Orca RUNplus User manual

Radio & Esc setup
Transmitter Settings:
Throttle Travel Maximum / 100%
Brake Travel Maximum / 100%
Throttle Exponential Start with 0%
Throttle Neutral Trim Center / 0
Throttle Servo Reverse Reverse (Futaba, KO, Sanwa)
Initial set-up of the throttle end-points of the ESC:
* Connect the power wires of the ESC to a fully charged battery set; making sure the
polarity is correct.
* Bind your receiver and transmitter first if your radio requires you to do so.
* Turn on the transmitter and hold the throttle at full brake position.
* Turn on ESC and listen for 2 beeps.
* After you hear the 2 beeps, apply full throttle and listen for another 2 beeps.
* Once you hear the 2 beeps, release the throttle to neutral position.
* A beep will then sound, signifying that the ESC endpoints have been successfully set.
Note! If you do not hear the beeping sound as described above, try reversing the throttle
reverse setting in the transmitter.
Operation
* Install/Solder the relevant battery connector (Battery Specific) to the battery wires.Red
to +ve and Black to -ve. (WARNING! Reversing the battery polarity will destroy your
ESC and void the warranty.)
* Connect supplied BEC wire(200mm) to 3pin port match the (- + s) between the receiver
connector and ESC.
* Connect the 3 motor wires(Brushless motor) or 2 motor wire(Brushed Motor) to the
motor. The connector suggest use the ESC connected plug. Match the label of the ESC
Output (A, B, C) to the Tablabels on the motor when soldering. Avoid soldering each joint
for longer than 5 seconds. Prior to operation make sure you have not created a short by
either creating a wire bridge or solder bridge on the solder tabs on the motor.
(WARNING! Improper wiring may damage the ESC and void the warranty.)
* Connect the sensor cable between the ESC sensor plug and the Motor sensor plug.(
* Connect the receiver plug to the CH2/throttle pin of the receiver.
Instruction Manual
Vers ion 1.03
Dual System
Brushless / brushed
Thank you for choosing ORCA Products. Welcome to join our dual system
convenience of power RC. By purchasing the Run-plus Electronic Speed
Control ("ESC") you have chosen one of the most advanced speed controls
in RC. The Run-plus allow to use brushless or brushed motor to driver, The
esc attach the LED program card let you easy to change the setup of ESC,
The first of ORCA speedo have Dual system function. Please read this
manual thoroughly to familiarize yourself with the installation, setup and
operation. By operating this product, you accept the ORCA Warranty
Terms.
Specification
*******Dual System*******
Brushless(sensor with turbo) or Brushed
System: Dual Brushless or Brushed System
Forward/Brake/Reverse: Yes (Factory preset at Forward/Brake)
Dimensions: 29.5(L) x 29.7(W) x17.6mm(H)
Weight: 22g (excluding wires)
Voltage Input: 6V-12.6V (Lipo 2~3Cells)
Peak Current: 310A
Continuous current : 80A
Motor Limit: Over 10.5Turns
Motor Type: Sensored 540 sized brushless motors or
Brushed motor
B.E.C.: 4A_6V
Multi Protection System: Yes
6V-12.6V
Ca pa ci to r
ABC
CH 4
CH 3
CH 2
Ch1
(B EC c a bl e)
Cool ingFa n
Installation & Con nector s
+Re d
-Bl ack
-Black
+Red
A
B
C
Se nso r ca ble
Brushed
System
Brushless
(Sensor ed with Turbo)
Dual
Syste m
Model:
Brushless
System
Brushless
(Sensor ed with Turbo)
Dual
Syste m
Model:
WARNING!
1.) Motor A+B-C must match the
ESC Initial Setup.
2.) Item and Value program
setup must be match the
motor type.
(Otherwise will damage the ESC.)
WARNING!
1.) Motor +/- polar must match the
ESC Initial Setup, otherwise
the motor rotation will reverse.
