ORiNG TGPS-9084GT-M12 User manual

Quick Installation Guide
Version 1.0
Quick Installation Guide
Introduction
PRINTED ON RECYCLED PAPER
QIG
The is a managed Gigabit Ethernet switch with 16
Gigabit PoE-enabled ports and 4 Gigabit non-PoE ports in M12 connector.
The series consists of -BP2 models (TGPS-9164GT-M12-BP2) and non-BP2
models (TGPS-9164GT-M12). The non-PoE ports of
provide bypass functions to ensure constant network connectivity
when power outage or node failure occurs. The switch supports various
Ethernet redundancy protocols such as O-Ring (recovery time < 30ms over
250 units of connection), Open-Ring, O-Chain, MRP and MSTP (RSTP/STP
compatible) to protect your mission-critical applications from network
interruptions or temporary malfunctions. With EN50155 compliance and M12
connectors, the device is a perfect choice for rolling stock applications.
TGPS-9164GT-M12 series
TGPS-9164GT-M12-
BP2
Package Contents
Installation
Wall-mount
The device can be fixed to the wall. Follow the steps below to install the device on the wall.
Hold the evice upright against the wall
Insert four screws through the large opening of the keyhole-shaped apertures at the
top and bottom of the unit and fasten the screws to the wall with a screwdriver.
Slide the evice downwards and tighten the four screws for added stability.
Step 1:
Step 2:
Step 3:
d
d
The device is shipped with the following items. If any of these items is
missing or damaged, please contact your customer service representative
for assistance.
Preparation
Before you begin installing the device, make sure you have all of the package
contents available and a PC with Microsoft Internet Explorer 6.0 or later, for
using web-based system management tools.
Elevated Operating Ambient:
Reduced Air Flow:
Mechanical Loading:
Circuit Overloading:
If installed in a closed environment, make sure
the operating ambient temperature is compatible with the maximum
ambient temperature (Tma) specified by the manufacturer.
Make sure the amount of air flow required for safe operation
of the equipment is not compromised during installation.
Make sure the mounting of the equipment is not in a
hazardous condition due to uneven mechanical loading.
Consideration should be given to the connection of the
equipment to the supply circuit and the effect that overloading of the circuits
might have on overcurrent protection and supply wiring. Appropriate
consideration of equipment nameplate ratings should be used when addressing
this concern.
Safety & Warnings
For pin assignments of power, console and relay output ports, please refer to the following tables.
Contents
TGPS-9164GT-M12/
TGPS-9164GT-M12-24V/
TGPS-9164GT-M12-BP2/
TGPS-9164GT-M12-BP2-24V
Pictures Number
1
CD 1
Dimension
Panel Layouts
Front View
1. Reset button
2. Power1 status LED
3. Power2 status LED
4. R.M. status LED
5. Ring status LED
6. Fault LED
7.
8. Non-PoE Gigabit Ethernet ports (with
bypass -BP2 model)
9. PoE-enabled Gigabit Ethernet ports
10.
15.
16.
Power connector
Link/ACT LED for non-PoE Gigabit ports
11. Speed LED for non-PoE Gigabit ports
12. Link/ACT LED for PoE-enabled Gigabit
ports
13. PoE indicator for PoE-enabled Gigabit
ports
14. Speed LED for PoE-enabled Gigabit ports
Console port
Relayoutputport
Wiring
Grounding
Grounding and wire routing help limit the effects of noise due to electromagnetic interference
(EMI). Run the ground connection from the grounding pin on the power connector to the grounding
surface prior to connecting devices.
Power port pinouts
The device supports two sets of power supplies and uses the M23 5-pin
female connector on the front panel for dual power inputs.
Insert a power cable to the power connector on the device.
Rotate the outer ring of the cable connector until a snug fit is
achieved. Make sure the connection is tight.
Step 1:
Step 2:
V1+
V1-
V2+
V2-
Relay output port pinouts
Relay N.C.
