Outdoor GreatRoom Company Crystal Fire CF-20 User manual

Page | 1 www.outdoorrooms.com Crystal Fire 42435 REV K 12.30.14
User Manual for: CF-20, CF-1224, CF-2424, CF-1242, CF-1242-L, CF-1264, CF-12120, NF-16, NF-
1919, NF-737, NF-719, custom burner sizes
CAUTION
DO NOT DISCARD THIS MANUAL
Important operating and
maintenance instructions
included.
Read, understand, and
follow these instructions
for safe installation and
operation.
WARNING
Crystal Fire
GAS-FIRED
WARNING
If the information in these instructions
is not followed exactly, a fire or
explosion may result causing property
damage, personal injury, or loss of life.
Do not store gasoline or other flammable vapors or
liquids in the vicinity of this or any other appliance.
What to do if you smell gas:
Do not try to light any appliance
Do not touch any electrical switch. Do not
use any phone in your building.
Immediately call your gas supplier from a
neighbor’s phone. Follow the gas supplier’s
Instructions.

If you cannot reach your gas supplier, call the
fire department.
Installation and service must be performed by a
qualified installer, service agency, or the gas
supplier.
HOT! DO NOT TOUCH.
SEVERE BURNS MAY RESULT.
CLOTHING IGNITION MAY RESULT.
Glass and other surfaces are hot
during operation and cool-down.
Keep children away.
CAREFULLY SUPERVISE children near this
appliance.
Alert children and adults to hazards of high
temperatures.
Keep clothing, furniture, draperies, and
other combustibles away.
WARNING
For outdoor use only
WARNING
It is imperative the burner be kept clean
WARNING
Improper installation, adjustment, alteration, service, or
maintenance can cause injury or property damage. Read
the installation and maintenance instructions
thoroughly before installing or servicing this equipment.
Installation and service of this appliance
should be performed by qualified
personnel. The Outdoor GreatRoom
Company suggests NFI certified, factory-
professionals, or technicians supervised
by an NFI certified professional.

Page | 2 www.outdoorrooms.com Crystal Fire 42435 REV K 12.30.14
Read this manual before installing or operating this appliance.
Please retain this owner’s manual for future reference.
Congratulations
Congratulations on selecting an Outdoor GreatRoom Company decorative gas appliance. The Crystal Fire you
have selected is designed to provide the utmost in safety, reliability, and efficiency.
As the owner of a Crystal Fire, you’ll want to read and carefully follow all of the instructions contained in this
owner’s manual. Pay special attention to all cautions and warnings.
This owner’s manual should be retained for future reference. We suggest you keep it with other important
documents and product manuals.
This information contained in this owner’s manual, unless noted otherwise, applies to all models and gas
control systems.
Your new Crystal Fire will give you years of durable use and trouble-free enjoyment.
Homeowner Reference Information
Model name:______________________________ Date of purchase/installation_________
Serial Number:___________________________ Location on appliance:_________________
Dealer purchased from:____________________ Dealer Phone:________________________
Notes:______________________________________________________________________
___________________________________________________________________________
___________________________________________________________________________
We recommend that you record the following
pertinent information about your appliance
Listing Label Information/Location
The model information regarding your specific appliance can be found on the rating plate attached to your
burner via a metal chain. See the sample rating plate below for locations of specifications.
Model
Fuel Type
Orifice Size
Serial no.

Page | 3 www.outdoorrooms.com Crystal Fire 42435 REV K 12.30.14
‘
Table of Contents
1. ListingandCodeApprovals
a. Appliance certification
b. BTUspecifications
2. Getting Started
a. Designandinstallationconsiderations
b. Toolsandsuppliesrequired
c. Inspection ofappliance andcomponents
d. Step-by-steplightinginstructions
3. Framing Clearances
a. Selectingalocation
b. Required clearancetocombustibles
c. Framing anenclosureforLPsupplysystem
4. FuelInformation
a. Fuel
b. Gaspressure
c. Gasconnection
d. LPGassupply
5. Appliance Setup
a. Burner assembly
b. Glassinstallation
6. OperatingInstructions
a. Before lighting
b. Lightingthefire
c. Afterthefireislit
7. Finishing
8. Convertingto NaturalGas
9. Troubleshooting
10.Maintainingandservicing theappliance
11.ReferenceMaterials
a. Servicepartslist
b. Limitedone-yearwarranty
c. Contactinformation

