Oregon Scientific RMR612HGA User manual

Wireless Thermo-Hygro Clock
Model : RMR612HGA
User Manual
RMR612HGA lab test cover R21/8/04, 7:00 PM1

EN
1
CONTENTS
Contents ................................................................... 1
Introduction .............................................................. 2
About Oregon Scientific .......................................... 2
Product Overview .................................................... 3
Front View .............................................................. 3
Back View .............................................................. 4
Remote Sensor (THGR122NX) ............................. 5
Getting Started ......................................................... 6
Batteries ................................................................. 6
Change Settings .................................................... 6
Remote Sensor (THGR122NX) ................................ 6
Setup Sensor ......................................................... 6
Data Transmission ................................................. 7
Search for Sensor .................................................. 7
Clock ......................................................................... 8
Turn Atomic Clock ON/OFF ................................... 8
Set Clock ............................................................... 8
Switch Clock Display ............................................. 8
Alarm ......................................................................... 9
View Alarm Settings ............................................... 9
Set Alarm ............................................................... 9
Activate Alarm ........................................................ 9
Silence Alarm ......................................................... 9
Temperature and Humidity ...................................... 9
Select Temperature Unit ........................................ 9
Select Sensor Channel .......................................... 9
Minimum / Maximum Records ............................. 10
Temperature and Humidity Trend ........................ 10
Reset System ......................................................... 10
Safety and Care ...................................................... 10
Warnings ................................................................. 11
Troubleshooting ..................................................... 11
Specifications ......................................................... 12
Main Unit Dimensions .......................................... 12
Remote Sensor Dimensions ................................ 12
Temperature ......................................................... 12
Relative Humidity ................................................. 12
Remote Sensor (THGR122NX) ........................... 12
Clock .................................................................... 12
Power ................................................................... 12
FCC Statement ....................................................... 13
RMR612HGA lab test R2 1/17/04, 4:57 PM1

EN
2
INTRODUCTION
Thank you for selecting the Oregon ScientificTM Clock
with Indoor / Outdoor Temperature and Humidity
(RMR612HGA). This device bundles precise time
keeping, alarm, and temperature and humidity
monitoring features into a single tool you can use from
the convenience of your home.
In this box, you will find:
•Main unit
•Remote sensor (THGR122NX)
Keep this manual handy as you use your new product.
It contains practical step-by-step instructions, as well
as technical specifications and warnings you should
know.
ABOUT OREGON SCIENTIFIC
Visit our website (www.oregonscientific.com) to learn
more about other Oregon Scientific products such as
digital cameras, hand-held organizers, health and fitness
gear, and projection clocks. The website also includes
contact information for our customer service department,
in case you need to reach us.
RMR612HGA lab test R2 1/17/04, 4:58 PM2

EN
3
PRODUCT OVERVIEW
FRONT VIEW
1. SNOOZE button: Activate 8-minute snooze.
2. Humidity Area: Readings; trend line, remote unit
reception and channel number
3. Clock / Alarm Area: Time, time zone, day of week,
alarm, and Atomic Clock reception status
4. Temperature Area: Readings, trend line, and
battery status
5. button: View alarm settings, activate alarm
RMR612HGA lab test R2 1/17/04, 4:58 PM3

EN
4
BACK VIEW
1. Wall mount
2. CHANNEL button: Switch remote sensor
3. MEM: View current, maximum and minimum
temperature / humidity readings
4. Battery compartment
5. RESET hole (located in battery compartment)
6. MODE button: Change display / settings
7. : Increase setting, activate Atomic Clock signal
reception
8. : Decrease setting
9. °C / °F switch (located in battery compartment)
10. ZONE: Switch time zones, deactivate Atomic Clock
signal reception (located in battery compartment)
1
2
3
4
5
6
7
8
9
10
RMR612HGA lab test R2 1/17/04, 4:58 PM4

EN
5
REMOTE SENSOR (THGR122NX)
1. LCD display
2. LED Status indicator
1. Wall mount hole
2. RESET
3. Channel number (1 - 3)
4. Battery compartment
(Battery compartment cover not shown)
1
2
1
2
3
4
RMR612HGA lab test R2 1/17/04, 4:58 PM5

EN
6
GETTING STARTED
BATTERIES
Insert batteries before first use, matching the polarity as
shown in the battery compartment. For best results,
install batteries in the remote sensor before the main
unit. Press RESET after each battery change.
Do not use rechargeable batteries.
NOTE
shows when batteries are low.
UNIT LOCATION
MainTemperature Area when
INDOOR temperature is
shown.
Remote Temperature Area when
OUTDOOR temperature is
shown.
CHANGE SETTINGS
1. Press and hold MODE for 2 seconds to enter setting
mode.
2. Press UP or DOWN to change settings.
3. Press MODE to confirm.
REMOTE SENSOR (THGR122NX)
This product is shipped with a THGR122NX Thermo/
Hygro Sensor that collects Temperature and Humidity
data. Data can be collected from up to 3 sensors.
Additional sensors sold separately.
3. Place the sensor near the main unit. Press RESET
on the sensor to initiate signal sending between the
sensor and the main unit. The reception icon on
the main unit will blink for approximately 3 minutes
while it is searching for the sensor. (Refer to the
Sensor Data Transmission section for more
information.)
4. Close the remote sensor battery compartment.
5. Secure the sensor in the desired location using the
wall mount or table stand.
SETUP SENSOR
Open the remote sensor battery compartment with a
small Phillips screwdriver.
1. Insert the batteries, matching the polarity as shown
in the battery compartment.
2. Set the channel. The switch is located in the
battery compartment.
SWITCH OPTION
Channel Channel 1 - 3. If you are using
more than one sensor, select a
different channel for each sensor.
RMR612HGA lab test R2 1/17/04, 4:58 PM6

