Outdoor GreatRoom Company RSTL User manual

Installation Instructions for All Ready to Finish
See Through Outdoor Fireplaces
(RSTL)
Ready to Finish Outdoor Fireplace
outdoorrooms.com

IMPORTANT
Please consult your Crystal Fire® Plus instruction manual for detailed
instructions and important information related to the burner
installation including: lighting and operating instructions, safety
information, and proper tightening of connections with two wrenches.
DO NOT ATTEMPT TO INSTALL CRYSTAL FIRE®PLUS BURNER
WITHOUT CONSULTING THE CRYSTAL FIRE®PLUS
OWNER’S MANUAL.
CONTENTS
1. About Your Fireplace 2
a. Required Tools
outdoorrooms.com42515 REV A 02-28-20
!!
1
b. Included With Your Fireplace
2. Assembly Instructions
a. Unpacking
3. Setting Up Your Burner
a. Natural Gas Connections
b. Electrical Installation
c. Burner Maintenance
d. Self-Contained Propane Cylinder Installation
e. Final Installation Steps
4. Miscellaneous
a. Fire Media Installation
b. Wind Guard Installation
5. Operating Instructions
6. Warnings
3
4
7
9
10
c. Finishing

outdoorrooms.com 2
• Utility Knife -
To cut and remove packaging
• 2 Open Ended Wrenches (1X 7/8” Wrench and 1X 3/4” Wrench)-
To secure gas connections
•Phillips Screw Driver (Do not use a drill to assemble)-
For assembly and attachment of bottle opener
1. ABOUT YOUR FIREPLACE
Set of Glass Wind Guards and
Glass Guard Clip Hardware
(1)
Fully Assembled Fireplace
with CFP DSI Burner
(See Crystal Fire®Plus manual for size specifcations)
(1)
A. REQUIRED TOOLS
B. INCLUDED WITH YOUR FIREPLACE

outdoorrooms.com 3
ASSEMBLY INSTRUCTIONS
•Do not discard any packaging until assembly is complete and unit is tested.
•Keep all included manuals in a safe place for future reference.
• Two people are recommended to remove replace from packaging.
• Place replace in desired location. Refer to image 2.1 for recommened
placement. It is recommended to place the large circular opening over the
natural gas pipe if not using self-contained propane cylinder.
Exposed edges may be sharp, use leather gloves
when removing packaging and handling the base.
2.
!!
A. UNPACKING
WARNING
Image 2.1
(Cross section of fireplace.)
GAS LINE LOCATION

outdoorrooms.com 4
SETTING UP YOUR BURNER
ATTENTION
Read and understand your Crystal Fire® Plus owner’s manual before
beginning burner hookups or using the device.
DO NOT USE TEFLON TAPE OR PIPE DOPE ON FLARE FITTINGS.
3.
!
!
A. NATURAL GAS CONNECTIONS
• For hard piped installations: Position replace over gas line as shown in
Image 3.1. Connect the gas supply line (not included) to the 1/2” male are
tting on the valve. USE TWO WRENCHES TO ENSURE A GAS TIGHT
CONNECTION.
•Run gas line pipe up through large round opening in bottom of base
• See Crystal Fire®Plus instructions for burner installation.
• All gas connections were completed at the factory. Performing a leak test on
all connections is required.
• It is recommended that this unit is installed as hard piped.
• Check all connections for leaks. If needed, tighten connection with
two wrenches and re-check for leaks.
GAS LINE ACCESS
ELECTRICAL ACCESS
Image 3.1
(Cross section top view of fireplace)
IMPORTANT
Please consult your Crystal Fire® Plus instruction manual for detailed
instructions and important information related to the burner installation
including: lighting and operating instructions, safety information, and proper
tightening of connections with two wrenches.
DO NOT ATTEMPT TO INSTALL CRYSTAL FIRE®PLUS BURNER WITHOUT
FIRST CONSULTING THE CRYSTAL FIRE®PLUS OWNER’S MANUAL.
!!

outdoorrooms.com 5
C. BURNER MAINTENANCE
• Before doing any maintenance on
burner or DSI box, it is recommended to
place a protective barrier, such as a towel
or cardboard, over stainless steel caps.
•Carefully lift burner out of burner pan
and rest on side caps as shown in
Image 3.3
•To access underneath burner, the access
plate coverings can be removed. Using a
phillips screwdriver, remove bolts holding
access plate to pan as shown in Image
3.4. Carefully lift up both access plates
and tilt inwards to remove. Take care not
to scratch stainless steel interior side
panels.
• Tighten all connections with two
wrenches and perform a leak test after
any burner or DSI maintenance.
B. ELECTRICAL INSTALLATION
• Feed electrical wiring up through smaller hole in base pan as shown in
Image 3.2. Wire electrical into junction box.
Image 3.2
Cross section of fireplace.
ELECTRICAL LOCATION
Image 3.4
Image 3.3
PROTECTIVE BARRIER HERE