Page | 4 www.outdoorrooms.com Crystal Fire 42435 REV K 12.30.14
CF20 / NF-16
Round burner assembly
Black propane hose with
regulator
Flexible metal gas line
Piezoelectric igniter
#43 Orifice (LP)
#31 Orifice (NG)
2 bags of decorative glass
CF-1224 / NF-719
Rectangular Burner Assembly
Black propane hose with
regulator
Flexible metal gas line
Piezoelectric igniter
#43 Orifice (LP)
#31 Orifice (NG)
2 bags of decorative glass
CF-2424 / NF-1919
Square burner Assembly
Black propane hose with
regulator
Flexible metal gas line
Piezoelectric igniter
#36 Orifice (LP)
#17 Orifice (NG)
4 bags of decorative fire glass
What’s included…
CF-1264
Rectangular Burner Assembly
Black propane hose with
regulator
Flexible metal gas line
Piezoelectric igniter
#31 Orifice (LP)
#21 Orifice (NG)
4 bags of decorative fire glass
CF-1242 / NF-737
Rectangular Burner
Assembly
Black propane hose with
regulator
Flexible metal gas line
Piezoelectric igniter
#31 Orifice(LP)
#21 Orifice (NG)
3 bags of decorative fire
glass
CF-12120
Two-piece rectangular burner
assembly
Black propane hose with
regulator
Manifold kit (T-connector and
2 flexible metal hoses)
Piezoelectric igniter
#31 Orifice (x2)(LP)
#21 Orifice (x2) (NG)
8 bags of decorative fire glass
CF-1242-L
Two-piece burner assembly
Black propane hose with
regulator
Manifold kit (T-connector and
flexible metal hose)
2 Flexible metal gas lines
Piezoelectric igniter
#31 Orifice (x2)(LP)
#21 Orifice (x2) (NG)
6 bags of decorative fire glass

Page | 5 www.outdoorrooms.com Crystal Fire 42435 REV K 12.30.14
Model
Orifice Size
Max input BTU
LP
NG
LP
NG
·CF-20
·NF-16
#43
#31
55331
51706
·CF-1224
·NF-719
#43
#31
55331
51706
·CF-2424
·NF-1919
#36
#17
79229
107465
·CF-1242
·NF-737
#31
#21
100588
90776
·CF-1264
#31
#21
100588
90776
·CF-12120
-CF-1242-L
#31(2)
#21(2)
100588 (per half)
90776 (per half)
MODEL: CRYSTAL FIRE CF-20, CF-1224, CF-2424, CF-1242-L,
NF-1919, NF-719, NF-737, NF-16, CF-1264, CF-12120
LABORATORY: Underwriters Laboratories, Inc. (UL)
TYPE: Decorative Gas-Fired Outdoor Fireplace
STANDARD: Out Decorative Gas Appliances ANSI
Z21.97-2014 * CSA 2.41-2014
The Crystal Fire has been tested in accordance with
ANSI Z21.97-2014 and CSA 2.41-2014 for Canada
andhasbeenlistedbyUnderwriters Laboratory (UL) for
installation and operation as described in these
installation and operating instructions.
The installation must conform with local codes or, in
the absence of local codes, ANSI Z223.1 * NFPA 54
National fuel gas code –Natural gas and propane
installation code, CSA B149.1 –or propane storage
and handling code, CSA B149.2
1 Listing and Code Approvals
A. Appliance Certification B. BTU Specifications

