Outdoor GreatRoom Company Alcott ALC-1224 User manual

Alcott Fire Table
Installation Instructions for ALC-1224

2
Contents
Required Tools………………………………….........2
Included With Your Fire Pit……………………….3
Un-Packaging…………..……………………………….4
Base Placement………………………………………..4
CF-SPARKER Installation…………………………….5
Supercast Top Placement………………………….5
Gas Connections……………………………………….6
Electrode Installation………………………………..8
Propane Tank Installation………………………….9
Fire Media Installation……………………………….9
Operating Instructions………………………………10
Required Tools
TWO people are required for this installation.
2 Open Ended Wrenches
To secure gas connections.
Leather Gloves
To protect hands from rough edges found on fire pit
during installation.
One AAA Battery (not included)
Required for electric spark igniter installation.
Utility Knife
To cut and remove packaging.
IMPORTANT
Please consult your Crystal Fire instruction manual for detailed
instructions and important information related to the burner
installation including: lighting and operating instructions, safety
information, and proper tightening of connections with two wrenches.
DO NOT ATTEMPT TO INSTALL CRYSTAL FIRE BURNER WITHOUT
FIRST CONSULTING THE CRYSTAL FIRE OWNER’S MANUAL.
42482 REV-A 9-20-17

3
Included With Your Fire Pit
Alcott 1224 base
(Control Panel Installed)
ALC-1224-BASE
Antique Timber Supercast
Top and Burner Cover
3648-1224-AT & 3648-1224-
AT-C
1224 Crystal Fire Burner
with Brown Trim
CF-1224-BRN
Refer to Crystal Fire Manual for items included with crystal fire burners.

4
Assembly Instructions
1. Un-packaging
Do not discard any packaging until assembly is
complete and unit is tested.
Keep all included manuals in a safe place for
future reference.
2. Base Placement
Place base in desired final location.
Place on a hard, flat surface. Avoid soft
surfaces and areas that collect water.
Refer to Crystal Fire Manual included with
your Crystal Fire Burner for safety information
regarding the placement of your fire pit.

5
3. CF-SPARKER Installation
Locate CF-SPARKER inside of crystal fire
burner box.
Remove CF-SPARKER cap and hex nut. Insert
AAA battery (not included) with + end out.
Install CF-SPARKER into control panel as
shown below.
Depress CF-SPARKER button to test your
sparker.
4. Supercast Top Placement
Caution: Top is heavy, two people are
required to lift and set in to place. Remove
burner cover before lifting the top to avoid
damage to the cover.
Construction adhesive can be used to
permanently secure top to base, if desired.

6
5. Gas Connections
Ensure valve is in the OFF position before
making any gas connections.
For propane tank installations, install included
propane hose and regulator to the control
panel as shown below. Use two wrenches to
ensure a gas tight connection.
For hard piped installations, connect the gas
supply line (not included) to the 3/8” male
flare fitting on the valve. Use two wrenches
to ensure a gas tight connection.
TIGHTEN CONNECTION
SECURELY WITH WRENCH
Propane regulator
Or gas supply line

7
Ensure the correct orifice is installed for the
fuel type you are using (see Crystal Fire
Burner Owner’s Manual included with burner
for orifice sizing information).
Ensure flex line is securely tightened to the
orifice. Use two wrenches as shown. One
wrench on the flex line and one on the orifice
for counter torque.
TIGHTEN ALL CONNECTIONS SECURELY WITH TWO WRENCHES
Attach flex line from the burner to gas valve
as shown. Use two wrenches to secure
connection.
TIGHTEN CONNECTION
SECURELY WITH TWO
WRENCHES
Flex line from burner
Flex line hex
Orifice Hex

8
Carefully place burner into burner opening,
oriented as shown.
6. Electrode Installation
Plug both BLACK wires hanging from the
burner into the back of the CF-SPARKER. If
an orange wire is present, do not use it. The
orange wire is for Direct Spark Ignition
system only.
Test system by pushing the button on the
igniter. Consult the troubleshooting section
of the Crystal Fire Burner Owner’s Manual,
if the spark is weak, intermittent, or not
present.
Electrode
Access door

9
7. Propane Tank Installation
With the propane tank valve and fire pit valve
off, attach the propane regulator to the
propane tank. Hand tighten, do not use a
wrench for this connection.
Insert propane tank into base by sliding it past
the red dotted line shown above.
Ensure no hoses or wires are contacting the
bottom of the burner.
Replace the access door.
8. Fire Media Installation
Scatter all included glass beads,
lava rock, or other approved fire
media evenly across entire burner
surface.
DO NOT OPERATE CRYSTAL FIRE BURNER WITHOUT INCLUDED GLASS
BEADS OR OTHER APPROVED FIRE MEDIA
DO NOT OPERATE CRYSTAL FIRE BURNER WITH BURNER COVER IN PLACE

10
9. Operating Instructions
Before operating your Alcott 1224 fire pit, ensure all gas
connections are properly tightened and thoroughly leak checked.
Refer to the Crystal Fire Manual for information on proper leak
checking and other critical safety information.
With the valve on the fire pit in the OFF
position, open the valve on the propane tank
or natural gas supply.
Double check to make sure there are no gas
leaks at the regulator or inlet side of the
valve. If leak is detected, immediately shut off
the gas supply and wait 5 minutes to allow
gas to dissipate. Fix any leaks before
proceeding.
Press the sparker button and hold, look and
listen for spark between electrode and
grounding rod.
While depressing the sparker, open the valve.
If burner does not light after 10 seconds,
close the valve and wait 5 minutes to allow
gas to dissipate before attempting ignition
again.
Refer to the Crystal Fire Manual included with your burner for
more detailed information on operation, maintenance, and safety
of your burner.
3. Turn valve to ON
2. Look/listen for spark
1. Depress sparker

11
WARNING
After consulting the manual and following instructions, remember; before
operating, all gas connections must be fully checked for leaks
IMPORTANT
Please consult your Crystal Fire instruction manual for detailed
instructions and important information related to the burner
installation including: lighting and operating instructions, safety
information, and proper tightening of connections with two wrenches.
DO NOT ATTEMPT TO INSTALL CRYSTAL FIRE BURNER WITHOUT
FIRST CONSULTING THE CRYSTAL FIRE OWNER’S MANUAL.

12
Thank you for purchasing an
Outdoor GreatRoom Company
product! This fire pit was made with
pride in the USA.
Warranty: Fire pit tables are covered under a 1-
year manufacturer’s warranty. Please visit
http://www.outdoorrooms.com/warranty-form
to register your product.
14400 Southcross Drive West •Suite 100 •Burnsville, MN 55306
Toll Free: 1-866-303-4028 •[e-mail]