ORVIS CFO User manual

THE ORVIS COMPANY | MANCHESTER VERMONT 05254 | www.orvis.com
Orvis Technical Questions: [email protected] or 800-778-4778
INTRODUCTION
Updating a classic, the CFO tastefully blends modern perfor-
mance-enhancing design and technology under a traditional-looking
skin. Features include:
• Two internal radial stainless steel reel bearings.
• Line guard is machined into the reel cage.
• Modified machined design is lighter.
• Impregnated wood handle.
• Brown/bronze anodized matte finish.
• Disc drag.
DRAG OPERATION
Orvis CFO Disc Reels feature an adjustable
disc drag system.The pressure exerted on the disc
determines the drag pressure and may be adjusted
by turning the drag adjustment knob located on
the back of the reel frame.
To increase the drag, turn the drag adjustment
knob (figure 1) clockwise. To decrease it, turn the
knob counterclockwise. Sufficient drag pressure
must always be applied when fighting a fish to pre-
vent line overrun. Additional drag may be applied
by palming the spool rim with you fingertips or
palm.
SPOOL REMOVAL
The spool release latch is located in the middle
of the reel spool.To remove the spool, depress the
spool release latch (figure 2) while lifting the spool
out of the reel frame.
CONVERTING TO RIGHT-HAND
RETRIEVE
Your new CFO Reel has the drag pawl factory-
installed for left-hand wind.
To change your CFO Reel to right-hand wind,
depress the spool latch release and remove the
spool. On the backside of the spool, you will see a
spool gear that has three screws fastening it to the
spool.
1. Remove the three clutch screws then remove
the spool gear from the spool.
2. Find the clutch bearing. It will either be
inside the spool gear or still on the spool (fig-
ure 3).
• If the bearing stays with the gear upon
removal, use a small screwdriver to push the
bearing out.
• If the bearing was in the spool upon removal of the spool gear,
use a pair of pliers to remove it from the spool.
3. Remove the bearing, flip it over, and replace it in the the spool
gear.
4. Replace spool gear with the three clutch screws.
5. After you have reassembled the spool gear, remove the click
pawl, flip it over, and replace it on the reel frame to complete
the conversion.
ROUTINE MAINTENANCE
Your new Orvis CFO reel has been properly lubricated prior to ship-
ping. However, it should be cleaned and lubricated after extensive use
or after contact with dirt, sand, or saltwater.Your reel should receive rou-
tine cleaning and maintenance at least twice each year. Lightly lubricate
all moving components—handle, center spindle, and gear shaft with Penn
reel lube, available in tackle shops. After lubrication, check screws for
proper tightness. Do not put the reel away wet, or into a wet reel case or
tackle box.
Following use in saltwater, the reel should be rinsed in fresh water and
all parts, except drag surfaces, lightly oiled.The body and spool should be
wiped with a lightly oiled cloth.
For extended storage, remove both line and backing and loosen the
drag.
QUESTIONS?
If you have any questions about the operation and maintenance of
your new reel, Orvis Technical Advisors are always available. Email: info@
orvis.com. Phone: [phone].
GUARANTEE
Your Orvis CFO reel is unconditionally guaranteed against defects
in materials and workmanship.
If you have any problems, simply send your reel and a $10 check to
the following address:
By USPS Mail: Orvis Reel Service; PO Box 798; Manchester,VT
05254.
By FedEx or UPS : Orvis Reel Service;Tennis Way, Rt. 7A; East
Dorset,VT 05253.
If the reel is in any way defective in material or workmanship,
your $10 repair check will be returned to you at once.
Your reel will be completely serviced (cleaned, lubricated, and
returned to you postpaid) for a fee of $10, plus cost of parts.
Damaged reels can be repaired on an individual basis and repair
work will be billed at the hourly shop rate, plus parts. We will pro-
vide a written estimate upon receipt of the reel prior to any work
being done.
CFO
Figure 1
Figure 2
Figure 3

THE ORVIS COMPANY | MANCHESTER VERMONT 05254 | www.orvis.com
Orvis Technical Questions: [e-mail] or 800-778-4778
CFO
REEL ASSEMBLY
1 Drag Screw
2 Drag Nut
3 Drag Washer
4 Drag Knob
5 Spindle Cap
6 Reel Body
7 Reel Foot Screws
8 Reel Foot
9 Clicker Retainer
10 Clutch Gear
11 Rulon Drag Washer
12 Drag Gear
13 Rulon Drag Washer
14 Drag Gear Cap
15 Clicker Pawl
16 Clicker Spring
17 Spindle
18 Spool Release Screws
19 Spool Release Cap
20 Spool Release Washer
21 Spool Release Clip
22 Spool Release Spring
23 Spool Release Pin
24 Handle Knob Spindle
Screw
25 Handle Knob
26 Handle Knob Retainer
27 Counter Weight
28 Spool
29 Counter Weight Screw
30 Radial Bearings
31 Spindle Spacer
32 Clutch Retainer
33 One-Way Clutch Bearing
34 Clutch Retainer
35 Spool Gear
36 Spool Gear Screws
CFO Reel Specifications
Capacity in Yards
Stated capacities are based on Orvis 20-lb. Dacron®backing and a 90-ft
weight forward floating fly line. If a double taper fly line is desired, deduct
50 yards from stated capacities.
WF1 100 yds
WF275 125 yds
WF350 100
WF475 75 yds
WF550
WF625
I II III
LINE WEIGHT
CFO DISC DRAG FLY REELS
Capacity Chart
CFO I weight: 31⁄2oz. | CFO II weight: 35⁄8oz. | CFO III weight: 37⁄8oz.
2134
5
6
7
10
11 13 1412
8
916
17
18
192021
15
22
23
242526
27
28
29
3030323334
35
36
31