Outback Power Systems FX Series User manual

FX SERIES
INVERTER/CHARGER
FX/ VFX/GTFX/GVFX/MOBILE
Installation Manual

Warranty Introduction
Dear OutBack Customer,
Thank you for your purchase of OutBack products. We make every eort to assure our power
conversion products will give you long and reliable service for your renewable energy system.
As with any manufactured device, repairs might be needed due to damage, inappropriate use, or
unintentional defect. Please note the following guidelines regarding warranty service of OutBack
products:
• Any and all warranty repairs must conform to the terms of the warranty.
• All OutBack equipment must be installed according to their accompanying instructions and manuals
with specied over-current protection in order to maintain their warranties.
• The customer must return the component(s) to OutBack, securely packaged, properly addressed,
and shipping paid. We recommend insuring your package when shipping. Packages that are not
securely packaged can sustain additional damage not covered by the warranty or can void warranty
repairs.
• There is no allowance or reimbursement for an installer’s or user’s labor or travel time required to
disconnect, service, or reinstall the damaged component(s).
• OutBack will ship the repaired or replacement component(s) prepaid to addresses in the continental
United States, where applicable. Shipments outside the U.S. will be sent freight collect.
• In the event of a product malfunction, OutBack cannot bear any responsibility for consequential
losses, expenses, or damage to other components.
• Please read the full warranty at the end of this manual for more information.
About OutBack Power Systems
OutBack Power Systems is a leader in advanced energy conversion technology. Our products include
true sine wave inverter/chargers, maximum power point charge controllers, system communication
components, as well as breaker panels, breakers, accessories, and assembled systems.
Notice of Copyright
FX Series Inverter/Charger FX/VFX/GTFX/GVFX/MOBILE Installation Manual © 2008 All rights reserved.
Disclaimer
UNLESS SPECIFICALLY AGREED TO IN WRITING, OUTBACK POWER SYSTEMS:
(a) MAKES NO WARRANTY AS TO THE ACCURACY, SUFFICIENCY OR SUITABILITY OF ANY TECHNICAL OR
OTHER INFORMATION PROVIDED IN ITS MANUALS OR OTHER DOCUMENTATION.
(b) ASSUMES NO RESPONSIBILITY OR LIABILITY FOR LOSS OR DAMAGE, WHETHER DIRECT, INDIRECT,
CONSEQUENTIAL OR INCIDENTAL, WHICH MIGHT ARISE OUT OF THE USE OF SUCH INFORMATION. THE
USE OF ANY SUCH INFORMATION WILL BE ENTIRELY AT THE USER’S RISK.
Contact Information
OutBack Power Systems
19009 62nd Ave. NE
Arlington, WA 98223 Phone [phone] • Fax [phone] www.outbackpower.com
Date and Revision • June 2008 REV B

1
TABLE OF CONTENTS
Welcome to the OutBack Power Systems FX Series Inverter/Charger System...................................................................2
FX Series Inverter/Charger Models.................................................................................................................................................................2
Parts Included..............................................................................................................................................................................................................2
Safety Instructions.....................................................................................................................................................................................................3
System Protection.....................................................................................................................................................................................................5
DC Wiring Origination....................................................................................................................................... .....................................................5
AC Wiring Origination.............................................................................................................................................................................................6
AC Wiring Compartment Board................................................................................................................... ....................................................6
Low Voltage Terminals............................................................................................................................................................................................7
AC and DC Grounding Requirements............................................................................................. .............................................................8
FX Parts and Accessories.......................................................................................................................................................................................9
Mounting.....................................................................................................................................................................................................................10
Wire Connections...................................................................................................................................................................................................11
AC ......................................................................................................................................................................................................................11
DC ......................................................................................................................................................................................................................12
Battery Wiring Samples.......................................................................................................................................................................................13
AC Wiring Notes for the Non-Mobile FX..................................................................................................................................................20
AC Wiring Notes for the Mobile FX..............................................................................................................................................................21
Low Voltage Wiring................................................................................................................................................................................................22
Inverter and On/O................................................................................................................................................. ...................................22
Auxiliary Output (AUX+ / AUX-)..........................................................................................................................................................23
XCT+ / XCT-................................................................................................................................................................. ....................................23
RTS, MATE/HUB Wiring........................................................................................................................................................................................24
System Installation.................................................................................................................................................................................................25
Single FX System.................................................................................................................................................... ......................................25
Series or Series Parallel Dual FX Conguration..........................................................................................................................26
Paralleled Dual FX System.......................................................................................................................................................................28
Series/Parallel Quad FX System...........................................................................................................................................................29
3-Phase System............................................................................................................................................. ................................................31
Mobile Single FX .....................................................................................................................................................................................................33
Generator Interfaces.............................................................................................................................................................................................34
Mobile FX Information..................................................................................................................................... ...................................................35
Installation Check List..........................................................................................................................................................................................36
Appendix Ratings............................................................................................................................................................................................37-44
Voltage, Current, and Frequency Ranges .........................................................................................................................................45-47
Maximum Overcurrent Protection Ampacity .......................................................................................................................................48
FX Default Values....................................................................................................................................................................................................49
Wire Sizes.....................................................................................................................................................................................................................50
Maintenance..............................................................................................................................................................................................................51
Warranty................................................................................................................................................................................................................52-53
Product Registration.............................................................................................................................................................................................55
10 Year Limited Warranty (California) ..................................................................................................................................................55-56
10 Year Warranty Registration (California) ...............................................................................................................................................57