Page | 6 www.outdoorrooms.com Crystal Fire 42435 REV K 12.30.14
2 Getting Started
This appliance is a Decorative Gas Appliance for
OUTDOOR USE ONLY and MUST NOT be used
for cooking.
Place the Crystal Fire on a flat and stable surface in
an outdoor location such as a patio or deck. This
location must be adjacent to the gas supply line or
LP gas supply cylinder. DO NOT locate the
appliance where it will get excessively wet or
submerged in water.
A. Design and Installation Considerations
When planning an appliance installation, it’s necessary to
determine the following information before installing:
Where will the appliance be installed? See section 3
Gas supply piping. See section 4
Framing and finishing details. See sections 3,7
B. Tools and Supplies Required
Before beginning the installation, be sure that the
following tools and supplies are at hand.
Gloves
Safety Glasses
Phillips screwdriver
Non-corrosive leak-check solution
Wrenches
1 AAA battery
WARNING
The Outdoor GreatRoom Company
disclaims any responsibility for, and
the warranty will be voided by, the
following actions:
Installation and use of any damaged
components.
Modification of the burner assembly
Installation other than as instructed
by the Outdoor GreatRoom
Company.
Any such action may cause a fire hazard
WARNING
Do NOT use this appliance if any part of it has
been underwater. Have a qualified service
technician inspect the appliance and replace
any part of the control system and any gas
control which has been underwater.
CAUTION
Sharp Edges
Wear protective gloves and safety glasses
during installation.
WARNING
Do not burn solid fuels in this gas appliance
C. Inspect theApplianceandComponents
WARNING
Inspect appliance and components for
damage. Damaged parts may impair safe
operation.
Do NOT install damaged, incomplete,
or substitute components
Report damaged parts to your dealer.
WARNING
Asphyxiation Risk
This gas appliance is for outdoor use in a
well-ventilated space.
This unit must not be installed inside an
enclosed structure or unvented appliance
Carefully remove all burner
components from packaging.
Read all instructions before beginning
installation. Follow these instructions
carefully during installation to ensure
maximum safety and benefit.

Page | 7 www.outdoorrooms.com Crystal Fire 42435 REV K 12.30.14
3 Framing and Clearances
Note:
Illustrations reflect typical installations
and are FOR DESIGN PURPOSES ONLY.
Illustrations/diagrams are not drawn to
scale.
Actual installation may vary due to
individual design preference.
Fire Risk
Provide adequate clearance:
Around air openings
For service access.
Locate appliance away from traffic areas
WARNING
72 inches to overhang
from top of metal bowl.
Figure 3.1 Clearances to Combustibles
24” 24”
SIDE WALL
METAL
BOWL
If you are not using an
Outdoor GreatRoom
Company table with
this burner, be sure to
mount to a non-
combustible surface
maintaining at least
8to combustible
surfaces and framing
below the surface of
burner.
8”
8”
8”
8”
8”
72”

Page | 8 www.outdoorrooms.com Crystal Fire 42435 REV K 12.30.14
C. Framing Enclosure for LP Gas Supply
System
If you build an enclosure for an LP gas cylinder, follow
these recommended specifications and local codes:
Ventilation
Enclosures must be ventilated by openings at the level
of the cylinder valve and at floor level. Effectiveness must
be determined with the cylinder(s) in place.
One side of the enclosure must be completely
open or,
For an enclosure having four sides, a top and a
bottom:
- At least two ventilation openings at cylinder valve
level shall be provided in the side wall, equally sized,
spaced at 180 degrees (3.14 rad), and unobstructed.
Each opening must have a total free area of not less
than 1/2 square inch per pound (3.2 sq. cm/kg)of
stored fuel capacity and not less than a total free
area of 10 square inches (64.5 sq. cm).
- Ventilation opening(s) must be provided at floor
level and shall have a total free area of not less than
1/2 square inch per pound (3.2 sq. cm/kg) of stored
fuel capacity and not less than a total free area of
10 square inches (64.5 sq. cm). If ventilation
openings at floor level are in a side wall, there must
be a least two openings. The bottom of the openings
must be at floor level and the upper edge can’t be
more than 5 in. (127 mm) above the floor. The
openings must be equally sized, spaced at 180
degrees (3.14 rad) and unobstructed.
- Every opening must have minimum dimensions to
permit the entrance of a 1/8 inch (3.2 mm)
diameter rod.
Accessibility
Cylinder valves must be readily accessible for
hand operation. A door on the enclosure to
gain access to the cylinder valves is
acceptable, provided it is non-locking and
can be opened without the use of tools.
The design of the enclosure must be
such that:
- The LP gas supply cylinder(s) can be
connected, disconnected and the
connections inspected and tested
outside the cylinder enclosure.
- Those connections which could be
disturbed when installing the cylinder(s)
in the enclosure can be leak tested
inside the enclosure.
- Be certain to mount or set the LP gas
cylinder on a flat stable surface and
retain it to prevent it from tipping.
Minimum Clearances
There must be a minimum clearance of 2 in.
(50.8 mm) between the lower surface of the floor
of the LP gas supply cylinder enclosure and the
ground.