3A@24VDC
Network Connection
The switch has sixteen 10/100/1000Base-T(X) PoE and four 10/100/1000Base-T(X) non-PoE
Ethernet ports in the form of M12 connector. Depending on the link type, the switch uses CAT 3, 4,
5,5e UTP cables to connect to network devices (PCs, servers, switches, routers, or hubs). Please
refer to the following table for cable specifications.
TGPS-9164GT-M12 Series
TGPS-9164GT-M12 Series 1907-2-29-TGPS9164GTM12-1.0
Switch
EN50155
EN50155 20-port managed
Gigabit PoE Ethernet switch
INDUSTRIAL
1
Instead of screwing the screws in all the way, it is advised to
leave a space of about 2mm to allow room for sliding the
switch between the wall and the screws.
Cable Type Max. Length Connector
10BASE-T Cat. 3, 4, 5 1 00-ohm UTP 1 00 m (328 ft) 8-pin female M12
A-coding connector
100BASE-TX Cat. 5 100-ohm UTP UTP 100 m (328 ft) 8-pin female M12
A-coding connector
1000BASE-T Cat. 5/Cat. 5e 100-ohm UTP UTP 1 00 m (328 ft)
8-pin female M12
A-coding connector
For pin assignments of the Ethernet ports, please refer to the following tables.
QIG 116
15
7
14
12
13
4
5
6
7
8
21
3
45623
TGPS-9164GT-M12
FaultRingR.M.PWR2PWR1
Reset
3A@24VDC
Relay N.C.
Relay Output
Console
RSVD
RXD
RS-232,115200bps, 8, N, 1
GND
TXD
N.C.
Power G1
LNK/ACT
Speed
PoE
G2
LNK/ACT
Speed
PoE
G3
LNK/ACT
Speed
PoE
G4
LNK/ACT
Speed
PoE
G9
LNK/ACT
Speed
G10
LNK/ACT
Speed
G11
LNK/ACT
Speed
G12
LNK/ACT
Speed
G5
G6
G7
G8
V1+
V1-
V2+
V2-
PoE
PoE
PoE
PoE
4
5
6
7
8
21
1BI_DC+
2BI_DD+
3BI_DD-
4BI_DA-
5BI_DB+
6BI_DA+
7BI_DC-
8BI_DB-
3
G1~G4
1BI_DC+
2BI_DD+
3BI_DD-
4BI_DA-/PoEVout+
5BI_DB+/PoEVout-
6BI_DA+/PoEVout+
7BI_DC-
8BI_DB- / PoE Vout-
G5~G20
LNK/ACT
Speed
LNK/ACT
Speed
LNK/ACT
Speed
LNK/ACT
Speed
PoE
PoE
PoE
PoE
G17
G18
G19
G20
G13
G14
G15
G16
Power
Failure
Bypass
Power
Failure
Bypass
811
10
9
8-Pin Gigabit Non-PoE Port
Definition
PIN Definition
1BI_DC+
2BI_DD+
3BI_DD-
4BI_DA-
5BI_DB+
6BI_DA+
7BI_DC-
8BI_DB-
8-Pin Gigabit PoE Port
Definition
PIN Definition
1BI_DC+
2BI_DD+
3 BI_DD-
4BI_DA-withPoEVout+
5BI_DB+withPoEVout-
6 BI_DA+ with PoE Vo ut+
7 BI_DC-
8 BI_DB- with PoE Vout-
TGPS-9164GT-M12-BP2
FaultRingR.M.PWR2PWR1
Reset
3A@24VDC
Relay N.C.
RelayOutput
Console
RSVD
RXD
RS-232,115200bps,8, N, 1
GND
TXD
N.C.