2
Welcome to the OutBack Power Systems FX Series Inverter/Charger System
The FX Series Inverter/Charger oers a complete power conversion system—DC to AC, battery charging, and an
AC transfer switch—and can be used as a stand-alone or back-up application. It is designed for indoor or enclosed
locations.
OutBack Power Systems does everything possible to assure the components you purchase will function properly
and safely when installed as instructed according to local and national electrical codes (NEC). Please read all of
the following instructions and the instructions that come with any other OutBack components that make up your
power system. Further instructions on individual FX set-ups as well as systems assemblies are included with the
FLEXware manuals.
• The non-Mobile FX is ETL listed to UL1741 (Inverters, Converters, Controllers, and Interconnection System
Equipment for Use with Distributed Energy Resources).
• All Mobile FX Series Inverter/Chargers are ETL listed to UL 458.
The FX and VFX Series Inverter/Charger Installation Manual covers the following information:
• Safety
• FX parts, standard and optional
• Initial inspection of the component
• Preparing the mounting surface
• Fastening the FX to the mounting surface
• General electrical information
FX Series Inverter/Charger Models
Sealed Units (designed for harsher environments, but still require enclosed protection)
FX2012 T (12 VDC/2000 VA) • FX2012 MT (12 VDC/2000 VA) • GTFX2524 (24 VDC/2500 VA)
FX2524 T (24 VDC/2500 VA) • FX2524 MT (24 VDC/2500 VA) • GTFX3048 (48 VDC/3000 VA)
FX3048 T (48 VDC/3000 VA) • FX2532 MT (32 VDC/2500 VA) (MT= Mobile GT= Grid-Tie)
Vented Units (designed for protected environments)
VFX2812 (12 VDC/2800 VA) • VFX2812 M (12 VDC/2800 VA) • GVFX3524 (24VDC/3500 VA)
VFX3524 (24 VDC/3500VA) • VFX3524 M (24 VDC./3500 VA) • GVFX3648 (48 VDC/3600 VA)
VFX3648 (48 VDC/3600VA) • VFX3232 M (32 VDC/3200 VA)
Each model FX has a single phase output marked with this symbol:
Each inverter puts out a sine wave waveform marked with this symbol:
Parts Included
One FX Series Inverter/Charger
One “WARNING ELECTRICAL SHOCK” sticker to place on the exterior of the FX
One packet of silicone grease to protect CAT 5 cable connections
One installation manual
One programming manual
One Turbo Kit (sealed units)
One DC Wiring Cover or DCC (vented units)
•
•
•
•
•
•
•
•
•
•
•
•
•

