Original Tractor Cabs 11876 Datasheet

CAB #11876
FOR
New Holland Boomer 20 & 25 Tractors
ASSEMBLY INSTRUCTIONS- PARTS LIST
IMPORTANT
READ THIS MANUAL CAREFULLY AND KEEP FOR FUTURE REFERENCE
CAUTION !
REMOVE THE VINYL PANELS FOR TRANSPORT IN AN OPEN TRUCK OR TRAILER
WARNING !
THIS CAB WILL NOT PROTECT OPERATOR FROM INJURIES CAUSED BY ROLLOVER,
COLLISION, OR OTHER ACCIDENTS
11876312 1

WARNING
This cab is designed to provide foul weather protection only. It does not provide protection
from noise, exhaust fumes, chemicals or injury from roll-over, collision, or other accidents.
1. Do not operate machine in confined areas without proper ventilation.
2. Thoroughly check area of operation before using machine.
3. The cab adds height to the machine. Low tree limbs and other overhead structures that did
not interfere with the operation of the machine before, may now be obstacles.
MAINTENANCE INSTRUCTIONS
Periodically check all bolts to see that they are tight. If bolts become loose, failure of cab parts may
occur.
Door latches and hinges should be lubricated with light machine oil for proper operation.
DO NOT CLEAN THE CLEAR PLASTIC WINDOWS WHEN THE PLASTIC IS DRY.
THE CLEAR PLASTIC WILL SCRATCH.
Avoid contact with plastic windows. Keep plastic windows clean by washing them with clear running
water and rubbing with your bare hands, only. The use of a rag, sponge or brush will scratch the plastic.
Liquid soap may also be used for window cleaning. During freezing weather, an automotive windshield
washer solvent may be used.
Use liquid soap and water to clean colored vinyl portions. Scrubbing with a brush or rag is also
permitted on the colored vinyl portions
STORAGE INSTRUCTIONS
Prior to storage clean the windows and colored vinyl parts with a mild automotive detergent, rinse with
clean water and allow to thoroughly dry, Store cab in a clean dry place out of direct sunlight. Avoid
folding plastic windows.
INSTALLATION
READ THIS MANUAL COMPLETELY BEFORE BEGINNING INSTALLATION.
• The right side of the machine is determined from the operators seated position.
• The words "bolt" will refer to a 1/4”x5/8” bolt and "lock nut"’ will refer to a 1/4” lock nut unless
specified otherwise.
• Do not tighten bolts during assembly unless instructed to do so.
• Park tractor on level ground, lower attachments to ground, remove start key.
2

LIMITED WARRANTY
SNOW REMOVAL EQUIPMENT CABS
COVERED BY WARRANTY
ORIGINAL TRACTOR CAB CO., INC., (the "Company") warrants to the owner that each new product listed below is
merchantable and free of defects in workmanship and material.
During the warranty period, the dealer from whom the product was bought, or the Company, will provide, free of charge, parts
and the shipping costs of parts necessary to correct any defect in workmanship and material.
WARRANTY PERIOD
The company products listed below are warranted for the stated period from the date of the original purchase:
1. Cabs for tractors and snow removal equipment 1 Year
2. Company manufactured accessories for above cabs 1 Year
3. Sunshades for lawn and garden tractors 1 Year
4. Repair parts 1 Year
OWNER'S RESPONSIBILITIES
The owner of a new Company manufactured product must do the following to qualify for warranty service :
1. Retain the original invoice or other proof of purchase to avoid unnecessary difficulties in determining eligibility for warranty
work.
2. Notify the dealer from whom the product was bought, or the company, as soon as possible after discovery of a possible
defect, and provide proof of original purchase.
To notify the company write to: Original Tractor Cab Co., Inc., P.O. Box 97, Arlington, IN 46104.
3.the owner may , upon notification by the Company, be required to return the defective part, or parts, to the Company for
inspection and warranty service.
NOT COVERED BY WARRANTY
The following are not covered by this warranty:
1. Transportation charges to and from servicing dealer or the Company;
2. New products that have been subject to misuse, negligence or accident, or have been altered or repaired in a manner not
authorized by the company;
3. Windshield wipers, lights, or accessories that are warranted separately by their respective manufacturers, except
Company agrees to make available to the owner whatever warranty benefits may be made available to the Company by the
manufacturers.
All implied warranties, except to the extent prohibited by any applicable law, shall have no greater duration than the
warranty period for the applicable product, some states do not allow limitation on how long an implied warranty
lasts, so the above limitation may not apply to you.
The Company’s liability arising out of warranties representation, instructions, or defects from any abuse, shall be
limited exclusively to repair or replacing parts under the condition in the warranty, and in no event will Company be
liable for incidental or consequential damages. Some states do not allow the exclusion or limitation of incidental or
consequential damages, so the above limitation or exclusion may not apply to you.
This warranty gives you specific legal rights, and you may also have rights that vary from state to state.
3