2.) Item and Value program
setup must be match the
motor type.
(Otherwise will not work of the ESC.)
-
+
Rece iver
(B EC c a bl e) Red
Bec cable
OFF ON Power Switch
Ca pa ci to r
+
Rece iver
CH 4
CH 3
CH 2
Ch1
(B EC c a bl e)
Cool ingFa n
+Re d
-Bl ack
-Black
+Red
Red
Bec cable
OFF ON Power Switch +
6V-12.6V
-
-
Detailed Explanation of each Function Menu items
1) Running Mode
Froward/Brake-------This function the car will not have reverse function, Just forward and brake.
Forward/Rev--------- This function the car will reverse immediately when the throttle brake the car.
Froward/Brk/Rev--- Set this function the first touch of throttle brake the car will have brake function, and if you release to center
position after brake and continue brake again the reverse function will appear.
2) Battery Type
Lipo, Li-Fe or Nixx select.
3.) Battery Cut-Off Voltage
Lipo --- Low ------ cut off at 2.9V/cell Li-Fe — Low ------ cut off at 2.2V/cell Nixx — Low
Middle -- cut off at 3.2V/cell Middle--- cut off at 2.5V/cell Middle — cut off at 4.0V/ total
High ----- cut off at 3.4V/cell High ------ cut off at 2.8V/cell High
Disable - No cut off protect Disable - No cut off protect Disable - No cut off protect
4) Initial start force
Usually the throttle force starts from 1% to 100%; it can let you get the best linear control feeling. This function can let you get a
more aggressive feeling in the throttle. You can choose the throttle start point at 5%, 10%, 15%, 20%, 25%, 30% or 35% to 100%.
This function comment is used in brushed motors, because the power of brushed motors is typically weak than brushless motors.
5) Punch
Allows you to change the punch of the ESC (Level 1 to Level 5). Level 1 has the most miniature punch and Level 5 has the highest
punch. Adjust punch level to maximize acceleration speed with minimum wheel spin.
6) PWM(Driver Freq)
Allows you to change the forward drive frequency of the ESC (“2K to 24K From six-step)
* The 2K setup will give you good punch at the low end.
* The 24K setup will result in strong mid to top end.
* Experiment to find out what suits your driving style best.
7) Timing
Allows you to adjust the timing of the motor (0º-100º Mode 1º increments): Generally speaking, in brushless systems, an increase in
timing will result in an increase in the RPM of the motor. However, an increase in timing also will decrease the efficiency of the
system, thus generates heat on the ESC and motor.
8.) Turbo Timing
Turbo Timing is unique to brushless systems because the ESC can simulate motor timing advance. While mechanical timing
advance in a brushed motor system is limited by the physical phasing of the motor, brushless ESC timing advance can push beyond
that physical limit. As a result, motors can run at a super-high RPM in the Turbo Timing mode, resulting in a sensation of having a
2nd gear/Turbo for top speed. This menu allows you to adjust the amount of Turbo Timing in your rake ESC in 1º increments. (The
“Turbo Timing” should never be greater in value than Timing)
9) Motor rotation
CCW — Motor clockwise rotation, fit for over 90% car kit.
CW — Motor anti-colckwise rotation, fit for some special car kit.
10) Drag Brake
Set the automatic brake force applied when the throttle returns to neutral position (8 steps from Off to 100%):
* 60%, 80% and 100% Drag Brake recommend used in Crawl only.
11) Max Reverse Force
Control the Maximum Reverse power when you Reverse the car.
12) Brake Punch
When you set Punch 6, the brake time will follow your throttle brake simple and direct, if you used Punch 1-5 the brake
feeling have something ABS, get more smooth.
13) Brake PWM(Brake Freq)
Brake PWM operates similar to PWM except it affects the braking instead of the throttle (4 steps from 600hz to 4khz)
* At 600 Hz, the Drag brake and the Brake force will feel the punchiest.