Page | 9 www.outdoorrooms.com Crystal Fire 42435 REV K 12.30.14
4 Setting up your Burner
A. Burner Assembly
All Models
Check for damage. Do not use damaged components.
The hose assembly must be replaced prior to the ap-
pliance being put into operation if there is evidence of
excessive abrasion or wear, or if the hose is damaged.
The replacement hose assembly specified by the man-
ufacturer.
The burner must be replaced prior to the appliance be-
ing put into operation if it is evident that the burner is
damaged. The replacement burner assembly specified
by the manufacturer.
Position the assembly in the desired location. This loca-
tion must be adjacent to the gas supply line. You must
have easy access to the gas valve control knob after it
is installed and connected to the gas supply because
the ON/OFF gas valve is used to turn the burner on and
off.
LP Gas Models
Make sure the tank valve is turned completely off
(clockwise).
Ensure the tank valve has the proper external
mating
threads (tank valve marked “USE WITH TYPE
1”).
Inspect the hose shipped with the appliance
for any
damage. Do not use if there is evidence of
damage.
Connect the end of the hose onto the
ON/OFF gas
valve of the appliance. Make sure it is secured
tightly.
Connect the regulator assembly to the tank valve.
Hand-tighten only (clockwise). Do not use a
wrench to tighten! Use of a wrench may damage
the quick closing nut and result in a hazardous
condition.
Position the hose out of pathways where people
might trip over it or in areas where the hose
might be subject to accidental damage.
B. Glass Installation
Spread glass out evenly over burner area. Use all glass
provided for best affect. Keep glass clear of spark to
avoid accidental blockage.
Note:
A percentage of glass beads may arrive split in half.
This is normal. Additional beads may split after use.
This is also normal due to the physical properties of
glass.
DO NOT BURN WITHOUT GLASS OR
OTHER SUBSRATE SUCH AS LAVA
ROCK IN BURNER.

Page | 10 www.outdoorrooms.com Crystal Fire 42435 REV K 12.30.14
C. Igniter Installation and Grounding
Note: Before installing ignition system, ensure that gas valves are closed and gas
is disconnected for safety.
Sparker
Spark wire
Ground wire
1. A grounding wire is included with your burner as shown above. This can be plugged into either port
on the back side of the sparker.
2. A spark wire hangs from the electrode at the end of the burner (also above). This can be plugged
into the remaining open port on the back side of the sparker to complete igniter hookup.
Note: It doesn’t make a difference which port the wires are plugged into, as long as they are both
plugged in.
A battery (AAA type) should be installed in the igniter before use. The battery’s positive end (+)
should face outward when installed.
(Or other thin surface)

Page | 11 www.outdoorrooms.com Crystal Fire 42435 REV K 12.30.14
5 Gas Hookup and Information
A. Fuel
Before making gas connections, ensure the appliance being
installed is compatible with the available gas type.
B. Gas Pressure
Proper input pressures are required for optimum
performance. Gas line sizing requirements need to be made
following NFPA54
Pressure requirements for appliance are shown in
table below. Minimum pressures must be met when
other household gas appliances are operating.
Pressure
Natural Gas
Propane
Minimum Inlet Pressure
Maximum Inlet Pressure
7 in w.c. 11 in. w.c.
10.5 in w.c. 14 in. w.c.
WARNING
Fire Risk
Explosion Risk
Verify inlet pressures.
High pressure may cause
overfire condition.
Low pressure may cause
explosion.
Verify minimum pressures
when other household gas
appliances are operating
Install regulator upstream of valve if line
pressure is greater than ½ psig.
The appliance and its individual shutoff valve must be dis-
connected from the gas supply piping system during any
pressures in excess of 1/2 psi (3.5 kPa).
The appliance must be isolated from the gas supply piping
system by closing its individual manual shutoff valve during any
pressure testing of the gas supply piping system at test pressures
equal to or less than 1/2 psi (3.5 kPa).
C. Gas Connection
Note: Have the gas supply installed in accordance with
local building codes, if any. If not, follow ANSI 223.1.
Installation should be done by a qualified installer
approved and/or licensed as required by the locality.(In
the Commonwealth of Massachusetts installation must
be performed by a licensed plumber or gas fitter.
Note: A listed (and Commonwealth of
Massachusetts approved) 3/8 in. T-handle manual
shut-off valve and flexible gas connector are
connected to the 3/8 in. control valve inlet.
If substituting for these components, please consult local
codes for compliance.
Incoming gas line should be piped to the ½ inch
connection on the manual shutoff valve.
WARNING
Fire Risk
Explosion Risk
Gas build-up during line purge may
ignite.
Purge should be performed by
qualified technician.
Ensure adequate ventilation.
Ensure there are no ignition sources
such as sparks or open flames.
A small amount of air will be in the gas
supply lines. When first lighting appliance
it will take a short time for air to purge
from lines. Subsequent lighting of the unit
will not require such purging. Never allow
the ON/OFF valve to remain in the open
position without pressing and
continuing to hold igniter button FIRST.
WARNING
CHECK FOR GAS LEAKS
Fire Risk
Explosion Risk
Asphyxiation Risk
Check all fittings and connections.
Do not use open flame.
After the gas line installation is
complete, all connections must be
tightened and checked for leaks with
a commercially available leak-sheck
solution. Be sure to rinse off all leak
check solution. Be sure to rinse off all
leak check solution following testing.
Fittings and connections may have loosened during
shipping and handling

