OSI CO E1 User manual


1

E110628E(I)

To our Users:
If you do not have the tools or are unaccustomed to the
installation, or
you are not sure about whether any base
exists on ceiling or wall, or when installing this product
ona concrete wall, ask the professional installer.

About the professional installer, ask your dealer or
us.
Professional installers that have contracted fo
r the
installation should submit this manual together with
the instruction manual.
E1 Electric Screen
Thank you for your purchase.
■Ensure that you read this installation and instruction
manual carefully and use the screen correctly.
Be sureto retain the manuals for future reference.
Index
SafetyPrecautions・・・・・・・・・・ 2〜4
Accessories ・・・・・・・・・・・・・・ 5
Construction &Parts name ・・・・・・・ 6
Cautions in installation・・・・・・・・   7
InstallationGuideline ・・・・・・・ 8〜9
Fitting IR receiver & power cable ・・ ・10
Cautions: operationofscreen ・・・・ 11
Limit SwitchSetting ・・・・ 12〜15
Q&A ・・・・・・・・・・16
Specifications ・・・・・・・・・・・17〜18


2

E110628E(I)

Pull out thepowerplug, whensmoke, heat, smellor strange noisehappens.
The continuoususe maycause a fire and an electric shock.
Confirmthe load ofthescreen can be sustained.
Ifthe load is not enough, the screen may fall offand cause harm.
Confirmthe strength of installationplace forthe long use of the screen
Ifthe strength is not enough, the screenmay fall off andcause harm.
Important Safety Instructions
Ensure you follow the below instructions for safety.
Donot damagethepowercableandplug.
(Do not damage, process, twist, p
ull, put a heavy item on, bring close to the high temperature or
bundle the power cord.)
It causes the electric shock, the short, and a fire when used with damage.
Makesurethepowerplugisinsertedtightly.
When insertion is not enough, it maycause a fire bythe electric shock and heat.
This indicates that failure to follow these safety precautions could result in

death or serious injury.
This indicates that failureto followthese safetyprecautionscould result in
bodily injuryor damage to property.
This manual explains the necessary precautions to pr
event the harm to the user or the others and any
damageto property.
■The marks show the level of harm and damage caused by the mal-handling
or the disregard to the
precautions.
■These marksexplain theprecautioncontents.

Prohibition : youare prohibited to do so.
Force : you are forced not to do so.
WARNING
WARNING
CAUTION


3

E110628E(I)

Donot operatethepowerplug with awet hand.
It maycause an electric shock.
Stop using, when anything like metal, water, orliquid goesintothe screen, and pull out the
powerplug.
The continuoususe maycause a fire and an electric shock.
Takethepowerplugtoconnect,not the powercable.
It maydamage thepower cable and cause a fire and an electricshock.
Do not disassemble, repair and/or modify the screen.
The screen may fall out. Please consult your dealer for repair.
Donot touchthepowerplug when thundering.
It maycause an electric shock.
Do not hang fromthe screen orsuspend anything to it.
It may damage the main unit or screen fabric with danger.
W
ARNING


4

E110628E(I)

Do not pull out the screen morethan the STOP labelpoint.
The screen fabric mayfallout.
Donot putanything orfragilethingbelowthescreen.
Anything could block the movement ofthe screen causing damage.
Donot use thesharpcutleryorpointed metalnearthe screen.
It might damage the screenfabric.
Do not forcefully pullout the screen.
The main unit or screen fabric may fall out.
■ We are not responsible for the accidentsor damages caused by mal-handlings and natural
disasters, etc
CAUTION


5

E110628E(I)

Please confirmthe accessories before installation.
The p
artsand tools are subject to change according to the installation places
and mounting methods.
Accessories
Hexagonalspanner x1
Hexagonalspanner x1
(nominal 4for limit adjustment)    (nominal 3 for mounting bracket)
Infrared remote controller x1 AAA drybatteriesx2 Infrared receiver x1Sparesticker x1
Mountingbracketsx2
Stoppersx2
 

Bolts
(M4x10)x4
Screw
(4x40)x4
Washer
(M4)x4


6

E110628E(I)

Construction &Parts name
The screen is composed of parts as below. Please confirm before installation
Power Supply(Left)
     
UP
button to store the screen.
Refer to page 9.
STOP
button to stopthe screen.
Refer to page 8-9

