ORIGO CF1519 User manual

Instruction Manual
CF1519
*使用風扇前，請先細閱使用說明，並請妥善保存以便將來翻閱。
*Read all instructions carefully before using the FAN, and keep this instruction for furture
reference when necessary.
使用說明書
立體搖擺對流掛牆扇
3D convection wall fan

Important Safety Information
重要安全提示
1
拔除插頭時不可拉扯電源線，必須緊握插頭
，把插頭拔出。
Do not pull the power cord to disconnect
from power source. Always grasp the plug
to pull out.
請使用獨立插座。使用萬能插頭或拖板，容
易發生危險。
Avoid using extension cord as it may
overheat and casue fire.
使用風扇前，請確定規格標貼上所示的額
定電壓與當地供電電壓相同。如有疑問可
向供應商查詢。
Before using the Fan, check if the
voltage marked on the rating label
corresponds to the mains at your
home.
220-240V~ 50-60Hz
包裝物料並非玩具，不可讓小孩玩耍。
Do not let children play parts of
package.
打開包裝，檢查風扇。如發現產品有損壞
，請勿使用及即時聯絡供應商。
Open the package and ensure that the
Fan is undamaged. In case of doubt
do not use the FAN Cooler and contact
your supplier.
必須按照使用說明指示操作本風扇，否則
可能引致產品損壞、短路、火警或人命損
傷。
Use this Fan only as described in
this manual. Any other use not
recommended by the manufacturer
may casue fire, electrical shock or
injury to persons.
使用本風扇前，請先細閱使用說明。
Read all instructions carefully before
using the Fan.
本機不是為體質、感覺或智力有障礙人士(包
括小孩)或缺乏經驗及知識者使用，除非他們
曾經接受負責安全人士的監督或指示，大人應
指導小孩不可把玩電器。
This appliance is not intended for use by
persons (including children) with reduced
physical, sensory or mental capabilities, or
lack of experience and knowledge, unless
they have been given supervision or
instruction concerning use of the appliance
by a person responsible for their safety.
Children should be supervised to ensure
that they do not play with the appliance.
立體搖擺對流掛牆扇
3D convection wall fan

Important Safety Information
重要安全提示
2
不可在潮濕或有積水的環境使用，不可將風
扇擺放於浴缸或大型溶器上面。
The Fan is not intended for use in wet
or damp locations. Never locate the
Fan where it may fall into a bathtub or
other water container.
請保持清潔以維持風扇處於良好狀態
(詳細請參閱清理及維護部份)。
Keep the Fan clean to maintain in good
condition (refer to maintenance
section).
切勿將 風扇 擺放在發熱源頭或火源附近。
Do not place the Fan near a source
of heat or fire.
警告；清理前必須先拔除電源插頭。若電
源線損壞，必須交由製造商或其代理指定
維修服務中心檢查及修理。
WARNING: To avoid danger of electric
shock, unplug from outlet when not
in use and before cleaning. If the
power cord is damaged, it must be
replaced by the manufacturer, its
service agent or similarly qualified
persons in order to avoid hazard.
本風扇不適用於室外及作工業用途。
This Fan is intended for household
use ONLY and not for industrial
or outdoor use.
非使用風扇時請拔除插頭，切斷電源。
Do not leave the Fan unattended.
Always unplug the Fan Cooler when
not in use.
切勿將任何異物放入風扇內；或阻擋風扇
出風口及入風口，皆因以上一切行為均可
能導致風扇損壞。
Do not insert any objects into the Fan
as it may cause an electric shock or
damage. Do not block or tamper with
the Fan in any manner while it is in
operation.
警告：開/關鍵不應作為切斷電源的用途。
WARNING: The On/Off switch should
not be used as the sole means of
disconnecting power. Always unplug
the power cord before servicing or
moving the unit.
如須移動風扇，請先拔除插頭切斷電源。
Always disconnected the Fan from the
power supply when moving it from
one location to another.
本產品含有可回收材料，不可把本產
品作為未分類廢物。請聯繫當地就近
指定回收點。
This product contains recyclable
materials. Do not dispose this
product as unsorted municipal
waste. Please contact your local
municipality for the nearest collection
立體搖擺對流掛牆扇
3D convection wall fan