Page | 12 www.outdoorrooms.com Crystal Fire 42435 REV K 12.30.14
D.LP Gas Supply
The pressure regulator and hose assembly supplied with LP
models must be used. Replacement pressure regulators and
hose assemblies must be those specified in this manual.
The LP gas supply cylinder used with LP models must be
constructed and marked in accordance with the
specifications for LP gas cylinders of the U.S. Department of
Transportation (DOT).
Cylindersmustbe stored outdoors in a well ventilatedarea out
of the reach of children. Disconnected cylinders must have
threaded valve plugs tightly installed and must not be stored
in a building, garage or any other enclosed area.
Storageofthisapplianceindoorsispermissible only
if it has been disconnected from its fuel supply
(natural gas line or LP gas cylinder).
The LP gas cylinder supply system must be
arranged for vapor withdrawal.
The LP gas cylinder used must include a collar to
protect the cylinder valve.
When an LP model is not in use, the LP gas must
be turned off at the supply cylinder.
The specific size and capacity of the cylinder(s) to
be used: 20 lb. or hard plumbed to propane tank.
Gas Setup for Liquid Propane
1. With burner in place in Outdoor
GreatRoom Company fire pit table or other
installation location and proper sized
orifice inserted in burner neck (see chart on
p.4 for orifice sizing), locate flexible rubber
propane hose and regulator supplied with
this burner.
2. Attach the propane hose to incoming gas
fitting on the gas valve. For Outdoor
GreatRoom Company gas valves and
control panels, this is the lower fitting.
Using two wrenches, one to hold the valve
and one to turn the valve fitting. Tighten
securely. If not using this type of valve, the
included ball valve can be used as shown at
right.
3. Locate the metal flex-line gas hose and
tighten securely to the top valve fitting
following the method described in step 2.
4. Using two wrenches, securely tighten the
flare nut on the free end of the metal flex
hose to the orifice on the burner.
5. For liquid propane installations, the air
shutter may be left open as shown at right
to prevent sooting. To adjust air shutter,
loosen the small securing screw and rotate
air shutter to allow more or less airflow.
Closing the shutter will produce a more
yellow flame but may soot.
IMPROPER INSTALLATION, ADJUSTMENT, ALTERATION SERVICES, OR MAINTENANCE CAN CAUSE INJURY OR
PROPERTY DAMAGE. REFER TO AND UNDERSTAND THIS MANUAL. FOR ASSISTANCE OR ADDITIONAL INFORMATION
CONSULT A QUALIFIED INSTALLER, SERVICE AGENCY, LICENSED TECHNICIAN OR THE GAS SUPPLIER.
Outdoor GreatRoom Co. Control panel kit
Flare Nut
Orifice
Venturi/Air shutter
CHECK ENTIRE SYSTEM FOR LEAKS BEFORE OPERATING
To burner
Ball valve
-OR-

