and Bassinet in side facing
position when stationary.
◦ Always remove or adjust the frontmost seat and always rotate the rear seat to the side
before removing the rear seat from the rear SmartHub Attachment to avoid loss of control
and the seat from being dropped.
◦DO NOT use stroller on stairs or escalators with children in it.
◦DO NOT lift or carry stroller by the water bottle tray or Double Stroller Kit SmartHub
Attachment.
◦ Use caution when maneuvering curbs and irregular surfaces. Use curb breaks whenever
possible. If one is not available, move over the curb slowly with the stroller perpendicular to
the curb. To lift the stroller onto the curb, pull back on the handlebar and push forward with
one foot on the Double Stroller Kit Attachment curb step to lift the stroller onto the curb. Do
not allow the stroller to drop off the curb.
◦ Do not place parcels or accessory items in the stroller unless made by or specifically approved
by Orbit Baby. Added parcels or accessory items can make the the stroller become unstable.
◦ Do not place more than 1 lb (0.5 kg) in the water bottle tray. Excessive weight may cause a
hazardous unstable condition to exist.
◦ Do not place more than 1.5 lb (0.7 kg) in the ShadePad. Excessive weight may cause a
hazardous unstable condition to exist.
AVOID BURN INJURY:
◦Never use the water bottle tray to hold hot liquids. These liquids may splash and spill onto
you or your children and cause injury.
AVOID LOSS OF CONTROL OF THE STROLLER:
◦ Always lock the front wheels when pushing the stroller on uneven terrain.

Manual Text Booklet – Orbit Baby Double Stroller Kit – ENGLISH – 7
◦ Use caution when pushing stroller on uneven terrain or hills.
◦Always lock the parking brake when the stroller is stopped.
◦ NEVER leave the stroller unattended on a hill or incline even when the stroller brake is
locked.
⚠ WARNING ⚠AVOID PINCH INJURY:
◦Keep fingers clear of stroller when folding and unfolding the stroller.
◦Keep your children's hands and fingers clear of moving parts when adjusting the stroller
seat or Unibar.
◦Keep your children's arms, legs and feet clear when rotating seats and adjustng seat
recline.
Getting Started
Remove all the parts from the box. You should have received a Double Stroller Kit SmartHub
Attachment, two (2) Double Stroller Kit SmartHub Attachment wheels, a Unibar, two (2) stroller frame
leg connectors, a set of stroller rear wheel disks, and a ShadePad. These parts are illustrated in your
manual foldout. Note that the fasteners needed for installation are loosely screwed into the various
parts to help you keep track of where they go. You will need to remove these fasteners before
installing each part.
󱫁 Removing your old handlebars
󱪼Start with your stroller frame open and erect. Completely unscrew both Philip screws Ⓑunder
the Orbit Baby G3 Stroller water bottle tray.
󱪼Remove the old water bottle tray by pulling up firmly.
󱪼Remove the screw on the other side in the same manner. Push down on the left handlebar button
and pull up on the handlebar to remove it from the stroller frame. Repeat with right handlebar.

8 – ENGLISH – Manual Text Booklet – Orbit Baby Double Stroller Kit
󱫃 Installing your new Unibar
⚠ WARNING ⚠
◦ Proper assembly is required. Check that Unibar is properly installed and screws are tight.
󱪼Remove the two loose Phillips screws from the metal clamps in the bottom of the Unibar assembly;
keep them handy. Lock the brakes by pressing firmly down on the right brake pedal Ⓢwith your
foot. Install the new Unibar assembly by aligning the water bottle tray Ⓙto the exposed aluminum
handlebar tubes and pushing evenly on both sides in short, hard bursts. Push the water bottle tray
down until it completely covers the square cross tube with screw holes completly visible below
cross tube.
󱪼Completely tighten both thumbscrews into the metal inserts in the water bottle tray. Re-install the
two Phillips screws you removed from the metal clamps in the water bottle tray. Tighten the screws
completely using a Phillips screwdriver.
󱫅Installing your wheel disks
⚠ WARNING ⚠
◦ Proper assembly is required. Check that wheel disks are properly installed and fasteners are
tight. Shake rear wheels after installation to ensure neither the disk nor the cap move or rattle.
󱪼Remove both rear wheels from the stroller frame by pulling down on the bent metal tab behind
the wheel and pulling the wheel outwards. Remove the three Phillips screws that are loosely
fastened into the wheel disk using a Phillips screwdriver tool. Insert a wheel disk Ⓤ into the inside
of each wheel, lining up the spokes and slots in the wheel disk. Insert the wheel disk cap Ⓣon the
outside of each wheel lining up the screw holes with the bosses on the wheel disk. Using a Phillips
screwdriver tool, fully tighten the three mounting screws to secure the wheel disks and caps to the
rear wheels. Check your installation by shaking the rear wheel and ensuring neither the disk nor the
cap move or rattle.