outdoorrooms.com 6
• Remove access door from end of
replace.
• Using two wrenches, disconnect
ex line and connect regulator hose.
A separate adaptor can be
purchased serperatly to allow
propane regulator hose to attach to
DSI. See reference materials at end
of Crystal Fire® Plus Manual.
• Tilt self-contained propane
cylinder and position within
replace in large circular hole in
base pan. As shown in Image 3.5.
D. SELF-CONTAINED PROPANE CYLINDER INSTALLATION
HAND TIGHTEN, DO NOT USE A WRENCH FOR THIS CONNECTION.
!
!ATTENTION
E. FINAL INSTALLATION STEPS
• Once gas, electical connections
are made, and a leak test is
performed,replace access panel
on front of replace.
•Using supplied screws attach
access panel to frame. Reference
red “X’s” in Image 3.6 for screw
locations.
x
x
x
x
x
x
Image 3.6
Image 3.5

outdoorrooms.com 7
4. MISCELLANEOUS
A. FIRE MEDIA INSTALLATION
WARNING
DO NOT OPERATE CRYSTAL FIRE® PLUS BURNER WITHOUT GLASS BEADS OR
OTHER APPROVED FIRE MEDIA.
!!
•Scatter glass beads, lava rock, or other approved re media evenly across
entire burner surface. Image 4.1
Media not included with fireplace, a seperate order is needed to obtain media.
B. WIND GUARD INSTALLATION
• Install glass guard clip screws into
backside of glass guard clips.
•Place spacer into glass guard clip as
shown in Image 4.2.
• Carefully lower glass wind guards into
glass guard clips as shown in Image 4.3
• Using a Phillips screwdriver, lightly
tighten the clip screws. Do not
overtighten.
Image 4.2
Image 4.1
Image 4.3

outdoorrooms.com 8
C. FINISHING
Fireplace is designed to be custom nished. Interior frame studs can be
located by screw location on front and back of replace.
Reference the red “X’s” in Image 4.4 below.
Image 4.4
xx x x
ATTENTION
Care must be taken around stainless steel interior parts.
Stainless steel can be easily scratched.
!
!

outdoorrooms.com 9
OPERATING INSTRUCTIONS
IMPORTANT
WARNING
Before operating your RSTL ensure all gas connections are properly
tightened and thoroughly leak checked. Refer to the Crystal Fire®Plus
manual for information on proper leak checking and other critical safety
information.
FIRE OR EXPLOSION HAZARD
If you do not follow these instructions exactly, a re or explosion may result
causing property damage, personal injury, or loss of life.
5.
!
!
!
!
Verify control switch is in OFF position. See Image 5.1.
If operating on a self-contained propane
cylinder, ensure cylinder valve is CLOSED. If
operating on a hard-piped system, ensure main as
supply shut-o valve and all other valves in gas
system are OPEN.
If operating on a self-contained propane cylinder,
slowly open cylinder valve.
Turn control switch to ON position. A 1-2 second
delay will occur while control module runs diagnostics.
Sparking will then occur at the ignition electrodes. See
Image 5.2. Gas valve will open and burner will ignite.
If burner does not ignite within 12 second ignition
window, turn control switch to OFF position and wait
5 minutes to allow gas to dissipate before attempting
ignition again. DO NOT ATTEMPT TO LIGHT BURNER
IF YOU SMELL GAS.
While burner is operating, the DSI system will
continuously monitor the presence of a ame. If ame
signal is lost, the system will attempt re-ignition for up
to 12 seconds. If ame signal is lost for more than 12
seconds, the system will shut down.
TO EXTINGUISH
Turn control switch to OFF position.
See Image 5.1
If using a self-contained propane cylinder, close
valve.
ON
OFF
REMOTE
SPARK LOCATION
SEE DETAIL A
Image 5.1
Image 5.2

outdoorrooms.com 10
IMPORTANT
Please consult your Crystal Fire® Plus instruction manual for detailed
instructions and important information related to the burner installation
including: lighting and operating instructions, safety information, and proper
tightening of connections with two wrenches.
DO NOT ATTEMPT TO INSTALL CRYSTAL FIRE®PLUS BURNER WITHOUT
FIRST CONSULTING THE CRYSTAL FIRE®PLUS OWNER’S MANUAL.
WARNING
After consulting the manual and following instructions, remember: before
operating, all gas connections must be fully checked for leaks.
6. WARNINGS
!
!
!
!

outdoorrooms.com
Thank you for purchasing an
Outdoor GreatRoom Company
product! This re pit was made
with pride in the USA.
Warranty: Fire pit tables are covered under a 1 year
manufacturer’s warranty.
Please visit http://www.outdoorrooms.com/product-registration
to register your product.
14400 Southcross Drive West • Suite 100 • Burnsville, MN 55306
Toll Free: 1-866-303-4028 • [email protected]