Control Panel
控制面版
Rear Grille
後網
Front Grille
前網
Wall Fan Holder
掛牆扇掛座
Remote Receiver
遙控信號接收窗
Main Parts
各部名稱
3
Air Oulet
出風口
Air Inlet
入風口
Power Cord
電源線
Plug
插頭
立體搖擺對流掛牆扇
3D convection wall fan
ECO Sensor
人體感應器

4
Assembly
安裝
Function Setting
功能設定
安裝 /Installation
1. 按照掛牆扇掛座(01)背面掛孔，於牆壁上鑽孔四個，
將 掛牆扇 固定螺絲(02)插入掛牆扇掛座(01)掛孔，並
使用螺絲批把其裝上。
1. According to the hanging hole on the back of
the wall fan holder (01) , drill four holes on the
wall,insert the wall fan fixing screw (02) into
the wall fan holder's hanging hole (01) , and
install it with a screwdriver.
立體搖擺對流掛牆扇
3D convection wall fan
警告:掛牆扇支架必須安裝在混凝土或磚牆上。
請確認螺絲已完全鎖緊。
Caution: The wall fan holder must be installed
onto a Concrete or Brick wall.
Please confirm that the screws have
been totally tighten.
2. 確定掛牆扇掛座(01)已穩固裝上，即可將 掛牆扇 掛於掛牆扇掛座(01)上。
2. Hang the appliance well after confirm that the wall fan holder (01)
are firm.
向下插入
1. 將風扇擺放於穩固的平面上(或掛牆)，將插頭插入交流電壓220-240V~50-60Hz的獨立插座，
1. Place the Fan on a stable and flat surface. Plug the Power Cord into an 220-240V~
50-60Hz electrical outlet.
風扇可使用控制面板按鍵操控(如圖1)，或改用遙控器操控。
2. 開/關:按開/關鍵 ，風扇以第5段風速啟動。
2. POWER: Turn the Fan ON by pressing the key, the Fan start at speed 5.
The Fan may be operated by the control panel (as shown in Figure 1) or by your remote control.
(01)×01
(02)×04
圖1
Figure 1
定時 風速 左右送風
上下送風 送風模式 TIMER SPEED L/R OSCU/D OSC MODE
1H 2H 4H 6H
開/關
ON/OFF
ON TIMER
OFF TIMER
超強風速
GALE
風速/上調
SPEED/UP
風速/下調
SPEED/DOWN
左右送風 上下送風
L/R OSC U/D OSC
預約開機
ON TIMER
定時關機
OFF TIMER
人體感應
ECO SENSOR
搖擺/OSC
掛牆扇插槽
Wall Fan Slot

Function Setting
功能設定
5
3. 風速: 按風速(+) / (-)鍵，設定所需1至12段不同風速風速，LED顯示燈同時亮起。
按 鍵，風扇以超強風速運作約3分鐘，LED顯示燈同時亮起，之後會按
照之前設定的風速繼續運作。
3. S PEED: Press the (+)/(-) key to adjust the fan speed to the desired level (1 to12 level).
The speed setting is displayed on the LED light. Press the key to adjust
the wind speed to “Gale” level within 3 minutes, then it will continue to
operate at the previously set wind speed.
4. 搖擺送風: 按下搖擺送風鍵 ，風扇以自動左右搖擺模式送風。
按下搖擺送風鍵 兩次，風扇以自動上下搖擺模式送風。
按下搖擺送風鍵 三次，風扇以自動上下左右搖擺模式送風。
如欲停止自動上下左右搖擺送風，再按此鍵一次。
4. OSC: Press the key to allow the Fan to LEFT/RIGHT oscillate the wind direction.
Press the key twice to allow the Fan to UP/DOWN oscillate the wind direction.
Press the key three times to allow the Fan to LEFT/RIGHT & UP/DOWN
oscillate the wind direction.
To stop the oscillation, press the key again.
立體搖擺對流掛牆扇
3D convection wall fan
5. 定時關機: 在風扇運行時，按下定時設置鍵 ，選定4個不同的自動關機時間，分別
由1、2、4、6小時，LED定時設置顯示燈將會亮起，並會顯示所選關機時間。
5. OFF TIMER: When the Fan is running, pressing the key to set desired auto power
off time, There are 4 time intervals, from 1,2,4,6-hour. The LED of timer
will be on and displayed the off time setting.
6. 預約開機: 在待機模式下，按下定時設置鍵 ，選定4個不同的預約開機時間，分別
由1、2、4、6小時，LED顯示 屏 將會顯示所選開機時間及閃動，當LED顯
示 屏 閃動時，可同時設置搖擺送風、人體感應、及風速等功能。
6. PRESET START TIME: In Standby mode, pressing the key to set desired preset
power start time, There are 4 time intervals, from 1,2,4,6-
hour. The LED will be flash on and displayed the start time
setting on the LED screen. OSC, ECO SENSOR and SPEED can
be set at the same time when the LED indicator flashes.
***注意：當完成功能設定後15秒， LED顯示燈 會自動變喑。
Remarks: After settings, the LED indicator will change dumb automatically
after 15 seconds.