3
SAVE THESE INSTRUCTIONS
Read all instructions and cautionary markings on the FX, the batteries and all appropriate sections of
this installation and user manual as well as other component manuals before using the system.
Be cautious around electricity, electrical components, and batteries. Shocks, burns, injury, and even
death can occur if an installer comes in contact with electricity.
Install all components and wiring according to national and local electrical and building codes. This
includes:
• Submitting a plan to the local building department
• Passing inspection
• Requiring a licensed electrician to do the work when mandated
OutBack Power Systems cannot be responsible for system failure, damages, or injury resulting from
improper installation of their products.
Use only the recommended DC and AC wire sizes or greater. Be sure all wires are in good condition.
Install the FX in a dry location, preferably indoors.
• Install the FX in a shaded area out of direct sun
light for best operation.
• For installations where the FX may be exposed to water spray, a sealed FX must be used and
mounted either with the base down (shelf mounting) or with the AC wiring compartment facing
down (wall mounting).
• If mounted with the base down, water cannot be allowed to accumulate around the FX’s base. There
is a drainage system on the base of the FX to dispel condensation.
• If submerged, water can enter this drain and cause failure.
• The Vented FX (VFX) must be installed in a weather-proof enclosure or enclosed area. It is not
designed for exposure to water or excessive wind-blown dust and debris.
INITIAL INSPECTION
Your FX is stoutly packaged for secure shipping. Please inspect the packaging and component for
damage prior to installation.
READ FIRST!
IMPORTANT SAFETY INSTRUCTIONS

4
Design the battery enclosure to prevent accumulation and concentration of hydrogen gas in “pockets”
at the top of the enclosure. Vent the battery compartment from the highest point to the outside. A
sloped lid can also be used to direct the ow of hydrogen to the vent opening.
CAUTION
To reduce risk of injury, charge only deep-cycle lead acid, lead antimony, lead calcium, gel cell or
absorbed glass mat type rechargeable batteries. Other types of batteries may burst, causing personal
injury and damage. Never charge a frozen battery.
PERSONAL PRECAUTIONS
• Someone should be within range of your voice to come to your aid if needed.
• Keep plenty of fresh water and soap nearby in case battery acid contacts skin, clothing, or eyes.
• Wear complete eye protection. Avoid touching eyes while working near batteries. Wash your hands
with soap and warm water when done.
• If battery acid contacts skin or clothing, wash immediately with soap and water. If acid enters an
eye, ood the eye with cool running water at once for at least 15 minutes and get medical attention
immediately following.
• Baking soda neutralizes lead acid battery electrolyte. Keep a supply on hand in the area of the
batteries.
• NEVER smoke or allow a spark or ame in vicinity of a battery or generator.
• Be extra cautious to reduce the risk of dropping a metal tool onto batteries. It could short-circuit the
batteries or other electrical parts which can result in re or explosion.
• Remove personal metal items such as rings, bracelets, necklaces, and watches when working with
a battery or other electrical current. A battery can produce a short circuit current high enough to
weld a ring or the like to metal, causing severe burns.
PLEASE NOTE THE FOLLOWING SYMBOLS:
Pertains to a Grid-Tie FX Pertains to a Mobile FX
WARNING: WORKING NEAR LEAD ACID BATTERIES CAN BE DANGEROUS.
BATTERIES GENERATE EXPLOSIVE GASES DURING NORMAL OPERATION.
MGT

5
DC WIRING ORIGINATION
DC brass battery terminals with 8M x 1.00 stainless steel threaded studs
Red terminal=battery positive Battery terminal coversBlack terminal = battery negative
SYSTEM PROTECTION
Electrical systems are designed to protect you, the wires, the components, and the devices served by
the system.
Each FX must be part of a permanently grounded
electrical system (see page 8). Grounding protects
people and equipment from electrical shock.
Grounding must be done according to local and
national electrical codes.
OutBack circuit breakers—rated at 100% duty
cycle— protect wiring by limiting the amount
of current entering a system. All wired electrical
systems require circuit breakers or fuses for
protection.
OutBack oers both breakers and fuses for over-
current protection. If they are provided by other
vendors, they must be properly rated.