* At 4k Hz, the Drag brake and the Brake will feel smooth.
14) Neutral Range
Set the sensitive relay to your throttle feeling, preset in 9%.
15) Motor Type
This is a special function of the “RUN PLUS” ESC, it can let you choose two different type of motor, Brushless motor or
Brushed motor, but please carefully to select the “Value" of “Item” 15, because Improper configuration may damage the ESC.
LED
LED
LED
SET
SET
LED
LED
LED
SET
SET
All ORCA products are manufactured in accordance with the highest quality standards. ORCA guarantees this product to be free from defects in materials or workmanship for 60
days from the original date of purchase verified by sales receipt. This limited warranty does not cover damages resulting from abnormal wear, misuse or improper product
maintenance.
To avoid unnecessary service and mailing charges, always eliminate all other possibilities and check all components for malfunctions before sending in your unit for repair.
Products sent in for repair that operate perfectly will be charged a service fee.
When sending in the product, always pack carefully and include the original sales receipt, a description of the problem encountered, your return address and contact information.
Since we do not have control over the installation and use of this product, we cannot accept any liability for any damages resulting from the usage of this product. Therefore,
using this product is at your own risk, and the user accepts all resulting liability from installing and using the product.
Copyright@2023 . All Rights Reserved.
Setting by LED Program Card
How to used the LED Program Card
to setup the ESC.
Brushless
(Sens ore d wit h Turb o)
Dual
System
Model :
Refer to here
Punch
PWM
Timing
Turbo Timing
Motor rotation
Drag Brake
Brake Punch
Brake PWM
Neutral Range
Motor Type
Lipo Li-Fe Nixx
Forward/
Brake
Forward/
Rev
Forward/
brake/Rev
Item Value
RunningMode
Battery Type
Battery Cut-Off
Voltage
Initial Start
Force
Max Reverse
Force
Low Middle High Disabled
1% 5% 10% 15% 20% 25% 30% 35%
2K 4K 8K 12K 16K 24K
Level1 Level2 Level3 Level4 Level5
OFF 10° 20° 30° 40°
OFF 10° 20° 30° 40° 50° 60°
CCW CW
OFF 5% 10% 20% 40% 60% 80% 100%
25% 50% 75% 100%
600Hz 1K 2K 4K
3% 6% 9% 12% 15%
Brushless Brushed
Level1 Level2 Level3 Level4 Level5 Level6
These two-function work
with a brushless motor
only
Brushless
(Sens ore d wit h Turb o)
Dual
System
Model :
Refer to here
“Select” bu tto n
control
Item No.
“ “ “ “ butto n
contr ol
Value No .
Press and hole 5 sec
back to default setting.
Double-press the “Enter” button
will succeed in your programming.
BEC Cable
Bec cable
+
(B EC c ab le )
Coo lin gFan
Bec cable
OFF O N
Power Swi tch
For example: Now set the Punch to Level4
1) Plug “BEC” cable to the program card.
2) Esc connect the battery and then turn it on.
3) Press the “Select” button one by one until
the “Item” no. up to “5".
4) Press the “ “ button one by one until the
“Value” no. up to “4".
5) Press the “Enter” button and then, the card
will show “ SE” and “nd”, now; all data are
ready to send but not successful.
6) Press the “Enter” button again, and then the
card will show “SU” and “CC”, now the
programming are succeeful.
How to used the button to setup the ESC without program card:
(Transmitter must be turn on during setup the esc without program card.)
1.Connect the power wires of the ESC to a fully charged battery set; making sure the polarity is correct.
2.Used the 1.5mm screw to press the set hole button before switch on the esc, switch on esc and then hold
the button contiue about 2 second to wait the LED light off and hear the motor long beep sound appear.
3.Set hole button only to let you choice the function mode, red LED will flash one time to eleven time represent
which function you want to set.