Function Setting
功能設定
6
7. 人體感應：按 鍵，‘Sensor’ 指示燈亮起，15秒後，風扇進入人體感應模式運作。
本機前方感應器會於機前約3米以內距離內感應是否有人體移動，若於一
分鐘內未能感應人體移動，本機會停止運作及進入待機狀態，原來亮著的
指示燈繼續亮起。當重新感應到有人體移動，本機會自動重新運作並會於
8小時後自動關機。若待機狀態持續12小時而未能感應任何人體移動，本
機會自動關機。
- 當左右搖擺時，感應器會於機前約3米以內距離及約90度內感應是否有
人體移動。
- 當上下搖擺時，感應器會於機前約3米以內距離及約35度內感應是否有
人體移動。
7. ECO SENSOR: Press the key, ‘Sensor’ indicator light will light on, about 15
seconds the Fan will enter the Eco Sensor mode. If no body movement
is detected for 1 minute, the Fan will stop working. The front sensor of
the machine will sense whether there is human movement within
about 3 meters in front of the machine, the Fan will work again
whenever it detects anybody movement and will automatically switch
off after 8 hours. If the Fan cannot detect any body movement after
12 hours,the Fan will switch off automatically.
- When using LEFT/RIGHT oscillate, the sensor will sense whether there
is a human body moving within about 3 meters in front of the
machine and within about 90 degrees.
- When using UP/RIGHT oscillate, the sensor will sense whether there
is a human body moving within about 3 meters in front of the
machine and within about 35 degrees.
左右方向
Left/Right
Direction
感應範圍
約3米以內
Sensing range
Within about
3 meters
約90度
About 90
degrees
約35度
About 35
degrees
上下方向
Up/Down
Direction
空置中
Vacant 空置中 Vacant
使用中
Using
停止運作
Stop working
若未能感應人體移動
於一分鐘內停止運作
Stop working within
1 minute if no body
movement
重新運作
Work again
立體搖擺對流掛牆扇
3D convection wall fan

Maintenance
清理及維護
Remote Control
遙控器
1.遙控器操作方式與機身按鍵操作方式相同。
2.更換電池 : 使用一枚3伏特鋰電池。
1. All functions performed by the Remote Control work are identical
to the Manual.
2. Battery replacement:Install one 3V Lithium battery.
警告
1)
2)
3)
4)
請把電池放在兒童碰不到的地方，如果孩子吞下電池，需立即致電咨詢醫生。
不要對電池進行充電或隨意棄置在有火源的地方。
應保持電池存放於乾燥，陰涼的地方。
以正確的方向插入電池。
電池的處理 - 請按相關地區的法律規定處理曾經使用的電池。
WARNING
1. Keep batteries out of reach of children. Should a child swallow a battery,
consult a doctor immediately.
2. Do not recharge or dispose in fire.
3. Keep in a dry and cool place.
4. Insert battery in rigdt direction.
Battery disposal - Please dispose the used battery per municipal or
provincial law.
7
警告：不使用風扇時，經常保持拔除電源，及切勿將風扇浸於水或其他液體中。在
清潔本風扇前，先將風扇關掉及把電源線從插座拔出。
House: Clean the outside of the Fan with a soft cloth, to remove presistent dirt or grime
wipe down with a cloth that has been dampened with warm soapy water.
注意：切勿使用含有腐蝕性的清潔劑或溶液清理風扇。
儲存：連同使用說明，把風扇存放於清涼及乾爽的地方。
WARNING: ALWAYS UNPLUG THE POWER CORD BEFORE MOVING OR SERVICING. DO NOT
IMMERSE THE FAN IN WATER! BEFORE CLEANING, MAKE SURE THAT THE UNIT HAS BEEN
SWITCHED OFF AND IT IS UNPLUGGED FROM THE MAIN OUTLET.
外殼：清理時切勿將風扇浸於水或其他液體中。使用濕潤軟布抹擦清潔，頑固污垢可用軟
布沾上含肥皂的溫水抹擦。
CAUTION: Do NOT use gasoline, benzene, thinner, harsh cleaners, etc., as they will damage
the Fan. NEVER use ALCOHOL or any other SOLVENTS.
STORAGE: Store the Fan with these instructions in the original box in a cool and dry place.
CF1519
3D Convection Wall Fan
立體搖擺對流掛牆扇
3D convection wall fan