Carton Contents: Cab #11801 for New Holland Boomer 20 & 25
PART # KEY # QTY DESCRIPTION
11802 1 1 Foot, RH
11803 2 1 Foot, LH
10926 3 2 Front Post
10010 4 1 Front Cross Bar
10002 5 1 Top Frame Brace, RH
10003 6 1 Top Frame Brace, LH
11804 7 1 Rear Bracket, RH
11805 8 1 Rear Bracket, LH
11806 9 1 Boxing Post, RH
10750 10 1 Rear Post, RH
11807 11 1 Boxing Post, LH
10751 12 1 Rear Post, LH
11815 13 1 ROPS Bracket
10001 14 1 Top Frame
10749-B 15 1 Windshield
11877-B 16 1 Front Panel Vinyl
11808-B 17 1 Rear Curtain
11810-B 18 1 Door, RH
11811 19 1 Door Bottom, RH
11812-B 20 1 Door, LH
11813 21 1 Door Bottom, LH
10000 22 1 Plastic Top
9820 1 Door Hardware Package
11814 1 Hardware Package (Contents Listed Below)
786 14 1/4”-20 x 5/8” Cap Screw
788 6 1/4”-20 x 3/4” Cap Screw
931 2 1/4”-20 x 2 1/2” Cap Screw
1514 4 1/4” Flat Washer
730 22 1/4”-20 Two-Way Locknut
9844 2 5/16” X 1” Fender Washer
8220 2 M8-1.25 x 20mm Cap Screw
11750 4 M12-1.75 x 55mm Cap Screw
3317 4 1/2” Lock Washer
60358 4 1/2” Flat Washer
4902 2 Notched Plastic Cover
4

14
13
11
6
5
9
12
10
3
4
8
7
3
2
Step 1; See Figure 1:
Identify the steel parts by using Figure 1 as
an example. Figure 1
1
5

Step 2; See Figure 2:
Figure 2
Remove handle from left fender.
A. Remove the nuts from the studs that attach
the handle to the fender. Remove the handle.
B. Insert two M8 x 20 mm bolts with fender
washers down through the holes. Replace the
nuts and tighten.
Step 3; See Figure 3:
Figure 3
Install the right & left Foot (1 & 2).
A. Remove the bolts at Reference A.
B. Place the Foot in position and replace the
bolts and nuts. Do not tighten at this time.
C. Repeat the above steps on the left side.
A
1
6

Step 4; See Figure 4:
Install Front Posts (3)
A. Insert a bolt outwards through the lower hole
in the foot and the post. Add a locknut do not
tighten at this time.
C. Insert a bolt outwards through the upper hole
in the foot and the post. Place a hinge from the
door hardware package over the bolt and add a
locknut. Do not tighten at this time.
D. Repeat on left side of tractor.
Figure 4
3
Step 5; See Figure 5:
Install Top Frame Braces (5 & 6) and Front
Panel Cross Bar (4)
5
6
Note: If you are installing the optional safety
glass windshield omit Top Frame Braces.
Note: Bent ends of Top Frame Braces will point
rearwards and lay flat when properly installed.
4
A. Insert a 1/4” x 3/4” bolt forward through the
tab on the post, the end of the Front Panel
Cross Bar and then the lower end of the right
Top Frame Brace. Add a nut and tighten just
enough to hold the brace up.
B. Repeat on left side of tractor.
Figure 5
7