Power G1
LNK/ACT
Speed
PoE
G2
LNK/ACT
Speed
PoE
G3
LNK/ACT
Speed
PoE
G4
LNK/ACT
Speed
PoE
G9
LNK/ACT
Speed
G10
LNK/ACT
Speed
G11
LNK/ACT
Speed
G12
LNK/ACT
Speed
G5
G6
G7
G8
V1+
V1-
V2+
V2-
PoE
PoE
PoE
PoE
4
5
6
7
8
21
1BI_DC+
2BI_DD+
3BI_DD-
4BI_DA-
5BI_DB+
6BI_DA+
7BI_DC-
8BI_DB-
3
G1~G4
1BI_DC+
2BI_DD+
3BI_DD-
4BI_DA- / PoE Vout+
5BI_DB+/ PoE Vout-
6BI_DA+/ PoE Vout+
7BI_DC-
8BI_DB-/ PoE Vout-
G5~G20
LNK/ACT
Speed
LNK/ACT
Speed
LNK/ACT
Speed
LNK/ACT
Speed
PoE
PoE
PoE
PoE
G17
G18
G19
G20
G13
G14
G15
G16
Power
Failure
Bypass
Power
Failure
Bypass
228
180
91.6
260
193.9
174.4
7.5
196.5
15.3
19.7
R2.5
R4
The switch uses the M12 A-coded 5-pin female connector
on the front panel for relay output. Use a cable with an M12
A-coded 5-pin male connector to connect the relay. The
relay contacts will detect user-configured events and form
an close circuit when an event is triggered.
Console port pinouts
N.C.
RXD
RS-232, 9600bps, 8, N, 1
GND
TXD
N.C.

QIG Quick Installation Guide
PRINTED ON RECYCLED PAPER
Quick Installation Guide
ORing Industrial Networking Corp.
Copyright© 2014 ORing
All rights reserved.
TEL: [phone]
FAX: [phone]
Website: www.oring-networking.com
E-mail: [email protected]
Version 1.0
QIG
Specifications
Switch
EN50155
INDUSTRIAL
1. Launch the Internet Explorer and type in IP address of the device. The default static
IP address is 192.168.10.1
Follow the steps below to log in and access the system:
2. Log in with default user name and password (both are ).admin
3. After logging in, you should see the following screen. For more information on
configurations, please refer to the user manual. For information on operating the device
using ORing’s Open-Vision management utility, please go to ORing website.
Resetting
To restore the device configurations back to the factory defaults, press the button for a
few seconds. Once the power indicator starts to flash, release the button. The device will then
reboot and return to factory defaults.
Reset
Configurations
Power
Redundant Input Power Dual DC inputs. 50~57VDC
on 5-pin M23 connector
20 Watts (power
consumption of P.S.E. is not
included)
Physical Characteristic
Enclosure IP-30
Dimension(WxDxH) 260(W) x 91.6(D) x 228(H) mm (10.24 x 3.60 x 8.98 inch.)
Weig ht ( g) 2528 g
Environmental
-40to85C(-40to185F)
oo
Storage Temperature
5% to 95% Non-condensing
Operating Humidity
Regulatory Approvals
FCC Part 15, CISPR (EN55022) class A, EN50155 (EN50121-3-2, EN55011, EN50121-4)
EMI
EN61000-4-2 (ESD), EN61000-4-3 (RS), EN61000-4-4 (EFT), EN61000-4-5 (Surge),
EN61000-4-6 (CS), EN61000-4-8, EN61000-4-11
EMS
IEC60068-2-27
Shock
IEC60068-2-32
IEC60068-2-6
Vibration
Free Fall
Warranty
5 years
EN60950-1
Safety
Fault Contact
Relay Relay output to carry capacity of 3A at 24VDC on M12 connector (5-pin M12 A-coding)
Overload Current Protection
Reverse Polarity Protection
Present
Present
-40to70C(-40to158F)