Page | 13 www.outdoorrooms.com Crystal Fire 42435 REV K 12.30.14
Outdoor GreatRoom Co. Control panel kit
Gas Setup for Natural Gas
1. With burner in place in Outdoor GreatRoom
Company fire pit table or other installation
location and proper sized orifice inserted in
burner neck (see chart on p.4 for natural gas
orifice sizing), adjust air shutter to a closed
position (as shown at right, no light visible
through the shutter) by loosening the small
screw on the air shutter and rotating it to a
closed position and re-tightening screw.
2. Locate the included metal flex-line hose and
thread one end onto orifice and tighten
securely with two wrenches.
3. At this point you have two options for plumbing
natural gas. If using a valve assembly such as
The Outdoor GreatRoom Company’s valve kit,
proceed to step 3a. If plumbing directly to a
natural gas line proceed to 3b.
a. Attach the free end of flex hose to the top
(outgoing) flare fitting of control valve and
tighten fully with two wrenches. Plumb
incoming natural gas to the incoming side
of the valve using a 3/8” flare nut. It is
strongly recommended that a manual
shutoff valve is placed in the natural gas
line before it reaches the fire pit’s control
valve.
b. Thread the included ball valve onto the free
end of the metal flex line and plumb
incoming natural gas line to the ball valve
with a 3/8” flare nut.
Flare Nut
Orifice
Venturi/Air shutter
CHECK ENTIRE SYSTEM FOR LEAKS BEFORE OPERATING
To burner
Ball valve

Page | 14 www.outdoorrooms.com Crystal Fire 42435 REV K 12.30.14
6 Lighting and operation
A. This appliance can be lit electronically or with a match.
When lighting, follow these instructions exactly.
B. Before lighting, smell all around the appliance area for
gas. Be sure to smell next to the base of the appliance
because some gas is heavier than air and will settle on
the floor.
WHAT TO DO IF YOU SMELL GAS:
Do not try to light any appliance.
Do not touch any electric switch, do not use any phone
nearby.
Immediately call your gas supplier from a neighbors
phone. Follow gas supplier’s instructions.
If you cannot reach your gas supplier, call the fire
department
FOR YOUR SAFETY, READ BEFORE LIGHTING
WARNING!
If you do not follow these instructions exactly, a fire or explosion may result
causing property damage, personal injury, and/or loss of life.
C. Use only your hand to turn the gas control knob
on propane tank (if equipped), never use tools. If
the valve won’t turn by hand, don’t try to repair it,
call a qualified service technician. Force or
attempted repair may result in a fire or explosion.
D. Do not use the appliance if any part has been
underwater. Immediately call a qualified service
technician to inspect the appliance and replace any
part which has been underwater.
E. The gas pressure regulator provided with this
appliance must be used. This regulator is set for an
outlet pressure of 10.5 inches water column.
Lighting Instructions
1.
Depress button on igniter and verify a spark is
being produced between the electrode tip and
receiving probe.
2.
Ensure control panel valve is in the “OFF” position
and slowly open valve on propane tank. If using
natural gas or whole-house LP, open ball valve. If
not using a control valve, skip this procedure until
step 3.
3.
Depress igniter button and continue holding button
while turning control valve (or ball valve if not
using a control knob valve) to the on position.
Release button once flame is present.
To Extinguish: Turn control valve to “OFF” position or close ball valve. Close valve on
propane tank while not in use.
Igniter button
Initial break-in procedure: When you light the appliance, you may notice that it produces heat
which may have an odor. If you feel this odor is excessive it may require an initial three to four hour
continuous burn on high.
1/4” gap

Page | 15 www.outdoorrooms.com Crystal Fire 42435 REV K 12.30.14
7 Finishing
Personalize your Crystal Fire by building a
decorative surround from noncombustible material
such as bricks, landscaping blocks, or rocks. The
Outdoor GreatRoom Company also sells a variety of
fire pit tables to fit each of our burners as shown
below (not all models shown, see more at
OutdoorRooms.com)
Key Largo fire pit with
CF-1242 burner
42” Black Glass fire pit table
with CF-20 burner
Napa Valley fire pit table
with CF-1224 burner
WARNING
FIRE RISK –HIGH TEMPERATURES
Keep combustible household items away from appliance.
Do NOT obstruct combustion and ventilation air.
Do NOT place combustible items on top of or near appliance.
Keep furniture, draperies away from appliance.
Do NOT use, lantern fuel, kerosene, charcoal lighter fluid, or similar liquids in this appliance.
Combustible materials, flammable liquids, or vapors may ignite.
Uptown fire pit table with
CF-1224 burner
Sierra fire pit table
with CF-2424 burner