Manual Text Booklet – Orbit Baby Double Stroller Kit – ENGLISH – 9
󱫇 Attaching the stroller frame leg connectors
⚠ WARNING ⚠
◦ Proper assembly is required. Check that leg connectors are properly installed and fasteners
are tight. Pull on leg connectors to confirm they are secure.
󱪼Open one of the stroller frame leg connector Ⓠ assemblies by removing the two Phillips screws
that are loosely threaded into the connector using a Phillips screwdriver tool. Position each leg
connector against its corresponding rear stroller frame leg, so that the triangular Double Stroller Kit
SmartHub Attachment openings are on the inside of the rear leg Ⓟ. Slide the open leg connector
over the rear leg and around the tie rod bolt Ⓡ.
󱪼Close the leg connector over the rear stroller frame leg. Using a Phillips screwdriver tool, fully
tighten the two mounting bolts to secure the connector in place. Check your installation by twisting
on the connector to ensure it does not move. Repeat with the other connector.
󱫉Assembling and attaching the Double Stroller Kit SmartHub Attachment
⚠ WARNING ⚠FALL HAZARD:
◦ Always check that the Double Stroller Kit SmartHub Attachment is securely locked into
the stroller frame leg connectors before placing your child into stroller or starting to stroll.
Pull backwards on the Double Stroller Kit SmartHub Attachment and check that the red
warning triangles on both sides are NOT visible.
󱪼Insert the two Double Stroller Kit SmartHub Attachment wheels Ⓞ. You will hear a CLICK when
they are locked in place.
󱪼Grasp the Double Stroller Kit SmartHub Attachment with one hand while holding the stroller frame
with your other hand. Pull on the release lever Ⓚand guide both tube ends into the stroller frame
leg connectors Ⓠuntil they are fully inserted and the red warning triangles have been fully covered
by the stroller frame leg connectors. You will hear a CLICK when the Double Stroller Kit SmartHub
Attachment is locked in place.

10 – ENGLISH – Manual Text Booklet – Orbit Baby Double Stroller Kit
󱪼Check that the Double Stroller Kit SmartHub Attachment is fully locked into the stroller frame by
letting go of the release lever and pulling back on the attachment. You should not see the red
warning triangles or be able to remove the attachment.
󱫋Attaching the ShadePad
󱪼Undo the hook and loop fasteners on the backside of the ShadePad Ⓐ. Grasp the ShadePad by
its sides and slide it over the Unibar while pulling it wide open, until the bottom of the ShadePad
lines up with the end of the foam grip. Ensure that the clear window faces upward, the flap with the
two snaps faces the Unibar, and the ShadePad is only on the foam of the Unibar.
󱪼Attach the strips of hook and loop fastener on the underside of the ShadePad. Make sure that in
doing so the upper two elastic bands remain covered.
󱪼Snap both corners of the ShadePad to the water bottle tray Ⓙ.
Assembly of the Orbit Baby Double Stroller Kit is now complete.

Manual Text Booklet – Orbit Baby Double Stroller Kit – ENGLISH – 11
Using your Orbit Baby seats with the Double Stroller Upgrade Kit
⚠ WARNING ⚠ FALL HAZARD: Avoid serious injury from falls or sliding out.
◦ Restraint harness use is required for all use modes when harness is present on the
product. Always secure your child to avoid serious injury from falling or sliding out. Always
use both the shoulder and lap portions of the harness.
◦ Never let your child climb into or out of a seat unassisted.
STRANGULATION HAZARD:
◦ Children have STRANGLED in loose or partially buckled harness straps. Fully restrain the
child at all times.
PINCH HAZARD:
◦ When docking or adjusting your seats, keep hands and fingers, especially those of children,
clear of moving parts and the SmartHubs.
◦ Keep SmartHub areas clean. Keep all metal and plastic parts clear of objects, debris and
liquids to allow proper and safe functionality.◦ Listen for audible CLICK which indicates that seats are locked into the SmartHubs.
◦ Always check that the Orbit Baby seats are securely locked into the SmartHubs by tugging
upwards and turning.
◦ Lock the stroller wheels and check stability of the stroller before placing your children in or
removing your children from seats.

12 – ENGLISH – Manual Text Booklet – Orbit Baby Double Stroller Kit
⚠ WARNING ⚠◦ Always make sure that the seat is locked in forward-facing position [front and rear
SmartHubs] or rear-facing position [front SmartHub] before strolling. Side-facing locked
positions are for stationary use only. Do not rotate seats when the stroller is in motion.
◦ Lock the parking brakes and check stability when the stroller is stationary.
󱫍 Loading your child into the rear SmartHub seat
󱪼Rotate the infant car seat by pulling one or both levers and rotating the seat into the sideways
loading position. Rotate the stroller seat or bassinet by pulling both levers and rotating the seat
to a sideways loading position.
󱪼Place your child in the seat and secure according to the seat’s instruction manual. Rotate the seat
forward-facing to begin strolling.
󱫏Restrictions on the double stroller frame
⚠ WARNING ⚠◦ DO NOT USE ANY SEAT ON REAR SMARTHUB IN REAR FACING POSITION.
◦ DO NOT use stroller seats on the front and rear SmartHubs facing each other in fully
reclined position.
◦ DO NOT use any Toddler Car Seat on the rear SmartHub.
◦ ONLY USE Stroller Seat, Infant Car Seat, Toddler Car Seat, and Bassinet in side facing
position when stationary.
◦ Keep hands and fingers clear of moving parts when adjusting the Unibar.
󱪼Never use both stroller seats in the position shown in the diagram; a child’s feet could become
pinched between the footrests. Avoid injury to the child in rear seat from kicking or contact with
footrest on stroller seat; only use footrest adjustment position 1 when stroller seat is rear-facing on
the front SmartHub.