ORiNG RES-9242GC User manual

Quick Installation Guide
Version 1.0
Quick Installation Guide
Introduction
PRINTED ON RECYCLED PAPER
QIG RES-9242GC
1907-2-29-RES9242GC-1.0
The is a rackmount managed Ethernet switch designed for
industrial applications, such as rolling stock, vehicle, and railway
applications. Featuring twenty-four 10/100Base-T(X) ports and two Gigabit
combo ports, the device is able to meet the needs for high port density and
high-speed, long-distance transmission. With complete support for Ethernet
redundancy protocols such as O-Ring (recovery time < 30ms over 250 units of
connection) and MSTP (RSTP/STP compatible), the series can protect your
mission-critical applications from network interruptions or temporary
malfunctions with its fast recovery technology. Featuring a wide operating
temperature from -40 C to 75 C, the device can be managed centrally and
conveniently via Open-Vision, web browsers, Telnet and console (CLI)
configuration, making it one of the most reliable choice for highly-managed
and Fiber Ethernet power substation and rolling stock application.
RES-9242GC
oo Dimension
Panel Layouts
1
1. Console port
2. Reset button
3. Power indicator
4. Ring status LED
5. R.M status LED
Package Contents
Contents
QIG
CD
Console Cable
RES-9242GC
Rack-mounted
kit (L&R)
Pictures Number
X1
X1
X1
X1
X1
Front View
Rear View
Installation
Rack-mounting
Step 1:
Step 2:
Install left and right front mounting brackets to the switch using 4 M3 screws on each side.
With front brackets orientated in front of the rack, fasten the brackets to the rack using
two more screws.
Network Connection
Wiring
RES-9242GC Rack Mount Managed Ethernet Switch
The device is shipped with the following items. If any of these items is missing
or damaged, please contact your customer service representative for
assistance.
Preparation
Before you begin installing the switch, make sure you have all of the package
contents available and a PC with Microsoft Internet Explorer 6.0 or later, for
using web-based system management tools.
Elevated Operating Ambient:
Reduced Air Flow:
If installed in a closed or multi-unit rack
assembly, the operating ambient temperature of the rack environment may be
greater than room ambient. Therefore, consideration should be given to
installing the equipment in an environment compatible with the maximum
ambient temperature (Tma) specified by the manufacturer.
Installation of the equipment in a rack should be such
that the amount of air flow required for safe operation of the equipment is
not compromised.
Safety & Warnings
6. Fault LED
7. Link/ACT LED for Ethernet ports and Combo ports
8. Speed LED for Ethernet ports and Combo ports
9. LAN ports
10. Combo ports
1. Ground screw
2. AC power input (100V~240V / 50~60Hz)
The device comes with standard Ethernet ports. According to the link type, the switch uses CAT 3,
4, 5,5e UTP cables to connect to any other network devices (PCs, servers, switches, routers, or
hubs). Please refer to the following table for cable specifications.
Cable Types and Specifications:
Power Cable X2
SWITCH
MANAGED
Rack-Mount
Mechanical Loading:
Circuit Overloading:
Mounting of the equipment in the rack should be such that a
hazardous condition is not achieved due to uneven mechanical loading.
Consideration should be given to the connection of the equipment
to the supply circuit and the effect that overloading of the circuits might have on
overcurrent protection and supply wiring. Appropriate consideration of equipment
nameplate ratings should be used when addressing this concern.
RES-9242GC
G1 1000M G2
Fault
Reset
LNK
ACT
LNK
ACT
Console
115200bps,8,N,1
RES-9242GC
G1 1000M G2
Fault
Reset
LNK
ACT
LNK
ACT
Console
115200bps,8,N,1
2 3 45
6
8
7
910
1 2
Cable Type Max. Length Connector
10BASE-T Cat. 3, 4, 5 100-ohm UTP 100 m (3 28 ft) RJ-45
100BASE-TX Cat. 5 100-ohm UTP UTP 100 m (328 ft) RJ-45
1000BASE- T Cat. 5/Cat. 5e 100- ohm UTP UTP 100 m (3 28ft) RJ-45
For pin assignment, please refer to the following tables.