DOWN
button to use the screen.
Refer to page 8.
Screen Fabric
Mounting bracket
Infrared remote controller
Screenmain unit
STOP label
Ifthe screenfabric is pulled
downmore thanthe STOP
label, it maycausethe
fall-out or reverse rolling.
Do not pullout the screen
more thanthe STOP label
point.
Under pipe
STOP Label
Infrared receiver
Refertopage 7
Operating switch(on left side)
Input (large)
for FS-1(Option)
Input
(small) for
Infraredreceiver
Case
Adjustment knob


7

E110628E(I)

Cautions in installation
■Do not installthe screento such placesto avoid malfunctioning and troubles.
Placewhere vibrationand impact might apply.
Place where heat, steam, and oil or smoke generates.
Placewherewind of heating apparatuscomes
■Please check the structure and materialofthe mounting place before installation.
■Make sureto put a blanket or soft cloth before installationto avoid anydamageto theproduct orthe floor.
■Make suretotighten the screws.
■Payattentiontothe environment for safetyin installation.
In installing the screen, make sure that the wall or ceiling is strong enough
tokeepthe screen weight for long time. Reinforcement is necessaryto mount
the screenongypsumor particleboard. If the strength is not enough, it maycause
the falloffofthe screen.
WARNING


8

E110628E(I)

[Introduction] Please note allthe parts have thedetermined mounting area and direction. Followthe instructions
and drawings in this manual before installation.


1. Checking the mounting area            
This product canbe installedona ceiling orwall. Checkthe installation locationbefore installing. Inorder to
mount the bracket to basewood in aceiling or wall withscrews, push the “detection needle” into theceiling
or wall and locate base wood.
Ifbasewood cannot be found, ask a professionalinstaller to mount the product.

2.Attaching the mounting brackets
Mount the brackets to the ceiling or wall with the attached screws.
(1) Mount the brackets in parallel.
(2) For the distance betweenthe two brackets, refer to the G dimensions in “Specifications”.

■ Ceiling              ■ Wall

Tool: Phillips screwdriver
When installing this product, tightenthe attached screws into base wood
with more than 20 mmthickness in the ceiling orwall. Ifthe base
wood is insufficiently thick and the screwsare not tight enough, they
mayfallout.
Installation Guideline
Base
wood
Base
wood
WARNING


9

E110628E(I)

3.Mounting the main unit
１）Fit the mounting bracket into the groove of
the screen case and then push the case
horizontally in the direction of the arrow so that
the fixed spring hooks in withthe click sound










２）Usetheattached bolts to fix the stopper(Use the attached hexagonalspanner)





















３）After mounting, pullthe screen caseto verifythat it will not remove.
Mounting bracket
Fixedspring
Bolts（M4×10）
Stopper
Case
Ensurethescreencase and mounting bracketsare fitted.
Failure to do so may cause the screen to fall out. It may cause damage to the
product and the environment.

○Correct




×Wrong
WARNING


10

E110628E(I)

Fitting the IR receiver and power cable
1) Connect the plug ofthe Infrared receiver(the cable lengthis 300mm) tothe input (small) located at the left
cap ofthe case.
2) Remove the dust, water, oil and moist onthe location, and stickthe Infrared receiver tightly, peeling the
coated paper off. The location should be where the signalofthe infrared remote controller canreach.
Avoidthe direct sunshine area.
3) Put the plugofthe Power cable tothe main.
Reminder:
When the reception is weak becauseofthe direct sunshine, the infrared receiver location should
be changed
There are locations wherethe infrared receiver cannot be stuck.
Usethe spare sticker, whenthe adhesive power ofthe pad is weak.
WARNING Make sure the power plug is inserted tightly.
When insertion is not enough, it maycause a fire bythe electric shock and
heat.
For those userswho use FS-1, please refer to the instruction manualof FS-1.
FS-1 should be connectedtothe input (large).
WARNING Plug in the IRreceiver plug tightly. If not, it may cause mal-functioning.
3)
1)
2)


11

E110628E(I)

CAUTION : operations of screen
■Be careful inrepeating the screen going up and down.
●The continuous use ofthe up and downoperations maycause the heat prevention circuitrywork, and stop the
screen.
When this happens, pleaseoperate after some time (15 – 20 minutes) for cooling off.
This is not the breakdown.
Changing the automatic stop positions (Projection & stored positions)
■Please read carefullybeforechanging.
The automatic stop positions are pre-set at factorybeforeshipment. Please follow the following instructions when
changes are necessary.
●UP position (Stored position): The maximum upper position is pre-set at factory.
For the changes, select the position belowthe pre-set.
●DOWN position(Projection position): The maximum lower position is pres-set at factory.
For the changes, select the position upper thanthe pres-set.