4.Transimitter will let you change the participate of each function,
full throttle once time will increase one participate e.g. (the blue LED will flash two time from one time).
full brake once time will decrease one participate e.g. (the blue LED will flash one time from two time).
5.When you finish setup you can switch off the esc directly, it can save automatically.
Esc back to default setup:
Used the 1.5mm screw to press the set hole button before switch on the esc, switch on the esc and then
hold the button contiue about 3 second to wait the LED light сhange to orange сolor and hear the motor long
beep sound and then keep continue press the set button until the LED change from orange color to
red and blue led light fast flash.
Release the set button and switch off the esc.
Setting without Program Card
Punch
PWM
Timing
Turbo Timing
Motor rotation
Drag Brake
Brake Punch
Brake PWM
Neutral Range
Motor Type
Lipo Li-Fe Nixx
Forward/
Brake
Forward/
Rev
Forward/
brake/Rev
Item Value
RunningMode
Battery Type
Battery Cut-Off
Voltage
Initial Start
Force
Max Reverse
Force
Low Middle High Disabled
1% 5% 10% 15% 20% 25% 30% 35%
2K 4K 8K 12K 16K 24K
Level1 Level2 Level3 Level4 Level5
OFF 10° 20° 30° 40°
OFF 10° 20° 30° 40° 50° 60°
CCW CW
OFF 5% 10% 20% 40% 60% 80% 100%
25% 50% 75% 100%
600Hz 1K 2K 4K
3% 6% 9% 12% 15%
Brushless Brushed
Level1 Level2 Level3 Level4 Level5 Level6
These two-function work
with a brushless motor
only
Blue light Blue light Blue light Blue light Blue light Blue light Blue light Blue light
Flash one time Flash two times Flash three times Flash four times Flash five times Flash six times Flash seven times Flash eight times
Red light flash
one time
Red light flash
two times
Red light flash
three times
Red light flash
four times
Red light flash
five times
Red light flash
Six times
Red light flash
Seven times
Red light flash
Eight times
Red light flash
Nine times
Red light flash
Ten times
Red light flash
Eleven times
Red light flash
Twelve times
Red light flash
Thirteen times
Red light flash
Fourteen times
Red light flash
fifteen times
LED
LED
LED
SET
SET

All ORCA products are manufactured in accordance with the highest quality standards. ORCA guarantees this product to be free from defects in materials or workmanship for 60
days from the original date of purchase verified by sales receipt. This limited warranty does not cover damages resulting from abnormal wear, misuse or improper product
maintenance.
To avoid unnecessary service and mailing charges, always eliminate all other possibilities and check all components for malfunctions before sending in your unit for repair.
Products sent in for repair that operate perfectly will be charged a service fee.
When sending in the product, always pack carefully and include the original sales receipt, a description of the problem encountered, your return address and contact information.
Since we do not have control over the installation and use of this product, we cannot accept any liability for any damages resulting from the usage of this product. Therefore,
using this product is at your own risk, and the user accepts all resulting liability from installing and using the product.
Copyright@2023 . All Rights Reserved.
Setting by LED Program Card
How to used the LED Program Card
to setup the ESC.
Brushless
(Sens ore d wit h Turb o)
Dual
System
Model :
Refer to here
Punch
PWM
Timing
Turbo Timing
Motor rotation
Drag Brake
Brake Punch
Brake PWM
Neutral Range
Motor Type
Lipo Li-Fe Nixx
Forward/
Brake
Forward/
Rev
Forward/
brake/Rev
Item Value
RunningMode
Battery Type
Battery Cut-Off
Voltage
Initial Start
Force
Max Reverse
Force
Low Middle High Disabled
1% 5% 10% 15% 20% 25% 30% 35%
2K 4K 8K 12K 16K 24K
Level1 Level2 Level3 Level4 Level5
OFF 10° 20° 30° 40°
OFF 10° 20° 30° 40° 50° 60°
CCW CW
OFF 5% 10% 20% 40% 60% 80% 100%
25% 50% 75% 100%
600Hz 1K 2K 4K
3% 6% 9% 12% 15%
Brushless Brushed
Level1 Level2 Level3 Level4 Level5 Level6
These two-function work
with a brushless motor
only
Brushless
(Sens ore d wit h Turb o)
Dual
System
Model :
Refer to here
“Select” bu tto n
control
Item No.