10/100Base-T(X) RJ -45 Port Pin Assignments
Pin No. Assignment
1TD+
2TD-
3RD+
6RD-
10/100Base-T(X) MDI/MDI-X Pin Ass ignments
Pin No. MDI por t MDI-X port
1 TD+(transmit) RD +(recei ve)
2 TD -(transmit) RD- (receive)
3 RD+(receive) TD+(transmit)
4Notused Notused
5Notused Notused
6 RD-(receive ) TD-(transmit)
7Notused Notused
8Notused Notused
1000Base-T MDI/MDI-X Pin Assignments
Pin No. MDI port MDI-X port
1BI_DA+BI_DB+
2 BI_DA- BI_DB-
3 BI_DB+ BI_DA+
4 BI_DC+ BI_DD+
5 BI _DC- BI_DD-
6 BI_DB- BI_DA-
7 BI_DD+ BI_ DC+
8 BI_ DD- BI_ DC-
AC Power Connection
The device can be powered by AC electricity. Simply insert the AC power cable to the power
connector at the back of the switch and turn on the power switch. The input voltage is 100V~240V /
50~60Hz.
Grounding
The device provides grounding and wire routing to help limit the effects of noise due to
electromagnetic interference (EMI). Run the ground connection from the ground screws to the
grounding surface prior to connecting devices.
RS-232 Console Port Wiring
The device can be managed via the console port using a RS-232 cable which can be found in the
package. Connect each end of the RS-232 cable to the switch and a PC respectively.

Quick Installation Guide
Quick Installation Guide
Version 1.0
Configurations
After installing the switch and connecting cables, the green power LED
should turn on.
2. Log in with default user name and password (both are ). After logging in, you should see the
following screen. For more information on configurations, please refer to the user manual. For
information on operating the switch using ORing’s Open-Vision management utility, please go to ORing
website.
admin
Specifications
Technology
Ethernet Standards
IEEE 802.3 for 10Base-T
IEEE 802.3u for 100Base-TX and 100Base-FX
IEEE 802.3ab for 1000Base-T
IEEE 802.3z for 1000Base-X
IEEE 802.3x for Flow control
IEEE 802.3ad for LACP (Link Aggregation Control Protocol)
IEEE 802.1p for COS (Class of Service)
IEEE 802.1Q for VLAN Tagging
IEEE 802.1w for RSTP (Rapid Spanning Tree Protocol)
IEEE 802.1s for MSTP (Multiple Spanning Tree Protocol)
IEEE 802.1x for Authentication
IEEE 802.1AB for LLDP (Link Layer Discovery Protocol)
Power
Input power
Power consumption (Max) 15.2W
Overload current protection
Physical Characteristic
Dimension(WxDxH)
Weig ht (g )
8K
MAC Table
8
Priority Queues
Store-and-Forward
Processing
Switching latency: 7 us
Switching bandwidth: 8.8Gbps
Max. Number of Available VLANs: 4095
VLAN ID Range : VID 1 to 4094
IGMP multicast groups: 256 for each VLAN
Port rate limiting: User Define
Switch Properties
Device Binding security feature
Enable/disable ports, MAC based port security
Port based network access control (802.1x)
Single 802.1x and Multiple 802.1x
MAC-based authentication
QoS assignment
MAC address limit
TACACS+
VLAN (802.1Q ) to segregate and secure network traffic
Radius centralized password management
SNMP v1/v2c/v3 encrypted authentication and access security
Https / SSH enhance network security
Web and CLI authentication and authorization
Security Features
IEEE 1588v2 clock synchronization
IEEE 802.1D Bridge, auto MAC address learning/aging and MAC address (static)