Step 6; See Figure 6:
Install right and left Rear Brackets (7 & 8)
A. Remove the bolts at reference B. Place the
right Rear Bracket over the hole.
B. Insert two M12 x 55mm bolts with 1/2” lock
washers and flat washers down through the
holes. Do not tighten at this time.
B
C. Repeat on the left side with left Rear
Bracket.
7
Figure 6
Step 7; See Figure 7:
Install right and left Rear Posts (10 & 12) and
right and left Boxing Posts (9 & 11).
NOTE: When Rear posts are properly installed,
latch plates will be to the front with the notch to
the outside of the enclosure.
11
A. Insert a 1/4” x 3/4” bolt outwards through the
right Boxing Post, Rear Bracket and then the
Rear Post. Add a nut. Tighten enough to keep
the parts upright.
B. Repeat step 7A on the left side with left
Posts.
12
10
9
Figure 7
8

Step 8; See Figure 8:
Figure 8
Install ROPS Bracket (13).
A. Place the ROPS Bracket clamps over the
ROPS and hold it in place with the ends of the
tube at the ends of the Rear Boxing Posts.
13
B. Insert two 1/4” x 2 1/2” bolts in through the
clamp holes. Add lock nuts and tighten just
enough to hold the Bracket in place.
Figure 9
14
Step 9; See Figure 9:
Install Top Frame (14)
NOTE: The front of the Top Frame has the “L”
tabs located closest to the corners.
A. Place the top frame onto the bent ends of
the Posts, ROPS Bracket and Top Frame
Braces.
B. Insert six bolts up through the Rear Posts,
the Front Posts and the Top Frame Braces. Add
nuts. Do not tighten.
C. Insert two 1/4” x 3/4” bolts up through the
Rear Boxing Posts, ROPS Bracket and Top
Frame corner tabs. Add nuts. Do not tighten at
this time.
9

Step 10; See Figure 10:
Install the Doors for frame / door alignment.
A. Follow the instructions in the Door Hardware
Package to install the Door Bottoms and the
Door Latches.
B. Install, close and latch both Doors.
C. Tighten all bolts from previous steps at this
time. Tighten ROPS bolts to proper torque
specifications.
D. Remove the doors by lifting the door up and
out of the bottom hinge then lowering out of the
top hinge.
Figure 10
Step 11; See Figure 11:
Install Rear Curtain (17).
A. Close the Velcro®flaps around the top frame
at the back and corners.
B. Close the Velcro®flaps around the rear posts
and brackets.
17
C. Hook the springs to the frame behind the
seat.
D. Place a notched Plastic Protector over the
bent ends of each rear post. (See inset)
Figure 11
10

Step 12; See Figure 12:
Connect Windshield (15) and Front Panel Vinyl
(16)
A. Place the Windshield and Front Panel Vinyl
face up on a clean flat surface. Press the
Velcro®together.
15
NOTE: If you are installing the optional glass
windshield refer to the instructions for attaching
the Velcro®strip to the Front Panel Vinyl.
16
Figure 12
Step 13; See Figure 13:
Install Windshield (15) and Front Panel Vinyl
(16).
A. Lay the rod sewn into the top of the
windshield over the top frame. Close the
Velcro®flaps around the corners of the top
frame.
15
B. Secure the ties to the cross bar and Close
the Velcro®flaps around the posts.
C. Open the Velcro®flap and fit the vinyl around
the loader control.
16
D. Hook the springs under the step plates.
Figure 13
11

Step 14; See Figure 14:
Figure 14
Install Doors and Top (22).
A. Make sure that the rod sewn into the
windshield is lying over the top frame. (Plastic
Windshield only) Place the top over the top
frame.
22
B. Place four ¼” flat washers over each of four
bolts. Insert bolts inwards, add locknuts and
tighten.
C. Reinstall the doors per the instructions in the
door hardware package. Connect the Velcro®
strips on the lower door & front panel.
Optional C ab Accessories:
#10120 Safety Glass Windshield
#10122 Electric Wiper
# 9855 Flashing Amber Caution Light
#11133 Rear View Mirror, R or L Mount
#11560 Work Light Kit
12

For Replacement Parts and Accessories Contact:
Original Tractor Cab Co., Inc.
P.O. Box 97 6849 W. Front St.
Arlington, IN 46104
Phone [phone]
Fax [phone]
Email [email protected]
Visit us on the web to see our other products.
www.originalcab.com
Cabs for Lawn Tractors, Garden Tractors, Compact Tractors, Snow Blowers, Utility Vehicles
Sunshades for Tractors, Mowers, & Utility Vehicles
Storage Covers for Lawn and Garden equipment
13