8
Specification
技術規格
型號 Model Number
電源 Power Supply
額定功率 Rated Power
產品尺寸 Product Dimension
CF1519
220-240V~ 50-60Hz
20W
220 x 270 x 370 mm (約/Approx.)
Origin Map
源澤地圖
辦公時間
10:30am - 12:30pm (星期一至五)
02:30pm - 05:30pm (星期一至五)
10:30am - 12:30pm (星期六)
(星期日及公眾假期休息)
OFFICE HOURS
10:30am - 12:30pm (Mon to Fri)
02:30pm - 05:30pm (Mon to Fri)
10:30am - 12:30pm (Saturday)
(Closed on Sunday and Holiday)
立體搖擺對流掛牆扇
3D convection wall fan

立體搖擺對流掛牆扇
3D convection wall fan
產品保用証(一年自攜服務)
產品: 立體搖擺對流掛牆扇
型號: CF1519
此產品由購買日期起計算，本公司將根據下列條款及細則，提供一年保養服務(商業用享為3個月):
1. 於購買後一年內，經本公司技術員判斷為正常運作下損壞之產品，
可獲免費維修和/或零件更換。
2. 以下情況不被包括在保養範圍內：
-若產品是因為濫用、錯誤使用、疏忽及/或意外而遭致損壞；
-未經授權之自行處理、維修及/或改裝；
-任何搖控、機殼、掛牆扇掛座、固定螺絲、面蓋、扇葉，以及配件。
3. 需要檢查或維修時，請將產品送往本公司服務中心，並於修理妥當後自行取回。
4. 更換後之任何損壞零件，均屬本公司所有。
5. 本保養服務只適用於香港特別行政區。
6. 顧客必須同時出示零售商之正式發票，方可得到免費維修服務。
*** 額外3個月保用: 凡於購買產品後10天內完成網上登記，即可免費延長保用期3個月，即15個月免費保用(商業用途
除外)。請即登入網站: www.origo.hk
服務中心
源澤市務有限公司
香港新界葵涌青山公路403號(近華星街12號)匯城集團大廈21樓H室
電話: 2156 8238
www.origo.hk
Warranty Card(1 year carry-in)
Item : 3D Convection Wall Fan
Model : CF1519
Service Centre
ORIGIN MARKETING LIMITED
Unit H, 21/F., Reason Group Tower (nearby 12 Wah Sing Street), 403 Castle Peak Road,
Kwai Chung, N.T., Hong Kong.
Tel: [phone]
www.origo.hk
This product is warranted for 1year (commercial use for 3 months) from the date of purchase under the
following conditions:
1. For any defect, in the judgment of our technician, if it is caused under normal use, we are responsible for
repairing the product, and/or replacing parts at free of charge.
2. This warranty DOES NOT apply to:
- If the product has been damaged through abuse, misuse, negligence or accidents;
- Unauthorized repair, alteration/modification;
- The remote control, wall fan holder, fixing screw, housing, cover, blade or accessories.
3. The customer is requested to bring the unit to and from our Service Centre whenever
service is needed.
4. Any defective parts, which had been replaced, shall be of our property.
5. This warranty is valid in H.K.S.A.R. only.
6. Please show the Invoice to get free service.
***Extra 3 months warranty: just complete Online Warranty Registration within 10 days from the date of
receipt, free warranty will be extended to 15 months (not applicable to commercial use). Please enter our
website: www.origo.hk
www.origo.hk
www.origo.hk