Multiple Registration Protocol (MRP)
MSTP (RSTP/STP compatible)
Redundant Ring (O-Ring) with recovery time less than 10ms over 250 units
TOS/Diffserv supported
Quality of Service (802.1p) for real-time traffic
VLAN (802.1Q) with VLAN tagging and GVRP supported
IGMP Snooping for multicast filtering
IP-based bandwidth management
Application-based QoS management
DOS/DDOS auto prevention
Port configuration, status, statistics, monitoring, security
DHCP Client/Server
DHCP Relay
Modbus TCP
SMTP Client
NTP server
Software Features
O-Ring
Open-Ring
O-Chain
MRP
MSTP (RSTP/STP compatible)
Fast Recovery
Network Redundancy
Environmental
-40to85C(-40to185F)
oo
Operating Temperature
5% to 95% Non-condensing
Operating Humidity
Regulatory Approvals
FCC Part 15, CISPR (EN55022) class A
EMI
EN61000-4-2 (ESD),
EN61000-4-3 (RS),
EN61000-4-4 (EFT),
EN61000-4-5 (Surge),
EN61000-4-6 (CS),
EN61000-4-8,
EN61000-4-11
EMS
Warranty
5 years
Dual 100~240VAC power inputs
Present
2695 g
440x200x44mm(17.32x7.87x1.73inch)
ORing Switch Model RES-9242GC
Physical Ports
10/100Base-T(X) Ports in RJ45
Auto MDI/MDIX 24
-40to75C(-40to167F)
oo
Storage Temperature
ORing Industrial Networking Corp.
Copyright© 2016 ORing
All rights reserved.
TEL: [phone]
FAX: [phone]
Website: www.oring-networking.com
E-mail: [email protected]
PC pin out (male) assignment RS-232 w ith DB9 fem ale connector DB9 to RJ 45
Pin #2 RD Pin #2 TD Pin #2
Pin #3 TD Pin #3 RD Pi n #3
Pin #5 GD Pin #5 GD Pin #5
SFP
The switch comes with two combo ports which include a SFP port that can connect to
other devices using SFP modules. The SFP modules are hot-swappable input/output
devices that can be plugged into the SFP ports to connect the switch with the fiber-
optic network. Remember that the TX port of Switch Ashould be connected to the RX
port of Switch B.
Fiber
Switch-A Switch-B
LED Col or Status Descript ion
PWR Green On System power is on
R.M Green On Port is o perated as Ring Master.
Ring Green On Port is operated in Ring mode
Faul t Amber On Errors occur (power f ail ure or port malfunctioning )
10/100Base-T(X) RJ45 port
Link/ACT Green On Port is connected
On Port is runni ng at 100Mbps
Speed Amber Off Port is runni ng at 10Mbps
10/100/ 1000Base-T(X) RJ45 por t with Combo port
Link/ACT Green On Port is connected
On Port is runni ng at 1000Mbps
Speed Amber
Off Port is runni ng at 10/100Mbps
100/1GBase-X SFP port wit h Combo port
Link/ACT Green On Port is connected
1. Launch the Internet Explorer and type in IP address of the switch. The default static
IP address is 192.168.10.1
Resetting
To reboot the switch, press the Reset button for 2-3 seconds.
To restore the switch configurations back to the factory defaults, press the Reset button for 5
seconds.
10/100/1000Base-T(X) RJ45
and 100/1000Base-X SFP with
combo port
2
QIG RES-9242GC
1907-2-29-RES9242GC-1.0
RES-9242GC Rack Mount Managed Ethernet Switch
SWITCH
MANAGED
Rack-Mount
RS-232 Serial Console Port RS-232 in DB-9 connector with console cable. 115200bps, 8, N, 1
Enclosure 19 inches rack mountable
IEC60068-2-27
Shock
IEC60068-2-32
Free Fall
IEC60068-2-6
Vibration
EN60950-1 (compliant, certification, pending)
Safety