Page | 16 www.outdoorrooms.com Crystal Fire 42435 REV K 12.30.14
Symptom
Possible Causes
Corrective Actions
1.
Crystal Fire won’t light.
A.
No LP in tank, or NGmain not turned on.
Check the LP (propane) tank. You may be out of gas. Or check
Natural Gas valve at main.
B.
Plugged burner orifice.
Check the burner orifice for stoppage. Remove stoppage.
2.
Low flames or won’t stay
lit.
A.
Manual shutoff valve (on/off control knob) open
or not in- stalled between LP tank and
appliance.
Close LP tank and manual shutoff valves. Open LP tank valve
first, THEN the manual shutoff valve.
3.
BlueFlames
A.
This is a result of normal operation and flames
will begin to yellow as unit is allowed to burn for
16-20 minutes.
Do nothing.
B.
Improper air/fuel mixture related to air shutter
position.
Close air shutter. (for LP, leave ¼” open, Natural gas 1/16” open)
4.
Metallic noise
A.
Noise is caused bymetal expanding and
contracting as it heats up andcools down,
similar to the sound produced by afurnace or
heating duct. This noise does not affect the
operation or longevity of the appliance.
Do nothing.
5.
DecorativeBeads
crackingor splitting
A.
Heat and/or abrupt temperature changes.
This is a propertyof glass and may happen occasionally. Do
nothing. This is completely normal.
6.
Sparker makes clicking
sound but no visible
spark is produced
A
Sparker is improperly grounded
Refer to section 4-C onPage 9 for grounding instructions . Check
all wire connections.
B.
Ignition or ground wire not plugged in.
C.
Ignitertip set too farfrom grounding probe
Checkthat tip of sparker is within ¼” of grounding probe. Gently
bend ignitertipor grounding probe by hand to achieve a smaller
gap.
7.
Sparker does not spark or
make atickingsound
A.
Battery low, Not installed, Installed incorrectly
Ensure that a fresh AAA battery is installed Positive (+) side facing
outward toward the sparker cap.
B.
Corrosion on battery contacts
Checkcontact at the bottom of the battery cavity for corrosion.
Clean with asmall piece of sandpaper or a file
C.
Battery cap notscrewed down completely
If the cap cannot be screwed down tight enough, the battery will
not make a proper connection withthe sparker and it will not work.
Besure to use a thinsurface such as 20-22gauge sheet metal to
mount sparker in.
8 Troubleshooting

Page | 17 www.outdoorrooms.com Crystal Fire 42435 REV K 12.30.14
Inspect
Maintenance Tasks
Burner Assembly
1
Remove decorative glass and examine burner. Vacuum and wipe
out as needed. Use caution when cleaning these areas
2
Inspect for warping and corrosion. Repair as necessary
3
Check the hose connecting the LP gas cylinder to ensure it is not
damaged. Replace as necessary.
4
Verify air shutter area is clean
Burner Ignition and Operation
1
Verify all gas connections are tight and leak-free
2
Clean burner top, inspect for plugged ports, corrosion, or
deterioration. Replace burner if necessary.
3
Inspect for flame problems.
4
Verify air shutter is clear of dust and debris and is in correct
position for the gas type being used.
5
Inspect orifice for soot, dirt, or corrosion
6
Verify manifold and inlet pressures. Adjust regulator as required.
Gas Hose with Regulator
1
The gas hose with regulator supplied with appliance must be used
for LP installations. The replacement bust be those specified by the
appliance manufacturer
9 Service and maintenance
Although the frequency of appliance servicing and maintenance will
depend on use and the type of installation, a qualified service
technician should perform an appliance check-up annual.
Storage of an appliance indoors is permissible only if the cylinder is
disconnected and removed from the appliance.
The use of a vinyl table cover is highly recommended to keep your
table and burner looking new and ensuring extended trouble-free
operation.
Maintenance and Service Tasks
For service calls: Contact the dealer your product was purchased from first.
Contact the Outdoor GreatRoom Company at 1-866-303-4028 if further assistance is needed.

Page | 18 www.outdoorrooms.com Crystal Fire 42435 REV K 12.30.14
#
Description of Part
Part Number
Qty.
1
Stainless Steel Flex Line
CF-FLEX-TUBE
1
2
#42 Orifice
#42 Orifice
1
3
#31 Orifice
#31 Orifice
1
4
#17 Orifice
#17 Orifice
1
5
#36 Orifice
#36 Orifice
1
6
#21 Orifice
#21 Orifice
1
7
#43 Orifice
#43 Orifice
1
8
Red-handled replacement ball valve
CF-BALL-VALVE
1
9
Control panel for DIY or Outdoor GreatRoom Co. fire pit tables
CT-CP
1
10
Electronic Piezo
CF-Sparker
1
11
Gas Hose with Regulator
CF-HOSE-REG
1
12
Ignition Electrode CF-20/CF-1224/CF-1242/CF-1264/CF-12120/NF-
16/NF-719/NF-737
CF-Electrode
1
13
Ignition Electrode CF-2424/NF-1919/CF-1242-L
CF-2424-ELECTRODE
1
13
Replacement Glass for Crystal Fire (5lb bag)
CFG-D
1
14
CF20 Log Set
CF20-LOG SET
1
15
Grounding wire for Crystal Fires (All models)
CF-GROUND WIRE
1
10 Reference Materials
A.Service Parts List
For more information, you can visit us online at
Http://www.OutdoorRooms.com
Or Call Us At:
1-866-303-4028

