ORiNG TGS-9200-M12-BP2 User manual

Quick Installation Guide
Version 2.0
Quick Installation Guide
Introduction
PRINTED ON RECYCLED PAPER
Q I G
ORing's Transporter series managed Ethernet switches are designed for
TM
industrial applicatio ns, such as rolling stock, vehicl e, and railway
applications. is managed Redundant Ring EthernetTGS-9200-M12-BP2
switch with 20x10/100/1000Base-T(X) ports which is specifically designed for
the toughest and fully compliant with EN50155 requirement. The switch
support Ethernet Redundancy protocol, O-Ring (recovery time < 30ms over
250 units of connection), O-Chain, MRP MSTP/RSTP/STP (IEEE*NOTE
802.1s/w/D) can protect your mission-critical applications from network
interruptions or temporary malfunctions with its fast recovery technology.
TGS-9200-M12-BP2 includes 2 sets of bypass ports that protect the network
from failures and Network maintenance by ensuring network integrity during
power loss. And support wide operating temperature from -40 C to 75 C.
o o
TGS-9200-M12-BP2 can also be managed centralized and convenient by
Open-Vision, Except the Web-based interface, Telnet and console (CLI)
configuration. Therefore, the switch is one of the most reliable choices for
EN50155 highly-managed Ethernet application.
Package Contents
Installation
Wall-mount
The device can be fixed to the wall. Follow the steps below to install the device on the wall.
Step 1: Hold the evice upright against the walld
Step 2: Insert four screws through the large opening of the keyhole-shaped apertures at the
top and bottom of the unit and fasten the screws to the wall with a screwdriver.
Step 3: Slide the evice downwards and tighten the four screws for added stability.d
The device is shipped with the following items. If any of these items is
missing or damaged, please contact your customer service representative
for assistance.
Preparation
Before you begin installing the device, make sure you have all of the package
contents available and a PC with Microsoft Internet Explorer 6.0 or later, for
using web-based system management tools.
Elevated Operating Ambient: If installed in a closed environment, make sure
the operating ambient temperature is compatible with the maximum
ambient temperature (Tma) specified by the manufacturer.
Reduced Air Flow: Make sure the amount of air flow required for safe operation
of the equipment is not compromised during installation.
Mechanical Loading: Make sure the mounting of the equipment is not in a
hazardous condition due to uneven mechanical loading.
Circuit Overloading: Consideration should be given to the connection of the
equipment to the supply circuit and the effect that overloading of the circuits
might have on overcurrent protection and supply wiring. Appropriate
consideration of equipment nameplate ratings should be used when addressing
this concern.
Safety & Warnings
For pin assignments of power, console and relay output ports, please refer to the following tables.
Contents
TGS-9200-M12-BP2
Pictures Number
1
CD 1
Panel Layouts
Front View
1. Reset button
2. Power1 status LED
3. Power2 status LED
4. R.M. status LED
5. Ring status LED
6. Fault LED
7. Power connector
8. Gigabit Ethernet ports
(G1 - G4 are bypass ports)
9. Link/ACT LED for Gigabit ports
10. Speed LED for Gigabit ports
11. Relay output
12. Console port
Wiring
Grounding
Grounding and wire routing help limit the effects of noise due to electromagnetic interference
(EMI). Run the ground connection from the grounding pin on the power connector to the grounding
surface prior to connecting devices.
Power port pinouts
The device supports two sets of power supplies and uses the M23 5-pin
female connector on the front panel for dual power inputs.
Step 1: Insert a power cable to the power connector on the device.
Step 2: Rotate the outer ring of the cable connector until a snug fit is
achieved. Make sure the connection is tight.
V1+
V1-
V2+
V2-
Relay output port pinouts
Relay N.C.
3A@24VDC
Network Connection
The switch has twenty 10/100/1000Base-T(X) Ethernet ports in the form of M12 connector.
Depending on the link type, the switch uses CAT 3, 4, 5,5e UTP cables to connect to network
devices (PCs, servers, switches, routers, or hubs). Please refer to the following table for cable
specifications.
TGS-9200-M12-BP2
TGS-9200-M12-BP2 1907-200-Q9200M1222-FX010
S w i tc h
E N 5 0 1 5 5
EN50155 20-port managed
Gigabit Ethernet switch
I N D U S T R I A L
1
Instead of screwing the screws in all the way, it is advised to
leave a space of about 2mm to allow room for sliding the
switch between the wall and the screws.
Cable Type Max. Length Connector
10BASE-T Cat. 3, 4, 5 100-ohm UTP 100 m (328 ft) 8-pin female M12
A-coding connector
100BASE-TX Cat. 5 100-ohm UTP UTP 100 m (328 ft) 8-pin female M12
A-coding connector
1000BASE-T Cat. 5/Cat. 5e 100-ohm UTP UTP 100 m (328 ft)
8-pin female M12
A-coding connector
For pin assignments of the Ethernet ports, please refer to the following tables.