If the stop position is set upper the maximum position by mistake, the screen
digs into to the case, and the fabric is pulled causing the breakdown and
wrinkles.
Ifthe stop position is set below the pre-
set, the fabric might fall off or roll back
reversely, causing wrinkles.
CAUTION
CAUTION


12

E110628E(I)

Limit switchsetting
■Change of【U P】position    It should be below the pre-set position.
Take offthe whitecover forthe limit adjustment hole.
Confirmthe adjustment volume.
Make sure the screen is set at UP (Stored) position before adjustment.











Put the hexagonal spanner into the limit adjustment hole, and turn the adjustment volume clock wise.
Gradual adjustments recommended not exceeding the screendown position.

■ Turndirection

1 turn makesthe screen drop appox. 30mm.
Ref. 1/2 turn: approx. 15mm
※ Remember the times ofturnuntil the final confirmation of the
UP position.



         ②    ①

① After adjustment, push the DOWN button of the IR remote
controller. When the screen is drawn approx. 20-30cm,
push the STOP button.
② Push UP button and confirm whether the screen stops at the
desired position.
Seen fromthe front
Seen from below
Preset
Position⇒
UP
Desired
position⇒
UP
Adjustmentvolume
Upper limit(Stored)
Insidethecase
Limit adjustment hole
Upper limit(Stored)
Seenfrombelow


13

E110628E(I)


Whenthe UP positionis too low
                             
When thestored position is too low, follow the next steps and adjust.
Make sure the screen is stored before adjustment. Put the hexagonal spanner in the same place as previous
page. Turn the adjustment volume counter-clock-wise. Be careful not to adjust too much.
■Turndirection 

1 turn makesthe screen approx. 30mmup
Ref. 1/2 turn: approx. 15mm
※Remember the times of turn until the final confirmation of the
UP position.

         
②    ①

①After adjustment, push the DOWN button of the IR remote
controller. When the screen is drawn approx. 20-30cm, push
the STOP button.
②Push UP button and confirm whether the screen stops at the
desired position.
If the adjustment volume is turned CCW excessively, even after the screen is stored in the case, the
under pipe hits the case, and the motor does not stop. Push the STOP button to stop the
operation.
After stopping the operation, turnthe adjustment volume CW. (Seethe previous page)

Confirm if the screen stops at the desired positions by pushing DOWN,STOP and UP buttons. Do not forget
toput backthe cover to the limit adjustment hole.
Seen fromthe front
Seen from below
If the volume isadjusted CCW too much, the screen digs into the case, and
the fabric is pulled causing breakdown and wrinkles.
Stored
position⇒
UP
Desiredposition⇒

UP
Reminder:
Be careful in repeating the screen going up and down. The continuous use of the UP and DOWN
operations may cause the heat prevention circuitry work and stop the screen. When this happens,
pleaseoperate after some time (15-20 minutes) for cooling off.
-This is not the breakdown.
CAUTION


14

E110628E(I)

■Change of【DOWN】position    It shouldbeupper than thepre-set position.
Confirm the adjustment volume in the left sideofthe case.
Make sure the screen is set at DOWN (Projection) position before adjustment.










Put the hexagonal spanner to the limit adjustment volume, and turn it clock wise. Gradual adjustments
recommended not exceeding the screen up position.

■ Turndirection









1 turn makesthe screen approx. 30mmup
Ref. 1/2 turn: approx. 15mm
※Remember the times of turn until the final confirmation of
the DOWN position.