“ “ “ “ butto n
contr ol
Value No .
Press and hole 5 sec
back to default setting.
Double-press the “Enter” button
will succeed in your programming.
BEC Cable
Bec cable
+
(B EC c ab le )
Coo lin gFan
Bec cable
OFF O N
Power Swi tch
For example: Now set the Punch to Level4
1) Plug “BEC” cable to the program card.
2) Esc connect the battery and then turn it on.
3) Press the “Select” button one by one until
the “Item” no. up to “5".
4) Press the “ “ button one by one until the
“Value” no. up to “4".
5) Press the “Enter” button and then, the card
will show “ SE” and “nd”, now; all data are
ready to send but not successful.
6) Press the “Enter” button again, and then the
card will show “SU” and “CC”, now the
programming are succeeful.
How to used the button to setup the ESC without program card:
(Transmitter must be turn on during setup the esc without program card.)
1.Connect the power wires of the ESC to a fully charged battery set; making sure the polarity is correct.
2.Used the 1.5mm screw to press the set hole button before switch on the esc, switch on esc and then hold
the button contiue about 2 second to wait the LED light off and hear the motor long beep sound appear.
3.Set hole button only to let you choice the function mode, red LED will flash one time to eleven time represent
which function you want to set.
4.Transimitter will let you change the participate of each function,
full throttle once time will increase one participate e.g. (the blue LED will flash two time from one time).
full brake once time will decrease one participate e.g. (the blue LED will flash one time from two time).
5.When you finish setup you can switch off the esc directly, it can save automatically.
Esc back to default setup:
Used the 1.5mm screw to press the set hole button before switch on the esc, switch on the esc and then
hold the button contiue about 3 second to wait the LED light сhange to orange сolor and hear the motor long
beep sound and then keep continue press the set button until the LED change from orange color to
red and blue led light fast flash.
Release the set button and switch off the esc.
Setting without Program Card
Punch
PWM
Timing
Turbo Timing
Motor rotation
Drag Brake
Brake Punch
Brake PWM
Neutral Range
Motor Type
Lipo Li-Fe Nixx
Forward/
Brake
Forward/
Rev
Forward/
brake/Rev
Item Value
RunningMode
Battery Type
Battery Cut-Off
Voltage
Initial Start
Force
Max Reverse
Force
Low Middle High Disabled
1% 5% 10% 15% 20% 25% 30% 35%
2K 4K 8K 12K 16K 24K
Level1 Level2 Level3 Level4 Level5
OFF 10° 20° 30° 40°
OFF 10° 20° 30° 40° 50° 60°
CCW CW
OFF 5% 10% 20% 40% 60% 80% 100%
25% 50% 75% 100%
600Hz 1K 2K 4K
3% 6% 9% 12% 15%
Brushless Brushed
Level1 Level2 Level3 Level4 Level5 Level6
These two-function work
with a brushless motor
only
Blue light Blue light Blue light Blue light Blue light Blue light Blue light Blue light
Flash one time Flash two times Flash three times Flash four times Flash five times Flash six times Flash seven times Flash eight times
Red light flash
one time
Red light flash
two times
Red light flash
three times
Red light flash
four times
Red light flash
five times
Red light flash
Six times
Red light flash
Seven times
Red light flash
Eight times
Red light flash
Nine times
Red light flash
Ten times
Red light flash
Eleven times
Red light flash
Twelve times
Red light flash
Thirteen times
Red light flash
Fourteen times
Red light flash
fifteen times
LED
LED
LED
SET
SET