QIG 1
11
12
7
4
5
6
7
8
21
3
4 5 62 3
8 10
9
8-Pin Gigabit Port Definition
PIN Definition
1 BI_DC+
2 BI_DD+
3 BI_DD-
4 BI_DA-
5 BI_DB+
6 BI_DA+
7 BI_DC-
8 BI_DB-
The switch uses the M12 A-coded 5-pin female connector
on the front panel for relay output. Use a cable with an M12
A-coded 5-pin male connector to connect the relay. The
relay contacts will detect user-configured events and form
an close circuit when an event is triggered.
Console port pinouts
N.C.
RXD
RS-23 2, 115200bps, 8, N , 1
GND
TXD
N.C.
Dimension
V1+
V1-
V2+
V2-
4
5
6
7
8
21
1B I_DC+
2B I_DD+
3B I_DD-
4B I_DA-
5B I_DB+
6B I_DA+
7B I_DC-
8B I_DB-
3
G1~G 20
Power
Failur e
Bypass
Power
Failur e
Bypass
Power
Failur e
Bypass
15
19.491.3
180
260
Unit =mm (Tolerance ±0.5mm)
216
LNK/ACT
Speed
LNK/ACT
Speed
LNK/ACT
Speed
LNK/ACT
Speed
G17
G18
G19
G20
G13
G14
G15
G16
FaultRingR.M.PWR2PWR1
Reset
3A@24V DC
Relay N. C.
Rela y Outpu t
Cons ole
RSVD
RXD
RS-232 , 115200 bps, 8, N , 1
GND
TXD
N.C.
Powe r G1
LNK/ACT
Speed
G2
LNK/ACT
Speed
G3
LNK/ACT
Speed
G4
LNK/ACT
Speed
G9
G10
G11
P12
G5
G6
G7
G8
TGS-9 200-M12-B P2
193.9
7.5
188.4
Ø5. 0
Ø8. 0
*NOTE : This function is available by request only
V1+
V1-
V2+
V2-
4
5
6
7
8
21
1 BI_D C+
2 BI_D D+
3 BI_D D-
4 BI_D A-
5 BI_D B+
6 BI_D A+
7 BI_D C-
8 BI_D B-
3
G1~ G20
Powe r
Fail ure
Bypa ss
Powe r
Fail ure
Bypa ss
Powe r
Fail ure
Bypa ss
LNK/ ACT
Spee d
LNK/ ACT
Spee d
LNK/ ACT
Spee d
LNK/ACT
Spee d
G17
G18
G19
G20
G13
G14
G15
G16
Faul tRingR.M.P WR2PWR1
Reset
3A@2 4VDC
Rela y N.C.
Rel ay Outp ut
Con sole
RSVD
RXD
RS-2 32, 1152 00bps , 8, N, 1
GND
TXD
N.C.
Pow er G1
LNK/ ACT
Spee d
G2
LNK/ ACT
Spee d
G3
LNK/ ACT
Spee d
G4
LNK/ ACT
Spee d
G9
G10
G11
P12
G5
G6
G7
G8
TGS -9200- M12-BP 2

Q I G Quick Installation Guide
PRINTED ON RECYCLED PAPER
Quick Installation Guide
Version 2.0
Q I G
Specifications
S w i tc h
E N 5 0 1 5 5
I N D U S T R I A L
1. Launch the Internet Explorer and type in IP address of the device. The default static
IP address is 192.168.10.1
Follow the steps below to log in and access the system:
2. Log in with default user name and password (both are ).admin
3. After logging in, you should see the following screen. For more information on
configurations, please refer to the user manual. For information on operating the device
using ORing’s Open-Vision management utility, please go to ORing website.
Resetting
To restore the device configurations back to the factory defaults, press the Reset
button for 5 seconds. Once the power indicator starts to flash, release the button.
The device will then reboot and return to factory defaults.
Configurations
Power
Redu nd ant Input Power Du al DC in pu ts. 12~48VDC on 5-pin M23 female connector
21W
Physical Chara cteristic
Enclosure IP-30
Dimension (W x D x H) 26 0(W) x 91.3(D) x 216(H) mm (10.24 x 3.59 x 8.50 in ch.)