② ①



① After adjustment, push the UP button of the IR remote controller. When the screen is rolled up
approx. 20-30cm, push the STOP button.
② PushDOWN button and confirm whether the screenstops at the desired position.
Seen fromthe front
Seen from below
Preset

position

⇒
DOWN
Desiredposition

DOWN⇒

Inside the case
Limit adjustment volume
Lower limit (Projection)
Adjustment volume
Lower limit (Projection)
Seen from below


15

E110628E(I)

When the [DOWN] position is too high
                             
When theprojection position is too high, follow the next stepsand adjust.
Make sure the screen is in projection position before adjustment. Put the hexagonal spanner in the same
place as previous page. Turn the adjustment volume counter-clock-wise. Be careful not to adjust too
much.
■Turndirection
   




1 turn makesthe screen approx. 30mmdown.
Ref. 1/2 turn: approx. 15mm
※Remember the time of turn until the final confirmation of the
UP position.



② ①






① After adjustment, push the UP button of the IR remote controller. When the screen is rolled back
approx. 20-30cm, push the STOP button.
② Push DOWN button and confirm whether the screenstops at the desired position.
Seen fromthe front
Seen from below
If the volume is adjusted CCW too much, the fabric might fall or rolled
back reversely, causing wrinkles. Do not pull out the fabric more than
STOP label.
Projection
positionDOWN ⇒


Desired position

DOWN⇒
Reminder:
Be careful in repeating the screen going up and down. The continuous use of the up and down
operations may cause the heat prevention circuitry work, and stop the screen. When this happens,
pleaseoperate after some time (15-20 minutes) for cooling off.
This is not the breakdown.
CAUTION


16

E110628E(I)

Q&A
Please do the following checks beforerequesting forrepair when malfunction happens.
Please pull out the power plug before you check. Ifthe malfunction cannot be remedied even after all the checking
points as beloware confirmed, consult withthe dealer or us.
Symptom Check Remedy
The projected image becomes
inclined. Isthe screenmounted horizontally?
Check the mounting holes.
Is power plug fixed to the mains
correctly? Fixthe plug tightly.
Is the remote controller directed to
thereceiver? Direct the remote controller to the receiver.
Anything blocking between remote
andthereceiver? Take off the blocking item, or change the receiver position.
Is the sun or lights reflected on the
receiver? Changethepositionofthe receiver.
Batteriesofremote low? Change the two batteries in the
remote.(AAA type)
The screendoes not operate.
Is the heat preventioncircuitryon? Cool off the motor and operate
again after 15-20 minutes.
The screen is stored, but the
motor does not stop. Is the limit volume (Upper limit) turnedtoo much CCW?
Stop the operation. Readjust the
upper limit referring to page 12 of
Installation Manual.



17

E110628E(I)

Specifications
■Mountingbracket
■Side view(Stored)
E1-□□□H-□□□/E1-□□□V-□□□
Total
length A
From screw to screw G
Powercable(Approx.2.0m)


18

E110628E(I)

OSI CO., LTD.
Room 1605, 16/F, Seaview Centre, 139 Hoi Bun Road,
Kwun Tong, Kowloon, Hong Kong
PHONE:[phone]FAX:[phone]
E-mail:[e-mail]
URL:http://hk.os-worldwide.com
Model Size
W×H(mm) UBB U(mm) T. Length A(mm) From screwto screw
G(mm) T. Height
T(mm) Weight (kg)
Power
Consumption
(VA)
E1-080H-064 1771×996 640 2046 9.4
E1-090H-051 1992×1121 510 2267 1350 or above 10.3
E1-100H-039 2214×1245 390 2489 11.2
E1-110H-027 2435×1370 270 2710 1800 or above 12.1
E1-120H-014 2657×1494 140 2932 2250 orabove
1812
13.0
92
E1-080H-110 1771×996 1100 2046 10.0
E1-090H-097 1992×1121 970 2267 1350 or above 10.9
E1-100H-085 2214×1245 850 2489 11.8
E1-110H-073 2435×1370 730 2710 1800 or above 12.7
E1-120H-060 2657×1494 600 2932 2250 orabove
2272
13.6
92
E1-080V-088 1626×1219 880 1901 9.5
E1-090V-072 1829×1372 720 2104 1000 or above 10.3
E1-100V-057 2032×1524 570 2307 11.1
E1-110V-042 2235×1676 420 2510 1350 or above 12.0
E1-120V-027 2438×1829 270 2713 1700 orabove
2272
12.8
92
E1-100L-064 2337×995 640 2612 1800 orabove 10.0
E1-110L-054 2571×1094 540 2846 2250 or above 1812 12.5 92
     Specifications and design maychange without prior notice.