oo
Operating Temperature
ORing Switch Model
10/100/1000 Base-T(X) Ports
inM12AutoMDI/MDIXwith
P. S . E .
16xM12connector(8pinA-coding)
Physical Ports
Technology
Ethernet Standards
IEEE 802.3 for 10Base-T
IEEE 802.3u for 100Base-TX
IEEE 802.3ab for 1000Base-T
IEEE 802.3x for Flow control
IEEE 802.3ad for LACP (Link Aggregation Control Protocol)
IEEE 802.1p for COS (Class of Service)
IEEE 802.1Q for VLAN Tagging
IEEE 802.1w for RSTP (Rapid Spanning Tree Protocol)
IEEE 802.1s for MSTP (Multiple Spanning Tree Protocol)
IEEE 802.1x for Authentication
IEEE 802.1AB for LLDP (Link Layer Discovery Protocol)
IEEE 802.3at PoE specification
8K
MAC Table
8
Priority Queues
TGPS-9164GT-M12
10/100/1000Base-T(X) ports
in M12 4 x M12 connector (8-pin A-coding)
Store-and-Forward
Processing
Switch Properties
Switching latency: 7 us
Switching bandwidth: 40 Gbps
Max. Number of Available VLANs: 256
IGMP multicast groups: 128 for each VLA
Port rate limiting: User Define
Security Features
Device Binding security feature
Enable/disable ports, MAC based port security
Port based network access control (802.1x)
VLAN (802.1Q) to segregate and secure network traffic
Radius centralized password management
SNMP v1/v2c/v3 encrypted authentication and access security
Https / SSH enhance network security
Software Features
STP/RSTP/MSTP (IEEE 802.1D/w/s)
Redundant Ring (O-Ring) with recovery time less than 10ms over 250units
TOS/Diffserv supported
Quality of Service (802.1p) for real-time traffic
VLAN (802.1Q) with VLAN tagging and GVRP supported
IGMP Snooping for multicast filtering
Port configuration, status, statistics, monitoring, security
SNTP for synchronizing of clocks over network
Support PTP Client (Precision Time Protocol) clock synchronization
DHCP Server / Client support
Port Trunk support
MVR (Multicast VLAN Registration) support
Modbus TCP
Network Redundancy
O-Ring
Open-Ring
O-Chain
MRP
STP/RSTP/MSTP
Warning / Monitoring System
Relay output for fault event alarming
Syslog server / client to record and view events
Include SMTP for event warning notification via email
Event selection support
PoE Output Power
TGPS-9164GT-M12-24V TGPS-9164GT-M12-BP2 TGPS-9164GT-M12-BP2
-24V
4 x M12 connector (8-pin A-coding with 2 x
bypass function included)
Up to 9.6K Bytes
Jumbo frame
RS-232 Serial Console Port RS-232 in M12 (5-pin M12 A-coding) connector with console cable. 115200bps, 8, N, 1
Dual DC inputs. 24 (12~57)
VDC on 5-pin M23 connector
Dual DC inputs. 50~57VDC
on 5-pin M23 connector
Dual DC inputs. 24 (12~57)
VDC on 5-pin M23 connector
Power Consumption(Typ.)
25 Watts (power
consumption of P.S.E. is not
included)
20 Watts (power
consumption of P.S.E. is not
included)
25 Watts (power
consumption of P.S.E. is not
included)
480 Watts 120 Wattts (12~24 VDC)
240 Watts (24~57 VDC) 480 Watts 120 Wattts (12~24 VDC) 240 Watts (24~57 VDC)
2553 g 2550 g 2575 g
TGPS-9164GT-M12 Series
TGPS-9164GT-M12 Series
EN50155 20-port managed
Gigabit PoE Ethernet switch
After installing the and connecting cables, he green power LED
should turn on. Please refer to the following tablet for LED indication.
switch t
LED Color Status Descr iption
PW1 Green On DC power modul e 1 activ ated
PW2 Green On DC power modul e 2 activ ated
R.M Green On Device oper ating in Ring Master mod e
On Ring enabled
Ring G reen Blin king Ring structure i s brok en
Fault Amber On Errors occur (i.e. power failure or por t malfunctioning)
10/100/ 1000Base-T( X) P.S.E Eth ernet po rts
On Port is linked
LNK/AC T Green
Blinking Transmitting data
PoE Green On Power supplied over Etherne t
Green On Port is r unning at 1000Mbps
Amber On Port is r unni ng at 100MbpsSpeed
Green/ Amber Off Port is runni ng at 1 0Mbps
10/100/ 1000Base-T( X) Ethernet por ts
On Port is linked
LNK/AC T Green
Blinking Transmitting data
Green On Port is r unning at 1000Mbps
Amber On Port is r unni ng at 100Mbps
Speed
Green/ Amber Off Port is runni ng at 1 0Mbps