6
AC WIRING ORIGINATION
Lexan cover protects AC Wiring
Compartment Board
AC WIRING COMPARTMENT BOARD
AC HOT OUT supplies power to the loads.
AC NEUTRAL OUT acts as neutral leg for loads
supplied by the FX.
CHASSIS GROUND connections are common
and act as grounds for both the incoming and
outgoing AC circuits.
AC NEUTRAL IN acts as the neutral leg for AC
power supplied by either the grid or a generator
to the FX.
AC HOT IN connects incoming AC from the grid or
a generator to the FX. This AC is used to run loads
and recharge batteries.
NOTE: “CHASSIS GROUND” in the AC terminal
block reads as“NEU/GROUND BOND” ON FX
MOBILE SERIES (see page 21).
NOTE: 6 AWG (4.11 mm) is the largest wire
size the AC Wiring Compartment Board can
accommodate.
AC HOT OUT
AC NEUTRAL OUT
CHASSIS GROUND/PE
CHASSIS GROUND/PE
AC NEUTRAL IN
AC HOT IN
BATTERY
FULL OK LOW
STATUS
INVERTER
AC IN ERROR
BATTERY TEMP
MATE/HUB
INVERTER ON/OFF
INVERTER
ON/OFF
AUX+
AUX-
XCT-
XCT+
AC Terminal Block--secures AC
connections to the FX using set screws
AC Wiring Board
M

7
LOW VOLTAGE TERMINALS
Control Wiring
Terminal Block
NOTE: Keep Control
Wiring Terminal Block
screws tight and the
block itself secured tightly
to AC Board. Otherwise,
the FX can malfunction.
The Terminal Block can be
unplugged for easier wire
installation and removal/
reinstallation of the FX.
AUX OUTPUT
(AUX+/AUX-): 12VDC
at 0.7 amps (8.4 watts)
maximum is available at
these terminals; the AUX’s
default is to drive cooling
fans or the Turbo Fan.
XCT+/XCT- are non-
operational terminals (do
not connect).
INVERTER ON/OFF:
allows for manual
switch to control the
FX (default operation
is “ON”); controlled
by the MATE when
the installed jumper
connecting these
terminals is present.
Jumper
AC HOT OUT
AC NEUTRAL OUT
CHASSIS GROUND/PE
CHASSIS GROUND/PE
AC NEUTRAL IN
AC HOT IN
BATTERY
FULL OK LOW
STATUS
INVERTER
AC IN ERROR
BATTERY TEMP
MATE/HUB
INVERTER ON/OFF
INVERTER
ON/OFF
AUX+
AUX-
XCT-
XCT+

8
AC AND DC GROUNDING REQUIREMENTS
• Connect only to a grounded, permanent wiring system. Ensure there is only one neutral-ground
connection in the system at any time. Some codes require this connection be made at the main
panel only.
• Some generators have their own neutral ground connection. If a generator is used, its neutral-
ground connection will need to be disengaged for proper system operation.
• For all installations, the negative battery conductor should be bonded to the grounding system at
one (and only one) point in the system.
• OutBack products are not designed for use in a positive grounded system. Please contact OutBack
Technical Support for further information.
The equipment ground on each is marked with this symbol:
Box lug for grounding the FX chassis

9
FX PARTS AND ACCESSORIES
*NOTE: A GTFX requires an OutBack FLEXware
Surge Protector per the UL 1741 listing.
GT
BATTERY TERMINAL COVERS
• The caps are made of sti plastic with a snap-on
design; remove them carefully using a at-blade
screwdriver inserted into the slots on the sides of
each cover.
• DC conduit may be required for exposed
installations.
• The DCA cover option (see below) allows conduit
connection.
• Always keep the battery terminal covers installed.
AC CONDUIT PLATE*
• AC conduit connects to the AC Con-
duit Plate for installations which do
not utilize an optional FW-ACA.
DCA (DC CONDUIT ADAPTER)
• Allows the connection of two-inch TSC (Trade Size
Conduit) to the FX
• Connects to OutBack’s FLEXware enclosures
DCC (DC COMPARTMENT COVER)
• Covers the DC terminal area and provides space
to mount other components such as a DC current
shunt
• Can be used with or without the DCA
• This is an optional accessory.
FW-ACA (AC CONDUIT ADAPTER)
• Extends the AC wiring compartment
• Connects to OutBack’s FLEXware enclosures
• Protects and secures exible cable with strain relief
• Houses the FLEXware Surge Protector
• Knockouts are intended for cables/strain relief
• This is an optional accessory.
TURBO FAN COVER
• Included in place of a DCC on sealed FXs