Weight (g)
Environmenta l
-40 to 85 C (-40 to 185 F)
o o
Storage Temperature
5% t o 95 % Non-condensing
Operating Humidity
Regulatory App rovals
CE EMC (EN 55024, EN 55032), FCC Part 15B, EN 50155 (EN 50121-1, EN 50121-3-2)
EMC
EN 55024 (IEC/EN 61000-4-2 (ESD), IEC/EN 61000-4-3 (RS), IEC/EN 61000-4-4 (EFT),
IEC/EN 61000-4-5 (Surge), IEC/EN 61000-4-6 (CS), IEC/EN 61000-4-8(PFMF), IEC/EN 61000-4-11 (DIP))
EMS
IEC60068-2-27
Shock
IEC60068-2-31
IEC60068-2-6
Vibration
Free Fall
Warranty
5 ye ar s
EN60950-1
Safety
Fault Contact
Relay Relay output to carry capacity of 3A at 24VDC on M12 connector (5-pin M12 A-c od in g fe ma le)
Overload Current Protec ti on
Revers e Polarity P ro tection
Present
Present
-40 to 75 C (-40 to 167 F)
o o
Operating Tempe rature
ORing Switch Model
10/100/1000 Base-T(X ) Ports
in M12 Auto MDI/MDIX
Physical Ports
Technology
Ethernet Standard s
IEEE 802.3 for 10Base -T
IEEE 802.3u for 100Base -TX
IEEE 802.3ab for 1000 Ba se -T
IEEE 802.3x for Flow co nt rol
IEEE 802.3ad for LACP ( Li nk A ggregation Contro l Pr otocol)
IEEE 802.1p for COS (Cl as s of Service)
IEEE 802.1Q for VLAN Tagging
IEEE 802.1w for RSTP (Rapid Spa nn ing Tree Pr ot ocol)
IEEE 802.1s for MSTP (M ul tiple Spanning Tree Protocol)
IEEE 802.1x for Authent ic ation
IEEE 802.1AB for LLDP (Li nk L ay er D iscovery Protocol)
8K
MAC Table
8
Priority Queues
20 (8-pin fem ale A-coding with 2 x bypass function i ncluded)
Store-and-Forward
Processing
Sw itch Properties
Sw itching latency: 7 us
Sw itching bandwidth: 40 G bp s
Max. Number of Ava ilable VLANs: 4095
IGMP multicast grou ps : 128 for each VLA
Port rate limi ti ng: User Define
Security Features
Device Binding securi ty f eature
Enable/disable po rt s, MAC based port securit y
Port b as ed network access contr ol ( 802.1x)
VLAN (802.1Q) to segr eg ate and secure network traffi c
Radi us c entralized password manag em ent
SNMP v1/v2c/v3 encr yp ted authentication an d ac cess security
Https / SSH enhance network s ec urity
Software Fea tures
STP/RSTP/MSTP (IE EE 8 02.1D/w/s)
Redu nd ant Ring (O-Ring) wit h re cove ry t ime less than 30ms over 250 units
TOS/ Di ffserv supported
Quality of Service (802 .1 p) for real-time traffic
VLAN (802.1Q) with VLAN t ag ging and GVRP support ed
IGMP Snooping
IP-based bandwidt h ma nagement
Application-bas ed Q oS management
DOS/DDOS auto preventio n
Port c on figura tion, status, stati st ics, monitoring, se cu rity
DHCP Server/Client/Relay
SMTP Client
Modbus TCP
Network Redundancy
O-Ring
O-Chain
MRP*NOTE
MSTP (RSTP/STP comp at ible)
TGS-9200-M12-BP2
Up to 9.6K Bytes
Jumbo frame
RS-232 Serial Conso le Port RS-232 in 5-pin M12 female A-coding connector with console cable. 11 52 00 bp s, 8 , N, 1
Powe r Co nsumption(Typ.)
EN50155 20-port managed
Gigabit Ethernet switch
After installing the and connecting cables, he green power LEDswitch t
should turn on. Please refer to the following tablet for LED indication.
LED Color Status Description
PW1 Green On DC power module 1 activated
PW2 Green On DC power module 2 activated
R.M Green On Device operating in Ring Master mode
On Ring enabled
Ring Green Blinking Ring structure is broken
Fault Amber On Errors occur (i.e. power failure or port malfunctioning)
10/100/1000Base-T(X) Ethernet ports
On Port is linked
LNK/ACT Green Blinking Transmitting data
Green On Port is running at 1000Mbps
Amber On Port is running at 100Mbps
Speed
Green/Amber Off Port is running at 10Mbps
2495g
EN 55032, CISPR32, EN 61000-3-2, EN 61000-3-3, FCC Par t 15 B cl as s A
EMI
EN 50155 (IEC 61373)
Other
MTBF
20 5269.3131 hrs
*Note : This function is available by request only
ORing Industrial Networking Corp.
Copyright© 2014 ORing
All rights reserved.
TEL: [phone]
FAX: [phone]
Website: www.oringnet.com
E-mail: [e-mail]
TGS-9200-M12-BP2
TGS-9200-M12-BP2