EN
7
For best results:
•Insert the batteries and select the channel and
temperature unit before you mount the sensor.
•Place the sensor out of direct sunlight and
moisture.
•Do not place the sensor more than 30 meters
(98 feet) from the main (indoor) unit.
•Position the sensor so that it faces the main
(indoor) unit, minimizing obstructions such as
doors, walls, and furniture.
•Place the sensor in a location with a clear view
to the sky, away from metallic or electronic
objects.
•Position the sensor close to the main unit
during cold winter months as below-freezing
temperatures may affect battery performance
and signal transmission.
You may need to experiment with various locations to
get the best results.
SEARCH FOR SENSOR
To search for a sensor, press and hold MEM and
CHANNEL for 2 seconds.
If the sensor is still not found, check the
batteries, obstructions, and remote unit location.
Signals from household devices such as
doorbells, electronic garage doors, and home security
systems may cause temporary reception failure. This is
normal and does not affect general product performance.
The reception will resume once the interference ends.
NOTE
DATA TRANSMISSION
Data is sent from the sensor(s) every 40 seconds.
The reception icon shown in the Temperature and
Humidity Areas shows the status.
--- shows in Temp/
Humidity Areas
ICON DESCRIPTION
Main unit is searching for
sensors.
At least 1 channel has
been found.
Channel 1 is selected (the
number will change
depending on the sensor
you select).
The selected sensor cannot
be found. Search for the
sensor or check batteries.
NOTE
RMR612HGA lab test R2 1/17/04, 4:58 PM7

EN
8
CLOCK
This product shows the current time, time zone, and day
of week in English, Spanish, or French. The time is
automatically updated by the US Atomic Clock in
Boulder, Colorado unless you disable this feature.
Signals are collected by the main unit when it is within
1500 km (932 miles) of a signal.
Initial reception takes 2 - 10 minutes, and is initiated
when you first setup the unit, and whenever you press
RESET. Once complete, the reception icon will stop
blinking. The icon is shown in the Clock Area.
To force a manual search for Atomic Clock signals, press
and hold UP for 2 seconds. If no signal is found, check
the batteries.
TURN ATOMIC CLOCK ON/OFF
Perform this step if you cannot receive Atomic Clock
signals. Press and hold ZONE (located in the battery
compartment) for 2 seconds. Then, manually set the
clock following the “Set Clock” instructions (below).
The signal icon indicates that the Atomic Clock
feature is ON. No icon means that it is OFF.
SET CLOCK
You only need to do this if you have disabled the Atomic
Clock feature (for example, if you are too far from or
cannot receive a signal).
1. Open the battery compartment.
2. Press ZONE repeatedly to display the desired Time
Zone: (P) Pacific, (M) Mountain, (C) Central, or
(E) Eastern.
3. Close the battery compartment.
4. Press and hold MODE for 2 seconds. The Clock
Area will blink.
5. Select the hour, minute, year, month, day, and
language. Press UP or DOWN to change the
setting. Press MODE to confirm.
The language options are (E) English,
(F) French, and (S) Spanish.
SWITCH CLOCK DISPLAY
Press MODE to toggle between Clock with Seconds and
Clock with Weekday display.
NOTE
RMR612HGA lab test R2 1/17/04, 4:58 PM8

EN
9
ALARM
This product is equipped with a 2-minute crescendo alarm
and 8-minute snooze.
VIEW ALARM SETTINGS
Press . The Alarm Time and On/Off status will show in
the Clock Area.
SET ALARM
1. Press .
2. Press and hold again for 2 seconds. The Alarm
settings will blink.
3. Select the hour and minute. Press UP or DOWN to
change settings. Press to confirm.
ACTIVATE ALARM
Press to activate or deactivate the Alarm. shows in
the Clock Area when the Alarm is activated.
SNOOZE ALARM
Press SNOOZE to silence the Alarm for 8 minutes.
If no button is pressed, the Alarm will automatically
silence after 2 minutes. It will then sound again after
8 minutes.
TEMPERATURE AND HUMIDITY
This product can display the following temperature and
humidity information:
•Current, minimum and maximum readings
•Trend line
Data is collected by the remote sensors and displayed
every 40 seconds.
SELECT TEMPERATURE UNIT
Slide the °C / °F switch into the desired location. The
switch is located in the battery compartment. The setting
for the main unit overrides the remote sensor setting.
SELECT SENSOR CHANNEL
Press CHANNEL to switch between sensors 1 - 3.
The house icon shows the selected sensor.
Indoor
Display
Display Remote
Display
Channel 1
Kinetic-
wave
Icon
Remote
Display
Channel 2
Remote
Display
Channel 3
RMR612HGA lab test R2 1/17/04, 4:58 PM9