10
MOUNTING
• The FX Series Inverter/Charger is approved for indoor or enclosed protected mounting only.
• An FX must be secured with appropriate fasteners to a sturdy mounting surface capable of
supporting its weight. It is easier for two people to install the FX due to its weight.
• OutBack FXs can be mounted in any position, but they perform better in locations oering plenty of
air circulation.
• NOTE: If using an OutBack FLEXware Mounting Plate, avoid large air gaps behind the plate which can
result in louder mechanical noise during inverting/charging under heavy loads.
• Due to the variance in other mounting methods, OutBack only endorses the use of FLEXware or
previous versions of its mounting plate for installing the FX and associated system components
using M6 X 20mm machine screws (stainless steel for FLEXware and self-tapping for older mounting
plates), one per corner. Follow the instruction manual that comes with each mounting system.
• If mounting the FX on other surfaces such as plywood, wall studs, or masonry, use appropriate
fasteners to support approximately its weight. OutBack cannot be responsible for damage to the FX
if it is attached with inadequate fasteners.
• Install and secure each FX before attaching any wiring.
• Insert appropriate fasteners at all four corners of the FX for a secure installation.
• Weight varies from 56-62.6 pounds (25.40 - 28.395 kg) depending on the model
20.955 cm (8.25””)
32.03 cm (13”)
41.275 cm (16.25”)

11
AC
Follow these steps to wire the FX to your system:
1. Shut all AC breakers o or remove any fuses before connecting any wiring.
2. Shut o all DC breakers, including the PV breakers.
3. With all power o, run lengths of 6 AWG (13.3 mm2)wire between the AC Wiring Compartment
Board AC out terminals and sucient over current protection via an AC circuit breaker whose
ampacity matches or exceeds the maximum AC input current of the FX model used in the system
(see FX product specications). The breaker should be installed inside of a metal chassis such as
OutBack’s FLEXware series or an existing panel.
4. With the over current protection connected, run lengths of 6 AWG (13.3 mm2) wire between the
AC Wiring Compartment Board AC IN terminals and the AC input breaker. The breaker should be
installed inside of a metal chassis such as OutBack’s FLEXware series or an existing panel. The AC
input hot conductor must be supplied through an AC branch-rated circuit breaker whose ampacity
matches or exceeds the maximum AC input current of the FX model used in the system (see FX
product specications)
While 60 amp over-current protection reduces the risk of re, for further reduction,
do not connect a single FX to both hot legs of a 120-240 VAC AC load center having
multi-wire (common neutral) branch circuits connected. Use either two FX Series
Inverter/Chargers wired in a series conguration or an FW-X240 Auto Transformer.
NOTE: Connect Mobile FX equipment to an AC circuit with 30 amp maximum branch-circuit
over-current protection (as per NEC, ANSI/NFPA 70).
M
WIRE CONNECTIONS
NOTE: A system’s individual voltage requirements (120 single phase, 120/240 split phase, or 3-phase) as
well as how each FX is to function all determine how the FXs are wired. Each FX must be wired to the
logical leg or phase of the system. Each FX must be programmed or “stacked”according to this phase.
Please see the FX and VFX Series Inverter/Charger Programming Manual before connecting any wires to
or from the FX.

12
DC
• Use crimped and sealed copper ring terminal lugs with 5/16” (.79 cm) hole or compression-type lug
to connect battery cables to DC terminals. Soldered cable lugs are also acceptable.
• Use recommended cable sizes (see page 51) to reduce losses and ensure high performance of FX
(smaller cables can reduce performance and possibly damage the unit).
• Keep cables together (e.g., using a tie-wrap) as much as possible.
• Ensure cables pass through the same knockout and conduit ttings to allow inductive currents to
cancel.
TORQUE REQUIREMENTS
CONNECTION TORQUE IN POUNDS/Nm
AC and PV breakers to 22 inch-lbs/2.48 Nm
DC shunt to 15 foot-lbs/20.4 Nm
DC battery connections to 10 foot-lbs/13.6 Nm
FX’s DC terminals to 5 foot-lbs/3.38 Nm
FX’s AC terminals to 30 inch-lbs/3.38 Nm
Table 1 Torque Values for Installation