Page | 19 www.outdoorrooms.com Crystal Fire 42435 REV K 12.30.14
The Outdoor GreatRoom Company extends the following warranty for Outdoor GreatRoom
outdoor products used in the United States of America or Canada. Dealers and employees of The
Outdoor GreatRoom Company have no authority to make any warranty or authorize any remedies in
addition to or inconsistent with the terms of this warranty. This warranty gives you specific legal
rights. You may also have other rights that vary from state to state.
The Outdoor GreatRoom Company warrants that this Outdoor GreatRoom Outdoor Product (the
“Product”) will be free from defects in material and workmanship for a period of one year from its date
of purchase. Stainless steel parts and assemblies carry a limited lifetime warranty. This warranty is
subject to the conditions, exclusions and limitations described below.
This warranty applies only to the original owner of the Product and is non-transferable. The Outdoor
GreatRoom Company obligation under this warranty does not extend to damages resulting from (1)
assembly, operation or maintenance of the Product not in accordance with the Installation/Assembly
Instructions, Operating Instructions and the Listing Agency Identification Label furnished with the
Product; (2) installation or use which does not comply with local building codes and ordinances; (3)
shipping, improper handling, improper operation, abuse, misuse, accident or unworkmanlike repairs;
(4) use of fuels other than those specified in the Operating Instructions; (5) Installation or use of
components not supplied with the Product or any other components not expressly authorized and
approved in writing by The Outdoor GreatRoom Company; and/or (6) modification of the Productnot
expressly authorized and approved in writing by The Outdoor GreatRoom Company. Any of the
circumstances described in the previous sentence voids this warranty. This warranty is void if the
Product or any component has been removed, repaired, or replaced before The Outdoor GreatRoom
Company has been afforded a reasonable opportunity to inspect the Product.
ThiswarrantyislimitedtothereplacementorrepairofdefectivecomponentsorworkmanshipandThe
Outdoor GreatRoom Company may fully discharge its obligations under this warranty by repairing or
replacing, at its discretion, the defective components. The Outdoor GreatRoom Company will provide
replacement parts at no charge and will pay reasonable and necessarylabor and freight costs related to
replacing or repairing defective components under this warranty. The maximum amount recoverable
under this warranty is limited to the purchase price of the Product and, if The Outdoor GreatRoom
Company is unable to provide replacement or repair in an expedient and cost-effective manner, The
Outdoor GreatRoom Company may discharge all obligations under this warranty by refunding the
purchase price of the Product.
EXCEPT TO THE EXTENT PROVIDED BY LAW, THE OUTDOOR GREATROOM COMPANY
MAKES NO EXPRESS WARRANTIES OTHER THAN THE WARRANTY EXPRESSED HEREIN. THE
DURATION OF ANY IMPLIED WARRANTY IS LIMITED TO THE DURATION OF THE WARRANTY
SPECIFIED ABOVE. IN NO EVENT SHALL THE OUTDOOR GREATROOM COMPANY BE LIABLE
FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES CAUSED BY DEFECTS IN THE
PRODUCT. Some states do not allow limitations on how long an implied warranty lasts, or do not
allow exclusion or limitation of incidental or consequential damages, so these limitations may not
apply to you.
To obtain service under this warranty, you must:
1.Send written notice of the claimed condition to: The Outdoor GreatRoom Company, 2015
Silver Bell Road, #195, Eagan, MN 55122.
2.Affirm that you are the original owner of the Product.
3.Provide The Outdoor GreatRoom Company reasonable opportunity to investigate the claim,
including reasonable opportunity to inspect the Product prior to any repair or replacement work
and before the Product or any component of the Product has been removed.
B. Limited One Year Warranty
The Outdoor GreatRoom Company
Outdoor Products Limited Warranty