13
Battery Wiring Examples
• Never install extra washers between the
terminal mounting surface and the battery
cable lug—the connection must be direct and
secure.
• Always install breakers or fuses within the
positive battery cable.
• Torque 2/0, (67.4 mm2) 4/0 (107 mm2), or larger
code-approved cables rated 75°C or higher to
60-inch pounds/6.77Nm.
In renewable energy systems, batteries are connected to each other in one of three ways:
• Series (voltage increases, amperage stays the same as a single battery)
• Parallel (voltage stays the same as a single battery, amperage increases)
• Series/Parallel (both voltage and amperage increase)
Voltage remains at 12V 200AH + 200AH + 200AH + 200 AH=800 AH
+ -
12V/200 Amp Hours
+ -
12V/200 Amp Hours
+ -
12V/200 Amp Hours
+ -
12V/200 Amp Hours
+ -
12V/200 Amp Hours
+ -
12V/200 Amp Hours
+ -
12V/200 Amp Hours
+ -
12V/200 Amp Hours
12V + 12V + 12V + 12V = 48 V Amp Hours remain at 200
+ -
12V/200 Amp Hours
+ -
12V/200 Amp Hours
+ -
12V/200 Amp Hours
+ -
12V/200 Amp Hours
+ -
12V/200 Amp Hours
+ -
12V/200 Amp Hours
+ -
12V/200 Amp Hours
+ -
12V/200 Amp Hours
Two strings of batteries in series are connected in parallel. The voltage increases to 48V and the
amp hours increase to 400
SERIES
PARALLELSERIES/PARALLEL
Battery Cable Lug
Lock Washer
Flat Washer
Nut
Insulator
Stud

14
-
-
12 VOLT INVERTER/CHARGER
6V Battery Wiring Examples
DC DISCONNECT (FUSE OR CIRCUIT
BREAKER)
6 VOLT 6 VOLT
-
SERIES/12 VOLT FX
12 VOLT INVERTER/CHARGER
SERIES/PARALLEL/12 VOLT FX
-
-
6 VOLT 6 VOLT
-
-
6 VOLT 6 VOLT
SERIES STRING 1 CONNECTS TO
INVERTER/CHARGER’S POSITIVE
TERMINAL
DC DISCONNECT (FUSE OR CIRCUIT
BREAKER)
SERIES STRING 2
SERIES STRING 1
-

15
24 VOLT INVERTER/CHARGER
-
DC DISCONNECT (FUSE OR CIRCUIT
BREAKER)
-
6 VOLT
-
6 VOLT
-
6 VOLT 6 VOLT
-
SERIES/24 VOLT FX
24 VOLT INVERTER/CHARGER
-
-
DC DISCONNECT (FUSE OR CIRCUIT
BREAKER)
-
6 VOLT
-
6 VOLT
-
6 VOLT 6 VOLT
-
-
6 VOLT
-
6 VOLT
-
6 VOLT 6 VOLT
SERIES STRING 1
SERIES STRING 2
SERIES STRING 2 CONNECTS
TO INVERTER/CHARGER’S
NEGATIVE TERMINAL
SERIES STRING 1 CONNECTS TO
INVERTER/CHARGER’S POSITIVE
TERMINAL
SERIES/PARALLEL/24 VOLT FX

16
48 VOLT INVERTER/CHARGER
-
-
DC DISCONNECT
(FUSE OR CIRCUIT BREAKER)
-
6 VOLT
-
6 VOLT
-
6VOLT 6 VOLT
-
-
6 VOLT
-
6 VOLT
-
6 VOLT 6 VOLT
SERIES/48 VOLT FX

17
-
DC DISCONNECT (FUSE OR
CIRCUIT BREAKER)
-
12 VOLT 12 VOLT
-
24 VOLT INVERTER/CHARGER SERIES/24 VOLT FX
12V Battery Wiring Examples
-
DC DISCONNECT (FUSE OR
CIRCUIT BREAKER)
-
12 VOLT
-
12 VOLT
-
12 VOLT 12 VOLT
-
12 VOLT INVERTER/CHARGER
PARALLEL/12VOLT FX

18
48 VOLT INVERTER/CHARGER
-
DC DISCONNECT (FUSE OR CIRCUIT
BREAKER)
-
12 VOLT
-
12 VOLT
-
12VOLT 12 VOLT
-
SERIES/48 VOLT FX
-
-
12 VOLT 12 VOLT
-
-
12 VOLT 12 VOLT
SERIES STRING 1 CONNECTS TO
INVERTER/CHARGER’S POSITIVE
TERMINAL
24 VOLT INVERTER/CHARGER
DC DISCONNECT (FUSE OR
CIRCUIT BREAKER)
SERIES STRING 2
SERIES/PARALLEL/24 VOLT FX
SERIES STRING 1
-